Cameo PIXBAR® 600 IP G2 Instrukcja obsługi

USER´S MANUAL

BEDIENUNGSANLEITUNG

MANUEL D`UTILISATION

MANUAL DE USUARIO

INSTRUKCJA OBSŁUGI

MANUALE D‘ USO

PIXBAR® G2

IP65 LED BAR

CLPB400IPG2 (RGBW) / CLPB600IPG2 (RGBWAUV)

RGBW

RGBWA

CONTENTS / INHALTSVERZEICHNIS / CONTENU /

CONTENIDO / TREŚĆ / CONTENUTO

ENGLISH

INFORMATION ON THIS USER MANUAL 6

INTENDED USE 6

DEFINITIONS AND SYMBOLS 6

SAFETY INSTRUCTIONS 7

NOTES ON PORTABLE OUTDOOR DEVICES 11

PACKAGING CONTENT 11

INTRODUCTION 11

CONNECTIONS, OPERATING AND DISPLAY ELEMENTS 13

OPERATION 14

INSTALLATION 27

FROST FILTER 32

GLARE SHIELD 32

CARE, MAINTENANCE AND REPAIR 33

OPTIONAL ACCESSORIES 34

DIMENSIONS (mm) 35

TECHNICAL DATA 36

EXPLANATIONS ON IP RATING 38

MINIMUM DISTANCE TO ILLUMINATED SURFACE 39

MINIMUM DISTANCE TO NORMALLY FLAMMABLE MATERIALS 39

DISPOSAL 39

MANUFACTURER’S DECLARATIONS 40

DEUTSCH

INFORMATIONEN ZU DIESER BEDIENUNGSANLEITUNG 41

BESTIMMUNGSGEMÄSSER GEBRAUCH 41

BEGRIFFS- UND SYMBOLERKLÄRUNGEN 41

SICHERHEITSHINWEISE 42

HINWEISE FÜR ORTSVERÄNDERLICHE OUTDOOR-GERÄTE 46

LIEFERUMFANG 46

EINFÜHRUNG 46

ANSCHLÜSSE, BEDIEN- UND ANZEIGEELEMENTE 48

BEDIENUNG 49

MONTAGE 63

FROSTFILTER 69

BLENDSCHUTZ 69

PFLEGE, WARTUNG UND REPARATUR 70

OPTIONALES ZUBEHÖR 71

ABMESSUNGEN (mm) 72

TECHNISCHE DATEN 73

ERLÄUTERUNGEN ZUR IP-SCHUTZART 75

MINDESTABSTAND ZUR BELEUCHTETEN FLÄCHE 76

MINDESTABSTAND ZU NORMAL ENTFLAMMBAREN MATERIALIEN 76

ENTSORGUNG 76

HERSTELLERERKLÄRUNGEN 77

FRANÇAIS

INFORMATIONS SUR CE MANUEL D'UTILISATION 78

UTILISATION PRÉVUE 78

DÉFINITIONS ET EXPLICATION DES PICTOGRAMMES 78

CONSIGNES DE SÉCURITÉ 79

NOTES SUR LES APPAREILS PORTABLES POUR EXTÉRIEUR 83

CONTENU DU CARTON 83

INTRODUCTION 84

CONNECTEURS, UTILISATION ET INDICATEURS 85

FONCTIONNEMENT 86

MONTAGE 100

FILTRE FROST 105

ÉCRAN ANTI-ÉBLOUISSEMENT 105

ENTRETIEN, MAINTENANCE ET RÉPARATIONS 106

ACCESSOIRES EN OPTION 107

DIMENSIONS (mm) 108

CARACTÉRISTIQUES TECHNIQUES 109

EXPLICATION DE LA CLASSE DE PROTECTION IP 112

DISTANCE MINIMALE PAR RAPPORT À LA SURFACE ÉCLAIRÉE 112

DISTANCE MINIMALE PAR RAPPORT AUX MATÉRIAUX NORMALEMENT 113

INFLAMMABLES 113

MISE AU REBUT 113

DÉCLARATIONS DU FABRICANT 113

ESPAÑOL

INFORMACIÓN SOBRE ESTE MANUAL DE USUARIO 115

USO ADECUADO 115

DEFINICIONES Y EXPLICACIONES DE LOS SÍMBOLOS 115

INSTRUCCIONES DE SEGURIDAD 116

INDICACIONES PARA EQUIPOS PORTÁTILES DE EXTERIOR 120

ELEMENTOS SUMINISTRADOS 120

INTRODUCCIÓN 121

CONEXIONES, CONTROLES E INDICADORES 122

OPERACIÓN 123

MONTAJE 136

FILTRO FROST 141

PROTECCIÓN ANTIRREFLEJO 141

CUIDADO, MANTENIMIENTO Y REPARACIÓN 142

ACCESORIOS OPCIONALES 143

DIMENSIONES (mm) 144

CARACTERÍSTICAS TÉCNICAS 145

EXPLICACIÓN SOBRE LA CLASE DE PROTECCIÓN IP 147

DISTANCIA MÍNIMA A LA SUPERFICIE ILUMINADA 148

