VOLT VUL-680 Series Installation Instructions Manual

VOLT
Marka
VOLT
Model
VUL-680 Series
Typ
Installation Instructions Manual
VOLT
®
Low Voltage Landscape Lighting
VOLT
®
Forged Brass Underwater Light
VUL-680 Series
INSTALLATION INSTRUCTIONS
Specications and product details subject to change without notice.
© Copyright 2017, VOLT
®
Lighting, Lutz FL USA 33549 • All rights
reserved. [email protected] • 813.978.3700
Help Hotline:
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)
VOLT
®
Forged Brass Underwater Light
VUL-680 Series
Important: Please Read Before Installation
INSTALLATION INSTRUCTIONS
This luminaire is intended for installation in accordance with local codes and the
National Electric Code (NEC). Failure to adhere to these codes and instructions may
result in serious injury, property damage and void the warranty.
These instructions do not intend to cover all variations in installation, operation
maintenance or mounting situation.
1. Make sure that the power is turned OFF before installing or servicing this
luminaire.
2. Use only in ponds and small decorative fountains where person will immerse no
more than their hands and lower arms while the product is energized.
3. DO NOT use in water intended for swimming, wading, immersion or bathing.
4. All installer completed cable connections must be located outside of pond or
fountain.
5. Low voltage circuit must be supplied by a power unit marked as suitable for
supplying submersible luminaires.
6. Power unit must be supplied by a circuit protected by a ground fault circuit
interrupter (GFCI).
7. Maximum depth 18”
8. This luminaire is intended to be used only with a power supply (transformer) rated
maximum of 300 watts (25 AMPS) at 15 volts.
9. Wiring connections must be made with wire connectors that is suitable for outdoor
use.
10. Position the low voltage wire and wire connector so that it is located within 6
inches (15.2 cm) from a building structure, a luminaire or tting.
11. The main low voltage cable is intended for shallow burial - less than 6 inches (152
mm)
12. If additional lengths of low voltage cable is required, please contact www.
voltlighting.com or call 1-813-978-3700.
!
www.voltlighting.com
IMPORTANT SAFETY INSTRUCTIONS
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
Lighted lamp is HOT!
WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.
1. Turn off/unplug and allow to cool before replacing lamp.
2. Lamp gets HOT quickly! Contact only switch/plug when turning on.
3. Do not touch the hot lens, guard or enclosure.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time. Use a soft cloth. Oil from skin may damage lamp.
6. Do not operate the luminaire tting with a missing or damage shield.
SAVE THESE INSTRUCTIONS
!
[email protected] • 813.978.3700
Package Contents
Parts Required
A. (1) Fixture Body
A. (2) Mounting Screw (not included)
B. (2) Washers (not included)
C. (2) Anchors (not included)
Product Dimensions
2.95”
3.50”
3.85”
3.85”
D. (1) MR16 Lamp (sold separately)
E. (1) Transformer (sold separately)
INSTALLATION INSTRUCTIONS
www.voltlighting.com
VOLT
®
Forged Brass Underwater Light
VUL-680 Series
Using a screwdriver, loosen the lock
screws and remove the lens assembly
from the xture body.
Insert the lamp with the correct
wattage and type as marked on the
xture label.
CAUTION: Do not exceed maximum
wattage marked on luminaire label.
NOTE: DO NOT touch lamp with
bare hands. Use soft cloth to
handle lamp.
Remove Lens Assembly
Install Lamp
1
2
Socket
MR16 Lamp
Lens Assembly
Lock Screw
Fixture Body
[email protected] • 813.978.3700
Mount Fixture Body
4
Postion the xture body in a desired
location. Using the slots on the xture
base, mark the two mounting points.
Using the marks, drill holes and insert
the anchors. Place the xture body
onto the anchors. Pass the washers
over the mounting screws and thread
the mounting screws into the anchors
to secure the xture body.
Hand tighten until snug with a
screwdriver.
Mounting Screws
(not included)
Anchors (not
included)
Washer (not
included)
Fixture Body
Install Lens Assembly
3
Place the lens assembly back onto
the xture body and secure with lock
screws. Tighten until snug with a
screwdriver.
Lens Assembly
Lock Screw
Fixture Body
VOLT
®
Forged Brass Underwater Light
VUL-680 Series
INSTALLATION INSTRUCTIONS
www.voltlighting.com
Wire Connection
5
Lay out the supply cable to the transformer. Strip both of the leads
from the luminaire pigtail. Connect the leads from the luminaire
supply cable to the transformer (sold separately).
Fixture
Pigtail
Transformer
(sold separately)
Supply Cable
[email protected] • 813.978.3700
Specications and product details subject to change without notice.
© Copyright 2017, VOLT
®
Lighting, Lutz, FL USA 33549 • All rights
reserved [email protected] • 813.978.3700
www.voltlighting.com
is-VUL-680-ver4.pdf
Help Hotline:
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

VOLT VUL-680 Series Installation Instructions Manual

VOLT
Marka
VOLT
Model
VUL-680 Series
Typ
Installation Instructions Manual
ściągnij PDF
raport

w innych językach

Powiązane dokumenty

Inne dokumenty