Cameo F2 FC IP Instrukcja obsługi

USER´S MANUAL

BEDIENUNGSANLEITUNG

MANUEL D´UTILISATION

MANUAL DE USUARIO

INSTRUKCJA OBSŁUGI

MANUALE D´USO

F2 FC IP

PROFESSIONAL HIGH-POWER FRESNEL WITH RGBW LED IP65

CLF2FCIP

RGBW

CONTENTS / INHALTSVERZEICHNIS / CONTENU / CONTENIDO / TREŚĆ /

CONTENUTO

ENGLISH

INFORMATION ON THIS USER MANUAL 6

INTENDED USE 6

DEFINITIONS AND SYMBOL EXPLANATIONS 6

SAFETY INSTRUCTIONS 7

NOTES ON PORTABLE OUTDOOR DEVICES 10

PACKAGING CONTENT 10

INTRODUCTION 11

CONNECTIONS, OPERATING AND DISPLAY ELEMENTS 11

OPERATION 13

SETUP AND INSTALLATION 24

ASSEMBLING / DISASSEMBLING THE SASH LIMITER AND

FILTER FRAME / CLEANING THE LENSES 25

CARE, MAINTENANCE AND REPAIR 27

DIMENSIONS 28

TECHNICAL DATA 29

EXPLANATION OF IP PROTECTION CLASS 31

MINIMUM DISTANCE TO ILLUMINATED SURFACE 31

MINIMUM DISTANCE TO NORMALLY FLAMMABLE MATERIALS 31

DISPOSAL 32

MANUFACTURER’S DECLARATIONS 33

DEUTSCH

INFORMATIONEN ZU DIESER BEDIENUNGSANLEITUNG 34

BESTIMMUNGSGEMÄSSER GEBRAUCH 34

BEGRIFFS- UND SYMBOLERKLÄRUNGEN 34

SICHERHEITSHINWEISE 35

HINWEISE FÜR ORTSVERÄNDERLICHE OUTDOOR-GERÄTE 38

LIEFERUMFANG 38

EINFÜHRUNG 39

ANSCHLÜSSE, BEDIEN- UND ANZEIGEELEMENTE 39

BEDIENUNG 41

AUFSTELLUNG UND MONTAGE 53

FLÜGELBEGRENZER UND FILTERRAHMEN MONTIEREN /

DEMONTIEREN / LINSEN REINIGEN 54

PFLEGE, WARTUNG UND REPARATUR 55

ABMESSUNGEN 57

TECHNISCHE DATEN 58

ERLÄUTERUNGEN ZUR IP-SCHUTZART 60

MINDESTABSTAND ZUR BELEUCHTETEN FLÄCHE 60

MINDESTABSTAND ZU NORMAL ENTFLAMMBAREN MATERIALIEN 60

ENTSORGUNG 61

HERSTELLERERKLÄRUNGEN 62

FRANÇAIS

INFORMATIONS CONCERNANT CE MANUEL D’UTILISATION 63

UTILISATION CONFORME 63

EXPLICATIONS DES TERMES ET DES SYMBOLES 63

CONSIGNES DE SÉCURITÉ 64

REMARQUES CONCERNANT LES APPAREILS D’EXTÉRIEUR MOBILES 67

CONTENU DE LA LIVRAISON 67

INTRODUCTION 68

CONNECTEURS, COMMANDES ET INDICATEURS/AFFICHEURS 68

INSTALLATION ET MONTAGE 83

MONTAGE/DÉMONTAGE DES COUPE-FLUX ET DU CADRE POUR

FILTRE / NETTOYAGE DES LENTILLES 84

ENTRETIEN, MAINTENANCE ET RÉPARATION 85

DIMENSIONS 87

CARACTÉRISTIQUES TECHNIQUES 88

EXPLICATIONS RELATIVES À L’INDICE DE PROTECTIONIP 90

DISTANCE MINIMALE PAR RAPPORT À LA SURFACE ÉCLAIRÉE 90

DISTANCE MINIMALE PAR RAPPORT AUX MATÉRIAUX NORMALEMENT INFLAMMABLES 90

MISE AU REBUT 91

DÉCLARATIONS DU FABRICANT 92

ESPAÑOL

