Sharp CV-P10PR Instrukcja obsługi

LOCAL AIR CONDITONER

INSTALLATION AND OPERATION

MANUAL

"Plasmacluster" and "Device of a cluster

of grapes" are registered trademarks or

trademarks of Sharp Corporation.

ENGLISH ITALIANO

FRANÇAIS

DEUTSCH ESPAÑOL

PORTUGUÊS

POLSKI

NEDERLANDS

РУССКИЙ

CV-P10PR

CONDIZIONATORE D’ARIA

LOCALE

MANUALE DI INSTALLAZIONE

E FUNZIONAMENTO

KLIMATYZATOR LOKALNY

INSTRUKCJA OBSŁUGI

I INSTALACJI

LOKALE AIRCONDITIONER

INSTALLATIE

EN GEBRUIKERSHANDLEIDING

AR CONDICIONADO LOCAL

MANUAL DE INSTALAÇÃO

E OPERAÇÃO

ACONDICIONADOR DE AIRE

LOCAL

MANUAL DE FUNCIONAMIENTO

E INSTALACCIÓN

LOKALES KLIMAGERÄT

INSTALLATIONS-

UND BEDIENUNGSANLEITUNG

CLIMATISEUR LOCAL

MANUEL D’INSTALLATION

ET D’UTILISATION

ЛОКАЛЬНЫЙ КОНДИЦИОНЕР

ВОЗДУХА

РУКОВОДСТВО ПО МОНТАЖУ

И ЭКСПЛУАТАЦИИ

CV-P10PR_OM_9_lang.indb 1CV-P10PR_OM_9_lang.indb 1 2013-03-20 22:42:022013-03-20 22:42:02

Downloaded from www.Manualslib.com manuals search engine

Attention: Your product is

marked with this symbol. It

means that used electrical and

electronic products should

not be mixed with general

household waste. There is a

separate collection system for

these products.

A. Information on Disposal for Users (private households)

1. In the European Union

Attention: If you want to dispose of this equipment, please do not use the

ordinary dust bin!

Used electrical and electronic equipment must be treated separately and

in accordance with legislation that requires proper treatment, recovery and

recycling of used electrical and electronic equipment.

Following the implementation by member states, private households within

the EU states may return their used electrical and electronic equipment

to designated collection facilities free of charge*. In some countries* your

local retailer may also take back your old product free of charge if you

purchase a similar new one.

*) Please contact your local authority for further details.

If your used electrical or electronic equipment has batteries or

accumulators, please dispose of these separately beforehand according to

local requirements.

By disposing of this product correctly you will help ensure that the waste

undergoes the necessary treatment, recovery and recycling and thus

prevent potential negative effects on the environment and human health

which could otherwise arise due to inappropriate waste handling.

2. In other Countries outside the EU

If you wish to discard this product, please contact your local authorities and

ask for the correct method of disposal.

For Switzerland: Used electrical or electronic equipment can be returned

free of charge to the dealer, even if you don’t purchase a new product.

Further collection facilities are listed on the homepage of www.swico.ch or

www.sens.ch.

B. Information on Disposal for Business Users.

1. In the European Union

If the product is used for business purposes and you want to discard it:

Please contact your SHARP dealer who will inform you about the take-back

of the product. You might be charged for the costs arising from take-back

and recycling. Small products (and small amounts) might be taken back by

your local collection facilities.

For Spain: Please contact the established collection system or your local

authority for take-back of your used products.

2. In other Countries outside the EU

If you wish to discard of this product, please contact your local authorities

and ask for the correct method of disposal.

The battery supplied with this product contains traces of Lead.

For EU: The crossed-out wheeled bin implies that used batteries should

not be put to the general household waste! There is a separate collection

system for used batteries, to allow proper treatment and recycling in

accordance with legislation. Please contact your local authority for details

on the collection and recycling schemes.

For Switzerland: The used battery is to be returned to the selling point.

For other non-EU countries: Please contact your local authority for correct

method of disposal of the used battery.

GB

Contains uorinated greenhouse gases covered by the Kyoto Protocol

R410A (Global warming potential 1975)

Pb

01_CV-P10PR_OM_EN.indd 2 14/08/29 16:42

Downloaded from www.Manualslib.com manuals search engine

GB-1

ENGLISH

Please read this manual carefully before using the product. This manual should be kept in

a safe place for handy reference.

Visit http://sharp-world.com/ for electronic version of the operation manual.