DISTANCIA MÍNIMA A MATERIALES NORMALMENTE INFLAMABLES 148

ELIMINACIÓN 148

DECLARACIÓN DEL FABRICANTE 149

POLSKI

INFORMACJE NA TEMAT NINIEJSZEJ INSTRUKCJI OBSŁUGI 150

ZAMIERZONE ZASTOSOWANIE 150

DEFINICJE I OBJAŚNIENIA SYMBOLI 150

INSTRUKCJE BEZPIECZEŃSTWA 151

UWAGI DOTYCZĄCE PRZENOŚNYCH URZĄDZEŃ ZEWNĘTRZNYCH 155

ZAKRES DOSTAWY 155

WPROWADZENIE 156

PRZYŁĄCZA, ELEMENTY OBSŁUGI I WSKAŹNIKI 157

OBSŁUGA 158

INSTALACJA 172

FILTR FROST 178

OCHRONA PRZECIWODBLASKOWA 178

PIELĘGNACJA, KONSERWACJA I NAPRAWA 179

CONTENTS / INHALTSVERZEICHNIS / CONTENU /

CONTENIDO / TREŚĆ / CONTENUTO

AKCESORIA OPCJONALNE 180

WYMIARY (mm) 181

DANE TECHNICZNE 182

WYJAŚNIENIE KLASY OCHRONY IP 184

MINIMALNA ODLEGŁOŚĆ OD OŚWIETLANEJ POWIERZCHNI 185

MINIMALNA ODLEGŁOŚĆ OD NORMALNIE ŁATWOPALNYCH MATERIAŁÓW 185

UTYLIZACJA 185

DEKLARACJE PRODUCENTA 186

ITALIANO

INFORMAZIONI SU QUESTO MANUALE D’ISTRUZIONI 187

USO CONFORME 187

SPIEGAZIONE DI TERMINI E SIMBOLI 187

INDICAZIONI SULLA SICUREZZA 188

AVVERTENZE PER DISPOSITIVI PORTATILI PER ESTERNI 192

DOTAZIONE 192

INTRODUZIONE 192

CONNESSIONI, ELEMENTI DI COMANDO E INDICATORI 194

UTILIZZO 195

MONTAGGIO 209

FILTRO FROST 214

PROTEZIONE ANTIRIFLESSO 214

CURA, MANUTENZIONE E RIPARAZIONE 215

ACCESSORI OPZIONALI 216

DIMENSIONI (mm) 217

DATI TECNICI 218

SPIEGAZIONI SULLA CLASSE DI PROTEZIONE IP 220

DISTANZA MINIMA DALLA SUPERFICIE ILLUMINATA 221

DISTANZA MINIMA DA MATERIALI NORMALMENTE INFIAMMABILI 221

SMALTIMENTO 221

DICHIARAZIONI DEL FABBRICANTE 222

DMX

DMX CONTROL / DMX STEUERUNG / PILOTAGE DMX / 223

CONTROL DMX / STEROWANIE DMX / CONTROLLO DMX : PB 400 IP G2 223

DMX CONTROL / DMX STEUERUNG / PILOTAGE DMX / 254

CONTROL DMX / STEROWANIE DMX / CONTROLLO DMX : PB 600 IP G2 254

6

DMX

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCHENGLISH

ENGLISH

You have made the right choice!

This device has been developed and manufactured to the highest quality standards to ensure

many years of problem-free operation. Please read this user manual carefully to be able to use

your new Cameo product quickly and optimally. Further information about Cameo Light is availab-

le on our website CAMEOLIGHT.COM.

INFORMATION ON THIS USER MANUAL

• Carefully read the safety instructions and the entire manual before operating the device.

• Observe the warnings on the device and in the user manual.

• Always keep the user manual within reach.

• If you sell or pass on the device, it is important that you also include this user manual, as it is an

integral part of the product.

INTENDED USE

The product is a device for event technology!

This product has been developed for professional use in the field of event technology and is not

suitable for use as domestic lighting!

Furthermore, this product is only intended for qualified users with specialist knowledge of event

