AAT NVR-4116-H1 Instrukcja obsługi

User’s ma n ua l

(s h o rt )

NVR-4204P4-H1

NVR-4308P8-H1

NVR-4116-H1

2

NVR-4204P4-H1, NVR-4308P8-H1, NVR-4116-H1 User’s manual (short) ver.1.3

INFORMACJE

IMPORTANT SAFEGUARDS AND WARNINGS

EMC (2014/30/EC) and LVD (2014/35/EC) Directives

CE Marking

Our products are manufactured to comply with requirements of following directives and

national regulations implementing the directives:

• Electromagnetic compatibility EMC 2014/30/EC.

• Low voltage LVD 2014/35/EC with further amendment. The Directive applies to electrical

equipment designed for use with a voltage rating of between 50VAC and 1000VAC as well

as 75VDC and 1500VDC.

WEEE Directive 2012/19/EC

Information on Disposal for Users of Waste Electrical and Electronic Equipment

This appliance is marked according to the European Directive on Waste Electrical and

Electronic Equipment (2012/19/EC) and further amendments. By ensuring this product is

disposed of correctly, you will help to prevent potential negative consequences for the environment and

human health, which could otherwise be caused by inappropriate waste handling of this product.

The symbol on the product, or the documents accompanying the product, indicates that this appliance

may not be treated as household waste. It shall be handed over to the applicable collection point for the

waste electrical and electronic equipment for recycling purpose. For more information about recycling

of this product, please contact your local authorities, your household waste disposal service or the shop

where you purchased the product.

RoHS Directive 2011/65/EC

Concerning for human health protection and friendly environment, we assure that our

products falling under RoHS Directive regulations, regarding the restriction of the use of

hazardous substances in electrical and electronic equipment, were designed and

manufactured in compliance with mentioned regulation. Simultaneously, we claim that our

products were tested and do not contain hazardous substances exceeding limits which could

have negative impact on human health or natural environment.

Information

The device, as a part of professional CCTV system used for surveillance and control, is not designed

for self installation in households by individuals without technical knowledge.

The manufacturer is not responsible for defects and damages resulted from improper or inconsistent

with user’s manual installation of the device in the system.

NVR-4204P4-H1, NVR-4308P8-H1, NVR-4116-H1 User’s manual (short) ver.1.3

3

SAFETY REQUIREMENTS

ATTENTION!

PRIOR TO UNDERTAKING ANY ACTION THAT IS NOT PROVISIONED FOR THE

PRODUCT IN ITS USER’S MANUAL AVAILABLE AT WWW.NOVUSCCTV.COM AND

OTHER DOCUMENTS DELIVERED WITH THE PRODUCT, OR THAT ARISES FROM

THE NORMAL APPLICATION OF THE PRODUCT, ITS MANUFACTURER MUST BE

CONTACTED OR THE RESPONSIBILITY OF THE MANUFACTURER FOR THE

RESULTS OF SUCH AN ACTION SHELL BE EXCLUDED.

1. Prior to undertaking any action please consult the following manual and read all the safety and

operating instructions before starting the device.

2. Please keep this manual for the lifespan of the device in case referring to the contents of this manual

is necessary;

3. All the safety precautions referred to in this manual should be strictly followed, as they have a direct

influence on user’s safety and durability and reliability of the device;

4. All actions conducted by the servicemen and users must be accomplished in accordance with the

user’s manual;

5. The device should be disconnected from power sources during maintenance procedures;

6. Usage of additional devices and components neither provided nor recommended by the producer is

forbidden;

7. You are not allowed to use the device in high humidity environment (i.e. close to swimming pools,

bath tubs, damp basements);

8. Mounting the device in places where proper ventilation cannot be provided (e. g. closed lockers etc.)

is not recommended since it may lead to heat build-up and damaging the device itself as a

consequence;

9. Mounting the device on unstable surface or using not recommended mounts is forbidden.

Improperly mounted device may cause a fatal accident or may be seriously damaged itself. The

device must be mounted by qualified personnel with proper authorization, in accordance with this

user’s manual.