INFORMACIÓN SOBRE ESTE MANUAL DE USUARIO 93

USO ADECUADO 93

DEFINICIONES Y EXPLICACIONES DE LOS SÍMBOLOS 93

INSTRUCCIONES DE SEGURIDAD 94

INDICACIONES PARA EQUIPOS PORTÁTILES DE EXTERIOR 97

ELEMENTOS SUMINISTRADOS 97

INTRODUCCIÓN 98

CONEXIONES, CONTROLES E INDICADORES 98

OPERACIÓN 100

INSTALACIÓN Y MONTAJE 112

MONTAJE Y DESMONTAJE DE LA VISERA Y EL PORTA

FILTROS. LIMPIEZA DE LA LENTE 113

CUIDADO, MANTENIMIENTO Y REPARACIÓN 114

DIMENSIONES 116

CARACTERÍSTICAS TÉCNICAS 117

EXPLICACIÓN SOBRE LA CLASE DE PROTECCIÓN IP 119

DISTANCIA MÍNIMA A LA SUPERFICIE ILUMINADA 119

DISTANCIA MÍNIMA A MATERIALES NORMALMENTE INFLAMABLES 119

ELIMINACIÓN 120

DECLARACIÓN DEL FABRICANTE 121

POLSKI

INFORMACJE DOTYCZĄCE NINIEJSZEJ INSTRUKCJI OBSŁUGI 122

UŻYTKOWANIE ZGODNE Z PRZEZNACZENIEM 122

OBJAŚNIENIA TERMINÓW I SYMBOLI 122

ZASADY BEZPIECZEŃSTWA 123

UWAGI DOTYCZĄCE PRZENOŚNEGO SPRZĘTU DO ZASTOSOWAŃ ZEWNĘTRZNYCH 126

ZAKRES DOSTAWY 126

WPROWADZENIE 127

PRZYŁĄCZA, ELEMENTY OBSŁUGI I WSKAŹNIKI 127

OBSŁUGA 129

USTAWIANIE I MONTAŻ 141

MONTAŻ / DEMONTAŻ SKRZYDEŁ OGRANICZAJĄCYCH I RAMY

FILTRA / CZYSZCZENIE SOCZEWEK 142

CZYSZCZENIE, KONSERWACJA I NAPRAWY 143

WYMIARY 145

DANE TECHNICZNE 146

OBJAŚNIENIA DOTYCZĄCE STOPNIA OCHRONY IP 148

MINIMALNA ODLEGŁOŚĆ OD POWIERZCHNI OŚWIETLANEJ 148

MINIMALNA ODLEGŁOŚĆ OD NORMALNIE ŁATWOPALNYCH MATERIAŁÓW 148

UTYLIZACJA 149

OŚWIADCZENIA PRODUCENTA 150

ITALIANO

INFORMAZIONI SUL PRESENTE MANUALE D’USO 151

UTILIZZO CONFORME 151

SPIEGAZIONE DI CONCETTI E SIMBOLI 151

INDICAZIONI SULLA SICUREZZA 152

AVVERTENZE PER DISPOSITIVI PORTATILI PER ESTERNI 155

FORNITURA 155

INTRODUZIONE 156

CONNETTORI, ELEMENTI DI COMANDO E VISUALIZZAZIONE 156

UTILIZZO 158

INSTALLAZIONE E MONTAGGIO 170

MONTAGGIO / SMONTAGGIO DEL LIMITATORE DI BATTENTI E

DEL TELAIO DEL FILTRO / PULIZIA DELLE LENTI 171

PULIZIA, MANUTENZIONE E RIPARAZIONE 172

INGOMBRO 174

DATI TECNICI 175

SPIEGAZIONI SULLA PROTEZIONE IP 177

DISTANZA MINIMA DALLA SUPERFICIE ILLUMINATA 177

DISTANZA MINIMA DAI MATERIALI NORMALMENTE INFIAMMABILI 177

SMALTIMENTO 178

DICHIARAZIONI DEL PRODUTTORE 179

DMX

DMX CONTROL / DMX STEUERUNG / PILOTAGE DMX / CONTROL DMX /

STEROWANIE DMX / CONTROLLO DMX 180

6

DMX

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCHENGLISH

ENGLISH

YOU HAVE MADE THE RIGHT CHOICE!

