AAT NVIP-3SD-6300/30/F (NVIP-3DN3630SD/IRH-2) Instrukcja obsługi

User’ s ma n ual

(shor t for m )

NVIP-3SD-6300/30/F

NVIP-3SD-6300/30/F - User’s manual (short form) ver 1.0

2

IMPORTANT SAFEGUARDS AND WARNINGS

EMC (2014/30/EU) and LVD (2014/35/UE) Directives

CE Marking

Our products are manufactured to comply with requirements of the following directives and national

regulations implementing the directives:

• Electromagnetic compatibility EMC 2014/30/EU.

• Low voltage LVD 2014/35/UE with further amendment. The Directive applies to electrical

equipment designed for use with a voltage rating of between 50VAC and 1000VAC as well as

75VDC and 1500VDC.

WEEE Directive 2012/19/EU

Information on Disposal for Users of Waste Electrical and Electronic Equipment

This appliance is marked according to the European 1000VAC Directive on Waste Electrical and

Electronic Equipment (2012/19/EU) and further amendments. By ensuring this product is disposed of

correctly, you will help to prevent potential negative consequences for the environment and human health, which

could otherwise be caused by inappropriate waste handling of this product.

The symbol on the product, or the documents accompanying the product, indicates that this appliance may not be

treated as household waste. It shall be handed over to the applicable collection point for used up electrical and

electronic equipment for recycling purpose. For more information about recycling of this product, please contact

your local authorities, your household waste disposal service or the shop where you purchased the product.

RoHS Directive 2011/65/EU

Out of concern for human health protection and friendly environment, we assure that our products falling under

RoHS Directive regulations, regarding the restriction of the use of hazardous substances in electrical and

electronic equipment, have been designed and manufactured in compliance with the above mentioned

regulations. Simultaneously, we claim that our products have been tested and do not contain

hazardous substances whose exceeding limits could have negative impact on human health or natural

environment

Information

The device, as a part of professional CCTV system used for surveillance and control, is not designed for self

installation in households by individuals without technical knowledge.

Excluding of responsibility in case of damaging data on a disk or other devices:

The manufacturer does not bear any responsibility in case of damaging or losing data on a disk or other devices

during device operation.

WARNING!

PRIOR TO UNDERTAKING ANY ACTION THAT IS NOT DESCRIBED FOR THE GIVEN PRODUCT IN

USER’S MANUAL AND OTHER DOCUMENTS DELIVERED WITH THE PRODUCT, OR IF IT DOES

NOT ARISE FROM THE USUAL APPLICATION OF THE PRODUCT, MANUFACTURER MUST BE

CONTACTED UNDER THE RIGOR OF EXCLUDING THE MANUFACTURER’S RESPONSIBILITY FOR

THE RESULTS OF SUCH AN ACTION.

NVIP-3SD-6300/30/F - User’s manual (short form) ver 1.0

3

IMPORTANT SAFEGUARDS AND WARNINGS

WARNING!

THE KNOWLEDGE OF THIS MANUAL IS AN INDESPENSIBLE CONDITION OF A PROPER

DEVICE OPERATION. YOU ARE KINDLY REQUSTED TO FAMILIRIZE YOURSELF WITH

THE MANUAL PRIOR TO INSTALLATION AND FURTHER DEVICE OPERATION.

WARNING!

USER IS NOT ALLOWED TO DISASSEMBLE THE CASING AS THERE ARE NO USER

-SERVICEABLE PARTS INSIDE THIS UNIT. ONLY AUTHORIZED SERVICE PERSONNEL

MAY OPEN THE UNIT

INSTALLATION AND SERVICING SHOULD ONLY BE DONE BY QUALIFIED SERVICE

PERSONNEL AND SHOULD CONFORM TO ALL LOCAL REGULATIONS

1. Prior to undertaking any action please consult the following manual and read all the safety and operating

instructions before starting the device.

