Novus NVIP-1DN5001H/IRH-1P Instrukcja obsługi

U s e r ’s m a n u a l

(short form)

NVIP-1DN5001H/IRH-1P

NVIP-1DN5001H/IRH-1P User’s manual ver.1.0

(short form)

2

IMPORTANT SAFEGUARDS AND WARNINGS

EMC (2004/108/EC) and LVD (2006/95/EC ) Directives

CE Marking

Our products are manufactured to comply with requirements of the following directives and national regulations

implementing the directives:

Electromagnetic compatibility EMC 2004/108/EC.

Low voltage LVD 2006/95/EC with further amendment. The Directive applies to electrical

equipment designed for use with a voltage rating of between 50VAC and 1000VAC as well as

75VDC and 1500VDC.

WEEE Directive 2002/96/EC

Information on Disposal for Users of Waste Electrical and Electronic Equipment

This appliance is marked according to the European Directive on Waste Electrical and Electronic Equipment

(2002/96/EC) and further amendments. By ensuring this product is disposed of correctly, you will help to

prevent potential negative consequences for the environment and human health, which could otherwise be

caused by inappropriate waste handling of this product.

The symbol on the product, or the documents accompanying the product, indicates that this appliance may not be

treated as household waste. It shall be handed over to the applicable collection point for used up electrical and

electronic equipment for recycling purpose. For more information about recycling of this product, please contact

your local authorities, your household waste disposal service or the shop where you purchased the product.

RoHS Directive 2002/95/EC

Out of concern for human health protection and friendly environment, we assure that our products

falling under RoHS Directive regulations, regarding the restriction of the use of hazardous

substances in electrical and electronic equipment, have been designed and manufactured in

compliance with the above mentioned regulations. Simultaneously, we claim that our products have

been tested and do not contain hazardous substances whose exceeding limits could have negative

impact on human health or natural environment

Information

The device, as a part of professional CCTV system used for surveillance and control, is not designed for self

installation in households by individuals without technical knowledge.

Excluding of responsibility in case of damaging data on a disk or other devices:

The manufacturer does not bear any responsibility in case of damaging or losing data on a disk or other devices

during device operation.

WARNING!

PRIOR TO UNDERTAKING ANY ACTION THAT IS NOT DESCRIBED FOR THE GIVEN PRODUCT IN

USER’S MANUAL AND OTHER DOCUMENTS DELIVERED WITH THE PRODUCT, OR IF IT DOES

NOT ARISE FROM THE USUAL APPLICATION OF THE PRODUCT, MANUFACTURER MUST BE

CONTACTED UNDER THE RIGOR OF EXCLUDING THE MANUFACTURER’S RESPONSIBILITY FOR

THE RESULTS OF SUCH AN ACTION.

NVIP-1DN5001H/IRH-1P User’s manual ver.1.0

(short form)

3

IMPORTANT SAFEGUARDS AND WARNINGS

WARNING!

THE KNOWLEDGE OF THIS MANUAL IS AN INDISPENSIBLE CONDITION OF A PROPER

DEVICE OPERATION. YOU ARE KINDLY REQEUSTED TO FAMILIARIZE YOURSELF WITH

THE MANUAL PRIOR TO INSTALLATION AND FURTHER DEVICE OPERATION.

WARNING!

USER IS NOT ALLOWED TO DISASSEMBLE THE CASING AS THERE ARE NO USER

-SERVICEABLE PARTS INSIDE THIS UNIT. ONLY AUTHORIZED SERVICE PERSONNEL

MAY OPEN THE UNIT

INSTALLATION AND SERVICING SHOULD ONLY BE DONE BY QUALIFIED SERVICE

PERSONNEL AND SHOULD CONFORM TO ALL LOCAL REGULATIONS

1. Prior to undertaking any action please consult the following manual and read all the safety and operating

instructions before starting the device.

