A guide on the use, care and maintenance
of your quality Woodson Starline product
Models:
W.CVS.SE.20 / W.CVS.M.25x / W.CVS.M2.25x
W.CVS.L.30x / W.CVS.L2.30x
Snack Master Series 20 / 25 / 30
Digital Controller
SPECIFICATION, INSTALLATION
AND OPERATION MANUAL
READ ALL INSTRUCTIONS BEFORE USE
Revision: B - 24/07/2020
Page Intentionally Left Blank
Page 1
Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz
Page 2
Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz
Introduction
Your New Woodson Product . . . . . . . . . . . . . . . . . . 3
Australia and New Zealand Warranty . . . . . . . . . . . . . . 4
Warranty Period
Warranty Registration
General Precautions . . . . . . . . . . . . . . . . . . . . . . 4
Installation
Product Overview . . . . . . . . . . . . . . . . . . . . . . . . 5
Setting Up . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Handling
Unpacking
Positioning
Disposal
Electrical Connection . . . . . . . . . . . . . . . . . . . . . . 7
Information
Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . 8
W.CVS.M.25 / W.CVS.L.30
Specification
Technical Specifications . . . . . . . . . . . . . . . . . . . . 9
W.CVS.SE.20
W.CVS.M.25
W.CVS.L.30
Operation
Operating Instructions . . . . . . . . . . . . . . . . . . . . .11
Control Panel information
Operation Adjustments
Cross Flow Air/Ventilation
Switching Unit Off
Cleaning and Maintenance
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
General Information
Corrosion Protection
Surface Finish
Cleaning Schedule
Materials Required
Cleaning Procedure - Conveyor and Crumb Tray
Cleaning Procedure - External Surfaces
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . .15
Page 3
Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz
Introduction
Carefully read this instruction booklet, as it contains important advice for safe installation, operation and maintenance.
Keep this booklet on hand in a safe place for future reference by other operators or users.
Stoddart design, manufacture & distribute Food Service Equipment (appliances) exclusively for the commercial market.
This appliance is not designed nor intended for household or domestic use & must not be used for this purpose.
This product is intended for commercial use, and in line with Australian electrical safety standards the following warnings are provided:
• This product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision or instruction concerning the use of the product by a person
responsible for their safety. Children should be supervised to ensure that they do not play with the product
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualifi ed persons in order to avoid
a hazard
The manufacturer and distributor cannot be held responsible or liable for any injuries or damages of any kind occurred to persons,
units or others, due to abuse and misuse of this unit in regards to installation, removal, operation, servicing or maintenance, or lack of
conformity with the instructions indicated in this documentation.
Disclaimer
All units made by the manufacturer are delivered assembled, where possible, and ready to install. Any installation, removal, servicing,
maintenance and access or removal of any parts, panels or safety barriers that is not permitted, does not comply in accordance to this
documentation, or not performed by a TRAINED AND AUTHORISED SPECIALIST will result in the
IMMEDIATE LOSS OF THE WARRANTY.
The manufacturer cannot be held responsible or liable for any unauthorized modifi cations or repairs. All modifi cations or repairs must
be approved by the manufacturer in writing before initiating. All modifi cations or repairs performed to this unit must be performed at all
times by a TRAINED AND AUTHORISED SPECIALIST.
Thank you for choosing this quality Woodson product.
All Woodson products are designed and manufactured to meet the needs of food service professionals. By caring for and maintaining your
new Woodson product in accordance with these instructions, will provide many years of reliable service.
Stoddart is a wholly Australian owned company, which manufactures and/or distributes a comprehensive range of food service equipment for
kitchens, food preparation and presentation. Stoddart products are manufactured and/or engineered in Australia to provide excellent results
whilst offering value-for-money, ease-of-use and reliability.
Your New Woodson Product
Page 4
Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz
Introduction
Carefully read this instruction booklet, as it contains important advice for safe installation, operation and maintenance.
Keep this booklet on hand in a safe place for future reference by other operators or users.
Stoddart design, manufacture & distribute Food Service Equipment (appliances) exclusively for the commercial market.
This appliance is not designed nor intended for household or domestic use & must not be used for this purpose.
