Novus NVIP-4DN5002V/IRH-1P Instrukcja obsługi

U s e r ’s m a n u a l

(short form)

NVIP-4DN5002V/IRH-1P

NVIP-4DN5002V/IRH-1P User’s manual ver.1.0

(short form)

2

IMPORTANT SAFEGUARDS AND WARNINGS

EMC (2014/30/EU) and LVD (2014/35/EU ) Directives

CE Marking

Our products are manufactured to comply with requirements of the following directives and national regulations

implementing the directives:

 Electromagnetic compatibility EMC 2014/30/EU.

 Low voltage LVD 2014/35/EU with further amendment. The Directive applies to electrical

equipment designed for use with a voltage rating of between 50VAC and 1000VAC as well as

75VDC and 1500VDC.

WEEE Directive 2012/19/UE

Information on Disposal for Users of Waste Electrical and Electronic Equipment

This appliance is marked according to the European Directive on Waste Electrical and Electronic

Equipment (2012/19/UE) and further amendments. By ensuring this product is disposed of correctly,

you will help to prevent potential negative consequences for the environment and human health, which

could otherwise be caused by inappropriate waste handling of this product.

The symbol on the product, or the documents accompanying the product, indicates that this appliance may not be

treated as household waste. It shall be handed over to the applicable collection point for used up electrical and

electronic equipment for recycling purpose. For more information about recycling of this product, please contact

your local authorities, your household waste disposal service or the shop where you purchased the product.

RoHS Directive 2011/65/UE

Out of concern for human health protection and friendly environment, we assure that our products

falling under RoHS Directive regulations, regarding the restriction of the use of hazardous substances

in electrical and electronic equipment, have been designed and manufactured in compliance with the

above mentioned regulations. Simultaneously, we claim that our products have been tested and do not

contain hazardous substances whose exceeding limits could have negative impact on human health or

natural environment

Information

The device, as a part of professional CCTV system used for surveillance and control, is not designed for self

installation in households by individuals without technical knowledge.

Excluding of responsibility in case of damaging data on a disk or other devices:

The manufacturer does not bear any responsibility in case of damaging or losing data on a disk or other devices

during device operation.

WARNING!

PRIOR TO UNDERTAKING ANY ACTION THAT IS NOT DESCRIBED FOR THE GIVEN PRODUCT IN

USER’S MANUAL AND OTHER DOCUMENTS DELIVERED WITH THE PRODUCT, OR IF IT DOES

NOT ARISE FROM THE USUAL APPLICATION OF THE PRODUCT, MANUFACTURER MUST BE

CONTACTED UNDER THE RIGOR OF EXCLUDING THE MANUFACTURER’S RESPONSIBILITY FOR

THE RESULTS OF SUCH AN ACTION.

NVIP-4DN5002V/IRH-1P User’s manual ver.1.0

(short form)

3

IMPORTANT SAFEGUARDS AND WARNINGS

WARNING!

THE KNOWLEDGE OF THIS MANUAL IS AN INDISPENSIBLE CONDITION OF A PROPER

DEVICE OPERATION. YOU ARE KINDLY REQEUSTED TO FAMILIARIZE YOURSELF WITH

THE MANUAL PRIOR TO INSTALLATION AND FURTHER DEVICE OPERATION.

WARNING!

USER IS NOT ALLOWED TO DISASSEMBLE THE CASING AS THERE ARE NO USER

-SERVICEABLE PARTS INSIDE THIS UNIT. ONLY AUTHORIZED SERVICE PERSONNEL

MAY OPEN THE UNIT

INSTALLATION AND SERVICING SHOULD ONLY BE DONE BY QUALIFIED SERVICE

PERSONNEL AND SHOULD CONFORM TO ALL LOCAL REGULATIONS

1. Prior to undertaking any action please consult the following manual and read all the safety and operating

instructions before starting the device.

2. Please keep this manual for the lifespan of the device in case referring to the contents of this manual is

necessary;

3. All the safety precautions referred to in this manual should be strictly followed, as they have a direct

influence on user’s safety and durability and reliability of the device;

4. All actions conducted by the servicemen and users must be accomplished in accordance with the user’s

manual;

5. The device should be disconnected from power sources during maintenance procedures;

6. Usage of additional devices and components neither provided nor recommended by the producer is

forbidden;

7. You are not allowed to use the camera in high humidity environment (i.e. close to swimming pools, bath tubs,

damp basements);

8. Mounting the device in places where proper ventilation cannot be provided (e. g. closed lockers etc.) is not

recommended since it may lead to heat build-up and damaging the device itself as a consequence;

9. Mounting the camera on unstable surface or using not recommended mounts is forbidden. Improperly

mounted camera may cause a fatal accident or may be seriously damaged itself. The camera must be mounted

by qualified personnel with proper authorization, in accordance with this user’s manual.