2. Please keep this manual for the lifespan of the device in case referring to the contents of this manual is

necessary;

3. All the safety precautions referred to in this manual should be strictly followed, as they have a direct

influence on user’s safety and durability and reliability of the device;

4. All actions conducted by the servicemen and users must be accomplished in accordance with the user’s

manual;

5. The device should be disconnected from power sources during maintenance procedures;

6. Usage of additional devices and components neither provided nor recommended by the producer is

forbidden;

7. You are not allowed to use the camera in high humidity environment (i.e. close to swimming pools, bath tubs,

damp basements);

8. Mounting the device in places where proper ventilation cannot be provided (e. g. closed lockers etc.) is not

recommended since it may lead to heat build-up and damaging the device itself as a consequence;

9. Mounting the camera on unstable surface or using not recommended mounts is forbidden. Improperly

mounted camera may cause a fatal accident or may be seriously damaged itself. The camera must be mounted

by qualified personnel with proper authorization, in accordance with this user’s manual.

10. Device should be supplied only from a power sources whose parameters are in accordance with those

specified by the producer in the camera technical datasheet. Therefore, it is forbidden to supply the camera

from a power sources with unknown parameters, unstable or not meeting producer’s requirements;

Due to the product being constantly enhanced and optimized, certain parameters and functions described in the

manual in question may change without further notice. We strongly suggest visiting the www.novuscctv.com

website in order to access the newest manual

Data included in the following user’s manual is up to date at the time of printing. AAT Holding Sp z o.o. holds

exclusive rights to modify this manual. The producer reserves the rights for device specification modification

and change in the design without prior notice.

NVIP-1DN5001H/IRH-1P User’s manual ver.1.0

(short form)

4

TABLE OF CONTENTS ..................................................................................................... 4

1. FOREWORD INFORMATION ................................................................................... ..5

1.1. General Characteristics ........................................................................................ 5

1.2. NVIP-1DN5001H/IRH-1P tech specification ................................................. ...6

1.3. Camera dimension ........................................................................................... ...7

1.4. Package contents ............................................................................................... ...8

2. START-UP AND INITIAL IP CAMERA CONFIGURATION ................................. 9

2.1. Description of connectors and control tools ........................................................ 9

2.2. Cable connectors .................................................................................................. 9

2.3. NVIP-1DN5001H/IRH-1P mounting ................................................................ 10

2.4. Starting the IP camera ........................................................................................ 12

2.5. Initial configuration via the Web browser ......................................................... 13

3. NETWORK CONNECTION UTILIZING WEB BROSWER ................................ 14

3.1. Recommended PC specification for web browser ............................................. 14

3.2. Connection with IP camera via the Internet Explorer ........................................ 14

4. WWW INTERFACE - WORKING WITH IP CAMERA ......................................... 16

4.1. Displaying live pictures. ..................................................................................... 16

5. ELECTRIC CONNECTORS AND ACCESORIES ................................................. 18

5.1. Connecting power supply to the camera. .......................................................... 18

6. RESTORING FACTORY DEFAULTS ..................................................................... 18

6.1. Restoring software factory defaults .................................................................... 18

6.2. Restoring hardware factory defaults in IP cameras ............................................ 19

TABLE OF CONTENTS

NVIP-1DN5001H/IRH-1P User’s manual ver.1.0

(short form)

5

1. FOREWORD INFORMATION

1.1. General Characteristics

Imager resolution: 1.3 fmegapixels

Mechanical IR cut filter

IR operation capability

Min. Illumination from 0,034 lx/F=2.2 , 0 lx (IR on)

Digital Slow Shutter (DSS)

Digital Noise Reduction (DNR)

Lens f=3.6m/F=2.2

Built-in IR LED - 2 pcs., up to 15 m

Privacy zones: 5

Compression: H.264, M-JPEG

Max video processing resolution: 1280x960

Double stream mode: compression, resolution, speed and quality defined individually for each

video stream

RTP/RTSP protocol support for video transmission

Pre & post-alarm functions

Hardware motion detection

Built-in webserver: camera configuration through the website

Wide range of responses to alarm events: e-mail with attachment, saving file on FTP and NAS

server,

Network protocol support : ONVIF (2.2)/Profile S, HTTP, TCP/IP, IPv4/v6, UDP/IP, RTSP,