ENGLISH

CONTENTS

• SAFETY PRECAUTIONS ................................................................... GB-2

• INCLUDED ........................................................................................... GB-3

• PART NAMES ...................................................................................... GB-4

• INSTALLATION AND REMOVAL OF EXHAUST HOSE ..................... GB-6

• USING THE REMOTE CONTROL ....................................................... GB-8

• NOTE ON OPERATION ....................................................................... GB-9

USE FOR AIR CONDITIONER

• COOL MODE ....................................................................................... GB-10

• DRY MODE .......................................................................................... GB-10

• FAN MODE .......................................................................................... GB-11

• VENTILATION MODE .......................................................................... GB-11

• TO CHANGE AIR FLOW DIRECTION ................................................. GB-12

• TURBO COOL OPERATION ................................................................ GB-13

• SLEEP OPERATION ............................................................................ GB-13

• TIMER OPERATION ............................................................................ GB-14

USE FOR ION GENERATOR

• ION GENERATOR MODE ................................................................... GB-15

• TO CHANGE AIR FLOW DIRECTION ................................................. GB-16

• MAX DENSITY OPERATION ............................................................... GB-16

• REFRESH OPERATION ...................................................................... GB-17

• OFF TIMER OPERATION .................................................................... GB-17

• MAIN UNIT OPERATION ..................................................................... GB-18

• DRAINAGE .......................................................................................... GB-18

• MAINTENANCE ................................................................................... GB-19

• BEFORE CALLING FOR SERVICE ..................................................... GB-20

01_CV-P10PR_OM_EN.indd 1 14/08/29 16:42

Downloaded from www.Manualslib.com manuals search engine

GB-2

SAFETY PRECAUTIONS

This appliance can be used by children aged from 8 years and above and persons with

reduced physical, sensory or mental capabilities or lack of experience and knowledge if

they have been given supervision or instruction concerning use of the appliance in a safe

way and understand the hazards involved. Children shall not play with the appliance.

Cleaning and user maintenance shall not be made by children without supervision.

WARNINGS

• Do not modify any part of this product. It will cause electric shock, water leak, re etc.

• Do not pull or deform the power supply cord. Pulling and misuse of the power supply cord

can result in damage to the unit and cause electric shock.

• Be careful not to expose your body directly to the outlet air for a long time. It may affect

your physical conditions.

• When using the air conditioner for infants, children, elderly, bedridden, or disabled people

make sure the room temperature is suitable for those in the room.

• Never insert objects into the unit. Inserting objects can result in injury due to the high

speed rotation of internal fans.

• If anything is abnormal with the air conditioner (ex. a burning smell), stop the operation

immediately and disconnect the power plug from the wall socket.

• If the supply cord is damaged, it must be replaced by the manufacturer or its service

agent or a similarly qualied person in order to avoid a hazard. Use only the manufacture-

specied power cord for replacement.

• Do not splash or pour water directly on the unit. Water can cause electric shock or

equipment damage.

• This power plug must only be plugged into an appropriate wall socket. Do not use in con-

junction with any extension cords.

• Push the power plug securely into the socket and make sure it is not loose.

• This appliance must be grounded. This appliance is equipped

with a cord having a grounding wire with a grounding tab.

The plug must be plugged into an outlet that is properly in-

stalled and grounded.

• The appliance shall be installed in accordance with national

wiring regulations.

• The appliance must be positioned so that the plug is accessi-

ble.

CAUTIONS

• Open a window or door periodically to ventilate the room, especially when using gas

appliances. Insufcient ventilation may cause oxygen shortage.

• Do not operate the buttons with wet hand. It may cause electric shock.

• For safety, disconnect the power plug from the wall socket when not using the unit for an

extended period of time.

• This unit is designed for residential use. Do not use for other applications such as in a

kennel or greenhouse to raise animals or grow plants.

• Do not place a vessel with water on the unit. If water penetrates into the unit, electrical

insulations may deteriorate and cause electric shock.

• Drainage should be performed whenever moving the unit. If any water remains in the

tank, it may spill out while being moved.

• Do not block the exhaust air outlet with obstacles. Cooling performance may be reduced

or stop completely.

Plug

Grounding tab

01_CV-P10PR_OM_EN.indd 2 14/08/29 16:42

Downloaded from www.Manualslib.com manuals search engine

GB-3

ENGLISH

30 cm

LOCATION

• The unit should be placed on a rm foundation to

minimize noise and vibration. For safe and secure

positioning, place the unit on a smooth, level oor

strong enough to support the unit. This will also

help to avoid water spilling out into the room

• The unit has casters to aid placement, but it

should only be rolled on smooth, flat surfaces.