10. Device should be supplied only from a power sources whose parameters are in accordance with

those specified by the producer in the devices technical datasheet. Therefore, it is forbidden to

supply the devices from a power sources with unknown parameters, unstable or not meeting

producer’s requirements;

11. You cannot allow any metal objects get inside the recorder. It might cause serious damage. If a

metal object gets inside the device contact the authorised Novus service immediately.

12. The manufacturer does not bear responsibility for damage or loss of data stored on HDDs or other

media occurred during the usage of the product.

Due to the product being constantly enhanced and optimized, certain parameters and functions

described in the manual in question may change without further notice.

We strongly suggest visiting the www.novuscctv.com website in order to access the newest

manual .

NOVUS NVRs are dedicated to work with NOVUS cameras. Using only NOVUS products

guarantees the highest image quality. Connecting cameras from other manufacturers to NOVUS

NVRs may decrease video quality.

The manufacturer reserves the right to printing errors and technical changes without prior

notice.

4

NVR-4204P4-H1, NVR-4308P8-H1, NVR-4116-H1 User’s manual (short) ver.1.3

FOREWORD INFORMATION

1. FOREWORD INFORMATION

1. 1. Main characteristics

• Network Video Recorders.

• Recording resolution up to 3840 x 2160.

• H.264, H.265 compression.

• Dual stream recording.

• Support 1 x SATA 3,5” HDD.*

• E-SATA connector for external HDD matrix NV-5000EST-H4 (supports up to 4 x HDD 3.5”

SATA).**

• Operating system based on Linux.

• Main monitor 1 x HDMI (4K UltraHD), 1 x VGA (FullHD).

• Support fisheye cameras.**

• Ethernet PoE ports.

• Intelligent video analysis.

• Backup: onto HDD or USB Flash Memory through USB port & through the network.

• Software: NHDR-5000 Viewer (application for remote administration, live monitoring and recorded

data search ).

• User friendly multi-lingual OSD.

• IR remote control and PC mouse control (in-set included).

* The list of recommended disk models and their capacity is available on Novus Security website in

the Compatible Disk file in the product “Downloadable files” tab.

** Function depends on the model.

NVR-4204P4-H1, NVR-4308P8-H1, NVR-4116-H1 User’s manual (short) ver.1.3

5

1.2. Technical data

*** with dual streaming mode.

FOREWORD INFORMATION

NVR-4204P4-H1 NVR-4308P8-H1

NVR-4116-H1

Video

IP Cameras

4 channels at 3840 x 2160

resolution (video + audio)

8 channels at 3840 x 2160

resolution (video + audio)

16 channels at 3840 x 2160

resolution (video + audio)

Supported Resolution

max. 3840 x 2160

max. 2160 x 2160 for fisheye cameras

max. 3840 x 2160

Compression H.264, H.265

Monitor Output

main (split screen, full screen, sequence): 1 x VGA, 1 x HDMI (4K UltraHD) (up to 2

monitors simultaneously)

Dualstreaming Support yes

Fisheye support

yes, 2000/4000 IP series cameras -

Audio

Audio Output 1 x line-out (RCA), 1 x HDMI

Recording

Recording Speed

120 fps (4 x 30 fps for 3840

x 2160 and lower)

240 fps (8 x 30 fps for 3840

x 2160 and lower)

480 fps (16 x 30 fps for 3840 x

2160 and lower)

Stream Size

40 Mb/s in total from all

cameras

128 Mb/s in total from all

cameras

100 Mb/s in total from all

cameras

Recording Mode

time-lapse, triggered by: manual, alarm input, motion detection, intelligent image analysis

functions, PIR alarm

Prealarm/Postalarm up to 3 s/up to 600 s

Display

Display Speed 120 fps (4 x 30 fps)*** 240 fps (8 x 30 fps)*** 480 fps (16 x 30 fps)***