FTP, DHCP, NTP, PPPoE, SMTP

Software: NMS (NOVUS MANAGEMENT SYSTEM) for video recording, live monitoring,

playback and remote IP devices administration

Degree of protection IP66

Built-in heater

Power supply: 12VDC, PoE (Power over Ethernet)

FOREWORD INFORMATION

NVIP-1DN5001H/IRH-1P User’s manual ver.1.0

(short form)

6

1.2. NVIP-1DN5001H/IRH-1P specification

FOREWORD INFORMATION

NVIP-1DN5001H/IRH-1P

IMAGE

Pick-up Element 1.3 MPX, CMOS imager, 1/3”

Number of Effective Pixels 1280 (H) x 960 (V)

Min. Illumination 0.67 lx/F=2.2 – color mode,DSS OFF

0.034 lx/F=2.2 – color mode,DSS ON

0 lx (IR on) –b/w mode

Digital Slow Shutter (DSS) x5

Digital Noise Reduction (DNR) Yes

LENS

Type Standard, f=3.6/F=2.2

Angle of View (H) 73°

DAY/NIGHT

Type Mechanical IR cut filter

Switch Mode Auto,manual

NETWORK

Stream Resolution 1280 x 960, 1280 x 720 (HD ), 720 x 576 (D1), 640 x 480 (VGA)

640 x 360, 352 x 288 (CIF), 320 x 240 (QVGA), 176 x 144 (QCIF)

Frame Rate 30 fps for each resolution

Multistreaming Mode 2 streams

Video/Audio Compression H.264, M-JPEG, M-JPEG

Network Protocols Support ONVIF (2.2)/Profile S, HTTP, TCP/IP, IPv4/v6, UDP/IP, RTSP, FTP,

DHCP, NTP, PPPoE, NTP, SMTP

PC Software

NOVUS NMS, Internet Explorer, Google Chrome, Opera, Mozilla, Firefox

OTHER FUNCTIONS

OSD IE browser, Polish, English, Russian, other

Privacy Zones 5

Motion Detection Yes

Prealarm/Postalarm 5MB /0s - 86400s

System Reaction to Alarm Events E-mail with attachment, saving file on: FTP/NAS server

IR LED

Number 2

Range 15 m

Angle 90°

INTERFACES

Network Interface 1 x Ethernet - RJ-45 interface, 10/100 Mbit/s

INSTALLATION PARAMETERS

Dimensions (mm) 70 (W) x 63 (H) x 90 (L)

Weight 473 g

Enclosure Aluminium, white

Power Supply PoE,12 VDC

Power Consumption 3,5W, 5,5W (IR on), 8,5W (IR and heater on)

Operating Temperature -40°C ~ 55°C

Cold Start Minimum Temperature -25°C

Degree of Protection IP 66

NVIP-1DN5001H/IRH-1P User’s manual ver.1.0

(short form)

7

FOREWORD INFORMATION

1.3. Camera dimensions

NVIP-1DN5001H/IRH-1P User’s manual ver.1.0

(short form)

8

1.4. Package contents

After you open the package make sure that the following elements are inside:

IP camera

230 VAC / 12 VDC power supply

Accessories bag

Short version of user’s manual

CD containing manual and software

If any of this elements has been damaged during transport, pack all the elements back into the original

box and contact your supplier for further assistance.

CAUTION!

If the device was brought from a location with lower temperature, please wait until it reaches the

temperature of location it is currently in. Turning the device on immediately after bringing it

from a location with lower ambient temperature is forbidden, as the condensing water vapour

may cause short-circuits and damage the device as a result.