technology!

Use of the product outside the specified technical data and operating conditions is considered

improper use!

Liability for damage and third-party damage to persons and property due to inappropriate use is

excluded!

The product is not suitable for:

• Use by persons (including children) with limited physical, sensory or mental abilities or lack of

experience and knowledge.

• Children (children must be instructed not to play with the device).

DEFINITIONS AND SYMBOLS

1. DANGER: The word DANGER, possibly in combination with a symbol, indicates immediately

dangerous situations or conditions for life and limb.

2. WARNING: The word WARNING, possibly in combination with a symbol, indicates potentially

dangerous situations or conditions for life and limb.

3. CAUTION: The word CAUTION, possibly in combination with a symbol, is used to indicate situa-

tions or conditions that may lead to injury.

4. ATTENTION: The word ATTENTION, possibly in combination with a symbol, refers to situations

or states that can lead to damage to property and/or the environment.

7

DMX DEUTSCHFRANCAIS

ESPAÑOL ENGLISH

ITALIANO POLSKI

This symbol identiﬁes hazards that can cause electric shock.

This symbol identiﬁes hazardous areas or hazardous situations.

This symbol indicates hazards caused by hot surfaces.

This symbol indicates hazards caused by intense light sources.

This symbol indicates a device in which there are no user-replaceable parts.

This symbol indicates additional information on the operation of the product.

SAFETY INSTRUCTIONS

DANGER:

1. Do not open or modify the unit.

2. If your device no longer functions properly, if liquids or objects get inside it or if it

has been damaged in any other way, switch it off immediately and disconnect it

from the mains. The device may be repaired only by authorised repair technicians.

3. For devices of protection class 1, the protective conductor must be connected

correctly. Never disconnect the protective conductor. Devices of protection class 2

do not have a protective conductor.

4. Ensure that live cables are not kinked or otherwise mechanically damaged.

5. Never bypass the unit fuse.

WARNING:

1. The device may not be operated if it shows obvious signs of damage.

2. The device may only be installed in a voltage-free state.

3. If the power cable of the device is damaged, do not operate the device.

4. Permanently connected power cables may only be replaced by a qualified person.

8

DMX

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCHENGLISH

ATTENTION:

1. Do not operate the unit if it has been exposed to large temperature fluctuations

(for example, after transport). Moisture and condensation can damage the device.

Switch on the device only when it has reached room temperature.

