F F BIS-411 1R1Z Instrukcja obsługi

BIS-411 1R1Z
Marka
F F
Model
BIS-411 1R1Z
Typ
Instrukcja obsługi
- 1 -
BIS-411 1R1Z 24 V
Bistable relay
Electronic bistable pulse relay BIS-411 1R1Z allows switching on
or off the lighting or other device from several different points
by parallel connected, momentary (bell) control switches.
The receiver is switched on after a current pulse caused by pres-
sing any momentary (bell) button connected to the relay. After
the next pulse, the receiver will be switched off. The relay does
not have a "memory" of the contact position, which means in
the event of a power failure and its subsequent return, the relay
contact will be set to "off". This prevents the controlled receivers
from being switched on automatically without supervision after
a prolonged power failure.
Purpose
Functioning
F&F Filipowski L.P.
Konstantynowska 79/81, 95-200 Pabianice, POLAND
phone/fax (+48 42) 215 23 83 / (+48 42) 227 09 71
www.fif.com.pl; e-mail: biuro@fif.com.pl
Do not dispose of this device in the trash along with other waste! According to the Law on
Waste, electro coming from households free of charge and can give any amount to up to
that end point of collec� on, as well as to store the occasion of the purchase of new equip-
ment (in accordance with the principle of old-for-new, regardless of brand). Electro thrown
in the trash or abandoned in nature, pose a threat to the environment and human health.
- 2 -
1. Disconnect the power supply.
2. Fix the relay on a rail in the control box.
3. Connect the power wires to terminals 1-3: for AC voltage, any
polarity; for DC voltage: "+" to terminal 3, "–" to terminal 1.
4. Momentary switches connected in parallel, connect to termi-
nal 6 and to the wire to which terminal 3 is connected.
5. Connect the powered receiver in series to terminals 7-9 or
10-12.
Mounting
Wiring diagram
- 3 -
BIS-411 1R1Z can’t work with backlit buttons.
1-3 power supply of the relay 9÷30 V AC/DC
6 control input
7-9 output – NC contact (passive)
10-12 output – NO contact (active)
Different supply voltages for the relay and receiver
Example of connection
- 4 -
The maximum total backlight current of all connected
buttons must not exceed 5 mA.
power supply 9÷30 V AC/DC
contact separated 1×NO, 1×NC
maximum load current (AC-1) 2×8 A
control pulse current 5 mA
activation delay 0,1÷0,2 s
power supply indication green LED
activation indication red LED
power consumption
standby 0.15 W
on 0.6 W
terminal 2.5 mm² screw terminals
tightening torque 0.4 Nm
working temperature -25÷50°C
dimensions 1 module (18 mm)
mounting on TH-35 rail
ingress protection IP20
Technical data
- 5 -
tungsten halogen fluorescent energy-saving LED
1000 W 600 W 500 W 250 W 100 W
The above data are indicative and will heavily depend on the
design of a specific receiver (that is especially important for
LED bulbs, energy-saving lamps, electronic transformers and
pulse power supply units), switching frequency and operating
conditions.
For more information visit: www.fif.com.pl.
The F&F products are covered by a warranty of the 24 months
from the date of purchase. Effective only with proof of purchase.
Contact your dealer or directly with us.
F&F Filipowski L.P. declares that the device is in conformity
with the essential requirements of The Low Voltage Directive
(LVD) 2014/35/EU and the Electromagnetic Compatibility (EMC)
Directive 2014/30/UE.
The CE Declaration of Conformity, along with the references to
the standards in relation to which conformity is declared, can be
found at www.fif.com.pl on the product page.
Power table
Warranty
CE declaration
E230912
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

F F BIS-411 1R1Z Instrukcja obsługi

BIS-411 1R1Z
Marka
F F
Model
BIS-411 1R1Z
Typ
Instrukcja obsługi
ściągnij PDF
raport

w innych językach

Powiązane dokumenty

Inne dokumenty