2. Please keep this manual for the lifespan of the device in case referring to the contents of this manual is

necessary;

3. All the safety precautions referred to in this manual should be strictly followed, as they have a direct

influence on user’s safety and durability and reliability of the device;

4. All actions conducted by the servicemen and users must be accomplished in accordance with the user’s

manual;

5. The device should be disconnected from power sources during maintenance procedures;

6. Usage of additional devices and components neither provided nor recommended by the producer is forbidden;

7. You are not allowed to use the camera in high humidity environment (i.e. close to swimming pools, bath tubs,

damp basements);

8. Mounting the device in places where proper ventilation cannot be provided (e. g. closed lockers etc.) is not

recommended since it may lead to heat build-up and damaging the device itself as a consequence;

9. Mounting the camera on unstable surface or using not recommended mounts is forbidden. Improperly

mounted camera may cause a fatal accident or may be seriously damaged itself. The camera must be mounted

by qualified personnel with proper authorization, in accordance with this user’s manual;

10. Device should be supplied only from a power sources whose parameters are in accordance with those

specified by the producer in the camera technical datasheet. Therefore, it is forbidden to supply the camera

from a power sources with unknown parameters, unstable or not meeting producer’s requirements;

Due to the product being constantly enhanced and optimized, certain parameters and functions

described in the manual in question may change without further notice.

We strongly suggest visiting the www.novuscctv.com website in order to access the newest manual.

NVIP-3SD-6300/30/F - User’s manual (short form) ver 1.0

4

TABLE OF CONTENTS ..................................................................................................... 4

1. FOREWORD INFORMATION ................................................................................... ..5

1.1. General characteristics ......................................................................................... 5

1.2. Technical specification .................................................................................... ...6

1.3. Camera dimension ........................................................................................... ...7

1.4. Package contents ............................................................................................... ...7

2. START-UP AND INITIAL IP CAMERA CONFIGURATION ................................. 8

2.1. Description of connectors and control tools ........................................................ 8

2.2. Connecting ethernet cable ................................................................................... 9

2.3. Camera mounting .............................................................................................. 10

2.4. Starting the IP camera ........................................................................................ 11

2.5. Initial configuration via the web browser .......................................................... 12

2.6 Security recommendations for network architecture and configuration ........... 13

3. NETWORK CONNECTION UTILIZING WEB BROSWER ................................ 14

3.1. Recommended PC specification for web browser ............................................. 14

3.2. Connection with IP camera via web browser ..................................................... 14

4. WWW INTERFACE - WORKING WITH IP CAMERA ......................................... 16

4.1. Displaying live video. ......................................................................................... 16

4.2. PTZ camera control . .......................................................................................... 17

5. ELECTRIC CONNECTORS AND ACCESORIES ................................................. 18

5.1. SD card installation ........................................................................................... 18

5.2. Alarm input and output connection .................................................................... 18

6. RESTORING FACTORY DEFAULTS ..................................................................... 19

6.1. Restoring software factory defaults via web browser ........................................ 19

6.2. Restoring software factory defaults via NMS IPTool……… .. ………………..19

6.3 Restoring hardware factory defaults by hardware .. ………………..…………...20

TABLE OF CONTENTS

NVIP-3SD-6300/30/F - User’s manual (short form) ver 1.0

5

1. FOREWORD INFORMATION

1.1. General Characteristics

• Integrated speed dome camera day/night

• Mechanical IR cut filter

• Ability to work in the infrared-built-in IR LED

• Resolution of the sensor: 3.0 megapiksels

• Sensitivity: from 0,01 Lux with IR Off

• Lens type: motor-zoom with automatic Iris and auto-focus f=4.5-135mm/F1.6-F4.4

• 8 patrols (16 presets)

• 4 patterns (up to 180 seconds )

• Time tasks: 8

• 2 scanning modes

• 360 presets

• Optical Zoom: 30x

• 7 alarm input

• 1 alarm output (NO/NC)