This product is intended for commercial use, and in line with Australian electrical safety standards the following warnings are provided:
• This product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision or instruction concerning the use of the product by a person
responsible for their safety. Children should be supervised to ensure that they do not play with the product
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualifi ed persons in order to avoid
a hazard
The manufacturer and distributor cannot be held responsible or liable for any injuries or damages of any kind occurred to persons,
units or others, due to abuse and misuse of this unit in regards to installation, removal, operation, servicing or maintenance, or lack of
conformity with the instructions indicated in this documentation.
Disclaimer
All units made by the manufacturer are delivered assembled, where possible, and ready to install. Any installation, removal, servicing,
maintenance and access or removal of any parts, panels or safety barriers that is not permitted, does not comply in accordance to this
documentation, or not performed by a TRAINED AND AUTHORISED SPECIALIST will result in the
IMMEDIATE LOSS OF THE WARRANTY.
The manufacturer cannot be held responsible or liable for any unauthorized modifi cations or repairs. All modifi cations or repairs must
be approved by the manufacturer in writing before initiating. All modifi cations or repairs performed to this unit must be performed at all
times by a TRAINED AND AUTHORISED SPECIALIST.
Thank you for choosing this quality Woodson product.
All Woodson products are designed and manufactured to meet the needs of food service professionals. By caring for and maintaining your
new Woodson product in accordance with these instructions, will provide many years of reliable service.
Stoddart is a wholly Australian owned company, which manufactures and/or distributes a comprehensive range of food service equipment for
kitchens, food preparation and presentation. Stoddart products are manufactured and/or engineered in Australia to provide excellent results
whilst offering value-for-money, ease-of-use and reliability.
• All units MUST be installed according to the procedures stated in the installation section of this manual
• In the case of new personnel, training is to be provided before operating the equipment
• DO NOT use this unit for any other purpose than its intended use
• DO NOT store explosive substances such as aerosol cans with a fl ammable propellant in or near this unit
• Keep fi ngers out of “pinch point” areas
• Unit is not waterproof DO NOT use jet sprays, hoses or pour water over/on the exterior of the unit
• Only use this unit with voltage specifi ed on the rating label
• Do NOT remove any cover panels that may be on the unit
• DO NOT use sharp objects to activate controls
• DO NOT use sharp objects to remove ice from the unit
• If any fault is detected, refer to troubleshooting
• The manufacturer declines any liability for damages to persons and/or things due to an improper/wrong and/or unreasonable use of the
machine
• Only specifi cally trained/qualifi ed Technicians (Stoddart, one of our service agents, or a similarly qualifi ed persons) should carry out any
and all repairs, maintenance and services
When using any electrical unit, safety precautions must always be observed.
Our units have been designed for high performance. Therefore, the unit must be used exclusively for the purpose for which it has been designed.
General Precautions
Warranty Registration
Warranty Period
Australia and New Zealand Warranty
To register your new product, go to the Stoddart warranty page: http://www.stoddart.com.au/warranty-registration
Stoddart 12 month on-site parts and labour warranty (terms and conditions apply), from the time of purchase.
To view or download the warranty terms and conditions visit: http://www.stoddart.com.au/warranty-information
Warranty & Registration
Page 5
Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz
Installation
Conveyor
Exit Rack
Control Panel
Height Adjustment
Rating Plate
CAUTION
Surface is Hot
Product Overview
Page 6
Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz
Installation
Air Vent
INFORMATION
Do not cover Air Vents.
Allow a minimum air gap of 100mm around the unit.
Setting Up
Handling
Unpacking
Positioning
Disposal
• Use suitable means to move the unit;
- For smaller items use two people
- For large items a fork lift, pallet trolley or similar (the forks should reach completely beneath the pallet)
• Check the unit for damage before and after unpacking. If unit is damaged, contact the distributor and manufacturer
• Should any item have physical damage, report the details to the freight company and to the agent responsible for the dispatch within
seven (7) days of receipt. No claims will be accepted or processed after this period
• The unit is supplied fully assembled
• Remove all protective plastic film, tapes, ties and packers before installing and operating
• Clean off any remaining residue from the interior/exterior of the unit using a clean cloth dampened with warm soapy water
• Choose an area that is well ventilated and provides access for future maintenance
• Place the unit on a level stable work surface capable of supporting its weight
• Do not position the unit in:
- Wet areas
- Near heat and/or steam sources
- Near flammable substances
• Allow an air gap between the unit and other objects or surfaces. A minimum gap of 100mm from all sides is recommend for normal
operational use (if the unit is near any heat sensitive material we suggest you allow additional space)
• Please consult national and local standards to ensure that your unit is positioned in accordance with any existing requirement
WARNING
Improper installation, adjustments, alterations, service or
maintenance can cause property damage, injury or death.