2. Make sure that the voltage and frequency of the mains supply correspond to the

values indicated on the unit. If the device has a voltage selector switch, do not

connect the device until it has been set correctly. Use only suitable power cables.

3. To disconnect the unit from the mains at all poles, it is not sufficient to press the

on/off switch on the unit.

4. Make sure that the fuse used corresponds to the type printed on the unit.

5. Make sure that appropriate measures have been taken against overvoltage (e.g.

lightning strike).

6. Observe the specified maximum output current on units with Power Out connec-

tion. Ensure that the total current consumption of all connected devices does not

exceed the specified value.

7. Replace pluggable mains cables only with original cables.

DANGER:

1. Danger of suffocation! Plastic bags and small parts must be kept out of reach of

persons (including children) with reduced physical, sensory or mental capabilities.

2. Danger from falling down! Make sure that the device is securely installed and will

not fall down. Only use suitable stands or mounts (particularly for fixed installa-

tions). Ensure that accessories are properly installed and secured. Ensure that

applicable safety regulations are observed.

WARNING:

1. Use the device only in the manner intended.

2. Operate the device only with the accessories recommended and intended by the

manufacturer.

3. During installation, observe the safety regulations applicable in your country.

4. After connecting the unit, check all cable routes to avoid damage or accidents, e.g.

due to tripping hazards.

5. Always observe the specified minimum distance to normally flammable materials!

Unless explicitly stated, the minimum distance is 0.3 m.

6. Always observe the minimum distance to the illuminated surface that can be read

on the device!

9

DMX DEUTSCHFRANCAIS

ESPAÑOL ENGLISH

ITALIANO POLSKI

CAUTION:

1. In the case of moving components such as mounting brackets or other moving

components, there is a possibility of jamming.

2. In the case of units with motor-driven components, there is a risk of injury from the

movement of the unit. Sudden movement of the device can cause shock reactions.

3. The housing surface of the device can become very hot during regular operation.

Ensure that accidental touching of the housing is not possible. Always allow the

lamp to cool sufficiently before removal, maintenance work and charging etc.

ATTENTION:

1. Do not install or operate the device near any radiators, heat registers, stoves or other

heat sources. Ensure that the device is always installed in such a way that it is suffi-

ciently cooled and cannot overheat.

2. Do not place ignition sources such as burning candles near the device.

3. Ventilation openings must not be covered and fans must not be blocked.

4. Use the original packaging or packaging provided by the manufacturer for trans-

port.

5. Avoid shock or impact to the unit.

6. Observe the IP rating as well as the ambient conditions such as temperature and

humidity according to the specification.

7. Devices can be constantly further developed. In the event of deviating information on

operating conditions, performance or other device properties between the user manual

and the device labelling, the information on the device always takes priority.

8. The unit is not suitable for tropical climates and for operation above 2000 m above

sea level.

9. Unless explicitly stated, the unit is not suitable for operation in marine conditions .

PLEASE NOTE:

For conversion or retroﬁt sets or accessories provided by the manufacturer, it is

essential to observe the instructions included.

CAUTION! IMPORTANT INFORMATION REGARDING LIGHTING PRODUCTS!

1. Never look directly into the beam of light, not even for a short period of time.

2. Never look into the beam of light using optical devices such as a magnifying glass.

3. Stroboscopic effects may cause epileptic seizures in susceptible individuals!

4. Permanently installed lamps are built into these lighting units. These may not

be replaced by the user. In the event of a fault, please contact your distribution

partner.

10

DMX

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCHENGLISH

SIGNAL TRANSMISSION AND CONTROL BY RADIO (e.g. W-DMX or audio radio

systems, Bluetooth):

The quality and performance of wireless signal transmissions generally depends on

the ambient conditions.

The following factors can impact range and signal stability, for example:

Shielding (e.g. masonry, metal structures, water)

High volumes of radio traffic (e.g. powerful wireless LAN networks)

Interference

Electromagnetic radiation (e.g. LED video screens, dimmers)

All range specifications refer to free-field application with visual contact and without

interference!