• MicroSD card up to 128GB

• OSD menu

• Auto-flip

• Compression method H.264, H.265 or MJPEG

• Dual audio

• Vide resolution: 2048 x 1536

• Support RTP/RTSP standard

• Support up to 3 streams

• Network connection control

• Build in web server - possibility to configure camera trough web browser

• Ability to broadly define the system's response to alarm events: email with attachments, save file

to FTP server, trigger alarm output, HTTP notification, PTZ function call

• Full PTZ operational via internet browser or NMS software (NOVUS MANAGEMENT

SYSTEM)

• Protocol support: ONVIF Profile S/R, TCP/IP, UDP, DHCP, DDNS, NTP, RTSP, SMTP, FTP,

PPPoE

• Software: NMS (NOVUS MANAGEMENT SYSTEM - recording, live preview, playback of

recording and much more)

• Wall bracket included

• Power Supply: 24 VDC or 24VAC

• Face recognition - advanced analytic function, available only with selected models of the NVR

6000 series.

FOREWORD INFORMATION

NVIP-3SD-6300/30/F - User’s manual (short form) ver 1.0

6

1.2. Technical specification

FOREWORD INFORMATION

IMAGE

Image Sensor

3 MPX CMOS sensor 1/2.8” SONY Exmor R STARVIS

Number of Effective Pixels

2065 (H) x 1553 (V)

Min. Illumination

0.03 lx/F1.6 - color mode,

0.01 lx/F1.6 - B/W mode,

0 lx (IR on) - B/W mode

Electronic Shutter

auto: 1/25 s ~ 1/100000 s

Wide Dynamic Range (WDR)

yes (double scan sensor), 120dB

Digital Noise Reduction (DNR)

3D

Defog Function (F-DNR)

yes

Highlight Compensation (HLC)

yes

Back Light Compensation (BLC)

yes

LENS

Optical Zoom

30x

Lens Type

motor-zoom, auto-iris function, f=4.5 ~ 135 mm/F1.6 ~ F4.4

Auto-focus

zoom trigger, day/night mode trigger

DAY/NIGHT

Switching Type

mechanical IR cut filter

Switching Mode

auto, manual, time

Visible Light Sensor

yes

NETWORK

Stream Resolution

2048 x 1536 (QXGA), 1920 x 1080 (Full HD), 1280 x 720 (HD), 640 x

480 (VGA), 320 x 240 (QVGA)

Frame Rate

30 fps for 2048 x 1536 (QXGA) and lower resolutions

Multistreaming Mode

3 streams

Video/Audio Compression

H.264, H.265, MJPEG/G.711

Number of Simultaneous

Connections

max. 6

Bandwidth

70 Mb/s in total

Network Protocols Support

HTTP, TCP/IP, IPv4/v6, Multicast, FTP, DHCP, DNS, DDNS, NTP, RTSP,

RTP, UPnP, SNMP, QoS, IEEE 802.1X, PPPoE, SMTP, SSL, ICMP, Unicast

ONVIF Protocol Support

Profile S/G

Camera Configuration

from Internet Explorer browser

languages: Polish, English

Compatible Software

NMS, NVR-6000 Viewer

Mobile applications

SuperLive Plus (iPhone, Android)

PTZ

Preset Commands

360

Tours

8 (up to 16 presets per tour)

Auto-Scans

2

Patterns

4 (max. 180 s for each pattern)

Tilt/Pan Range

0° ~ 93°/360° (continuous)

Pan/Tilt Speed

up to 80°/s (proportional to zoom)

Preset Speed

up to 150°/s

Protocols

Pelco-D, Pelco-P

OTHER FUNCTIONS

Access Password

number of characters: 4 numbers

Privacy Zones

4

Motion Detection

yes

Video Content Analysis (VCA)

face detection

Image Processing

180˚ image rotation, sharpening, mirror effect

System Reaction to Alarm Events

e-mail with attachment, saving file on SD card, alarm output

activation, HTTP notification, PTZ

NVIP-3SD-6300/30/F - User’s manual (short form) ver 1.0

7

FOREWORD INFORMATION

1.3. Camera dimensions (mm)

Camera NVIP-3SD-6300/30/F

1.4. Package contents

After you open the package make sure that the following elements are inside:

• IP camera

• Accessories bag

• Short version of user’s manual

• Wall bracket

• 24VAC Power supply

If any of this elements has been damaged during transport, pack all the elements back into the original

box and contact your supplier for further assistance.