This device has been developed and manufactured to the highest quality standards to ensure

many years of problem-free operation. Please read this user manual carefully to be able to use

your new Cameo product quickly and optimally. Further information about Cameo Light is avail-

able on our website CAMEOLIGHT.COM.

INFORMATION ON THIS USER MANUAL

• Carefully read the safety instructions and the entire manual before operating the device.

• Observe the warnings on the device and in the user manual.

• Always keep the user manual within reach.

• If you sell or pass on the device, it is important that you also include this user manual, as it is an

integral part of the product.

INTENDED USE

The product is a device for event technology!

This product has been developed for professional use in the ﬁeld of event technology and is not

suitable for use as domestic lighting!

Furthermore, this product is only intended for qualiﬁed users with specialist knowledge of event

technology!

Use of the product outside the speciﬁed technical data and operating conditions is considered

inappropriate!

Liability for damage and third-party damage to persons and property due to inappropriate use is

excluded!

The product is not suitable for:

• Use by persons (including children) with limited physical, sensory or mental abilities or lack of

experience and knowledge.

• Children (children must be instructed not to play with the device).

DEFINITIONS AND SYMBOL EXPLANATIONS

1. HAZARD: The word HAZARD, possibly in combination with a symbol, indicates situations in

which there is an immediate danger or risk of potentially fatal injury.

2. WARNING: The word WARNING, possibly in combination with a symbol, indicates situations in

which there is an immediate danger or risk of potentially fatal injury.

3. CAUTION: The word CAUTION, possibly in combination with a symbol, indicates situations or

conditions that could result in injury.

4. ATTENTION: The word ATTENTION, possibly in combination with a symbol, indicates situations

or conditions that could result in damage to property and/or the environment.

7

DMX DEUTSCHFRANCAIS

ESPAÑOL ENGLISH

ITALIANO POLSKI

This symbol identiﬁes hazards that can cause electric shock.

This symbol identiﬁes hazardous areas or hazardous situations.

This symbol indicates hazards caused by hot surfaces.

This symbol indicates hazards caused by intense light sources.

This symbol indicates a device in which there are no user-replaceable parts.

This symbol indicates additional information on the operation of the product.

SAFETY INSTRUCTIONS

HAZARD:

1. Do not open the device and do not carry out any modiﬁcations.

2. If your device no longer functions properly, if liquids or objects get inside it or if it

has been damaged in any other way, switch it off immediately and unplug it from

the power source. The device may be repaired only by authorised repair techni-

cians.

3. For devices of protection class 1, the protective conductor must be connected

correctly. Never disconnect the protective conductor. Devices of protection class 2

do not have a protective conductor.

4. Ensure that live cables are not kinked or otherwise mechanically damaged.

5. Never bypass the device fuse.

WARNING:

1. The device may not be operated if it shows obvious signs of damage.

2. The device may only be installed in a voltage-free state.

3. If the device's power cable is damaged, the device may not be used.

4. Permanently connected power cables may only be replaced by a qualiﬁed person.

8

DMX

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCHENGLISH

ATTENTION:

1. Do not switch on the device if it has been exposed to extreme temperature ﬂuctu-

ations (for example, following transport). Moisture and condensation can damage

the device. Switch on the device only when it has reached room temperature.

2. Ensure that the voltage and frequency of the mains supply match the values spec-

iﬁed on the device. If the device has a voltage selector switch, do not connect the

device until it has been set correctly. Use only suitable power cables.

3. To disconnect the device from the mains on all poles, it is not sufﬁcient to press the

on/off switch on the device.

4. Make sure that the fuse used corresponds to the type printed on the device.

5. Ensure that suitable measures have been taken against overvoltage (e.g. lightning

strikes).

6. Observe the speciﬁed maximum output current on devices with a Power Out con-

nection. Ensure that the total current consumption of all connected devices does

not exceed the speciﬁed value.