Use caution when rolling on carpet surfaces. Do

not attempt to roll the unit over objects.

• The unit must be placed within reach of a properly

rated grounded socket.

• Never place any obstacles around the air inlet or

outlet of the unit.

• Allow at least 30 cm of space from the wall for ef-

cient air-conditioning.

• Be sure to turn the unit off and disconnect the power plug from the wall socket before

performing any maintenance or cleaning. A fan is rotating inside the unit and you may get

injured.

• Place the unit on a level surface to avoid water spilling out into the room.

• Make sure to connect the air conditioner to power supply of the rated voltage and fre-

quency. Use of a power supply with improper voltage and frequency can result in equip-

ment damage and possible re.

• Do not use the unit in a place where inammable gas may leak. It may cause re.

Use the unit in a place with minimal dust, fumes and moisture in the air.

• Make sure a leak breaker or a circuit breaker is installed, depending on the installation

location, to avoid electrical shock.

• Install an earth leakage breaker to avoid electric shock in case of leak.

Use the current-activated, high-sensitivity, high-speed type breaker with a rated sensitivity

current of below 30 mA and an operating time of below 0.1 second.

Exhaust hose

1

Insect guard net

1

Manual

1

Window adapter

1

Remote control

1

Rain guard

2

Battery

(R03)

2

INCLUDED

01_CV-P10PR_OM_EN.indd 3 14/08/29 16:42

Downloaded from www.Manualslib.com manuals search engine

GB-4

1 Air Outlet

2 Vertical louvers

3 Horizontal louvers

4 POWER Button

5 Signal receiver for remote

control

6 AIR CON Lamp (green)

7 TIMER Lamp (orange)

8 MAXIMUM Lamp (red)

9 ION GENERATOR Lamp

(blue)

10 Air inlet

REAR VIEW

NOTE: Actual unit might vary slightly from above illustration.

FRONT VIEW

11 Exhaust air outlet

12

Window adapter

13 Exhaust hose

14 Remote control hook

15 Airlter

16 Grille

17 Air inlet

18 Drainpipe and stopcock

19 Power plug

20 Casters(4)

1

2

3

4

5

6

7

8

9

10

PART NAMES

11

12

13

14

15

16

17

18

19

20

01_CV-P10PR_OM_EN.indd 4 14/08/29 16:42

Downloaded from www.Manualslib.com manuals search engine

GB-5

ENGLISH

REMOTE CONTROL

REMOTE CONTROL DISPLAY

18

19

20

21

22

23

24

25

26

27

12

9

10

11

13

14

15

16

17

1

2

3

4

5

6

7

8

1 Tramsmitter

2 Display

AIR CON MODE ONLY

3 A/C Button

4 TEMP Button

5 TURBO COOL Button

6 MODE Button

7 SLEEP Button

8 TIMER ON Button

ION MODE ONLY

9 ION Button

10 MAX DENSITY Button

11 REFRESH Button

COMMON

12 OFF Button

13 FAN Button

14 SWING Button

15 CANCEL Button

16 TIMER OFF Button

17 RESET Button

18 MODE Symbols

: COOL : DRY

: FAN : VENTILATION

19 REFRESH Symbol

20 TURBO COOL Symbol

21 ION GENERATOR Symbol

22 MAX DENSITY Symbol

23 SLEEP Symbol

24 FAN SPEED Symbols

: AUTO : SOFT

: LOW : HIGH

25 Temperature and timer count

down indicator

26 Transmitting Symbol

27 TIMER ON/TIMER OFF Symbol

01_CV-P10PR_OM_EN.indd 5 14/08/29 16:42

Downloaded from www.Manualslib.com manuals search engine

GB-6

Installation of the exhaust hose

1

Attach the insect guard net to the

window adapter.

Push the insect guard net rmly to en-

sure that four projections on the window

adapter t into the four holes on it.

2

Attach the window adapter to the

exhaust hose.

Extend one end of the exhaust hose and

insert it into the window adapter, and

turn it (approx. three times) until it stops.

Make sure they are securely attached.

3

Attach the rain guards to the in-

sect guard net.

Insert all three projections on each rain

guard into the holes in the insect guard

net.