100mm
APPLIANCE
100mm
100mm
Front
• At the end of the appliance’s working life, make sure it is scrapped & components recycled properly
• Current environmental protection laws in the state/country of use must be observed
• Doors must be removed before disposal (if applicable)
• Power supply cable must be removed before disposal
• For further information on the recycling of this product, contact the local dealer/agent or the local body responsible for waste disposal
Page 7
Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz
Single Phase Units 1Ø + N + E:
• W.CVS.SE.20 (20A 1Ø)
- Supplied with 2 metre lead and 20 Amp single phase 3 round pin capture plug for fi tting on site to a suitable industrial style outlet
- It is highly recommended that the W.CVS.SE.20 is connected to a suitably rated circuit with a minimum 4mm² cable
• W.CVS.M.25, W.CVS.M2.25 (25A 1Ø)
- Supplied with 2 metre lead for appropriate hard wiring on site by a qualifi ed electrician
- Optional factory fi tted plug is available (W.CVS.PL32)
• W.CVS.L.30, W.CVS.L2.30 (30A 1Ø)
- Supplied with 2 metre lead for appropriate hard wiring on site by a qualifi ed electrician
- Optional factory fi tted plug is available (W.CVS.PL32)
On-site Connection:
• The electrical supply must comply with the rating plate data
• Ensure that the machine is connected to a suitably rated power source
• Disconnection must be incorporated in the fi xed wiring in accordance with the wiring rules
This unit must be installed in accordance with AS/NZS 60335.1
Some procedures in this manual require the power to the equipment to be turned off and
isolated. Turn the power OFF at the power point and unplug the power supply lead by the plug
body. If the power point is not readily accessible turn the equipment off at the isolation switch
or the circuit breaker in the switchboard. Attach a yellow “CAUTION-DO NOT OPERATE” tag.
This must be performed where relevant unless the procedures specify otherwise.
FAILURE TO DO SO MAY RESULT IN ELECTRIC SHOCK.
WARNING
Notes:
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualifi ed persons in order to avoid a
hazard. Please contact Stoddart for parts and we will advise how to do this in order to avoid any electrical hazard
• The power cable should be dry and/or isolated from moisture or water
Electrical Connection
Information
Installation
Page 8
Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz
Installation
ActN
CONTACTOR
THERMOSTAT
PC BOARD
CONTACTOR
SWITCH
MOTOR
FAN
SOLID STATE
RELAY
TOP ELEMENTS
BOTTOM ELEMENTS
TRANSFORMER
SOLID STATE
RELAY
E
See table for Eng. Mode config. file
ENCODER
DATE
NAME
PART No:
DWG No:
This drawing remains the property of Tom Stoddart Pty Ltd ABN 16 009 690 251 & cannot be reproduced without prior permission.
Dwg. Issue
DESCRIPTION:
A3
www.stoddart.com.au
REV/VER REVISED BY DATE REVISION DESCRIPTION STATUS
C1 JORDAN HOLDER 31/01/18 START REVISION C FOR MANUFACTURE
C2 JORDAN HOLDER 28/02/18 ADDED CONTACTOR CONNECTION NAMES FOR MANUFACTURE
DRAWN
APPV'D
G:\03_Engineering\Woodson\W-CVx Conveyor Toasters & Ovens\06_Electrical Diagrams\Common Diagrams\DC Motor Units - Snackmaster\W-CVS DC E01
C2.dwg
16/02/2018
Jordan Holder
---- ----
W-CVS DC
Woodson; Starline; Snackmaster w/ Digital Controls Electrical Diagram
1
SHEET 1 OF 1
W-CVS DC E01 C2
Common Spare Parts
Description
Contactor
Switch
Fan
Solid State Relay
PC Board
Thermostat
Transformer
Encoder
Motor
Part Number
CMEL.0093
CMEL.1354
CMEL.1957
CMEL.2161
CMEL.2131
CMEL.1963
CMEL.1975
CMEL.2159
CMMG.0006
Probe CMEL.2027
Element Spare Parts
Model No.