The operation of transmission systems is subject to official regulations. These may

vary from region to region and must be checked by the operator before use (e.g. radio

frequency and transmission power).

WARNING: Devices with wireless signal transmission are not suitable for use in sen-

sitive areas in which radio operation can lead to potential detrimental effects. These

include e.g.:

• Hospitals, health centres or other healthcare facilities that provide patient treatment

with skilled personnel and equipment.

• Hazardous areas Class I, II and III

• Restricted areas

• Military facilities

• Aircraft or vehicles

• Areas where the use of mobile phones is prohibited

TRANSMISSION VIA W-DMX

WARNING: In general, wireless DMX transmission must not be used for applications

with safety-related factors that could result in personal injury or property damage in

the event of failure.

This applies in particular to moving scene or traverse structures, DMX-controlled mo-

tors/lifts or lifting devices for operating DMX-operated platform lifts, hydraulic systems

or comparable moving components.

Furthermore, wireless DMX transmission must not be used to trigger flame or pyro-

technic devices, explosion-driven effects, or to control gas or liquid effects. These

include e.g. CO2 cannons, confetti shooters, water effects or similar.

11

DMX DEUTSCHFRANCAIS

ESPAÑOL ENGLISH

ITALIANO POLSKI

NOTES ON PORTABLE OUTDOOR DEVICES

1. Temporary operation! Event equipment is generally only designed for temporary

operation.

2. Continuous operation or permanent structural installation – particularly outdoors –

can impair the function, surfaces and seals and accelerate material fatigue.

3. Damage to the surface coating can impair the device's corrosion protection.

Damaged surface coating (e.g. scratches) must be promptly repaired by suitable

measures.

PACKAGING CONTENT

Remove the product from the packaging and remove all packaging material.

Please check the completeness and integrity of the delivery and notify your distribution partner

immediately after purchase if the delivery is not complete or if it is damaged.

Included with the CLPB400IPG2 product are:

X1 x PIXBAR® 400 IP65 G2 RGBW spotlights

X 2 sliding mounting feet with folding SPIN16® mounting spigot (pre-assembled)

X 1 x standard frost filter

X 1 x glare shield

X 1 x power cable

X User manual

Included with the CLPB600IPG2 product are:

X1 x PIXBAR® 600 IP65 G2 RGBWAUv spotlights

X2 sliding mounting feet with folding SPIN16® mounting spigot (pre-assembled)

X1 x standard frost filter

X1 x glare shield

X1 x power cable

XUser manual

INTRODUCTION

PIXBAR® 400 IP G2 Outdoor Spotlights

CLPB400IPG2 with 16 4in1 RGBW LEDs

PIXBAR® 600 IP G2 Outdoor Spotlights

CLPB600IPG2 with 16 6in1 RGBWAUV LEDs

12

DMX

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCHENGLISH

CONTROL FUNCTIONS:

CLPB400IPG2

1-channel, 3-channel Preset, 4-channel Direct, 7-channel Direct Control, 8-channel 16-bit,

10-channel Direct CCT, 11-channel Effect Pattern, 16-channel Wash, 36-channel Pattern,

48-channel Pixel RGB, 64-channel Pixel, 68-channel Pixel Dim, D2-channel, D4-channel Preset

and D7-channel Direct DMX Control

CLPB600IPG2

1-channel, 3-channel Preset, 6-channel Direct, 9-channel Direct Control, 12-channel 16-bit,

12-channel Direct CCT, 13-channel Effect Pattern, 20-channel Wash, 44-channel Pattern,

48-channel Pixel RGB, 96-channel Pixel, 100-channel Pixel Dim, D2-channel, D4-channel Preset

and D9-channel Direct DMX Control

RDM

W-DMX™

Master/Slave modes

Stand-alone functions

FEATURES:

• IP65 Rating

• Convection cooling

• Operating voltage: 100 - 240 VAC

The spotlights feature the RDM standard (remote device management). This remote device

management enables the status query and configuration of RDM end devices via an RDM-capable

controller, such as the optionally available Cameo UNICON (item number CLIREMOTE). The Cameo

UNICON also allows access to the entire spotlight menu.