Playback

Playback Speed 120 fps (4 x 30 fps) *** 240 fps (8 x 30 fps) *** 240 fps (16 x 30 fps) ***

Recorded Data Search by date/time, events, image analysis events, motion in a defined area, tags

Backup

Backup Methods DVD (option), USB port (HDD or Flash memory), network

Backup File Format

JPG, BMP, PNG, MP4, AVI, RF

Storage

Internal storage available mount: 1 x HDD 3.5” 10 TB SATA *

Total Internal Capacity 10 TB

External storage 1 x eSATA -

Total External Capacity - 24 TB

Alarm

Internal Alarm Input/Output 4/1 relay type 8/1 relay type -

System Reaction to Alarm

Events

buzzer, e-mail, alarm output activation, screen message,

recording activation, PTZ, Full Screen, picture to Cloud,

video to Cloud

buzzer, e-mail, alarm output

activation, screen message,

recording activation, PTZ, Full

Screen, FTP picture upload, FTP

video upload, picture to Cloud,

video to Cloud

Intelligent image analysis

Supported functions

Exception, Tripwire, Zone entrance, Abandoned Object, Object Disappearance, Face

Detection, Pedestrian Detection, Cross Counting, Sound detection

6

NVR-4204P4-H1, NVR-4308P8-H1, NVR-4116-H1 User’s manual (short) ver.1.3

FOREWORD INFORMATION

1.3. Package contents

Unpack the device carefully. After unpacking, ensure that package contains the following items:

• Network Video Recorder.

• Power supply 100 ~ 240 VAC/12 VDC PSU or 100 ~ 240 VAC/48 VDC PSU.

• Power cord.

• USB Mouse.

• IR remote controller.

• User’s manual (short).

If any of the elements has been damaged during transport, pack all the elements back into the original

packaging and contact your supplier.

NVR-4204P4-H1 NVR-4308P8-H1

NVR-4116-H1

Network

Network Interface

1 x Ethernet - RJ-45

interface, 10/100 Mbit/s

4 x Ethernet PoE - RJ-45

interface, 10/100 Mbit/s

with Extended mode

1 x Ethernet - RJ-45

interface, 10/100/1000 Mbit/s

8 x Ethernet PoE - RJ-45

interface, 10/100 Mbit/s with

Extended mode

1 x Ethernet - RJ-45 interface,

10/100/1000 Mbit/s

Network Protocols Support

HTTP, TCP/IP, IPv4, HTTPS,

FTP, DHCP, DNS, DDNS, NTP,

RTSP, UPnP, SNMP, SMTP

HTTP, TCP/IP, IPv4, HTTPS, DHCP, DNS, DDNS, NTP,

RTSP, UPnP, SNMP, SMTP

PC/MAC Software Internet Explorer, NHDR-5000 Viewer/NHDR-5000 Viewer

Smartphone Software RxCamView (iPhone, Android)

Max. Number of Connections

with NVR

40 40 40

Bandwidth

40 Mb/s in total to all client

workstations

128 Mb/s in total to all client

workstations

64 Mb/s in total to all client

workstations

PTZ

PTZ Functions pan/tilt/zoom, preset commands, patterns

Auxiliary Interfaces

USB Ports 3 x USB 2.0 2 x USB 3.0, 1 x USB 2.0 2 x USB 2.0

Operating system

Operating System Linux

OSD languages: Polish, English, others

Control PC mouse and IR remote controller (in-set included), network

System Diagnostic automatic control of: HDDs, network, camera connection loss

Security password protection, IP filtering

Installation parameters

Dimensions (mm) 300 (W) x 53 (H) x 227 (D)

Weight 1.1 kg (without HDD)

Power Supply

48 VDC (100 ~ 240

VAC/48 VDC PSU in-set

included)

48 VDC (100 ~ 240 VAC/48

VDC PSU in-set included)

12 VDC (100 ~ 240 VAC/12

VDC PSU in-set included)