7. Replace plug-in power cables with original cables only.

HAZARD:

1. Choking hazard! Plastic bags and small parts must be kept out of reach of persons

(including children) with reduced physical, sensory or mental capabilities.

2. Risk of falling! Make sure that the device is securely installed and will not fall

down. Only use suitable stands or mounts (particularly for ﬁxed installations).

Ensure that accessories are properly installed and secured. Ensure that applicable

safety regulations are observed.

WARNING:

1. Use the device in the prescribed manner only.

2. Operate the device using only accessories of the type recommended and supplied

by the manufacturer.

3. Observe safety regulations applicable in your country during installation.

4. After connecting the device, ensure that all cables are routed so as to avoid dam-

age or accidents, such as from tripping.

5. Always observe the speciﬁed minimum distance to normally ﬂammable materials!

Unless explicitly stated, the minimum distance is 0.3m.

9

DMX DEUTSCHFRANCAIS

ESPAÑOL ENGLISH

ITALIANO POLSKI

CAUTION:

1. Moving components such as mounting brackets may become jammed.

2. In the case of devices with motor-driven components, there is a risk of injury due

to the movement of the device. Sudden movement of the device can cause shock

reactions.

3. The housing surface of the device can become very hot during regular operation.

Ensure that accidental touching of the housing is not possible. Always allow the

device to cool sufﬁciently before removal, maintenance work and charging etc.

ATTENTION:

1. Do not install or use the device in the vicinity of radiators, accumulators, stoves, or

other heat sources. Ensure that the device is always installed in such a way that it

is sufﬁciently cooled and cannot overheat.

2. Do not place any ignition sources, such as burning candles, near the device.

3. Ventilation openings must not be covered and fans must not be blocked.

4. For transport, use the original packaging or packaging provided by the manufactur-

er.

5. Avoid any impacts to or shaking of the device.

6. Observe the IP rating and the ambient conditions such as temperature and humidi-

ty according to the speciﬁcations.

7. Devices can be continuously further developed. In the event of deviating informa-

tion on operating conditions, performance or other device properties between the

user manual and the device labelling, the information on the device always has

priority.

8. The device is not suitable for tropical climate zones or for operation over 2,000 m

above sea level.

9. Unless explicitly stated, the device is not suitable for operation under marine

conditions.

PLEASE NOTE:

For conversion or retroﬁt sets or accessories provided by the manufacturer, it is

essential to observe the instructions included.

10

DMX

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCHENGLISH

CAUTION! IMPORTANT INFORMATION REGARDING LIGHTING PRODUCTS!

1. Never look directly into the beam of light, not even for a short period of time.

2. Never look into the beam of light using optical devices such as a magnifying glass.

3. Stroboscopic effects may cause epileptic seizures in susceptible individuals!

4. Permanently installed lamps are built into these lighting units. These may not be

replaced by the user. The lamps contained in this lighting unit may only be replaced

by the manufacturer, its service partner, or a similarly qualiﬁed person.

NOTES ON PORTABLE OUTDOOR DEVICES

1. Temporary operation! Event equipment is generally only designed for temporary

operation.

2. Continuous operation or permanent structural installation – particularly outdoors –

can impair the function, surfaces and seals and accelerate material fatigue.

3. Damage to the surface coating can impair the device‘s corrosion protection.

Damaged surface coating (e.g. scratches) must be promptly repaired by suitable

measures.

PACKAGING CONTENT

Remove the product from the packaging and remove all packaging material.

Please check the completeness and integrity of the delivery and notify your distribution partner

immediately after purchase if the delivery is not complete or if it is damaged.

Included with the product CLF2FCIP are:

X 1 x Cameo F2 FC IP Floodlight

X 1x power cable

X 1 x sash limiter

X 1 x ﬁlter frame

X User manual

11

DMX DEUTSCHFRANCAIS

ESPAÑOL ENGLISH

ITALIANO POLSKI

INTRODUCTION

Professional High-Power Fresnel with RGBW LED

CLF2FCIP

CONTROL FUNCTIONS

1-channel, 2-channel DIM, 2-channel CCT, 3-channel RGB, 4-channel RGBW, 4-channel CCT,

6-channel HSI/CCT, 7-channel RGB/CCT, 8-channel RGBW 16Bit, 10-channel HSI/CCT, 16-channel

RGBW/CCT 16Bit

Master/slave operation

Standalone functions

FEATURES

IP65 protection class. 1 x High Power 240W RGBW LED. 17°– 53° beam angle, manual zoom.