13

DMX DEUTSCHFRANCAIS

ESPAÑOL ENGLISH

ITALIANO POLSKI

CONNECTIONS, OPERATING AND DISPLAY ELEMENTS

3

1 2

4

5

6

7 8

- The CLPB400IPG2 and CLPB600IPG2 models feature

identical connections, operating and display elements -

1 POWER IN

IP65 mains input socket with rubber sealing cap (TRUE1 compatible). Operating voltage 100 - 240

VAC / 50 - 60 Hz. Connection via supplied power cable (when not in use, always close with rubber

sealing cap).

2 POWER OUT

IP65 mains output socket with rubber sealing cap (TRUE1 compatible). Facilitates power supply to

other CAMEO spotlights. Ensure that the total current consumption of all connected devices does

not exceed the value specified on the device in amperes (A) (when not in use, always close with

the rubber sealing cap).

3 DMX IN

Male IP65 5-pin XLR socket for connecting a DMX control device (e.g. DMX console, when not in

use always

close with the rubber sealing cap).

4 DMX OUT

Female IP65 5-pin XLR socket for sending DMX control signal (when not in use, always close with

the rubber sealing cap).

5 OLED DISPLAY

The OLED display shows the currently activated operating mode or the current DMX address

(main display), the menu items in the menu and the numerical value or operating mode in certain

menu items.

14

DMX

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCHENGLISH

6 TOUCH-SENSITIVE CONTROLS

MENU- Press MENU to access the main menu. Press again or repeatedly to return to the main

display.

UP and DOWN – Select the menu items in the main menu (DMX address, operating mode, etc.)

and in the sub-menus using UP and DOWN. Change value or status in a menu item, e.g. DMX

address. To quickly change a value, such as the DMX start address, press and hold UP or DOWN.

ENTER – Press ENTER to access the menu level to make value or status changes, and to access

one of the sub-menus. Confirm value or status changes by pressing ENTER.

PLEASE NOTE:

• Before navigating the unit menu, make sure that the control panel is dry and clean

so that its functionality is not impaired.

• Water on the control unit can lead to incorrect operation of the spotlight, e.g. in

outdoor operation. Therefore, after configuring the spotlight, activate the lock

function to prevent incorrect operation by water (Settings -> Display -> Autolock).

7 PRESSURE EQUALISATION ELEMENT

Pressure equalisation element to prevent condensation inside the housing. In order to ensure its

proper function, the element must be protected from contamination.

8 W-DMX™ ANTENNA

Antenna for control via W-DMX™.

ATTENTION: To ensure IP65 splash resistance for the DMX and network sockets, the

special input and output sockets must be correctly sealed with the IP65 special plugs

or the rubber sealing caps must be used for sealing. When connected correctly, or

when sealed correctly with the rubber sealing caps, the POWER IN and POWER OUT

sockets are protected from spraying water, as in accordance with IP65.

OPERATION

NOTE

• As soon as the spotlight is correctly connected to the power supply, the following are displayed

in succession: “Update wait ...” (for service purposes only), “Welcome to Cameo”, the model

name and the software version. After this process, the spotlight is ready for operation and the

previously activated operating mode is launched.

• If there is no input for approx. 30 seconds, the display automatically returns to the main dis-

play.

15

DMX DEUTSCHFRANCAIS

ESPAÑOL ENGLISH

ITALIANO POLSKI

• Note on the main display in the operating modes with external control: As soon as the control

signal is interrupted, the characters in the display start flashing; if the control signal is present

again, the flashing stops.