Power Consumption

20 W (with 1 HDD) +

120 W PoE

20 W (with 1 HDD) +

240 W PoE

20 W (with 1 HDD)

Operating Temperature -10°C ~ 45°C

NVR-4204P4-H1, NVR-4308P8-H1, NVR-4116-H1 User’s manual (short) ver.1.3

7

2. STARTING THE DEVICE

2.1. Electrical connection and other rear panel elements.

NVR-4204P4-H1

NVR-4308P8-H1

NVR-4116-H1

STARTING THE DEVICE

5

12

7

8

10

2

9

13

7

8

4

5

1

9

10

11

2

6

3

7

8

4

5

1

9

10

11

2

6

3

8

NVR-4204P4-H1, NVR-4308P8-H1, NVR-4116-H1 User’s manual (short) ver.1.3

1. POWER DC: Power supply connector for 48V adapter.

2. POWER SW: Power switch.

3. ALARM IN: Alarm input terminal.

4. ALARM OUT: Alarm output, relay.

5. AUDIO OUT: Audio output for connecting speakers and amplifier (RCA connector).

6. AUDIO IN: Audio mono inputs (RCA LINE IN type) for connecting microphone. Allows

intercom connection between the recorder and the client station. The connection

is initiated from the client software or browser. Sound is not recorded.

7. VGA: VGA main monitor connector, use the D-SUB VGA cable to connect monitor.

8. HDMI: HDMI main monitor connector, use the HDMI cable to connect monitor.

9. USB: USB port for external Flash memory, mouse connection and other USB

compatible devices.

10. WAN: RJ-45 ethernet port for connecting to the local network.

11. POE LAN: RJ-45 ethernet ports for connecting PoE cameras.

12. E-SATA: E-SATA connector for NV-5000EST-H4 HDD matrix.

13. POWER DC: Power supply connector for 12V adapter.

2.2. Hard drive mounting

Note:

In order to obtain info on latest compatible HDDs together with their capacities, please contact

your distributor or visit www.novuscctv.com website. AAT HOLDING S.A. company does not

bear responsibility for any issues arising from usage of unsupported SD cards/HDDs.

List of compatible HDDs contains all disks supported by NVR model, including desktop HDDs.

However due to the fact that image recording prefers reliability usage of 24x7 recording HDDs is

therefore advised.

If a disk was used in another device, it is necessary to format it. Please take it into account due to

the irrecoverable data loss resulting from said process.

NVRs support 1 x 3,5" SATA HDD. Follow the instruction to mount the HDD. Photos are illustrative,

may differ slightly from the described recorder.

Before staring the process make sure the power supply is not connected.

STARTING THE DEVICE

NVR-4204P4-H1, NVR-4308P8-H1, NVR-4116-H1 User’s manual (short) ver.1.3

9

In order to mount HDD, unscrew 5 screws on the back and both sides as depicted below and remove

top cover.

Mounting place is highlighted below. Put the HDD in the place.

STARTING THE DEVICE

HDD

10

NVR-4204P4-H1, NVR-4308P8-H1, NVR-4116-H1 User’s manual (short) ver.1.3

Turn the NVR aside holding HDD. Screw it tightly to the bottom.

Connect SATA and power cable to HDD. Install the top cover on the NVR and screw it back.

STARTING THE DEVICE

HDD

NVR-4204P4-H1, NVR-4308P8-H1, NVR-4116-H1 User’s manual (short) ver.1.3

11

2.3. Connecting the power supply

Before starting the device, connect the supplied DC adapter to the power socket located on the rear

panel of the recorder.

To start the device turn on the power switch on the back panel. Initialization lasts about 60 seconds.

During this time executing any device functions and pressing any buttons is prohibited. To shut down

the device please use the menu.

CAUTION:

Make connection when the power is not applied and the power switch is turned off. Do not

modify the connection of power supplies and their grounding.

