A guide on the use, care and maintenance
of your quality Woodson product
Models:
W.GTQI.4.CUB / W.GTQI.8.10 / W.GTQI.8.15
W.GTQI15 / W.GTQI8S.10 / W.GTQI8S.15
Woodson Toaster Grillers
& Supertoast Multi-Function Toaster Grillers
SPECIFICATION, INSTALLATION
AND OPERATION MANUAL
READ ALL INSTRUCTIONS BEFORE USE
Revision: B - 14/07/2022- 03
Page Intentionally Left Blank
Page 1
Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz
Page 2
Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz
1.0 Introduction
1.1 Your New Woodson Product . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
1.2 Australia and New Zealand Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
1.2.1 Warranty Period
1.2.2 Warranty Registration
1.3 General Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
2.0 Installation
2.1 Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
2.2 Setting Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
2.2.1 Handling
2.2.2 Unpacking
2.2.3 Positioning
2.2.4 Disposal
2.3 Electrical Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
2.4 Wall Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
2.4.1 Installation
3.0 Specification
3.1 Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
3.1.1 W.GTQI4.CUB
3.1.2 W.GTQI8.10 / W.GTQI8.15
3.1.3 W.GTQI15
3.1.4 W.GTQI8S.10 / W.GTQI8S.15
4.0 Operation
4.1 Operating Instructions - W.GTQI4.CUB / W.GTQI8.1x / W.GTQI15 . . . . . . . . . . . . . . . . 10
4.1.1 Control Panel W.GTQI4 / W.GTQI8
4.1.2 Control Panel W.GTQI15
4.1.3 Operation
4.1.4 Element Settings
4.2 Operating Instructions - W.GTQI8S.1x . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4.2.1 Control Panel W.GTQI8S.1x
4.2.2 Operation
4.2.3 Element Settings
5.0 Cleaning and Maintenance
5.1 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
5.1.1 Cleaning Schedule
5.1.2 Materials Required
5.1.3 General Information
5.1.4 Corrosion Protection
5.1.5 Surface Finish
5.1.6 Cleaning Procedure
5.1.7 Cleaning Procedure - External Surfaces
5.2 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Page 3
Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz
1.0 Introduction
Carefully read this instruction booklet, as it contains important advice for safe installation, operation and maintenance. Keep this
booklet on hand in a safe place for future reference by other operators or users.
Stoddart design, manufacture & distribute Food Service Equipment (appliances) exclusively for the commercial market.
This appliance is not designed nor intended for household or domestic use and must not be used for this purpose.
This product is intended for commercial use, and in line with Australian electrical safety standards the following warnings are provided:
• This product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision or instruction concerning the use of the product by a person
responsible for their safety. Children should be supervised to ensure that they do not play with the product
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualifi ed persons in order to avoid
a hazard
The manufacturer/distributor cannot be held responsible or liable for any injuries or damages of any kind that occur to persons, units or
others, due to abuse and misuse of this unit in regards to installation, removal, operation, servicing or maintenance, or lack of conformity
with the instructions indicated in this documentation.
Disclaimer
All units made by the manufacturer/distributor are delivered assembled, where possible, and ready to install. Any installation, removal,
servicing, maintenance and access or removal of any parts, panels or safety barriers that is not permitted, does not comply in
accordance to this documentation, or not performed by a TRAINED AND AUTHORISED SPECIALIST will result in the
IMMEDIATE LOSS OF THE WARRANTY.
The manufacturer/distributor cannot be held responsible or liable for any unauthorised modifi cations or repairs. All modifi cations or
repairs must be approved by the manufacturer/distributor in writing before initiating. All modifi cations or repairs performed to this unit
must be performed at all times by a TRAINED AND AUTHORISED SPECIALIST.
Thank you for choosing this quality Woodson product.
All Woodson products are designed and manufactured to meet the needs of food service professionals. By caring for and maintaining this new
Woodson product in accordance with these instructions, will provide many years of reliable service.
Stoddart is a wholly Australian owned company, which manufactures and/or distributes a comprehensive range of food service equipment for
kitchens, food preparation and presentation. Stoddart products are manufactured and engineered to provide excellent results whilst offering
value-for-money, ease-of-use and reliability.
