VOLT VSPL-1047-BBZ Instrukcja instalacji

Typ
Instrukcja instalacji
INSTALLATION INSTRUCTIONS
VOLT® Low Voltage Landscape Lighting
VOLT® Solar Flame Integrated LED Brass Path Light (Bronze)
VSPL-1047-BBZ
Specications and product details subject to change without notice.
© Copyright 2022, VOLT® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3700
Help Hotline:
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)
- 1 -
Important: Please Read Before Installation
INSTALLATION INSTRUCTIONS
!
www.voltlighting.com
Important Safety Instructions
!
- 2 -
VOLT® Solar Flame Integrated LED Brass Path Light (Bronze)
VSPL-1047-BBZ
This luminaire is intended for installation in accordance with local codes
and the National Electric Code (NEC). Failure to adhere to these codes and
instructions may result in serious injury, property damage and void the
warranty.
These instructions do not intend to cover all variations in installation,
operation maintenance or mounting situations.
Please note that these solar xtures are equipped with built-in photocells, so
they will not turn on until it is dark enough. These xtures will also require
plenty of sunlight to function properly. It’s best to have the xture in an
area where the sun will get to it at all times throughout the day and where
no ambient lighting will aect the photocell at night. If your xture is not
functioning at night, be sure that the on/o button has been engaged. See
step one for details.
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
Lighted lamp is HOT!
WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.
1. Turn o/unplug and allow to cool before replacing lamp.
2. Lamp gets HOT quickly!
3. Do not touch the hot lens, guard or enclosure.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time. Use a soft cloth. Oil from skin may
damage lamp.
6. Do not operate the luminaire tting with a missing or damaged shield.
SAVE THESE INSTRUCTIONS
[email protected] • 813.978.3700
- 3 -
Product Dimensions
Package Contents
A. (1) Fixture Body
B. (1) Flame LED Lamp
C. (1) 12” Stem
Parts Required (Sold Separately)
A. Mounting Accessory
6.33”
6.89”
INSTALLATION INSTRUCTIONS
www.voltlighting.com
- 4 -
2
Remove Solar Panel
1
VOLT® Solar Flame Integrated LED Brass Path Light (Bronze)
VSPL-1047-BBZ
Install Flame Lamp
Using a screwdriver, loosen the
screws to carefully remove the
solar panel from the xture
body to avoid disconnecting
the wires.
Screw
Solar Panel
Fixture Body
Use ame lamp with correct
wattage and type marked on
xture label.
Align the pins in the bottom
of the ame lamp to holes on
the socket and push the ame
lamp into the socket properly.
CAUTION: Do not exceed
maximum wattage marked on
luminaire label.
Socket
Flame Lamp
[email protected] • 813.978.3700
- 5 -
Install Solar Panel
3
Test Solar Light
4
Align the switch to the slot
on the solar panel and place
the solar panel back onto the
xture body. Secure them
together with previously
removed screws. Hand tighten
until snug with a screwdriver.
Screw
Solar Panel
Switch
Slot
Fixture Body
Place the solar panel of the
xture onto a at opaque
working surface. Push the switch
on the ange “ON” to test the
light source. The lights will turn
on while the switch is on.
Now you can proceed to the next
steps of installation knowing the
xture is in ON mode.
On/Off Switch
ON
Fixture Body
FLAT SURFACE
INSTALLATION INSTRUCTIONS
www.voltlighting.com
- 6 -
VOLT® Solar Flame Integrated LED Brass Path Light (Bronze)
VSPL-1047-BBZ
Install Stake
5
Install Fixture Body
6
Determine the desired location
for mounting the luminaire.
Hammer the stake into the
ground until ange of stake
is ush to grade. To avoid
damage to the stake, place a
board on top of the stake while
hammering.
NOTE: If the ground is hard and
the stake is dicult to install,
make a crosscut in the ground
using a at shovel.
Board
Stake
Soil
Ground
Thread the xture body and
the stem onto the stake and
hand tighten until snug.
Ground
Stem
Fixture Body
Soil
Stake
[email protected] • 813.978.3700
- 7 -
How to Replace Battery
Remove Solar Panel
1
Replace Battery
2
Using a screwdriver, loosen the
screws to carefully remove the
solar panel from the xture
body to avoid disconnecting
the wires.
Screw
Solar Panel
Fixture Body
Remove the battery out of
the battery compartment and
replace it with a new one.
Solar Panel
Battery
Battery
Compartment
Install Solar Panel
3
Align the switch to the slot
on the solar panel and place
the solar panel back onto the
xture body. Secure them
together with previously
removed screws. Hand tighten
until snug with a screwdriver.
Screw
Solar Panel
Switch
Slot
Fixture Body
- 8 -
Specications and product details subject to change without notice.
© Copyright 2022, VOLT® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3700
www.voltlighting.com
IS-VSPL-1047-ver1.pdf
Help Hotline:
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

VOLT VSPL-1047-BBZ Instrukcja instalacji

Typ
Instrukcja instalacji

w innych językach