• Briefly pressing UP when in the main display rotates the display by 180°.

SETTING DMX START ADDRESS (DMX address)

Starting from the main display, press MENU to enter the main menu. Now use UP and DOWN to

select the menu item DMX Address and confirm with ENTER. Using the UP and DOWN buttons,

configure the desired DMX start address and press ENTER to confirm (highest value dependent

upon activated DMX mode).

CONFIGURING DMX MODE (DMX Mode)

Starting from the main display, press MENU to enter the main menu. Now use UP and DOWN to

select the menu item DMX Mode and confirm with ENTER. Now select the desired DMX mode

using UP and DOWN and confirm the selection with ENTER. DMX operating modes with DMX delay

channel and group selection (Group 0 - 24) are marked with "D". Tables with the channel assign-

ments can be found in these instructions under DMX CONTROL.

CLPB400IPG2 CLPB600IPG2

16

DMX

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCHENGLISH

DMX modes with DMX delay channel

The DMX Delay function is a simple way to create a running light effect with a large number of

spotlights that are all the same model and that are all running the same software version. This

is otherwise only achievable with a suitable DMX controller and time-consuming programming.

All the spotlights used (same models, same software version) are set to the same DMX operating

mode with DMX delay channel and controlled via the same DMX start address.

Setting the DMX delay: Select one of the DMX operating modes with DMX delay channel and

confirm the selection (in the example D4 CH Preset). Assign the spotlights to one of up to 24

groups (plus Group 0) according to preference, whereby several spotlights can be assigned to one

group. The group number is also the factor by which the set delay time set in the DMX controller

is multiplied. Confirm each entry by pressing ENTER.

The delay time (delay time of the DMX signal) is set by means of a DMX controller in the separate

DMX delay channel of the corresponding DMX mode (0.0s to 2.0s in 0.1s increments).

Setup example:

STAND-ALONE MENU MASTER / ALONE

In the stand-alone modes Direct LED, Color Preset, CCT, HSI, Auto Program and Play Loop, the

control signal of the corresponding mode can be output to slave units via XLR (DMX OUT) and

W-DMX™:

Stand Alone -> Master/Alone -> Master

If the output of the control signal is not desired, the output can be deactivated:

Stand Alone -> Master/Alone -> Alone

A delay for slave units can be set for the time-delayed output of the control signal of the

stand-alone modes Auto Program and Play Loop.

Starting from the main display, press MENU to enter the main menu. Now select the Stand Alone

menu item, confirm, select Master/Alone and confirm again.

17

DMX DEUTSCHFRANCAIS

ESPAÑOL ENGLISH

ITALIANO POLSKI

This will take you to the submenu for configuring the submenu items (see table).

Control signal is forwarded via DMX OUT

Activate DMX control signal forwarding via W-DMX

Deactivate sending of the DMX control signal via

W-DMX

Pairing with ready-to-pair W-DMX devices

Disconnect all W-DMX connections

Set DMX delay for slave units: Off, 0.1s - 2.0s

Do not forward control signal

STAND-ALONE DIRECT LED MODE

The stand-alone Direct LED mode allows dimmer, strobe, R, G, B and W (CLPB400IPG2) or R, G, B,

W, A and UV (CLPB600IPG2) to be set directly on the unit, similar to a DMX controller. In this way,

an individual scene can be created without an additional DMX controller.

Starting from the main display, press MENU to enter the main menu. Use UP and DOWN to select

Stand Alone, confirm with ENTER, then select Direct LED and confirm again with ENTER. Now

select the menu item you want to edit, confirm the selection, set the desired value and confirm

the entry.

CLPB400IPG2 CLPB600IPG2

18

DMX

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCHENGLISH

COLOUR PRESET STAND-ALONE MODE

49 different colour presets plus eight individually adjustable user presets (see Edit User Color)

are available. The brightness can be set at a higher level. Starting from the main display, press

MENU to enter the main menu. Use UP and DOWN to select the menu item Stand Alone, confirm

the selection, then select Color Preset and confirm again with ENTER. Now select GEL or User

Color and confirm the selection. The desired preset can now be selected, confirm the selection.