1.1 Your New Woodson Product
Page 4
Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz
1.0 Introduction
Carefully read this instruction booklet, as it contains important advice for safe installation, operation and maintenance. Keep this
booklet on hand in a safe place for future reference by other operators or users.
Stoddart design, manufacture & distribute Food Service Equipment (appliances) exclusively for the commercial market.
This appliance is not designed nor intended for household or domestic use and must not be used for this purpose.
This product is intended for commercial use, and in line with Australian electrical safety standards the following warnings are provided:
• This product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision or instruction concerning the use of the product by a person
responsible for their safety. Children should be supervised to ensure that they do not play with the product
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualifi ed persons in order to avoid
a hazard
The manufacturer/distributor cannot be held responsible or liable for any injuries or damages of any kind that occur to persons, units or
others, due to abuse and misuse of this unit in regards to installation, removal, operation, servicing or maintenance, or lack of conformity
with the instructions indicated in this documentation.
Disclaimer
All units made by the manufacturer/distributor are delivered assembled, where possible, and ready to install. Any installation, removal,
servicing, maintenance and access or removal of any parts, panels or safety barriers that is not permitted, does not comply in
accordance to this documentation, or not performed by a TRAINED AND AUTHORISED SPECIALIST will result in the
IMMEDIATE LOSS OF THE WARRANTY.
The manufacturer/distributor cannot be held responsible or liable for any unauthorised modifi cations or repairs. All modifi cations or
repairs must be approved by the manufacturer/distributor in writing before initiating. All modifi cations or repairs performed to this unit
must be performed at all times by a TRAINED AND AUTHORISED SPECIALIST.
Thank you for choosing this quality Woodson product.
All Woodson products are designed and manufactured to meet the needs of food service professionals. By caring for and maintaining this new
Woodson product in accordance with these instructions, will provide many years of reliable service.
Stoddart is a wholly Australian owned company, which manufactures and/or distributes a comprehensive range of food service equipment for
kitchens, food preparation and presentation. Stoddart products are manufactured and engineered to provide excellent results whilst offering
value-for-money, ease-of-use and reliability.
• All units MUST be installed according to the procedures stated in the installation section of this manual
• In the case of new personnel, training is to be provided before operating the equipment
• DO NOT use this unit for any other purpose than its intended use
• DO NOT store explosive substances such as aerosol cans with a fl ammable propellant in or near this unit
• Keep fi ngers out of “pinch point” areas
• Unit is not waterproof DO NOT use jet sprays, hoses or pour water over/on the exterior of the unit
• Only use this unit with voltage specifi ed on the rating label
• Do NOT remove any cover panels that may be on the unit
• DO NOT use sharp objects to activate controls
• If any fault is detected, refer to troubleshooting
• The manufacturer declines any liability for damages to persons and/or things due to an improper/wrong and/or unreasonable use of the
machine
• Only specifi cally trained/qualifi ed Technicians (Stoddart, one of our service agents, or a similarly qualifi ed persons) should carry out any
and all repairs, maintenance and services
When using any electrical unit, safety precautions must always be observed.
Our units have been designed for high performance. Therefore, the unit must be used exclusively for the purpose for which it has been designed.
1.3 General Precautions
1.2.2 Warranty Registration
1.2.1 Warranty Period
1.2 Australia and New Zealand Warranty
To register your new product, go to the Stoddart warranty page: http://www.stoddart.com.au/warranty-registration
Stoddart 12 month on-site parts and labour warranty (terms and conditions apply), from the time of purchase.
To view or download the warranty terms and conditions visit: http://www.stoddart.com.au/warranty-information
Warranty & Registration
Page 5
Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz
Control Panel
Wall Mount Bracket
Toasting Rack
CAUTION
Surface is Hot
2.0 Installation
2.1 Product Overview
Page 6
Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz
2.0 Installation
2.2 Setting Up
2.2.1 Handling
2.2.2 Unpacking
2.2.3 Positioning
2.2.4 Disposal
• Use suitable means to move the unit;
- For smaller items use two people
- For large items a fork lift, pallet trolley or similar (the forks should reach completely beneath the pallet)
• Check the unit for damage before and after unpacking. If unit is damaged, contact the distributor and manufacturer
• Should any item have physical damage, report the details to the freight company and to the agent responsible for the dispatch within
48 hours of receipt. No claims will be accepted or processed after this period
• The unit is supplied fully assembled
• Remove all protective plastic film, tapes, ties and packers before installing and operating
• Clean off any remaining residue from the interior/exterior of the unit using a clean cloth dampened with warm soapy water
• Choose an area that is well ventilated and provides access for future maintenance
• Place the unit on a level stable work surface capable of supporting its weight
• Do not position the unit in:
- Wet areas
- Near heat and/or steam sources
- Near flammable substances
• Two persons required to lift the unit. Pinch point hazard when lowering unit into bench
• Allow an air gap between the unit and other objects or surfaces. A minimum gap of 100mm from all sides is recommend for normal
operational use (if the unit is near any heat sensitive material we suggest you allow additional space)
• Please consult national and local standards to ensure that your unit is positioned in accordance with any existing requirement
WARNING
Improper installation, adjustments, alterations, service or
maintenance can cause property damage, injury or death.