Side “A” will now be at the top, as indi-

cated in the diagram.

INSTALLATION AND REMOVAL OF EXHAUST HOSE

Exhaust hose

Window adapter

Extend

Hole

Projection

Insect guard net

Rain guard

"A"

Insect guard net

Hole

Projection

Insect guard net

Rain guard

"A"

Horizontally placed

Vertically placed

01_CV-P10PR_OM_EN.indd 6 14/08/29 16:42

Downloaded from www.Manualslib.com manuals search engine

GB-7

ENGLISH

Removal of the exhaust hose

Remove the exhaust hose from the unit.

Lift up and remove the exhaust hose from the

unit by pushing on the two projections.

Projection

The exhaust hose should be as short as possible for operational

efciency;however,itmustnotbetwistedorbent.

Unacceptable

Acceptable

Exhaust hose

Projection

Hole

Exhaust hose

4

Attach the exhaust hose to the

unit.

Insert the two projections into the two

holes on the unit, and rmly attach them

to each other until they click.

5

Lead the exhaust hose outdoors.

01_CV-P10PR_OM_EN.indd 7 14/08/29 16:42

Downloaded from www.Manualslib.com manuals search engine

GB-8

HOW TO USE THE REMOTE CONTROL

Point the remote control toward the Signal re-

ceiver and press the desired button. The unit

generates a beep when it receives the signal.

• Make sure nothing, such as curtains, blocks the

signal receiver window.

• The signal effective distance is 7 m.

CAUTION:

• Do not expose the receiver window to direct sun-

light. This may adversely affect its operation.

• Use of certain uorescent lamp in the same room

may interfere with transmission of the signal.

• Do not leave the remote control in direct sunlight

or near a heater. Protect the remote control from

moisture and shock.

To prevent the remote control from being

misplaced,hookittotheunitwhennotin

use.

When attached, to remove the remote control from

the unit, lift the remote control up slightly and pull it

out.

Remote control hook

LOADING BATTERIES

1

Remove the battery cover.

2

Insert two batteries.

(AAA(R03))

• Make sure the (+) and (-) polarities are cor-

rectly aligned.

• Lines will appear on the display when bat-

teries are properly installed.

3

Reattach the battery cover.

4

Press the RESET button using a thin

pointed implement.

NOTES:

• The battery life is approximately 1 year in normal

use.

• When replacing the batteries, always change

both and use the same type.

• If you will not be using the unit for a long time, re-

move the batteries from the remote control.

Battery cover

USING THE REMOTE CONTROL

01_CV-P10PR_OM_EN.indd 8 14/08/29 16:42

Downloaded from www.Manualslib.com manuals search engine

GB-9

ENGLISH

NOTES ON OPERATION

•Allow3minutesforthecompressortorestartcooling.

If you turn the unit off and immediately restart it, allow three minutes for the compressor

to restart cooling. There is an electronic device in the unit that keeps the compressor

turned off for three minutes for safety.

•Whenpowerfailureoccurs

This air conditioner has a memory function to store settings when a power failure occurs.

After power recovery, the unit will automatically re-start in the same settings which were

active before the power failure, except for timer settings.

If a power failure occurs while the timer is set, the timer setting will be cancelled and will

not be retrieved even after the power is restored.

•Lowtemperatureoperation:Isyourunitfreezingup?

Freezing may occur when the unit is set close to 18°C in low ambient temperature condi-

tions, especially at night.

In these conditions, a further temperature drop may cause the unit to freeze.

Setting the unit to a higher temperature will prevent it from freezing.

•Drymodeincreasesroomtemperature.

The unit generates heat during dry mode and the room temperature will rise. Warm air

will be blown out from the Exhaust air outlet, but this is normal and does not indicate a

problem with the unit.

•Thisunitblowsthewarmairgeneratedbytheunitoutsidetheroomviatheex-

haust hose while in cool mode.

Accordingly, the same amount of air as that is blown out will enter the room from outside

through any openings into the room.

•Whencoolingoperationisperformedathighhumidityconditions,watertankin-

side the unit may frequently become full.

When water tank inside the unit is full, the unit stops operating and the orange TIMER,

the green AIR CON and the red MAXIMUM lamps will blink. In this case, perform

drainage to drain out water within the unit.

OPERATING CONDITIONS

•Theunitmustbeoperatedwithinthefollowingtemperaturerange.