Before starting the device familiarize yourself with the description and the role of particular

inputs, outputs and adjusting elements that the device is equipped with.

1.4. Package contents

After you open the package make sure that the following elements are inside:

IP camera

Accessories bag

Mounting Template

Short version of user’s manual

CD containing manual and software

If any of this elements has been damaged during transport, pack all the elements back into the original

box and contact your supplier for further assistance.

CAUTION!

If the device was brought from a location with lower temperature, please wait until it reaches the

temperature of location it is currently in. Turning the device on immediately after bringing it

from a location with lower ambient temperature is forbidden, as the condensing water vapour

may cause short-circuits and damage the device as a result.

Before starting the device familiarize yourself with the description and the role of particular

inputs, outputs and adjusting elements that the device is equipped with.

FOREWORD INFORMATION

NVIP-1DN5001H/IRH-1P User’s manual ver.1.0

(short form)

9

2. START-UP AND INITIAL IP CAMERA CONFIGURATION

2.1. Camera overview

2.2. Cabel connectors

START-UP AND INITIAL CAMERA CONFIGURATION

No.

Description

1

RJ-45 network connector

2

12V DC Power In 2.1 mm x 5.5 mm

1

2

NVIP-1DN5001H/IRH-1P User’s manual ver.1.0

(short form)

10

2.3. NVIP-1DN5001H/IRH-1P mounting

1. Unpack the camera from box, checking for any missing parts.

2. Loosen the adjustment nut on bracket, turn anti-clockwise

3. Plan the camera installation site remembering to include the position of the camera relative to the

plane of the installation.

To mount the camera on the ceiling bend the attachment base relative to the camera at an angle of 90

degrees and tighten the locking ring clockwise rotation.

Attach the camera base or template to the mounting place and mark the fixing pins and possible cable

exit holes.

START-UP AND INITIAL CAMERA CONFIGURATION

NVIP-1DN5001H/IRH-1P User’s manual ver.1.0

(short form)

11

When installing on the wall put your camera in the desired location, and set the camera position then

tighten the locking ring clockwise rotation.

Mark the fixing points and transition to cable using camera base or template in desired position.

4. Mount the camera in a designated area using the included mounting studs. Connect power network

as required either before or after bracket is attached to surface, if you are making hole for cable in

surface for pass-thought then be sure this task is completed before the bracket is attached to the

surface.

Caution : Make sure to follow the correct polarity if connecting the camera to DC power. The

central pin is positive polarity .

START-UP AND INITIAL CAMERA CONFIGURATION

NVIP-1DN5001H/IRH-1P User’s manual ver.1.0

(short form)

12

2.4. Starting the IP camera

To run NOVUS IP camera you have to connect ethernet cable between camera and network switch

with PoE support (IEEE 802.3af).

You can also connect it directly via power supply adapter with parameters compatible with camera

power supply specification.

Initialization process is then started which can take about 2 minutes. You can then proceed to connect

to the camera via web browser.

The recommended way to start an IP camera and perform its configuration is a connection directly

to the network switch which is not connected to other devices. To obtain further information about

network configuration parameters (IP address, gateway, network mask, etc.) please contact your

network administrator.

Connection utilising network switch with PoE support

Connection utilising external power supply and network switch

START-UP AND INITIAL CAMERA CONFIGURATION

Power supply and

network transmission

Computer

IP Camera

Network Switch

PoE

Network transmission

IP Camera

Network transmission

Network Switch

Computer

Network transmission

NVIP-1DN5001H/IRH-1P User’s manual ver.1.0

(short form)

13

Connection utilising external power supply directly to the computer

Information:

Power supply adapter is not included. Please use power adapter with parameters specified in user‘s

manual.

Caution:

In order to provide protection against voltage surges/lightning strikes, usage of appropriate surge

protectors is advised. Any damages resulting from surges are not eligible for service repairs.