100mm
APPLIANCE
100mm
100mm
Front
• At the end of the appliance’s working life, make sure it is scrapped & components recycled properly
• Current environmental protection laws in the state/country of use must be observed
• Doors must be removed before disposal (if applicable)
• Power supply cable must be removed before disposal
• For further information on the recycling of this product, contact the local dealer/agent or the local body responsible for waste disposal
Page 7
Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz
Single Phase Units:
• Supplied and fi tted with an appropriately rated plug and lead, indicated as:
- 10A plug & lead fi tted
- 15A plug & lead fi tted
This unit must be installed in accordance with AS/NZS 60335.1
Some procedures in this manual require the power to the equipment to be turned off and
isolated. Turn the power OFF at the power point and unplug the power supply lead by the plug
body. If the power point is not readily accessible turn the equipment off at the isolation switch
or the circuit breaker in the switchboard. Attach a yellow “CAUTION-DO NOT OPERATE” tag.
This must be performed where relevant unless the procedures specify otherwise.
FAILURE TO DO SO MAY RESULT IN ELECTRIC SHOCK.
WARNING
Notes:
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualifi ed persons in order to avoid a
hazard. Please contact Stoddart for parts and we will advise how to do this in order to avoid any electrical hazard
• The power cable should be dry and/or isolated from moisture or water
2.4 Wall Mounting
IMPORTANT
DO NOT install unit above any heat source
2.4.1 Installation
1. Place the bracket on the wall at desired height from the worktop. Ensure the bracket is level, mark the screw hole locations and/or
outline around the bracket. Drill holes and attach the bracket to the wall using sufficient load bearing fasteners
2. Place the unit bracket slots over the bracket
3. Ensure the unit sits level
1. 2. 3.
2.3 Electrical Connection
2.0 Installation
Page 8
Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz
412
363
290 - Chamber
427
315
339
315
259 - Chamber
87
Chamber
3.1.1 W.GTQI4.CUB
3.1.2 W.GTQI8.10 / W.GTQI8.15
563
363
441 - Chamber Width
427
315
339
259 - Chamber Depth
315
87
Specifications
Model W.GTQI4.CUB
Height 363mm
Width 412mm
Depth 339mm
Power 240VAC / 50Hz / 2.22kW
10A plug & lead fitted
Specifications
Model W.GTQI8.10
Height 363mm
Width 563mm
Depth 339mm
Power 240VAC / 50Hz / 2.2kW
10A plug & lead fitted
Model W.GTQI8.15
Height 363mm
Width 563mm
Depth 339mm
Power 240VAC / 50Hz / 3.3kW
15A plug & lead fitted
3.0 Specification
3.1 Technical Specifications
Page 9
Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz
3.0 Specification
673
363
87
551 - Chamber Width
527
429
351 - Chamber Depth
405
563
362
87
411 - Chamber Width
427
315
339
315
259 - Chamber Depth
3.1.3 W.GTQI15
3.1.4 W.GTQI8S.10 / W.GTQI8S.15
Specifications
Model W.GTQI15
Height 363mm
Width 673mm
Depth 429mm
Power 240VAC / 50Hz / 3.36kW
15A plug & lead fitted
Specifications
Model W.GTQI8S.10
Height 362mm
Width 563mm
Depth 339mm
Power 240VAC / 50Hz / 2.25kW
10A plug & lead fitted
Model W.GTQI8S.15
Height 362mm
Width 563mm
Depth 339mm
Power 240VAC / 50Hz / 3.3kW
15A plug & lead fitted
Page 10
Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz
4.0 Operation
4.1.1 Control Panel W.GTQI4 / W.GTQI8
4.1.2 Control Panel W.GTQI15
4.1.3 Operation
Upon using the equipment, the following steps must be followed:
1. Turn the unit on
2. Adjust the rack height to suit the product
3. Set the “heat” dial to 5
4. Turn the “element” dial left or right to select the mode of operation: “top element” only operation or “Top & bottom element” operation
5. Turn the “timer” dial clockwise to set the required time, the unit will instantly start to heat
6. Place food item into the unit
7. When timer is finished it will switch off automatically
8. Adjust as required: increase/decrease the “timer” and “heat”. Repeat this process until the desired results have been achieved
9. Once satisfied with the results, record the settings for future reference
10. Repeat this process for different foods
4.1.4 Element Settings
Top and bottom Element:
Best for all types of standard breads, buns, focaccias and open snacks.