W.CVS.M.25
Part Number
CMEL-1985
W.CVS.M.25L
W.CVS.M2.25
W.CVS.M2.25L
W.CVS.L.30
W.CVS.L.30L
W.CVS.L2.30
W.CVS.L2.30L
CMEL-1988
Configuration Files
Model No.
W.CVS.M.25
Config. File
#4
W.CVS.M.25L
W.CVS.M2.25
W.CVS.M2.25L
W.CVS.L.30
W.CVS.L.30L
W.CVS.L2.30
W.CVS.L2.30L
#5
Wiring Diagram
W.CVS.M.25 / W.CVS.L.30
Page 9
Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz
465
505
375
77
628
300 300
308
288
600
435
356
435
1200
85
Chamber
Specification
375
1000
528
445
315
375
308
288
465
77
300500200
305
Technical Specifications
W.CVS.SE.20
W.CVS.M.25
Specifications
Model W.CVS.SE.20
Height 465mm
Width 1000mm
Depth 445mm
Power 4.8kW
20A 3Ø + N + E
Specifications
Model W.CVS.M.25
Height 465mm
Width 1200mm
Depth 505mm
Power 6.0kW
25A 3Ø + N + E
Page 10
Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz
465
85
610
480
540
450
540
1200
628
300 300
308
288
600
Specification
W.CVS.L.30
Specifications
Model W.CVS.L.30
Height 465mm
Width 1200mm
Depth 610mm
Power 7.2kW
30A 3Ø + N + E
Page 11
Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz
Operation
Operating Instructions
Belt Speed “Time”:
Elements “Top / Bottom”:
Temperature “Temp”:
Notes:
Control Panel information
Upon setting up your equipment, the following steps must be followed to setup the timer and temperature:
When this unit is initially switched on, the display will show pre-set factory settings.
• The time is controlled via the top two ˅ ˄ buttons. The display shows the set time as (MMSS)
• To change the time settings, Press and hold the time ˅ ˄ buttons for a minimum of 2 seconds to adjust in 30 second increments. For
more precise adjustment press and release to adjust in 5 second increments
• The time in the chamber is from when the product enters the chamber to when it exits the chamber
• The top and bottom elements are controlled via the top and bottom ˅ ˄ buttons. The display will show numbers between 0-99 which
indicates a percentage (%) value of the effective power sent to each element.
For example: If the top element is set at 99% and the bottom element is set at 50%, there will be approximately double the energy
coming from the top element as there is coming from the bottom element
• To change the element settings, press the top or bottom ˅ ˄ buttons. Each press will move the number by 1
• The temp is controlled via the temp ˅ ˄ buttons. The display will show numbers between 50-350 this is °C
• To change the temp settings, press the temp ˅ ˄ buttons. The temperature can be set between 50°C-350°C adjusted in 5°C
increments. The display will read the new adjusted temperature in the oven after approximately 10 seconds
• If the temp set-point is higher than the element percentages can reach, then the elements will pulse at the top and bottom element %
setting and the unit will become a radiant cooker. For most cooking, this will produce less consistent results
• For example: Temp set to 350°C, top element set to 80% and bottom element set to 50%. There would not be enough energy running to
the elements to reach 350°C. This would cause the top element to pulse at exactly 80% and the bottom at pulse at exactly 50%
• It is not recommended to run the unit at 350°C
Time in Chamber
Start Finish
Page 12
Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz
Operation
1. Turn the unit on at the “Power Switch”
2. Adjust the belt speed “Time” to the required setting
3. Set the “Top” element to 90%
4. Set the “Bottom” element to 99%
5. Set the “Temp” to 250°C
6. Place food on the conveyor
7. Adjust as required: increase/decrease the conveyor “Time”, “Top” element and “Bottom” element and/or “Temp”. Repeat this
process until the desired results have been achieved
8. Once satisfied with the results, record the settings for future reference (Refer to our recipe guide for ideas and base settings)
9. Repeat this process for different foods
• For best results there needs to be no cross-flow air/ventilation (no external fans pointed at the unit). This affects the air curtain at
entrance and exit of the oven chamber, causing temperature instability in the unit.