200mm Fresnel lens. Adjustable PWM frequency (ﬂicker-free). DMX-512 control. RDM-enabled.

Manual control. 4 dimming curves. 16 bit dimming. Master/Slave operation. Extremely quiet

operation due to combined heat pipe and fan cooling. Operating voltage 100–240 V AC/50–60Hz.

Power consumption 220W. Mounting bracket, flter frame and 8-position barn doors included.

The spotlight features the RDM standard (Remote Device Management). Remote device manage-

ment allows the user to view the status and conﬁguration of RDM terminals via an RDM-capable

controller.

CONNECTIONS, OPERATING AND DISPLAY ELEMENTS

ESC

F2 FC IP

DIM

SELECT

ENTER 1 3 4

5

6

7

8

9

10

2

1 POWER IN

TRUE1-compatible mains input socket. Operating voltage 100–240 V AC/50–60 Hz.

2 POWER OUT

TRUE1 kompatible Netzausgangsbuchse für die Netzversorgung weiterer CAMEO Scheinwerfer.

Ensure that the total power consumption of all devices connected to the device does not exceed

the given ampere (A) value.

12

DMX

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCHENGLISH

3 DMX IN

Male 5-pin XLR socket for connection to a DMX control device (e.g. DMX console).

4 DMX OUT

Female 5-pin XLR socket for sending the DMX control signal.

5 PRESSURE EQUALISATION ELEMENT

Pressure equalisation element to prevent condensation inside the housing. In order to ensure its

proper function, the element must be protected from contamination.

6 OLED DISPLAY

Displays currently active mode and the menu items in the Edit menu.

7 DIM/MENU

Rotary-push encoder for the adjustment and control of the spotlight.

DIM - In the standalone operating modes CCT, HSI, Direct LED, Gel, User Color and Play Loop, the

encoder has the function of the master dimmer (turn encoder).

ENTER - 1. Press ENTER to access the menu level for selecting the operating mode. 2. You move

down one level in the menu structure. 3. Press ENTER to conﬁrm a value change, such as chang-

ing the DMX address.

SELECT - Turn the encoder to select the menu items on the menu level and change a value in a

menu item (e.g. DMX address).

8 The function of the middle turn-push encoder (turn and push) is shown in the corresponding

menu item in the centre of the display (line centre = turn, line bottom = push).

9 ESC - If the press function of the right-hand rotary-push encoder is not explicitly shown at the

bottom right of the display, pressing the encoder has the function of moving up one level in the

menu structure.

10 ZOOM

On either side of the cabinet is a calibration control to manually adjust the beam angle. The two

controls are mechanically linked and are directly opposite each other on the housing. Turn the

calibration control to adjust the beam angle of the spotlight continuously from 40° to 15°. A rack

and pinion system moves the zoom tube with the Fresnel lens in and out of the housing. The

further the zoom tube protrudes from the housing, the smaller the beam angle. A stop mechanism

prevents the tube from becoming detached from the housing.

13

DMX DEUTSCHFRANCAIS

ESPAÑOL ENGLISH

ITALIANO POLSKI

ATTENTION: In order to provide protection from spraying water, in accordance with

protection class IP65, special IP65-rated XLR connectors must be used correctly with the

DMX input and output sockets, or they must be closed using the rubber sealing caps.

When connected correctly, or when sealed correctly with the rubber sealing caps, the

POWER IN and POWER OUT sockets are protected from spraying water, as in accordance

with IP65.

OPERATION

NOTES

• As soon as the spotlight is correctly connected to the power supply, the following will be

displayed in succession: „Welcome to Cameo“, the model name and the software version. After

this process, the lamp is ready for operation and starts in the previously enabled mode.

• If one of the DMX modes or slave mode is enabled and there is no control signal at the DMX

input, the characters in the display will start to ﬂash.