In order to ensure uninterrupted operation of the device, make sure that all connections are

made correctly and permanently, preventing their accidental disconnection.

If the device was brought from a room with a lower temperature, wait until it reaches the

temperature of the room in which it is to work. Do not turn on the device immediately after

bringing it from a cooler place. Condensation of water vapor in the air may cause short circuits

and, consequently, damage the device.

Before starting the device familiarize yourself with the description and the role of the individual

inputs and outputs located on the rear panel and adjusting elements that the device is equipped

with.

2.4. Connecting monitor

NVRs support following interfaces for main monitor: HDMI, VGA.

HDMI interface support the following resolutions: 1024x768, 1280x1024, 1440x900, 1280x720,

1920x1080, 2560x1440, 3840x2160. VGA interface supports resolution up to 1920x1080.

2.5. Connecting ethernet and IP cameras

It is recommend to configure the camera before connecting to the recorder, as described in the user

manual of the camera. Please note that the cameras should be addressed with the unique IP address

from the range supported by the recorder.

NVR-4204P4-H1 and NVR-4308P8-H1 recorders have built-in RJ-45 PoE ports, which allow to

connect PoE powered cameras directly to the recorder. The maximum cable length from the recorder

to each camera is 100m. In Extended PoE (EPOE) mode, data transmission speed is reduced to

10Mbps, cable length can be up to 200m. EPOE mode can be turned on for selected cameras.

NVRs with built-in PoE ports use different addressing for PoE ports, different for connecting to the

router through the WAN port.

By connecting a NOVUS 2000 or 4000 series IP camera to the PoE port, the camera will be

automatically added to the list if the camera has a default password.

STARTING THE DEVICE

12

NVR-4204P4-H1, NVR-4308P8-H1, NVR-4116-H1 User’s manual (short) ver.1.3

Connecting IP cameras and ethernet to NVR-4204P4-H1 (alike NVR-4308P8-H1)

Connecting IP cameras and ethernet to NVR-4116-H1

STARTING THE DEVICE

NVR-4116-H1

INTERNET

PC

ROUTER

POE IP CAMERA

INTERNET

PC

ROUTER

IP CAMERA

NVR-4204P4-H1

NVR-4204P4-H1, NVR-4308P8-H1, NVR-4116-H1 User’s manual (short) ver.1.3

13

2.6. Security recommendations for network architecture and configuration

WARNING!

Below are shown security recommendations for network architecture and configuration

of CCTV systems that are connected to the Internet to reduce the risk

of unauthorized interference with the system by a third party.

1. Absolutely change the default passwords and user names (if the device gives this possibility) of

all applied network devices (recorders, cameras, routers, network switches, etc.) to the

severely complexity password. Use lowercase and uppercase letters, numbers, and special characters

if there is such possibility.

2. Depending on the available functionality in the order to restrict access to the used network devices at

the administrator account level, it is recommended to configure the users accounts accordingly.

3. Do not use DMZ function (Demilitarized zone) in your router. Using that function you open the

access to recorder system from the Internet on all ports, which gives possibility for an unauthorized

interference with the system.

Instead of DMZ use port forwarding redirect only the ports which are necessary for the performance

of the connection (detailed information about ports of communication in different models of recorders,

cameras, etc. can be found in the operating instructions).

4. Use routers with firewall function and make sure it is enabled and properly configured.

5. It is recommended to change the default network communication port numbers of used devices

if there is such possibility.

6. If used network devices has a UPnP feature and it is not used, turn it off.

7. If used network devices has a P2P feature and it is not used, turn it off.

8. If used network devices support HTTPS protocol for connection, it is recommended to use it.

9. If used network devices support IP filtering for authorized connections function, it is recommended

to use it.

10. If used recorder has two network interfaces it is recommended to use both of them to physically

separate network for cameras and network for Internet connection. The only device in the system,

accessible from Internet is recorder - there is no physically access directly to any camera.

