Classic Exhibits VK-1105 Setup Instructions
- Typ
- Setup Instructions
www.classicexhibits.com
Step 1
Page 1 of 3
866.652.2100
© 2013
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX -
General Layout
10’
10’
Plan View
www.classicexhibits.com
Step 2
Page 2 of 3
866.652.2100
© 2013
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - General Setup Instructions
The Tool Typical Connection
Horizontal Inline Connection (remove only one setscrew)
Base Plate Connection Vertical Connection
(remove only two setscrews)
Most Visionary Designs exhibits can be
assembled with the supplied Hex Key Tool.
Occasionally, a flat head screwdriver may
be required.
Most horizontal extrusion connections have a patented expandable lock. This lock inserts into
the groove of an opposing extrusion. Tightening the lock with the Hex Key Tool expands the lock
and creates a strong positive connection.
Remove only (1) setscrew when disassembling. Replace setscrew in
extrusion after assembling it. Before packing, replace setscrew in
extrusion to avoid losing it.
Attach base plate to round or square
vertical extrusion using the bolt provided.
Be careful not to strip the threads.
When vertical extrusions are packed in
portable cases rather than crates or
tubs, they must broken down into
smaller sections which then require
assembly.
Remove only (2) setscrews when
disassembling. Replace setscrews in
extrusion after assembling it. Before
packing, replace setscrews in extrusion
to avoid losing them.
Using Your Setup Instructions
The Visionary Designs Setup Instructions are created specifically for your
configuration. They are laid out sequentially, including an exploded view of
the entire display, and then a logical series of detailed steps to assemble the
main structure and components. We encourage you to study the instructions
before attempting to assemble your exhibit.
Each page reminds you to tighten the setscrews after disassembling your
exhibit to prevent loss of the locks and setscrews (see below in RED).
This is VERY IMPORTANT.
Cleaning and Packing Your Display
1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only
non-abrasive cleaners.
2) When cleaning laminate inserts or countertops, use mild cleansers and a
soft material such as cotton.
3) Keep all display components away from extreme heat and long exposure
to sunlight to avoid warping and fading.
4) Retain all packing material. It will make re-packing much easier and will
reduce the likelihood of shipping damage.
Typical Connection (cont’d)
Numbered Label
Each extrusion contains a numbered label which
corresponds with setup instructions.
The label is located within a groove of the extrusion
(when possible). With Visionary Designs the labels
contain Black numbers unless otherwise specified.
Detail C E liateDD liateDDetail B
Detail A
Setscrews
www.classicexhibits.com
Step 1
Page 1 of 3
866.652.2100
© 2013
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - Backwall Assembly
1
2
2a
3
7a 8a 8b 7a
7b
Profile View
9a 9b
10a 10b
7b
3a
3/3a
4
4a
5
5
6
Item Qty Description
1 2 Oval Base Plate
2/2a 1/1 41.75” S44 Vertical Extrusion
3/3a 1/1 42” GS210 Vertical Extrusion
4/4a 1/1 42” GS210 Vertical Extrusion
5 1 42” S44 Vertical Extrusion
6 1 42” S44 Vertical Extrusion
7a/7b 2/2 22” Z45 Horizontal Extrusion
8a/8b 1/1 30” Z45 Horizontal Extrusion
9a/9b 1/1 30” Z45 Horizontal Extrusion
10a/10b 1/1 30” Z140 Horizontal Extrusion
Steps:
1) Connect verticals [2 & 2a] to baseplates with bolts as shown.
2) Connect upper verticals to lower verticals as shown.
3) Connect horizontals [7a,7b] between vertical assemblies.
4) Connect horizontals [8a,8b], [9a,9b] and [10a,10b] together.
5) Connect horizontal assemblies between vertical assemblies.
1
Velcro:
Top Edge Velcro:
Top Edge
Velcro:
Top Edge
Velcro:
Bottom Edge Velcro:
Bottom Edge
Velcro:
Bottom Edge
Velcro
PR37
Extrusion
Profile
Slide PR37 extrusion into
groove of vertical and tighten
set screw to secure in place.
Profile View
Note: Attaching Graphics
Attach backwall graphics to velcro by wrapping
the graphic over the top of the upper horizontals
and under the bottom of the lower horizontals.
Then secure to velcro down the sides.
Velcro
Velcro
Velcro
www.classicexhibits.com
Step 2
Page 2 of 3
866.652.2100
© 2013
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX -
Ceiling & Header Attachments
12a
13b
12b
14b
14a
11a
13a
11b
Item Qty Description
11a/11b 1/1 29.939” Z31 Horizontal Extrusion
12a/12b 1/1 29.939” Z31 Horizontal Extrusion
13a/13b 1/1 33.122” Z31 Horizontal Extrusion
14a/14b 1/1 12.52” Z31 Vertical Extrusion
Steps:
1) Connect header extrusions [11a,11b,12a,12b,13a,13b,14a,14b] together as shown.
2) Connect ceiling panels together as shown in detail.
3) Attach assembled header to assembled ceiling with bolts as shown.
4) Bolt ceiling panels to top of backwall verticals with bolts.
Attach graphic
to velcro on back
of frame
Connect ceiling pieces
together using bolts
washer and wing nuts
wing
nuts
bolts
Ceiling Attachment
AA
BB
www.classicexhibits.com
Step 3
Page 3 of 3
866.652.2100
© 2013
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX -
Attachments
Item Qty Description
15/15a 4/4 8” Z44 Horizontal Extrusion
Steps:
1) Attach shelf supports [15,15a] to backwall where indicated.
2) Place shelf on top of shelf supports.
3) Attach Literature Racks to verticals as shown in detail.
4) Attach monitor mount to horizontals as shown in detail.
Shelf
Shelf
Shelf
Shelf
Attach connector piece to rack
as shown. Then connect
assembled literature
rack to vertical extrusion.
Literature Rack Attachment
Tighten Lock
to Secure
Monitor Mount Attachment
Attach monitor wall plate to
plate using bolts and wing nuts.
*
*
*
*
**
*
15
15a
15a
15
15
15
15a
15a
www.classicexhibits.com
866.652.2100
© 2013
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #37979 -
Packing Instructions - Case 1 of 2
14b 4
14a
10a
13a
13b
Base Plate
Shelves
(2)
Shelves
(2)
Setup Hardware
Graphics
Monitor Mount
Top View of Each Level
Level 1 Level 2 Level 3 Level 4
3
5(4), 5a(4)
8a,9a,8b,9b
7a(2)
7b(2)
5 6 2a 2 3a 4a
10b
www.classicexhibits.com
866.652.2100
© 2013
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #37979 - Packing Instructions - Case 2 of 2
Ceiling Panel
Ceiling Panel
Top View of Each Level
Level 1 Level 2 Level 3
Ceiling Panel
-
1
-
2
-
3
-
4
-
5
-
6
-
7
Classic Exhibits VK-1105 Setup Instructions
- Typ
- Setup Instructions
w innych językach
- English: Classic Exhibits VK-1105
Powiązane dokumenty
-
Classic Exhibits VK-1048 Setup Instructions
-
-
-
-
-
-
-
-
-