• If no input is made within approx. 1 minute, the currently activated operating mode is automati-

cally shown in the display (main display).

DISPLAY MAIN DISPLAY DMX MODE

The main display in DMX mode shows the currently set DMX start address, DMX mode and other

information (see illustration).

 = DMX signal is present  = no DMX signal

currently activated operating mode

DMX start address and DMX mode

Fan mode

Press encoder =

Open main menu (Menu)

Press encoder =

Selection of the operating mode

(Mode)

4CH Direct

14

DMX

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCHENGLISH

DMX-STARTADRESSE EINSTELLEN (DMX Address)

Starting from the main display, press the rotary-push encoder to enter the main menu. Turn the

left encoder (SELECT) to select the menu item DMX Address (note the selection arrow on the left)

and conﬁrm by pressing the encoder (ENTER). You can now conﬁgure the DMX start address as

required by rotating the encoder (the highest value depends on the selected DMX mode). At the

same time, the DMX start address following the selected start address plus the channel number

of the selected DMX mode is displayed (following Address). Conﬁrm the entry by pressing the left

encoder (ENTER), this also automatically takes you back to the main display and the DMX operat-

ing mode is activated. The menu item for selecting the desired DMX mode can be reached directly

from the menu item DMX Address by pressing the middle rotary-push encoder (DMX mode); the

previously set DMX start address is automatically saved.

Press encoder =

Open main menu (Menu)

Turn encoder =

Change value

Press encoder =

Conﬁrm value change (Enter)

Press encoder =

DMX mode selection (DMX Mode)

SET DMX MODE (DMX Mode)

Starting from the main display, press the rotary-push encoder to enter the main menu. Turn the

left encoder (SELECT) to select the menu item DMX Mode (note the selection arrow on the left)

and conﬁrm by pressing the left encoder (ENTER). Now you can select the desired DMX mode

by turning the left encoder. Conﬁrm the selection by pressing the left encoder (ENTER), this also

automatically takes you back to the main display and the DMX operating mode is activated. Tables

with the channel assignment of the different DMX modes can be found in these instructions under

DMX CONTROL.

1CH DIM

2CH DIM 16Bit

2CH CCT

3CH RGB cal.

4CH Direct

4CH CCT 16Bit

6CH HSI-CCT

7CH RGB-CCT

8CH Direct 16Bit

10CH HSI-CCT

16CH Direct CCT

15

DMX DEUTSCHFRANCAIS

ESPAÑOL ENGLISH

ITALIANO POLSKI

CCT STANDALONE MODE (Correlated Colour Temperature)

Starting from the main display, press the left-hand rotary-push encoder to access the menu for

selecting the operating mode. Turn the left encoder (SELECT) to select the CCT mode (note the

selection arrow on the left) and conﬁrm by pressing the left encoder (ENTER). You can now set the

brightness (DIM), colour temperature (CCT) and hue (Tint) using the three rotary-push encoders

(see illustration).

currently activated operating mode Fan mode

Turn encoder =

Set colour tone (Tint)

Press encoder =

Open main menu (Menu)

Turn encoder =

Set brightness (DIM)

Press encoder =

Selection of the operating mode

(Mode) Turn encoder =

Set colour temperature (CCT)

STANDALONE OPERATING MODE HSI (Hue – Saturation – Intensity)

Starting from the main display, press the left-hand rotary-push encoder to access the menu for

selecting the operating mode. Turn the left encoder (SELECT) to select the HSI operating mode

(note the selection arrow on the left) and conﬁrm by pressing the left encoder (ENTER). You can

now set the brightness (DIM), hue (HUE) and colour saturation (SAT) using the three rotary-push

encoders (see illustration).

currently activated operating mode Fan mode

Turn encoder =

Set colour saturation (SAT)

Press encoder =

Open main menu (Menu)

Turn encoder =

Set brightness (DIM)

Press encoder =

Selection of the operating mode

(Mode) Turn encoder = set

colour tone (HUE)

16

DMX

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCHENGLISH

STANDALONE OPERATING MODE DIRECT LED (RGBW colour mixing)