• Adjust the height of the oven chamber entrance and exit guard to a minimum height above the food product to minimise external
airflow entering the unit
• Do not unplug the unit for at least 30 minutes after the unit is switched. The fan runs on an internal thermostat which keeps the
internals cool and helps to remove excess heat from elements and oven chamber
Operation Adjustments
Cross Flow Air/Ventilation
Switching Unit Off
Notes:
• After 60 seconds the settings will save to the control memory. The unit will now show these settings at start up
• It is recommended to time the belt speed from when the food item starts to enter the oven to when it starts to come out. This is the
time the belt takes to pass through the oven
Oven Chamber Guard
Thumb Screw
Page 13
Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz
Cleaning and Maintenance
Cleaning
IMPORTANT
Threaded fasteners can loosen in service.
Regular inspection and adjustment
should be carried out as required
WARNING
This unit is NOT waterproof, do NOT
hose. DO NOT pour water directly onto
the unit. DO NOT immerse in water
IMPORTANT
Some commercial stainless steel
cleaners leave residue or fi lm on the
metal that may entrap fi ne particles of
food, deeming the surface not
FOOD SAFE
WARNING
Wait until the unit has cooled to a safe
temperature before undertaking any
cleaning or maintenance. Contact with
hot surfaces can cause burns and
serious injury
• Cleaning is recommended for health and safety purposes and to prolong the life of the unit
• Do NOT use abrasive pads or cleaners on the stainless steel or any other metal parts of the unit
• Do NOT use industrial chemical cleaners, caustic based cleaners or bleaches and bleaching agents, as many will damage the metals
and plastics used on this unit
• Do NOT remove any screws and/or panels for cleaning (unless directed)
• This unit is NOT waterproof, do NOT hose, do NOT pour water directly onto the unit, do NOT immerse in water
• Stainless steel exhibits good resistance to corrosion however, if not properly maintained stainless steel can rust and/or corrode
• Any sign of mild rust and/or corrosion should be thoroughly cleaned with warm soapy water and dried as soon as possible
• NEVER use abrasive pads or cleaners for cleaning
• All metal surfaces should be checked while cleaning for damage, scuffs or scrapes as these can lead to rust and further damage to the
product
• Mild rust and/or corrosion can be treated with a commercial cleaning agent that contains citric/oxalic/nitric/phosphoric acid.
Do NOT use cleaning agents with chlorides or other harsh chemicals as this can cause corrosion.
After treatment, wash with warm (not hot) soapy water and dry thoroughly
• Thoroughly wipe the surfaces dry after cleaning and do NOT let water pool on the unit. Check crevices and folds for pooling
• When using, ensure all liquids and moisture is cleaned up straight away.
Food liquids such as juices from vegetables and fruits should NOT be left on preparation surfaces
• Do NOT leave items on the stainless steel such as cutting boards, rubber mats and bottles
• To protect the polish, stainless steel should be dried by wiping a dry soft cloth in the same direction as grained polished fi nish
• For NON-food contact surfaces, a light oil can be wiped on the surfaces with a cloth to enhance the stainless steel surface.
Wipe in the direction of the grain
• Some commercial stainless steel cleaners can leave residue or fi lm on the metal; this may trap fi ne particles of food on the surface,
thus deeming the surfaces not food safe
General Information
Corrosion Protection
Surface Finish
Page 14
Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz
Materials Required
• Stainless Cleaner
• Non Abrasive Cleaning pad
• Clean Sanitised Cloth
• Paper Towel
• Container of warm water
• Nylon Brush
• Appropriate PPE (Personal Protective Equipment)
Cleaning Procedure - Conveyor and Crumb Tray
1. Isolate from the power supply
2. Using a good quality nylon brush remove crumbs and small food items from the conveyor. (Switch the unit on to move the conveyor
forward, then switch off)
3. Wipe clean using a cloth dampened (not wet) with clean warm water until all soil has been removed. (Switch the unit on to move the
conveyor forward, then switch off)
4. Empty and clean the crumb tray. This should be done on a regular basis
Note: In some areas, particularly seaside environments, stainless steel can be subject to surface discolouration or “tea staining”.
