AMP Lighting 3601 Series Instrukcja instalacji

Typ
Instrukcja instalacji

Ten podręcznik jest również odpowiedni dla

INSTALLATION & MAINTENANCE GUIDE
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com
AMP
®
Low Voltage Landscape Lighting
AMP
®
Estate Size Path & Area Lights
3601 Series
AMP
®
Estate Size Path & Area Lights
3601 Series
INSTALLATION & MAINTENANCE GUIDE
www.amplighting.com
–2–
Important Safety Instructions: Read Before Installation
!
This luminaire is intended for installation in accordance with local codes
and the National Electric Code (NEC). Failure to adhere to these codes and
instructions may result in serious injury, property damage and void the
warranty.
These instructions do not intend to cover all variations in installation,
operation maintenance or mounting situations.
1. Make sure the power is turned OFF before installing or servicing this
luminaire.
2. WARNING: risk of electrical shock. Install all luminaires 10 feet (3.05M)
or more from pool, spa or fountain.
3. This luminaire is intended to be used only with a power supply
(transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Wiring connections must be made with UL listed wire connectors that are
suitable for outdoor use.
5. Position the low voltage wire and wire connector so that it is located
within 6 inches (15.2 cm) from a building structure, a luminaire or
tting.
6. The main low voltage cable is intended for shallow burial - less than 6
inches (152 mm).
7. If additional lengths of low voltage cable are required, please contact
www.amplighting.com or call 1-813-978-3900.
Important Safety Instructions
!
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
Lighted lamp is HOT!
WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.
1. Turn off/unplug and allow to cool before replacing lamp.
2. Lamp gets HOT quickly! Contact only switch/plug when turning on.
3. Do not touch the hot lens, guard or enclosure.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time. Use a soft cloth. Oil from skin may
damage lamp.
6. Do not operate the luminaire tting with a missing or damaged shield.
SAVE THESE INSTRUCTIONS
[email protected] • 813.978.3900
Product Dimensions
–3–
Package Contents
A. (1) Fixture Body
10.25”
6”
3”
Estate Size Hat featured
on Estate Size Low
Voltage Stem
36”
INSTALLATION & MAINTENANCE GUIDE
–4–
www.amplighting.com
–4–
2
1
AMP
®
Estate Size Path & Area Lights
3601 Series
Remove Stem Top
Install Lamp
Loosen the stem top and remove
it from the top end of the stem.
Stem
Stem Top
Insert the lamp with the correct
wattage and type marked on the
xture label and push rmly into
place.
CAUTION: Do not exceed maximum
wattage marked on luminaire label.
Socket
Lamp
3
Install Stem Top
Thread the stem top onto the
stem and hand tighten until
snug.
Stem Top
Stem
[email protected] • 813.978.3900
–5–
4
5
Install Stake
Remove Cap from Stake
Dig a hole in the ground for the stake. Slide the stabilizer grid onto the
stake and secure with the screws. Place the stake and backll against
the mounting stake.
Stake
Stabilizer
Grid
Ground Level
Stake
Remove the cap from the stake
by loosening the set screws.
Set Screw
Cap
Stake
6
Install Cap to Base
Screw the coupler on the bottom
center of the base and then
thread the cap onto the coupler.
Base
Coupler
INSTALLATION & MAINTENANCE GUIDE
–6–
www.amplighting.com
–6–
7
AMP
®
Estate Size Path & Area Lights
3601 Series
Fixture Installation
Pass the supply wires through the
stake. Attach the cap with the
xture onto the stake and secure
with set screws. Hand tighten until
snug with a screwdriver.
Set Screw
Cap
Stake
Supply Wire
8
Wire Connection
Strip both leads from the luminaire pigtail. Using two wire connectors
(sold separately), connect the leads from the luminaire to the main
supply cable leads.
Pigtail
Main Supply Cable
Wire Connectors
–6––6–
[email protected] • 813.978.3900
–7–
Install/Replace Lamp
9
Install Hat
Place the hat of your choice onto the stem top and secure it with the nial,
or thread the hat of your choice onto the stem top directly. Hand tighten
until snug.
Stem Top
Finial
Hat of your choice
Remove the nial, hat and stem top to expose the lamp and replace it
with the correct wattage and type marked on the xture label. Then,
reinstall the stem top, hat and nial.
IMPORTANT: Lamps must be protected from moisture and dust at all
times. Always reinstall the stem top and hat when removed.
IS-ASM-3601-4-BBZ-ver1.pdf
Specications and product details subject to change without notice.
© Copyright 2019, AMP
®
Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3900
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

AMP Lighting 3601 Series Instrukcja instalacji

Typ
Instrukcja instalacji
Ten podręcznik jest również odpowiedni dla

w innych językach