VOLT Big PAR36 Installation Instructions Manual

VOLT
Marka
VOLT
Model
Big PAR36
Typ
Installation Instructions Manual
VOLT® Low Voltage Landscape Lighting
Big PAR36 Flood Light
INSTALLATION INSTRUCTIONS
Specications and product details subject to change without notice.
© Copyright 2014, VOLT® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3700
Help Hotline:
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)
VOLT® Big PAR36 Flood Light
450 Series
Important: Please Read Before Installation
Important Safety Instructions
INSTALLATION INSTRUCTIONS
This luminaire is intended for installation in accordance with local codes
and the National Electric Code (NEC). Failure to adhere to these codes and
instructions may result in serious injury, property damage and void the
warranty.
These instructions do not intend to cover all variations in installation, oper-
ation maintenance or mounting situation.
1. Make sure that the power is turned OFF before installing or servicing
this luminaire.
2. WARNING: risk of electrical shock. Install all luminaires 10 feet
(3.05M) or more from pool, spa or fountain.
3. This luminaire is intended to be used only with a power supply (trans-
former) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Wiring connections must be made with wire connectors that is suitable
for outdoor use.
5. Position the low voltage wire and wire connector so that it is located
within 6 inches (15.2 cm) from a building structure, a luminaire or
tting.
6. The main low voltage cable is intended for shallow burial - less than 6
inches (152 mm)
7. If additional lengths of low voltage cable is required, please contact
www.voltlighting.com or call 1-813-978-3700.
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
Lighted lamp is HOT!
WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.
1. Turn off/unplug and allow to cool before replacing lamp.
2. Lamp gets HOT quickly! Contact only switch/plug when turning on.
3. Do not touch the hot lens, guard or enclosure.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time. Use a soft cloth. Oil from skin may dam-
age lamp.
6. Do not operate the luminaire tting with a missing or damage shield.
SAVE THESE INSTRUCTIONS
!
!
www.voltlighting.com
Package Contents
Product Dimensions
A. (1) Stake
B. (1) Base
C. (1) Lamp Holder
customersupport@voltlighting.com • 813.978.3700
6 1/2”
2”
4 3/4”
D. (1) Shield with Lens
Install Stake
1
Determine desired location for mounting
luminaire. Hammer stake into ground until
ange of stake is ush to grade. To avoid
damage to stake, place a board on top of
stake while hammering.
NOTE: If ground is hard and stake is difcult
to install, make a crosscut in ground using a
at shovel.
Board
Stake
Soil
Ground
INSTALLATION INSTRUCTIONS
www.voltlighting.com
VOLT® Big PAR36 Flood Light
450 Series
Install Lamp
2
Use a PAR36 lamp, sold separately, with
correct wattage and type as marked on
luminaire label.
Connect supply wires to screws on the
bottom of lamp, tighten until snug with
screwdriver. Push lamp into lamp hold-
er and seat in place.
CAUTION: Do not exceed maximum
wattage marked on luminaire label.
NOTE: DO NOT touch lamp with bare
hands. Use soft cloth to handle lamp.
Install shield with lens to lamp
holder by aligning locking pins on
both of them. Be sure to position
the shield with lens properly in
place.
Install Shield with Lens
3
Lamp Holder
Lamp
Lamp Holder
Shield with Lens
Supply Wire
customersupport@voltlighting.com • 813.978.3700
Install/Replace Lamp
Reverse Step 2 - Step 3 to expose the lamp and replace it with correct
wattage and type marked on luminaire label. Reinstall shield with lens.
IMPORTANT: Halogen lamps must be protected from moisture and dust
at all times. Always re-install shield with lens when moved.
Clear away area in ground at wire-
way slot in top of stake. Align the
wireway slots on base and stake.
Lay luminaire pigtail into wireway
slots and screw luminaire into
stake. Tighten until snug to secure
base.
Install Luminaire to Stake
4
Luminaire
Base
Stake
Pigtail
Wireway Slot
Wire Connection
5
Strip two leads from luminaire pigtail. Using two wire connectors, sold
separately, connect leads from luminaire to main low voltage supply
cable leads.
Pigtail
Main Low Voltage
Supply Cable
Wire Connectors
is-450-ver1.pdf
Specications and product details subject to change without notice.
© Copyright 2014, VOLT® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3700
www.voltlighting.com
Help Hotline:
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

VOLT Big PAR36 Installation Instructions Manual

VOLT
Marka
VOLT
Model
Big PAR36
Typ
Installation Instructions Manual
ściągnij PDF
raport

w innych językach

Powiązane dokumenty

Inne dokumenty