2.5. Initial configuration via the web browser

The default network settings for NVIP-1DN5xxx IP camera series are :

1. IP address= 192.168.1.200

2. Network mask - 255.255.255.0

3. Gateway - 192.168.1.1

4. User name - root

5. Password - pass

Knowing the camera’s IP address you need to appropriately set PC IP address, so the two devices can

operate in one network subnet ( e.g. for IP 192.168.1.1, appropriate address for the camera ranges from

192.168.1.2 to 192.168.1.254, for example 192.168.1.60). It is not allowed to set the same addresses for

camera and PC computer

You can either set a network configuration (IP address, gateway, net mask, etc.) of NOVUS IP camera

yourself or select DHCP mode (DHCP server is required in this method in target network) by using

web browser or by NMS software. When you use DHCP server check IP address lease and its linking

with camera MAC address to avoid changing or losing IP address during device operation or network/

DHCP server breakdown. You have to remember to use a new camera IP address after changing

network parameters.

After network setting configuration has been done, the camera can be connected to a target network.

START-UP AND INITIAL CAMERA CONFIGURATION

Network transmission - cross over cable

IP Camera

Computer

NVIP-1DN5001H/IRH-1P User’s manual ver.1.0

(short form)

14

3. NETWORK CONNECTION UTILIZING WEB BROSWER

3.1. Recommended PC specification for web browser connections

Requirements below apply to connection with an IP camera, assuming smooth image display

in 1280x960 resolution and 25 fps speed.

1. CPU Intel Pentium IV 3 GHz or newer

2. RAM Memory min. 512 MB

3. VGA card (any displaying Direct 3D with min. 128 MB RAM memory)

4. OS Windows XP / VISTA /Windows 7 / Windows 8

5. Direct X version 9.0 or newer

6. Network card 10/100/1000 Mb/s

3.2. Connection with IP camera via the Internet Explorer

You have to enter camera IP address in the Internet Explorer address bar. If IP address is correct user

login window will be displayed:

Default user is root and default password is pass.

In the Language box you can change the display language. The default language is English.

For safety reasons, it is recommended to change default user name and password.

It is possible to connect to the camera using Internet Explorer, Mozilla Firefox, Chrome or Opera

browsers. Running the IP camera in this browsers are very similar.

NETWORK CONNECTION UTILIZING WEB BROWSER

NVIP-1DN5001H/IRH-1P User’s manual ver.1.0

(short form)

15

If your computer has Flash Player ins

t

a

ll

ed,

the main screen

for the

camera web interface

opens.

From here you can view and configure the

ca

m

e

ra

.

Caution:

If your computer

does

not

have

Flash Player ins

t

a

ll

ed,

you will be prompted

t

o

select if

y

o

u would like

t

o

use

Activ

eX

or Flash

Play

er

t

o

connect to the

ca

m

e

ra:

Click Click

here to shift playing life video with short delay widget! to

play

live

video

with

ActiveX

control

to

reduce

latency

(recommended): Uses

an

ActiveX

plug-in to connect to the camera. To

install the plug-in, click on the

video

area,

and

select Install

this

Add-on for all

users on this

computer,

and follow the

prompts.

Caution: Please open the

Security settings

of IE browser, and enable the

Download unsigned

ActiveX controls.

Click

Please

download

the latest

version

of

Flash

Player to

play

live video:

Opens

a link to

download Flash Player from

Adobe’s

website.

After

completing the installation, restart your

browser and reconnect to the camera.

Caution: When working in Windows Vista/7/8 the ActiveX applet may be blocked by Windows

Defender or User account control. In such case you should allow to run this applet, or simply

disable these functions.

NETWORK CONNECTION UTILIZING WEB BROWSER

NVIP-1DN5001H/IRH-1P User’s manual ver.1.0

(short form)

16

NETWORK CONNECTION UTILIZING WEB BROWSER

Caution: If you are running Windows Vista/7/8 with Internet Explorer 11, the ActiveX applet can be

blocked through browser security settings. In this situation, you should: add the IP address of the

camera to the view of compatibility (Tools -> Compatibility View Settings, click Add).