Mode Room temperature

Cool 18°C - 40°C

Dry 15°C - 40°C

• A built-in safety device may cut off operation if the temperature exceeds these limits.

• When cooling operation is performed at high room temperature, the fan may run at a

slower speed.

ENERGY EFFICIENCY TIPS

•Avoiddirectsunlight.

Close blinds, drapes or shades to keep out direct sunlight while in cooling mode.

•Keepthelterclean.

Keeping the lter clean greatly aids efcient operation. A dirty lter blocks the ow of air,

making your unit work harder and less efciently.

NOTE ON OPERATION

01_CV-P10PR_OM_EN.indd 9 14/08/29 16:42

Downloaded from www.Manualslib.com manuals search engine

GB-10

Use when the unit operates with the cool, dry, fan or ventilation mode. During operation,

Plasmacluster ions are always released into the room.

• The exhaust hose must be installed in these modes.

• Ensure that the stopcock is securely attached the drainpipe.

USE FOR AIR CONDITIONER

DRY MODE

1

Press the MODE button to select DRY mode.

COOL DRY FAN VENT

2

Press the A/C button to start operation.

• The green AIR CON lamp will light.

• The temperature cannot be set.

• The fan speed is preset to AUTO and cannot be

changed.

TO TURN OFF

Press the OFF button.

• The green AIR CON lamp will turn off.

NOTES:

• Although you can also operate dry mode without the exhaust hose, the unit generates heat during

operation and the room temperature will rise.

• It is also possible to operate in dry mode with hose (not included) attached.

Remove the stopcock and attach the hose to the drainpipe and lead to a oor drain to allow water to

drain from the unit.

2

1

COOL MODE

1

Press the MODE button to select COOL mode.

COOL DRY FAN VENT

2

Press the A/C button to start operation.

• The green AIR CON lamp will light.

TO TURN OFF

Press the OFF button.

• The green AIR CON lamp will turn off.

3

Press the TEMP button to set temperature.

• The temperature setting range: 18°C to 32°C.

4

Press the FAN button to set fan speed.

AUTO SOFT LOW HIGH

2

3

1

4

01_CV-P10PR_OM_EN.indd 10 14/08/29 16:42

Downloaded from www.Manualslib.com manuals search engine

GB-11

ENGLISH

FAN MODE

The unit simply circulates the air.

1

Press the MODE button to select FAN mode.

COOL DRY FAN VENT

2

Press the A/C button to start operation.

• The green AIR CON lamp will light.

• The temperature cannot be set.

TO TURN OFF

Press the OFF button.

• The green AIR CON lamp will turn off.

3

Press the FAN button to set fan speed.

SOFT LOW HIGH

VENTILATION MODE

The unit ventilates the air to outdoors.

1

Press the MODE button to select VENT mode.

COOL DRY FAN VENT

2

Press the A/C button to start operation.

• The green AIR CON lamp will light.

• The temperature cannot be set.

TO TURN OFF

Press the OFF button.

• The green AIR CON lamp will turn off.

3

Press the FAN button to set fan speed.

• Although the louvers are closed and no air blows

out into the room, the external ventilation fan speed

changes.

SOFT LOW HIGH

2

1

3

2

1

3

01_CV-P10PR_OM_EN.indd 11 14/08/29 16:42

Downloaded from www.Manualslib.com manuals search engine

GB-12

TO CHANGE AIR FLOW DIRECTION

UP / DOWN AIR FLOW DIRECTION

1

Press the SWING button.

• The horizontal louvers will swing.

2

Press the SWING button again to stop the

desired position.

CAUTIONS:

Never attempt to adjust the horizontal louvers manually.

• Manual adjustment of the horizontal louvers can cause the

unit to malfunction when the remote control is used for ad-

justment.

• When the horizontal louvers are positioned at the lowest po-

sition in the COOL or DRY mode for an extended period of

time, condensation may result.

NOTE:

• During VENTILATION mode, UP/DOWN air ow direction

cannot be changed.

LEFT / RIGHT AIR FLOW DIRECTION

Hold the vertical louver as shown in the diagram

and adjust the air ow direction.

CAUTION:

• Do not adjust the vertical louvers to the extreme left or right

in the COOL mode with the fan speed set to "SOFT (

)"

for an extended period of time.

Condensation may form on the louvers.

USE FOR AIR CONDITIONER

1

2

01_CV-P10PR_OM_EN.indd 12 14/08/29 16:42

Downloaded from www.Manualslib.com manuals search engine

GB-13

ENGLISH

TURBO COOL OPERATION

The unit fan works at extra high speed with a setting temperature of 15°C.