Top Element only:
Best for Garlic bread, herb bread, focaccias and open snacks or browning the top of the product only.
Note: The elements will be turned on for the duration the timer is set to. The elements will then be turned off, until the timer is set.
4.1 Operating Instructions - W.GTQI4.CUB / W.GTQI8.1x / W.GTQI15
Page 11
Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz
4.0 Operation
4.2.1 Control Panel W.GTQI8S.1x
4.2.2 Operation
Upon using your equipment, the following steps must be followed:
1. Turn the unit on
2. Adjust the rack height to suit the product
3. Set the “top element” and “bottom element” dials to 5
4. Select either “timer” or “on continuous” The timer can be bypassed by switching to “on continuous”, when selected the elements will
not turn off)
5. Turn the “timer” dial (if timer is selected) clockwise to set the required time, the unit will instantly start to heat
6. Place food item into the unit
7. When timer is finished unit will switch off automatically
8. Adjust as required: increase/decrease the “timer”, “top element” and “bottom element”. Repeat this process until the desired results
have been achieved
9. Once satisfied with the results, record the settings for future reference
10. Repeat this process for different foods
4.2.3 Element Settings
Top and bottom Element:
Best for all types of standard breads, buns, focaccias and open snacks.
Top Element only:
Best for Garlic bread, herb bread, focaccias and open snacks or browning the top of the product only.
Note: The elements will be turned on for the duration the timer is set to. The elements will then be turned off, until the timer is set.
4.2 Operating Instructions - W.GTQI8S.1x
Page 12
Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz
5.0 Cleaning and Maintenance
IMPORTANT
Threaded fasteners can loosen in service.
Regular inspection and adjustment
should be carried out as required
WARNING
This unit is NOT waterproof, do NOT
hose. DO NOT pour water directly onto
the unit. DO NOT immerse in water
IMPORTANT
Some commercial stainless steel
cleaners leave residue or fi lm on the
metal that may entrap fi ne particles of
food, deeming the surface not
FOOD SAFE
WARNING
Wait until the unit has cooled to a safe
temperature before undertaking any
cleaning or maintenance. Contact with
hot surfaces can cause burns and
serious injury
• Cleaning is recommended for health and safety purposes and to prolong the life of the unit
• DO NOT use abrasive pads or cleaners on the stainless steel or any other metal parts of the unit
• DO NOT use industrial chemical cleaners, fl ammable cleaners, caustic based cleaners or bleaches and bleaching agents, as many will
damage the metals and plastics used on this unit
• DO NOT remove any screws and/or panels for cleaning (unless directed)
• This unit is NOT waterproof, DO NOT hose, DO NOT pour water directly onto the unit, DO NOT immerse in water
• Stainless steel exhibits good resistance to corrosion however, if not properly maintained stainless steel can rust and/or corrode
• Any sign of mild rust and/or corrosion should be thoroughly cleaned with warm soapy water and dried as soon as possible
• NEVER use abrasive pads or cleaners for cleaning
• All metal surfaces should be checked while cleaning for damage, scuffs or scrapes as these can lead to rust and further damage to the
product
• Mild rust and/or corrosion can be treated with a commercial cleaning agent that contains citric/oxalic/nitric/phosphoric acid.
DO NOT use cleaning agents with chlorides or other harsh chemicals as this can cause corrosion.