STARTING THE DEVICE

14

NVR-4204P4-H1, NVR-4308P8-H1, NVR-4116-H1 User’s manual (short) ver.1.3

2.7. Connecting alarm inputs / output

NVR-4204P4-H1 and NVR-4308P8-H1 have alarm inputs and output. Alarm terminal is shown below.

Alarm inputs, may be set either as normal open (N.O.) or normal closed (N.C.) Check the NVR menu

settings (chapter “Alarm section” in user’s manual). The ground of the alarm device needs to be

connected to one of the G connectors. Detailed information on alarm configuration can be found in the

chapter "Alarms" in the user manual.

Alarm output is a relay with 2 connectors (ALARM connectors on terminal). Max contact ratings are

3A 250VAC / 3A 30VDC.

2.8. Front panel elements

1. IR receiver.

2. Power LED (red). When the LED is light on, it means NVR is working.

3. HDD LED (green). Flickering indicates the recording or playback is in progress.

4. USB port for external HDDs, Flash memory or USB mouse connection.

STARTING THE DEVICE

NVR-4308P8-H1

8 7 6 5 G 4 3 2 1 G ALARM ALARM

Alarm Inputs Alarm Output

NVR-4204P4-H1

4 3 2 1 G ALARM ALARM

Alarm Inputs Alarm Output

1 2 3 4

NVR-4204P4-H1, NVR-4308P8-H1, NVR-4116-H1 User’s manual (short) ver.1.3

15

3. NVR OPERATING

3.1. Control

Recorders can be controlled using IR remote controller or USB mouse.

3.1.1. Controlling via IR remote controller

IR remote controller is included with NVR. IR range depends on battery status and may vary between a

few and several meters.

Controller is supplied with two AAA batteries. Buttons functions are listed below.

3.1.2. Controlling via USB mouse

It is possible to control NVR functions using an USB mouse. Double-clicking on any camera in

division mode (e.g. 2x2, 3x3, etc.) switches the display to full-screen mode. Another double-click

returns to previous display mode. Move cursor to the bottom of the screen to display menu bar. Press

left mouse button on the channel video to display channel menu. Certain positions allow to select them

via mouse scroll. Depending on NVR operating mode, right mouse button leaves menu.

NVR OPERATING

0 - 9

Numeric buttons for channel selection. Channel 10 and another

can be selected using buttons combination. i.e. to open channel

15 press „1” and then „5”.

ALL

Toggles between different display formats: 1, 4, 9, etc.

MENU

Enters to main menu. Pressing this button cancel the selection

and leaving the menu also.

SUBMENU

In live mode open the Popup menu.

Navigation control „left”, „right”. In live mode open the Popup

menu.

Navigation control „up” , „down”.

SEL

Button is used for confirm the selection and start to editing

fields. In live mode open the Popup menu.

Switch on playback mode. Open Record Search menu. In live

mode open the Popup menu.

Slow down playback speed.

Fast up playback speed.

Turn on manual record.

Playback pause, press again to play frame by frame.

Stop the playback. In live mode stop the manual recording.

16

NVR-4204P4-H1, NVR-4308P8-H1, NVR-4116-H1 User’s manual (short) ver.1.3

NVR OPERATING

3.2. First Launch Wizard

3.2.1. Language selection and creating password

To start the unit connect the power cable to DC adapter, turn on the power switch on back panel and

wait for initialization. It lasts for approximately 60 seconds. During this time executing any device

functions and pressing any buttons is prohibited. After first launch NVR displays window as below. It

allows to change the language. Select the desired one from the Language list.

Default language is English. If you change the language, all the descriptions will be translated

automatically.

Click on the field to expand list or display virtual keyboard.

New Admin Name - name of administrator account (default: admin).

Password Strenght - the scale showing how strong is the written password. It is updated on the fly

while typing the password in the next fiels. Password strenght can be Low, Medium or High and

marked with Red, Yellow or Green color.

New Admin Password - it is required to create access password. It must contain 5-15 characters.