Now select Dimmer (brightness), confirm the selection and make the settings as desired. Confirm

the entry.

CCT STAND-ALONE MODE (Correlated Colour Temperature)

In stand-alone CCT mode, the colour temperature can be adjusted in 100K steps from 2200K to

8000K, plus the hue (tint) and brightness (dimmer). Starting from the main display, press MENU

to enter the main menu. Use UP and DOWN to select the Stand Alone menu item, confirm the

selection, then select CCT and confirm again with ENTER. Now select the menu item you want to

edit, confirm the selection and make the settings as desired. Confirm the entry.

STAND-ALONE MODE HSI (Hue - Saturation - Intensity)

In the stand-alone HSI mode, the hue, saturation and brightness can be adjusted separately as

desired. Starting from the main display, press MENU to enter the main menu. Use UP and DOWN

to select the Stand Alone menu item, confirm the selection, then select HSI and confirm again

with ENTER. Now select the menu item you want to edit, confirm the selection and make the

settings as desired. Confirm each entry.

19

DMX DEUTSCHFRANCAIS

ESPAÑOL ENGLISH

ITALIANO POLSKI

STAND-ALONE OPERATION MODE PLAY LOOP (8-step colour sequences 1 - 8)

The 8 available loops are pre-programmed at the factory, but can be customised in the Edit Loop

menu item. The brightness can be set at a higher level. Starting from the main display, press

MENU to enter the main menu. Using UP and DOWN, select the menu item Stand Alone, confirm

with ENTER, then select the submenu item Auto and confirm again with ENTER. Now select the

menu item you want to edit, confirm the selection and make the settings as desired. Confirm each

entry.

TIMER FUNCTION

The timer function allows timed control of the Direct LED, Colour Preset, CCT and HSI stand-alone

modes in such a way that the fade-in time (Fade In) can be set from 0 to 60 minutes, the dwell

time from 1 to 24 hours and the fade-out time from 0 to 60 minutes. After activation of the timer

function, the timer control will be implemented upon the next system start. Starting from the main

display, press MENU to enter the main menu. Select Stand Alone, confirm the selection, then

select Timer and confirm again. Select the setting On under Timer and confirm. For the individual

timer control settings, select Fade In, Dwell Time or Fade Out and confirm. You can now set the

respective value as desired. Confirm all entries. To deactivate the timer function, select the setting

Off under Timer and confirm the entry.

Note: The timer function is suitable for use in master/slave operation via cable and W-DMX™.

20

DMX

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCHENGLISH

EDITING USER-PRESETS (Edit User Color)

The eight user presets available in the stand-alone mode Colour Preset can be edited individually.

Starting from the main display, press MENU to enter the main menu. Using UP and DOWN you

now select the menu item Stand Alone, confirm with ENTER, then select Edit User Color and

confirm once again. Select the desired preset (User Color 1 - 8) and confirm the selection. Now

decide which way you want to create the colour for the preset and select one of the four methods

Direct, CCT, Preset and HSI and confirm the selection. Now set the desired colour as described in

the instructions for the respective stand-alone mode.

EDIT LOOP (Edit LOOP)

Brightness, step duration and fade time can be set separately for all eight loops. Starting from the

main display, press MENU to enter the main menu. Using UP and DOWN you now select the menu

item Stand Alone, confirm with ENTER, then select Edit Loop and confirm once again. Now

select the desired loop for editing and confirm the selection.

Strona jest ładowana ...

Cameo PIXBAR® 600 IP G2 Instrukcja obsługi

Cameo PIXBAR® 600 IP G2 Instrukcja obsługi

w innych językach

Powiązane dokumenty

Inne dokumenty