This can be removed with an appropriate cleaning agent which contains 10% sodium citrate. Ask your supplier of cleaning chemicals for a
suitable brand.
Cleaning Procedure - External Surfaces
1. Isolate from the power supply
2. Wearing Personal Protective Equipment (PPE), apply Stainless Cleaner with the Cleaner pad to the external surfaces
3. Scrub any baked on soil with the cleaner pad in the same direction as grained polish
4. Wipe clean using a cloth dampened with clean warm water until all Stainless Cleaner and soil has been removed
5. Using a clean sanitised cloth, thoroughly wipe the stainless steel and metal parts dry. Do NOT let water pool on the unit. Check crevices
and folds
Cleaning Schedule
• Daily cleaning is required for the oven conveyor, crumb tray and external surfaces. This will help to maintain and prolong the efficiency
of your oven
• The unit should be cleaned at the end of each work day
Cleaning and Maintenance
Page 15
Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz
Troubleshooting
Task Type - (O) = Operator
(T) = Technician Task
WARNING
Technician tasks are only to be completed by qualied service
people. Check faults before calling service technician.
Problem Possible Causes Task Possible Corrective Action
Unit won’t turn on
Unit is not plugged into a suitable power point O Plug unit in
Power switch is in the “Off” position O Change the power switch to the “ON” position
Power Point is faulty T Arrange a qualified Technician to repair the power point
Isolator Switch is “Off” OTurn Isolator Switch “On”
Conveyor not turning on
Conveyor Motor faulty T Lubricate / replace conveyor motor
Conveyor speed dial not responding T Replace speed dial / Computer board
(whichever is applicable)
Bearings Worn T Replace Gear Head
Conveyor chain binds up in
operation
Sprocket worn T Replace sprocket
Belt loose T Remove a chain link
Foreign object in belt ORemove foreign object from belt
Unit is overheating Airflow blockage O Clear dirt / dust from fan guard and/ or clear all air vents
around the unit of any obstructions
Fan not working T Replace fan
Unit is not heating
Elements not working T Replace Elements as required
Temp switch / Computer board not working T Replace switch / Computer board
(whichever is applicable)
Solid State Relay contactor failed T Replace Solid State Relay contactor
Inconsistent cooking of Product
Speed too slow/fast O Adjust speed settings as required
Element % too low/high O Adjust element settings as required
Temperature set too low/high O Adjust temperature settings as required
Cross flow air/ventilation O
Move any fans away from unit
Adjust height of entrance and exit oven chamber guard
to minimise external airflow entering the unit
Inconsistent quantities of ingredients for same
product.
Frozen or thawed.
Placement on conveyor varies
O
Control quantities of product used
Use different settings fo frozen and thawed
Place product in the same location
Elements not working T Replace Elements as required
• If any faults/issues occur with the unit, follow the below troubleshooting procedures
• If the troubleshooting procedures do not correct the problem, contact the Stoddart Service Department
Cleaning and Maintenance
Page Intentionally Left Blank
Page 16
Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz
Page 17
Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz
Page 18
Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz
www.stoddart.com.au
International
Sales
Tel: +617 3440 7600
Email: [email protected]
Service / Spare Parts
Tel: +617 3440 7600
Email: [email protected]
Email: [email protected]
www.stoddart.co.nz
New Zealand Business Number: 6837694
New Zealand
Sales
Tel: 0800 79 1954
Email: [email protected]
Service / Spare Parts
Tel: 0800 935 714
Email: [email protected]
Email: [email protected]
www.stoddart.com.au
Australian Business Number: 16009690251
Australia
Sales
Tel: 1300 79 1954
Email: [email protected]
Service / Spare Parts
Tel: 1300 307 289
Email: [email protected]
Email: [email protected]
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