CAUTION!

It is forbidden to use – as the camera signal source – PoE equipment (adapters, etc.) not

compatible with IEEE 802.3at/af standard (items called “passive PoE power supply”). Damages

that results from the usage of improper power supply source are not covered by the warranty.

IR LED

LED Number

10

Range

up to 180 m (depends on current optical zoom value)

Angle

up to 45° (depends on current optical zoom value)

INTERFACES

Audio Input/Output

1 x Jack (3.5 mm)/1 x Jack (3.5 mm)

Alarm Input/Output

7 (NO/NC)/1 relay type

RS-485

yes

Network Interface

1 x Ethernet - RJ-45 interface, 10/100 Mbit/s

Memory Card Slot

microSD - capacity up to 128GB

INSTALLATION PARAMETERS

Dimensions (mm)

216 (Ф) x 348 (H) with bracket: 216 (W) x 385 (H) x 350 (L)

Weight

5.4 kg with bracket: 6.1 kg

Degree of Protection

IP 66 (details in the user’s manual)

Enclosure

aluminium, white, IK10 impact rating, in set: outdoor housing

(integrated with the camera), wall mount bracket

Power Supply

24 VDC/24 VAC

Power Consumption

15 W, 35 W (IR on), 65 W (IR and heater on)

Surge protection

TVS 6000 V

Operating Temperature

-30°C ~ 60°C

Built-in Heater/Fan yes/no

NVIP-3SD-6300/30/F - User’s manual (short form) ver 1.0

8

START-UP AND INITIAL IP CAMERA CONFIGURATION

2. START-UP AND INITIAL IP CAMERA CONFIGURATION

CAUTION!

If the device was brought from a location with lower temperature, please wait until it reaches

the temperature of location it is currently in. Turning the device on immediately after bringing it

from a location with lower ambient temperature is forbidden, as the condensing water vapour

may cause short-circuits and damage the device as a result.

Before starting the device familiarize yourself with the description and the role of particular

inputs, outputs and adjusting elements that the device is equipped with.

2.1 Description of connectors and control tools

1. 100 Mb/s Ethernet port (PoE RJ-45 connector)

2. Audio input (Jack 3.5mm)

3. Audio output (Jack 3.5mm)

4. BNC CVBS video output

5. Alarm input/output terminal block

6. RS485 terminal block

7. Power supply 24VAC/24VDC

1

2

3

4

5

6

7

NVIP-3SD-6300/30/F - User’s manual (short form) ver 1.0

9

START-UP AND INITIAL IP CAMERA CONFIGURATION

2.2. Connecting ethernet cable

To maintain tightness of ethernet cable connection, please follow instruction below:

1. Unscrew the nut (2) from the connector cover (1), mount the sealing ring on the socket (3).

2. Route the network cable through the components (1) and (2). Plug the RJ-45 connector into the

socket (3).

3. Screw the connector cover (1) on the socket (3). Inside the upper part of the connector cover (1) push

in to the stop the seal of the cable (4) - the seal is cut to insert on the network cable.

4. Tighten up to the stop nut (2).

CAUTION!

The declared degree of protection of the camera relates to its housing and does not take into

account the possibility of moisture infiltration into the interior of the camera by connecting

cables. Connection cables protection through i.e. sealing up is the responsibility of the camera

installer. The manufacturer is not liable for any damages to the camera caused as a result of

failing in performing that activity by installer, which also means that camera damaged in that

way is not subject to warranty repairs.

Camera power supply connector is not hermetic. User should seal this connector by himself.

Camera can be supplied using external power supply unit corresponding with the camera parameters

CAUTION!