After treatment, wash with warm (not hot) soapy water and dry thoroughly
• Thoroughly wipe the surfaces dry after cleaning. DO NOT let water pool on the unit. Check crevices and folds for pooling and dry
thoroughly
• When using, ensure all liquids and moisture is cleaned up straight away.
Food liquids such as juices from vegetables and fruits should not be left on preparation surfaces
• DO NOT leave items on the stainless steel such as cutting boards, rubber mats and bottles
• To protect the polished surface of the stainless steel, it should be dried using a clean dry soft cloth. A light oil can be applied to enhance
the stainless steel surface, using a clean cloth apply the oil in the same direction as grained polished fi nish
• Some commercial stainless steel cleaners can leave residue or fi lm on the metal; this may trap fi ne particles of food on the surface,
thus deeming the surfaces not food safe
5.1.1 Cleaning Schedule
• Regular cleaning is recommenced for the unit. This will help to maintain and prolong the efficiency of the unit
5.1.2 Materials Required
• Stainless Cleaner
• Non Abrasive Cleaning pad
• Clean Sanitised Cloth
• Paper Towel
• Warm Soapy Water
• Appropriate PPE (Personal Protective Equipment)
5.1 Cleaning
5.1.3 General Information
5.1.4 Corrosion Protection
5.1.5 Surface Finish
Page 13
Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz
5.1.6 Cleaning Procedure
1. Isolate the unit from the power supply
2. Using a good quality nylon brush remove crumbs and small food items
3. Wipe clean using a cloth dampened (not wet) with clean warm water until all soil has been removed
4. Using a clean sanitised cloth, thoroughly wipe the stainless steel and metal parts dry. Do NOT let water pool on the unit. Check crevices
and folds
5.1.7 Cleaning Procedure - External Surfaces
1. Isolate the unit from the power supply
2. Wearing Personal Protective Equipment (PPE), apply Stainless Cleaner with the Cleaner pad to the external surfaces
3. Scrub any baked on soil with the cleaner pad in the same direction as grained polish
4. Wipe clean using a cloth dampened with clean warm water until all Stainless Cleaner and soil has been removed
5. Using a clean sanitised cloth, thoroughly wipe the stainless steel and metal parts dry. Do NOT let water pool on the unit. Check crevices
and folds
5.0 Cleaning and Maintenance
Page 14
Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz
Problem Possible Causes Possible Corrective Action
Unit won’t turn on
Unit is not plugged into a suitable power point Plug unit in
Power switch is in the “Off” position Change the power switch to the “ON” position
Power Point is faulty Contact the Stoddart service department
Unit is overheating Airflow blockage Clear dirt / dust from fan guard and/ or clear all air vents around the unit
of any obstructions
Fan not working Contact the Stoddart service department
Unit is not heating Elements not working Contact the Stoddart service department
Temp switch / Computer board not working Contact the Stoddart service department
Product is burning Temperature set too high Adjust temperature settings as required
Product is undercooked Temperature is set too low Adjust temperature settings as required
WARNING
Technician tasks are only to be completed by qualied service
people. Check faults before calling service technician.
• If any faults/issues occur with the unit, follow the below troubleshooting procedures
• If the troubleshooting procedures do not correct the problem, contact the Stoddart Service Department
5.0 Cleaning and Maintenance
5.2 Troubleshooting
www.stoddart.com.au
International
Sales
Tel: +617 3440 7600
Email: [email protected]
Service / Spare Parts
Tel: +617 3440 7600
Email: [email protected]
Email: [email protected]
Service Request
www.stoddart.co.nz
New Zealand Business Number: 6837694
New Zealand
Sales
Tel: 0800 79 1954
Email: [email protected]
Service / Spare Parts
Tel: 0800 935 714
Email: [email protected]
Email: [email protected]
Service Request
www.stoddart.com.au
Australian Business Number: 16009690251
Australia
Sales
Tel: 1300 79 1954
Email: [email protected]
Service / Spare Parts
Tel: 1300 307 289
Email: [email protected]
Email: [email protected]
Service Request
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
Woodson W.GTQI8S Instrukcja obsługi
- Typ
- Instrukcja obsługi
- Ten podręcznik jest również odpowiedni dla
w innych językach
- English: Woodson W.GTQI8S User manual
