ELEKTRA ELR-10 Instrukcja instalacji

www.elektra.eu

electronic

temperature controller

RU

Instrukcja montażu PL

Installation manual UK

Инструкция по монтажу

Congratulations on purchasing

the ELEKTRA ELR-10 electronic

temperature controller. Thank

you for the trust you have

placed in our company. The

controller will be of use to

your family for many years to

come. It can significantly

reduce your energy expenses,

and will improve your thermal

comfort.

Please read this manual carefully before

operating the controller.

ELEKTRA ELR-10

2

3

TABLE OF CONTENTS

1. Introduction

2. Classification

3. Installing the floor sensor

4. Installing the controller with built-in air sensor

5. Installing the controller with built-in air

and additional sensor limiting floor temperature

to +40°C

6. Technical specifications

7. Installing the controller

8. Switching the controller on and its adjustments

9. Warranty conditions

1. INTRODUCTION

The ELEKTRA ELR-10 electronic temperature controller

manages the supply of power to heating elements so

that the required (optimal) temperature can be

acquired, thus ensuring reduced electricity

consumption.

ELEKTRA ELR-10 uses the three following temperature

measurement methods:

- air sensor,

- floor sensor,

- air and floor sensors.

4

Depending on the temperature measurement method

used, prepare the controller in advance by installing

the jumper across the correct pins. The controller

preparation procedure is shown in the table below:

Tab. 1. Preparing the controller depending on the

temperature measurement method.

Temperature

measurement

method

Preparing

the controller

connectors C-D closed;

the controller uses the

built-in air temperature

sensor.

air sensor

1

5

Temperature

measurement

method

Preparing

the controller

remove the C-D jumper;

connect the floor sensor to

the A-D connector

floor

sensor

2

connectors C-D closed;

the controller uses

the built-in air temperature

sensor. Connect the floor

sensor to connectors A-B

air sensor

with floor

temperature

limited

to +40°C

3

6

NOTE: Electricity supply must be isolated while

installing the controller!

A B

C

D

1

jumper

A B C D

2

floor

sensor

A B C D

3

jumper

floor

sensor

Fig.1 Install the jumper for the preferred method of

temperature measurement.

7

2. CLASSIFICATION

The product complies with the 2nd protection class

(reinforced insulation) and has to be wired in the

following manner:

connector N: neutral wire

connector L: phase wire

connectors N, L1: heating device (max. 3600W)

N N

L1

L

Heating device

max. 3600 W

230V/50Hz

Fig 2. Connection diagram

for the heating device and

controller power supply.

Heating device max. 3600 W

230V 50Hz

8

3. INSTALLING

THE FLOOR SENSOR

The floor sensor must be installed in a blanked off

conduit (e.g. a flexible PVC pipe) which should be

positioned in the floor screed of the concrete floor,

between heating cables. The sensor wire can be

extended up to 50m in length.

9

Plaster box

Temperature controller

Temperature

sensor

(even

distance

between

heating

cables)

Plug

Floor

Heating mat

Tile cement

Protection pipe (e.g. PVC)

Insulation

Base floor

Sand-concrete

mortar with

floor screed

Temperature sensor cable

Fig. 3. Installing the floor temperature sensor with

ELEKTRA heating mats used.

10

4. INSTALLING THE CONTROLLER

WITH BUILT-IN AIR SENSOR

The controller should be positioned in a draught-free

location and cannot be exposed to direct sunlight or

another source of heat, which could disturb proper

temperature measurements. The sensor should be

installed between 1.2m and 1.6m above floor level.

11

120-160 cm

Fig. 4. Proper location for the controller.

12

5. INSTALLING THE CONTROLLER

WITH BUILT-IN AIR

OR FLOOR SENSOR AND ADDITIONAL

SENSOR LIMITING FLOOR

TEMPERATURE TO +40°C

In this configuration, the floor sensor prevents the

mats and heating cables from overheating.

Prepare the controller according to the guidelines (see

tab. 1; fig. 4), and install the floor sensor (see fig. 3).

13

6. TECHNICAL SPECIFICATIONS

power supply voltage 230 VAC/50 Hz

power load at cos Ø=1 max 3600 W (res.)

temperature adjustment range from +5°C to +35°C

sensitivity ≤ 0,5°C (floor 1°C)

safety class IP 20

dimensions (h/w/l) 80 x 82 x 36 mm

installation surface mounting

control light LED

switch 1 pole

14

7. INSTALLING THE CONTROLLER

Once the appropriate temperature measurement method

has been chosen and the proper controller installation

location has been determined, the installation process

can begin. Follow the steps described below:

loosen the fixing screw and remove

the controller cover,

put all cables through the opening

in the bottom of the cover,

using two screws, positioned vertically,

tighten the controller to the installation box,

referring to the diagram, connect all cables

to the connection strip,

install the front cover and tighten the fixing screw.

15

8. SWITCHING THE CONTROLLER

ON AND ITS ADJUSTMENTS

The controller is switched on and off with the help of

the switch located on the left-hand side of the cover

(position "0" off, position "1" on) -(1). The desired

temperature is set with the dial -(2). The red LED

illuminates when the heating circuit is powered -(3).

16

Fig. 5. Electronic temperature controller ELEKTRA ELR-10

1

2

3

20

0

5

10

15

30

25

0

1

17

ELEKTRA

ul. K. Kamińskiego 4

05-850 Ożarów Mazowiecki

Poland

tel. (+48 22) 843 32 82

fax (+48 22) 843 47 52

e-mail: [email protected]

www.elektra.eu

SERVICE

tel. (+48 22) 843 32 82

fax (+48 22) 843 47 52

e-mail: [email protected]

elektroniczny

regulator temperatury

www.elektra.pl

RU

Instrukcja montażu PL

Installation manual UK

Инструкция по монтажу

Gratulujemy Państwu zakupu

elektronicznego regulatora

temperatury ELEKTRA ELR-10

i dziękujemy za zaufanie, jakim

obdarzyliście Państwo naszą

firmę. Regulator będzie służył

Wam i Waszej rodzinie przez

wiele lat. W znacznym stopniu

zaoszczędzi koszty energii

i poprawi komfort cieplny.

Przed rozpoczęciem obsługi regulatora,

prosimy uważnie przeczytać instrukcję.

ELEKTRA ELR-10

20

Strona jest ładowana ...

ELEKTRA ELR-10 Instrukcja instalacji

ELEKTRA ELR-10 Instrukcja instalacji

w innych językach

Powiązane dokumenty

Inne dokumenty