Starting from the main display, press the left-hand rotary-push encoder to access the menu for

selecting the operating mode. Turn the left encoder (SELECT) to select the Direct LED mode (note

the selection arrow on the left) and conﬁrm by pressing the left encoder (ENTER). Now set the

total brightness (DIM) and the intensity of R, G, B and W using the three rotary-push encoders (see

illustration).

currently activated operating mode Fan mode

Turn encoder

Set brightness of G or W

Press encoder =

Open main menu (Menu)

Turn encoder =

Set overall brightness (DIM)

Press encoder =

Selection of the operating mode

(Mode) Turn encoder =

Set brightness of R or B

Press encoder =

switch between R+G and B+W (colour)

STANDALONE OPERATING MODE GEL (colour ﬁlter presets)

Starting from the main display, press the left-hand rotary-push encoder to access the menu

for selecting the operating mode. Turn the left encoder (SELECT) to select the GEL mode (note

the selection arrow on the left) and conﬁrm by pressing the left encoder (ENTER). Now set the

brightness (DIM) and colour ﬁlter preset (gel) using the left and middle rotary-push encoders (see

illustration). For the colour ﬁlter presets with Lee ﬁlter names, please refer to the DMX tables

under DMX CONTROL (channel 8 colour presets in 10-channel DMX mode, without User Colors).

currently activated operating mode Fan mode

Press encoder =

Open main menu (Menu)

Turn encoder =

Set overall brightness (DIM)

Press encoder =

Selection of the operating mode

(Mode) Turn encoder =

Select ﬁlter preset

17

DMX DEUTSCHFRANCAIS

ESPAÑOL ENGLISH

ITALIANO POLSKI

STANDALONE OPERATING MODE USER COLOR (Individual colour presets 1–8)

Starting from the main display, press the left-hand rotary-push encoder to access the menu for

selecting the operating mode. Turn the left encoder (SELECT) to select the User Color mode (note

the selection arrow on the left) and conﬁrm by pressing the left encoder (ENTER). Select one of

the 8 pre-programmed, but individually editable colour presets by turning the left encoder again.

Conﬁrm the selection by pressing the left encoder (ENTER). Now set the brightness (DIM) of the

colour preset using the left encoder (see illustration). Individual preset settings and renaming of

presets can be done in the menu item Edit User Color.

currently activated operating mode Fan mode

Press encoder =

Open main menu (Menu)

Turn encoder =

Set brightness (DIM)

Press encoder =

Selection of the operating mode

(Mode) Turn encoder =

Select ﬁlter preset

EDIT STANDALONE OPERATING MODE USER COLOR (Edit User Colour)

Starting from the main display, press the rotary-push encoder to enter the main menu. Turn the

left encoder (SELECT) to select the menu item Edit User Color (note the selection arrow on the

left) and conﬁrm by pressing the left encoder (ENTER). Now you can select one of the 8 colour

presets by turning the left encoder and conﬁrm the selection by pressing the left encoder (ENTER).

Now give the preset an individual, up to 12-digit name (Edit User Colour Name) by turning the left

encoder to select a letter, the underscore or a number for the ﬁrst digit of the preset name and

conﬁrm by pressing the left encoder. This is followed by the input for the second digit and so on.

When the preset name is complete, press the middle encoder (Save&Next) to move to the next

editing step. If you press Save&Next before selecting a letter, an underscore, or a number for the

ﬁrst digit, the previous preset name is retained and you move immediately to the next editing step.

18

DMX

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCHENGLISH

Now decide in which way you want to create the colour for the preset, choose between the 4

methods CCT, HSI, DIRECT and GEL by turning the left encoder (SELECT) and conﬁrm by pressing

the left encoder (ENTER).

Now set the desired colour as described in the instructions for the respective standalone mode

and press the left encoder (ENTER/Save) to conﬁrm.