Confirm password - enter the access password again to confirm.

Show Password - shows password instead of masking marks.

Unlock Pattern Enable - enables an alternative authentication method for the password using the

pattern. It allows to enter administrative settings and make changes. Some settings, such as disk

formatting, import/export settings still require password authentication.

Draw - the function shows when Unlock Pattern function is enabled. It allows to create an unlock

pattern. There is 3x3 board to create a pattern by dragging the mouse cursor. The pattern has to be

confirmed by dragging the mouse cursor again.

Apply - saves settings.

NVR-4204P4-H1, NVR-4308P8-H1, NVR-4116-H1 User’s manual (short) ver.1.3

17

NVR OPERATING

The next step is to log in using the created user data.

The Password button switch to login window using defined password.

The Pattern window switch back to previous window.

After authentication the First Launch Wizard opens.

18

NVR-4204P4-H1, NVR-4308P8-H1, NVR-4116-H1 User’s manual (short) ver.1.3

NVR OPERATING

3.3. Frist Launch Wizard

The first launch wizard provides a quick way to configure basic NVR settings.

When the Start Wizard will be pressed, subsequent sections of the wizard will appear.

The Next and Previous buttons allow to toggle between consecutive sections. The Cancel button exits

the wizard without saving any changes.

3.3.1. Network Settings

NVR-4204P4-H1, NVR-4308P8-H1, NVR-4116-H1 User’s manual (short) ver.1.3

19

NVR OPERATING

This section contains basic network settings:

DHCP - enable network settings retrieval from a DHCP server.

IP Address - network address of the recorder in the local network.

Subnet Mask - number dividing in IP address the network part.

Gateway - IP address of the router for Internet connection.

DNS1 - domain server address.

DNS2 - alternative domain server address.

Web Port- the port used to connect with the NVR network plugin by Internet Explorer browser.

Client Port - the port used to connect with the NVR by NHDR-5000Viewer, NMS, RxCamView.

RTSP Port - the port used for RTSP streaming from NVR..

HTTPS - the port used while the connection with HTTPS protocol.

UPNP - enable the UPnP discovery feature. The UPnP function must be supported by the router.

UPNP Status - informs if the UPnP function is active for the port (Active or Inactive).

Caution! NVR-4116-H1 cannot be assigned a network address 10.10.xxx.xxx

3.3.2. Time and date settings

This section contains all the date and time options in the recorder.

Date - select day from calandar.

Time - current NVR time. It can be written manually.

Date Format - dispaly format of the date (MM/DD/YY, YY-MM-DD, DD/MM/YY).

Time Format - display format of time (12 Hour or 24 Hour).

Time Zone - display a time zone depending on the region.

20

NVR-4204P4-H1, NVR-4308P8-H1, NVR-4116-H1 User’s manual (short) ver.1.3

NVR OPERATING

The recorder allows to synchronize time with the NTP server. The NTP server can be selected from

drop-down list. The User-Deifined option allows to enter any IP address of the time server.

The correct network settings and connection are required to allow communication with the NTP server.

The recorder allows to set daylight saving time.

Time Offset - defines time advancing (1Hour, 2Hour).

DST Mode - defines method of switching by specified Week, or by specified Day.

Start Time - defines first day of DST.

End Time - defines last day of DST.

3.3.3. Adding IP cameras

The section allows for adding IP cameras to the NVR. All channels of NVR-4204P4-H1 and NVR-

4308P8-H1 recorders are in automatic PoE mode by default. It means that connecting Novus 2000 or

4000 series IP camera to PoE port add it automatically to the list (camera has to have default

password).

Caution! Automatic PoE mode supports only Novus 2000 and 4000 series IP cameras.

Strona jest ładowana ...

AAT NVR-4116-H1 Instrukcja obsługi

Ten podręcznik jest również odpowiedni dla

AAT NVR-4116-H1 Instrukcja obsługi

w innych językach

Powiązane dokumenty

Inne dokumenty