In order to provide protection against voltage surges/lightning strikes, usage of appropriate surge

protectors is advised. Any damages resulting from surges are not eligible for service repairs.

2

3

2

1

4

Schema of 12VDC power supply connector

NVIP-3SD-6300/30/F - User’s manual (short form) ver 1.0

10

2.3. Camera mounting

To mount a camera please follow the instructions below:

• Unscrew the top camera part and unplug wires (1).

• Put the bracket to the wall in a desired mounting place (with cable hole). Take the drill pattern

and mark future drilling holes for screws and wires.

• Drill holes in accordance with previously done markings and base hole placement.

• Mount the camera bracket using the supplied plugs and screws.

• Mount the muff to the bracket (2).

• Mount top camera part to the muff (3).

• Mount camera to the bracket (mount to hinge) and plug in wires. Move camera to bracket and

tighten to the stop counter screws (4).

CAUTION!

Please note that the wall or ceiling must have enough strength to support the IP Camera.

CAUTION!

In order to obtain declared degree of protection please seal the camera bracket to prevent water

getting inside. Furthermore, when installing the bracket on rough/uneven surfaces, please

additionally seal the junction with appropriate sealing mass. Please pay special attention to any

mounting holes and if they are a loop-through ones, seal them too.

START-UP AND INITIAL CAMERA CONFIGURATION

1

3

2

4

NVIP-3SD-6300/30/F - User’s manual (short form) ver 1.0

11

2.4. Starting the IP camera

To run NOVUS IP camera you have to connect included power supply.

You can also connect it directly via power supply adapter with parameters compatible with camera

power supply specification.

After connecting power status red LED should light on. Initialization process is then started which can

take about 2 minutes. You can then proceed to connect to the camera via web browser.

The recommended way to start an IP camera and perform its configuration is a connection directly

to the network switch which is not connected to other devices. To obtain further information about

network configuration parameters (IP address, gateway, network mask, etc.) please contact your

network administrator.

• Connection utilizing external power supply and network switch

• Connection utilising external power supply and network switch

START-UP AND INITIAL CAMERA CONFIGURATION

IP Camera

Network transmission

Network Switch

Computer

Network transmission

IP Camera

Network transmission - cross over cable

Computer

NVIP-3SD-6300/30/F - User’s manual (short form) ver 1.0

12

2.5. Initial configuration via the web browser

The default network settings for NVIP-3SD-6300/30/F camera are :

1. IP address= 192.168.1.200

2. Network mask - 255.255.255.0

3. Gateway - 192.168.1.1

4. User name - root

5. Password - pass

Knowing the camera’s IP address you need to appropriately set PC IP address, so the two devices can

operate in one network subnet ( e.g. for IP 192.168.1.1, appropriate address for the camera ranges from

192.168.1.2 to 192.168.1.254, for example 192.168.1.60). It is not allowed to set the same addresses for

camera and PC computer

You can either set a network configuration (IP address, gateway, net mask, etc.) of NOVUS IP camera

yourself or select DHCP mode (DHCP server is required in this method in target network) by using

web browser or by NMS software. When you use DHCP server check IP address lease and its linking

with camera MAC address to avoid changing or losing IP address during device operation or network/

DHCP server breakdown. You have to remember to use a new camera IP address after changing

network parameters.

After network setting configuration has been done, the camera can be connected to a target network.

START-UP AND INITIAL CAMERA CONFIGURATION

NVIP-3SD-6300/30/F - User’s manual (short form) ver 1.0

13

2.6. Security recommendations for network architecture and configuration

CAUTION!

Below are shown security recommendations for network architecture and configuration

of CCTV systems that are connected to the Internet to reduce the risk

of unauthorized interference with the system by a third party.

1. Absolutely change the default passwords and user names (if the device gives this possibility) of

all applied network devices (recorders, cameras, routers, network switches, etc.) to the

severely complexity password. Use lowercase and uppercase letters, numbers, and special characters

if there is such possibility.