Then, in the security settings options, add the camera address to trusted sites and lower the security

level to a minimum.

NVIP-1DN5001H/IRH-1P User’s manual ver.1.0

(short form)

17

NETWORK CONNECTION UTILIZING WEB BROWSER

After making the changes, restart the browser, re-connect to the camera and log on.

NVIP-1DN5001H/IRH-1P User’s manual ver.1.0

(short form)

18

4. WWW INTERFACE - WORKING WITH IP CAMERA

4.1. Displaying live

1. Camera settings

Live Video - Live video preview

Playback - Local recordings playback

Device Info - Device information

Stream Configuration - Video and audio settings for each stream

Device Configuration - Device configuration (e.g. Local Network, Date&Time)

External Device - External device configuration (function unavailable)

Alarm Configuration - Alarm Configuration (Motion alarm, Alarm I/O)

Local Record - Local Record Configuration

Privacy Masking - Configuration up to 5 privacy masks

Network Service - Network services configuration (e.g. DDNS)

Service Center - Service center configuration (e.g. SMTP)

Privilege Manager - users and groups management

Protocol - Protocols settings (e.g. ONVIF)

Device Log - Device Log contains: Operation Log, Alarm Log and Collect Log

Maintenance - Device Restart and restoring Default Settings

WWW INTERFACE - WORKING WITH IP CAMERA

3.

4.

1.

2.

NVIP-1DN5001H/IRH-1P User’s manual ver.1.0

(short form)

19

2. Video Parameter

Stream - Stream configuration (ID: 1~3)

Bite Rate Type - Information about selected bit rate type (VBR or CBR)

Bit Rate (kbps) - Information about bit rate configuration (500 ~ 12000 kbps)

I Frame Interval - Information about I frame interval configuration (available values 1 ~ 60)

Quality - Information about quality configuration (available values 1 ~ 9)

3. Camera Control

Function unavailable.

4. Menu bar

Change Password - Change users password

Sign Out - Log out from camera

WWW INTERFACE - WORKING WITH IP CAMERA

NVIP-1DN5001H/IRH-1P User’s manual ver.1.0

(short form)

20

5. ELECTRIC CONNECTORS AND ACCESORIES

5.1. Connecting power supply to the camera.

The camera can be supplied by using RJ45 network socket or by power connector. To run NOVUS IP

camera you can connect ethernet cable between camera and network switch with PoE support (IEEE

802.3af). You can also use a power injector compatible with (IEEE 802.3af) standard. Use power

supplay with parameters compatible with camera specification to power camera via power in jack.

Information:

Power supply adapter is not included. Please use power adapter with parameters specified in user’s

manual.

Caution : Make sure to follow the correct polarity if connecting the camera to DC power. The

central pin is positive polarity .

In order to provide protection against voltage surges/lightning strikes, usage of appropriate surge

protectors is advised. Any damages resulting from surges are not eligible for service repairs.

6. RESTORING FACTORY DEFAULTS

NOVUS IP cameras allow to restore defaults via:

Software (web browser level) resetting the camera settings

Hardware (using reset) restores factory defaults.

6.1. Restoring software factory defaults

Restoring factory software default can restore default settings of the IP camera , optionally network

settings can be saved.

Logon to the camera and choose MAINTENANCE> DEFAULT SETTINGS

Check the Save the IP setting box to preserve IP setting after restore.

Click Restore button. The camera re-starts then, taking about two minutes to complete.

Log on approx. using default user name (root) and password (pass)

ELECTRIC CONNECTORS AND ACCESORIES

Strona jest ładowana ...

Novus NVIP-1DN5001H/IRH-1P Instrukcja obsługi

Novus NVIP-1DN5001H/IRH-1P Instrukcja obsługi

w innych językach

Powiązane dokumenty

Inne dokumenty