1

Press the TURBO COOL button during

cooling mode.

• The remote control will display " ".

• The temperature display will go off.

• The red MAXIMUM lamp will light.

TO CANCEL

Press the TURBO COOL button again.

• The red MAXIMUM lamp will turn off.

NOTES:

• You cannot set the temperature or fan speed during TURBO

COOL operation.

• The fan returns to the HIGH speed setting after the unit has

run for 30 minutes in TURBO COOL mode.

• The extra high fan speed may automatically slow down to protect the unit.

• TURBO COOL operation and SLEEP operation can not be used together.

SLEEP OPERATION

When SLEEP operation is set, the temperature setting is automatically adjusted to prevent

the room from becoming too cold.

1

Press the SLEEP button during cooling

mode.

• The remote control displays “ ”.

• The orange TIMER lamp will light.

• The unit will stop operating after 8 hours.

• The fan speed setting is set to AUTO.

TO CANCEL

Press the SLEEP button.

• The orange TIMER lamp will turn off.

NOTES:

• One hour after the SLEEP operation is started, the tempera-

ture setting rises by 1˚C and after another hour it rises by

an additional 1˚C. Temperature display on the remote control

will not change from its original setting.

• SLEEP operation and TURBO COOL operation can not be

used together.

• The TIMER OFF, TIMER ON and SLEEP operation can not

be set together. Only the most recent settings will be used.

1˚C

8hours

1hour 1hour

Start of SLEEP operation

Unit shuts off

1

01_CV-P10PR_OM_EN.indd 13 14/08/29 16:42

Downloaded from www.Manualslib.com manuals search engine

GB-14

0.5h 1.0h 1.5h 10h 11h 12h

TIMER ON

1

Press the TIMER ON button and set the

time as desired.

• The orange TIMER lamp will light.

• The time setting will count down to show the re-

maining time.

TO CANCEL

Press the CANCEL button.

• The orange TIMER lamp will turn off.

0.5h 1.0h 1.5h 10h 11h 12h

NOTES:

• Timer duration can be set from a minimum of half an hour to a maximum of 12 hours.

Up to 9.5 hours, you can set in half-hour increments and from 10 to 12 hours, in 1-hour increments.

• The TIMER OFF and TIMER ON can not be set together.

• If a power failure occurs while the TIMER OFF or TIMER ON is set, the TIMER setting will be can-

celled and will not be retrieved even after the power is restored.

• When the temperature is set during timer setting, the temperature will show in the display for 5 sec-

onds and then return to the timer display.

TIMER OFF

1

Press the TIMER OFF button and set the

time as desired.

• The orange TIMER lamp will light.

• The time setting will count down to show the re-

maining time.

TO CANCEL

Press the CANCEL button.

• The orange TIMER lamp will turn off.

USE FOR AIR CONDITIONER

CANCEL

1

TIMER OPERATION

1

CANCEL

01_CV-P10PR_OM_EN.indd 14 14/08/29 16:42

Downloaded from www.Manualslib.com manuals search engine

GB-15

ENGLISH

1

Press the ION button to start operation.

• The blue ION GENERATOR lamp will light.

TO TURN OFF

Press the OFF button.

• The blue ION GENERATOR lamp will turn off.

2

Press the FAN button to set fan speed.

SOFT LOW HIGH

USE FOR ION GENERATOR

Use when the unit operates with ION GENERATOR independently.

There is no need to install the exhaust hose. Hot air will not come out from the exhaust

hose during ION GENERATOR mode.

1

2

ION GENERATOR MODE

Note for ION GENERATOR MODE

The ion generator inside the unit releases Plasmacluster ions into the room. Plasmacluster

ions will reduce airborne mold.

Plasmacluster is SHARP’s original technology.

For more information, please check our press release such as:

http://www.sharp-pci.com/

The website is subject to change without notice.

01_CV-P10PR_OM_EN.indd 15 14/08/29 16:42

Downloaded from www.Manualslib.com manuals search engine

GB-16

MAX DENSITY OPERATION

The unit releases max density Plasmacluster ions. By continuously discharging “extra high”

airow for 30 minutes, the unit discharges the ions throughout the room more effectively.

1

Press the MAX DENSITY button during Ion

generator operation.

• The remote control will display " ".

• The red MAXIMUM lamp will light.