2. Depending on the available functionality in the order to restrict access to the used network devices at

the administrator account level, it is recommended to configure the users accounts accordingly.

3. Do not use DMZ function (Demilitarized zone) in your router. Using that function you open the

access to recorder system from the Internet on all ports, which gives possibility for an unauthorized

interference with the system.

Instead of DMZ use port forwarding redirect only the ports which are necessary for the performance

of the connection (detailed information about ports of communication in different models of recorders,

cameras, etc. can be found in the operating instructions).

4. Use routers with firewall function and make sure it is enabled and properly configured.

5. It is recommended to change the default network communication port numbers of used devices

if there is such possibility.

6. If used network devices has a UPnP feature and it is not used, turn it off.

7. If used network devices has a P2P feature and it is not used, turn it off.

8. If used network devices support HTTPS protocol for connection, it is recommended to use it.

9. If used network devices support IP filtering for authorized connections function, it is recommended

to use it.

10. If used recorder has two network interfaces it is recommended to use both of them to physically

separate network for cameras and network for Internet connection. The only device in the system,

accessible from Internet will be recorder - there will be no physically access directly to any camera.

START-UP AND INITIAL CAMERA CONFIGURATION

NVIP-3SD-6300/30/F - User’s manual (short form) ver 1.0

14

3. NETWORK CONNECTION UTILIZING WEB BROSWER

3.1. Recommended PC specification for web browser connections

Requirements below apply to connection with an IP camera, assuming smooth image display

in 2048x1536 resolution and 30 fps speed.

1. CPU Intel i7 3 GHz or faster

2. RAM Memory min. 6 GB

3. VGA card Nvidia GeForce 1GB

4. OS Windows 7 / 8 / 8.1 / 10

5. Network card 100/1000 Mb/s

3.2. Connection with IP camera via web browser

CAUTION!

To maintain correct operation as snapshot or video recording you must enable the browser as an

administrator.

You have to enter camera IP address in the web browser address bar. If IP address is correct user login

window will be displayed:

In the Language box you can change the display language. Available languages: Polish, English and

other.

CAUTION!

Default user is root and default password is pass. The camera will ask you to change the default

password during the first login (recommended). To do this, check the Modify password option and then

enter and confirm the new password. In order to log into the camera without changing the password,

press the OK button. The message will be displayed each time you log in, until you change your

password, or select the Do not show again option.

NETWORK CONNECTION UTILIZING WEB BROWSER

NVIP-3SD-6300/30/F - User’s manual (short form) ver 1.0

15

If you’re first time running the camera, you will see screen as below.

To correctly camera working, you need a NetIPCamera plugin. You have to download and install it.

To do it just click Save button, than Run, close IE browser, choose the language, click Install button

and ay the end click Finish button. After installation run IE browser.

CAUTION!

In Windows Vista/7/8/8.1/10 the ActiveX applet may be blocked by Windows Defender or User

account control. In such case you should allow to run this applet, or simply disable these functions.

CAUTION!

If the installation fails, changing security settings for the IE browser is required. In order to do that,

please select Enable for Initialize and script ActiveX controls not marked as safe and Download

unsigned ActiveX controls option

NETWORK CONNECTION UTILIZING WEB BROWSER

NVIP-3SD-6300/30/F - User’s manual (short form) ver 1.0

16

4. WWW INTERFACE - WORKING WITH IP CAMERA

4.1 Displaying live video

1. Camera menu

• Live - opens the camera live video

• Config - opens the camera configuration menu

• Search - opens the camera playback

• Logout - button used to log out the current user

2. The buttons for changing the displayed stream and fluency - let you change the displayed stream to

Main stream, Sub stream and Third stream, and also allow you to choose between Real-time, Balanced

and Fluent fluency.