STANDALONE OPERATING MODE PLAY LOOP (8-step colour sequences 1–8)

Starting from the main display, press the left-hand rotary-push encoder to access the menu for

selecting the operating mode. Turn the left encoder (SELECT) to select the Play Loop mode (note

the selection arrow on the left) and conﬁrm by pressing the left encoder (ENTER). Select one of

the 8 pre-programmed but individually editable colour sequences by turning the left encoder

again. Conﬁrm the selection by pressing the left encoder (ENTER). Now set the brightness (DIM)

of the colour sequence using the left encoder, the step duration (0.1 seconds to 21 minutes and

2 random modes) and the fade time (0 seconds to 18 minutes and 2 random modes) using the

middle and right encoders (see illustration). The individual settings and renaming of the colour

sequences can be done in the menu item Edit Loop in the main menu.

currently activated operating mode Fan mode

Turn encoder =

Set fade time (t-fade)

Press encoder =

Open main menu (Menu)

Turn encoder =

Set brightness (DIM)

Press encoder =

Selection of the operating mode

(Mode) Turn encoder =

Set step duration (t-Step)

Press encoder =

back to colour sequence selection (Back)

19

DMX DEUTSCHFRANCAIS

ESPAÑOL ENGLISH

ITALIANO POLSKI

EDIT STANDALONE OPERATING MODE PLAY LOOP (Edit Loop)

Starting from the main display, press the rotary-push encoder to enter the main menu. Turn the

left encoder (SELECT) to select the menu item Edit Loop (note the selection arrow on the left) and

conﬁrm by pressing the left encoder (ENTER). Now you can select one of the 8 colour sequences

by turning the left encoder and conﬁrm the selection by pressing the left encoder (ENTER).

Now give the colour sequence an individual, up to 12-digit name (Edit Loop Name) by turning the

left encoder to select a letter, the underscore or a number for the ﬁrst digit of the preset name and

conﬁrm by pressing the left encoder. This is followed by the input for the second digit and so on.

When the preset name is complete, press the middle encoder (Save&Next) to move to the next

editing step. If you press Save&Next before selecting a letter, an underscore, or a number for the

ﬁrst digit, the previous preset name is retained and you move immediately to the next editing step.

Select step 1 of the 8-step sequence (Step1 - Step8) by turning the left encoder, then set the

colour of the step (Step1, note the selection arrow). Now select one of the colours set in the

standalone mode User Color by turning the middle encoder and conﬁrm the selection for step

1 by pressing the middle encoder. The selected colour of the respective step is visually indicated

by a box with a light background below the colour numbers 1 to 8. Proceed in the same way to

set the colours of steps 2 to 8. Complete the process and save the sequence by pressing the left

encoder (ENTER).

20

DMX

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCHENGLISH

SLAVE MODE

Starting from the main display, press the left-hand rotary-push encoder to access the menu for

selecting the operating mode. Turn the left encoder to select the Slave menu item (note the selec-

tion arrow on the left) and conﬁrm by pressing the encoder (ENTER). Slave mode is now enabled,

and the main display is automatically displayed. Connect the slave unit and the master unit (same

model, same software version) using a DMX cable and activate one of the standalone operating

modes in the master unit. The slave unit will now follow the master unit.

currently activated operating mode Fan mode

Press encoder =

Open main menu (Menu)

Press encoder =

Selection of the operating mode

(Mode)

DMX OPERATION

Starting from the main display, press the left-hand rotary-push encoder to access the menu for

selecting the operating mode. Turn the left encoder to select the menu item DMX (note the selec-

tion arrow on the left) and conﬁrm by pressing the encoder (ENTER). DMX mode is now activated

and the main display is automatically shown again. Select one of the ten available DMX modes in

the DMX Mode menu item in the main menu (see SET DMX MODE).

DEVICE SETTINGS (Settings)

Starting from the main display, press the rotary-push encoder to enter the main menu. Turn the

left encoder (SELECT) to select the Settings menu item (note the selection arrow on the left)

and conﬁrm by pressing the left encoder (ENTER). This takes you to the submenu for setting the

submenu items (see table, select with SELECT, conﬁrm with ENTER, change value or status with

SELECT, conﬁrm with ENTER ).

Strona jest ładowana ...

Cameo F2 FC IP Instrukcja obsługi

Cameo F2 FC IP Instrukcja obsługi

w innych językach

Powiązane dokumenty

Inne dokumenty