TO CANCEL

Press the MAX DENSITY button again.

• The red MAXIMUM lamp will turn off.

NOTES:

• You cannot set the fan speed during MAX DENSITY opera-

tion.

• The MAX DENSITY operation will be automatically can-

celled in 30 minutes, and the unit will return to the original

settings.

• MAX DENSITY operation and REFRESH operation can not

be used together.

USE FOR ION GENERATOR

TO CHANGE AIR FLOW DIRECTION

UP / DOWN AIR FLOW DIRECTION

1

Press the SWING button.

• The horizontal louvers will swing.

2

Press the SWING button again to stop the

desired position.

CAUTION:

Never attempt to adjust the horizontal louvers manually.

• Manual adjustment of the horizontal louvers can cause the

unit to malfunction when the remote control is used for ad-

justment.

LEFT / RIGHT AIR FLOW DIRECTION

Hold the vertical louver as shown in the diagram

and adjust the air ow direction.

1

2

1

01_CV-P10PR_OM_EN.indd 16 14/08/29 16:42

Downloaded from www.Manualslib.com manuals search engine

GB-17

ENGLISH

REFRESH OPERATION

REFRESH operation will reduce odors of clothes with Plasmacluster ions. It is recommend-

ed to use this function in front of the wardrobe, closet, laundry room or hanging cloth.

1

Press the REFRESH button during Ion

generator operation.

• The orange TIMER lamp will light.

• The remote control will display " ".

• The horizontal louvers will swing.

• The unit will stop operating after 5 hours.

TO CANCEL

Press the REFRESH button again.

• The orange TIMER lamp will turn off.

NOTES:

• Adjust the louvers so that air from the unit is blown to the

clothes.

• REFRESH operation and MAX DENSITY operation can not

be used together.

• REFRESH operation and TIMER OFF can not be set together.

• With this operation, Plasmacluster ion is effective for reducing smell of tobacco smoke etc., but may

not always be effective for every kinds of odor.

• Depending on the volume of odor, distance between this unit and clothes, and operating time, this

unit may not reduce the odor enough.

TIMER OFF OPERATION

1

Press the TIMER OFF button and set the

time as desired.

• The orange TIMER lamp will light.

• The time setting will count down to show the re-

maining time.

TO CANCEL

Press the CANCEL button.

• The orange TIMER lamp will turn off.

NOTES:

• Timer duration can be set from a minimum of half an hour to a

maximum of 12 hours.

Up to 9.5 hours, you can set in half-hour increments and from

10 to 12 hours, in 1-hour increments.

• In ION GENERATOR mode, TIMER ON can not be set.

• If a power failure occurs while the TIMER OFF is set, the

TIMER setting will be cancelled and will not be retrieved even

after the power is restored.

0.5h 1.0h 1.5h 10h 11h 12h

1

CANCEL

01_CV-P10PR_OM_EN.indd 17 14/08/29 16:42

Downloaded from www.Manualslib.com manuals search engine

GB-18

Drain out water within the unit in the following cases.

• When the unit stops operating and the orange TIMER lamp, the green AIR CON lamp

and the red MAXIMUM lamp are blinking, the water tank is full and need to be drained.

• When the unit is not used for a long time.

1

Unplug the power plug and carefully move

the unit to a drain or outside to avoid wa-

ter spilling out into the room.

2

Removethestopcockfromthedrainpipe,

and drain water within the unit.

3

Attach the stopcock securely to the drain-

pipe.

MAIN UNIT OPERATION

1

Press the POWER button to start opera-

tion.

• The mode will change as you press the button

within 5 seconds.

• In cool mode, the unit will operate at its last

cooling settings. If the unit has been unplugged

since it was last operated, it will resume opera-

tion in the cooling mode, set at 20˚C. The fan

speed set to AUTO.

TO TURN OFF

Press the POWER button during opera-

tion.

Stopcock

Drainpipe

DRAINAGE

Use this operation when the remote control is not available.

COOL

(The green AIR CON lamp will light)

ION GENERTOR

(The blue ION GENERATOR lamp will light)

OFF

01_CV-P10PR_OM_EN.indd 18 14/08/29 16:42

Downloaded from www.Manualslib.com manuals search engine

Strona jest ładowana ...

Sharp CV-P10PR Instrukcja obsługi

Sharp CV-P10PR Instrukcja obsługi

w innych językach

Powiązane dokumenty

Inne dokumenty