3. Alarm icons - icons showing the current status of some camera alarms.

4. Live video preview window

5. Image settings buttons - these buttons change the picture display mode in the live video preview

Original size Adapt

Proper size Full screen

6. Function buttons - these buttons allow you to enable / disable some of functions

Stop live view Snapshot Zoom In/Zoom Out (digital)

Enable/disable Audio Start recording

PTZ control Enable two-way audio

WWW INTERFACE - WORKING WITH IP CAMERA

3

4

1

2

5

6

NVIP-3SD-6300/30/F - User’s manual (short form) ver 1.0

17

5. ELECTRIC CONNECTORS AND ACCESORIES

5.1. SD card installation

Camera supports SD cards up to a maximum size of 128GB. In order to install the card properly,

please follow the instructions below:

• Turn off the camera.

• Unscrew the camera service panel (1).

• Mount microSD card in the socket (2).

• Screw the camera service panel (1).

• Turn on the camera.

• Check the SD card by checking its capacity in the “System” -> “SD Card” tab.

5.2. Alarm input and output connection

Standard alarm input connection Standard alarm output connection

WWW INTERFACE - WORKING WITH IP CAMERA

4.2 Camera control from via browser

1. PTZ camera menu sections

PTZ and lens control

PTZ slider speed

PTZ functions

Function menu

PTZ function programming section

2. Description of selected PTZ camera menu functions

- unavailable functions

- IR LED - available modes: AUTO, ON and OFF

- scan function - camera rotate evenly to one side

- the camera performs all programmed cruises

- preset functions

- save actual position to current preset

- call selected preset

- delete selected preset from memory

1

2

3

4

5

NVIP-3SD-6300/30/F - User’s manual (short form) ver 1.0

18

5. ELECTRIC CONNECTORS AND ACCESORIES

5.1. SD card installation

Camera supports SD cards up to a maximum size of 128GB. In order to install the card properly,

please follow the instructions below:

• Turn off the camera.

• Unscrew the camera service panel.

• Mount microSD card in the socket (1).

• Screw the camera service panel.

• Turn on the camera.

• Check the SD card by checking its capacity in the “System” -> “SD Card” tab.

5.2. Alarm input and output connection

Standard alarm input connection Standard alarm output connection

ELECTRIC CONNECTORS AND ACCESORIES

Alarm input

(INA)

Alarm input

(GND)

IP camera

Switch or

sensor

Indicator

power supply

IP camera

Indicator

Alarm

output

(COM)

Alarm

output

(OPEN)

1

NVIP-3SD-6300/30/F - User’s manual (short form) ver 1.0

19

RESTORING FACTORY DEFAULTS

6. RESTORING FACTORY DEFAULTS

NOVUS IP cameras allow to restore defaults via:

• software (via web browser )

• software (via NMS IPTool)

• hardware (using reset button (RST))

6.1. Restoring software factory defaults via web browser

User can restore default settings of the IP camera except network settings (optional). To restore to

default settings go to: “Advanced Config -> Config Backup & Restore” tab. Process of restoring takes

about two minutes.

6.2. Restoring software factory defaults via NMS IPTool

NMS IPTool (version 1.23.4 or later) allows to restore factory defaults. To restore settings find camera

via NMS IPTool, click right mouse button and choose “ Restore default configuration”. Next, within 10

seconds, it is required to turn the camera power off and on.

NVIP-3SD-6300/30/F - User’s manual (short form) ver 1.0

20

6.3. Restoring factory defaults by hardware

In order to restore factory defaults using reset button (RST), please follow the instructions below:

• Unscrew the camera service panel.

• Press the reset button (1) and hold on for 10 seconds.

• Release button

• Screw the camera service panel.

• Log on after 2 minutes using default IP address (http://192.168.1.200) and default user name (root)

and password (pass).

RESTORING FACTORY DEFAULTS

1

Strona jest ładowana ...

AAT NVIP-3SD-6300/30/F (NVIP-3DN3630SD/IRH-2) Instrukcja obsługi

Ten podręcznik jest również odpowiedni dla

AAT NVIP-3SD-6300/30/F (NVIP-3DN3630SD/IRH-2) Instrukcja obsługi

w innych językach

Powiązane dokumenty

Inne dokumenty