10. Device should be supplied only from a power sources whose parameters are in accordance with those

specified by the producer in the camera technical datasheet. Therefore, it is forbidden to supply the camera

from a power sources with unknown parameters, unstable or not meeting producer’s requirements;

Due to the product being constantly enhanced and optimized, certain parameters and functions described in the

manual in question may change without further notice. We strongly suggest visiting the www.novuscctv.com

website in order to access the newest manual

Data included in the following user’s manual is up to date at the time of printing. AAT Holding S.A. holds

exclusive rights to modify this manual. The producer reserves the rights for device specification modification

and change in the design without prior notice.

NVIP-4DN5002V/IRH-1P User’s manual ver.1.0

(short form)

4

TABLE OF CONTENTS ..................................................................................................... 4

1. FOREWORD INFORMATION ................................................................................... ..5

1.1. General Characteristics ........................................................................................ 5

1.2. NVIP-4DN5002V/IRH-1P tech specification ................................................. ...6

1.3. Camera dimension ........................................................................................... ...7

1.4. Package contents ............................................................................................... ...8

2. START-UP AND INITIAL IP CAMERA CONFIGURATION ................................. 9

2.1. Description of connectors and control tools ........................................................ 9

2.2. Cable connectors .................................................................................................. 9

2.3. NVIP-4DN5002V/IRH-1P mounting ................................................................ 10

2.4. Starting the IP camera ........................................................................................ 13

2.5. Initial configuration via the Web browser ......................................................... 14

3. NETWORK CONNECTION UTILIZING WEB BROSWER ................................ 15

3.1. Recommended PC specification for web browser ............................................. 15

3.2. Connection with IP camera via the Internet Explorer ........................................ 15

4. WWW INTERFACE - WORKING WITH IP CAMERA ......................................... 18

4.1. Displaying live pictures. ..................................................................................... 18

5. ELECTRIC CONNECTORS AND ACCESORIES ................................................. 19

5.1. Connecting power supply to the camera. .......................................................... 19

5.2. SD card installation ........................................................................................... 19

5.3. Connecting alarm inputs and output .................................................................. 20

6. RESTORING FACTORY DEFAULTS ..................................................................... 20

6.1. Restoring software factory defaults .................................................................... 20

6.2. Restoring hardware factory defaults in IP cameras ............................................ 20

TABLE OF CONTENTS

NVIP-4DN5002V/IRH-1P User’s manual ver.1.0

(short form)

5

1. FOREWORD INFORMATION

1.1. General Characteristics

 Imager resolution: 4 megapixels

 Mechanical IR cut filter

 IR operation capability

 Min. Illumination from 0,025 lx/F=1.2 (DSS) , 0 lx (IR on)

 Digital Slow Shutter (DSS)

 Digital Noise Reduction (DNR)

 Wide Dynamic Range (WDR)

 Lens f=2.8m/F=1.2

 Built-in IR LED - 1 pcs., up to 10 m

 Privacy zones: 8

 Compression: H.264, H.265, M-JPEG

 Max video processing resolution : 2592 x 1520

 Dual stream mode: compression, resolution, speed and quality defined individually for two video

streams

 RTP/RTSP protocol support for video transmission

 Hardware motion detection

 Built-in webserver: camera configuration through the website

 MicroSD card support

 Wide range of responses to alarm events: e-mail with attachment, saving file on microSD card,

 Network protocol support : ONVIF Profile S (2.6) ,HTTP, TCP/IP, IPv4, UDP, HTTPS,

Multicast, FTP, DHCP, DNS, RTSP, RTP, UPnP, PPPoE, SMTP, RTCP

 Software: NMS (NOVUS MANAGEMENT SYSTEM) for video recording, live monitoring,

playback and remote IP devices administration

 Power supply: 12VDC, PoE (Power over Ethernet)

FOREWORD INFORMATION

NVIP-4DN5002V/IRH-1P User’s manual ver.1.0

(short form)

6

FOREWORD INFORMATION

1.2. Specification

Image

Image Sensor 4 MPX CMOS sensor 1/3”

Number of Effective Pixels 2688 (H) x 1520 (V)

Min. Illumination

0.05 lx/F1.2 - color mode,

0.025 lx/F1.2 - color mode (DSS),

0 lx (IR on) - B/W mode

Electronic Shutter auto/manual: 1 s ~ 1/20000 s

Digital Slow Shutter (DSS) up to 1 s

Wide Dynamic Range (WDR) yes

Digital Image Stabilization (DIS) yes

Digital Noise Reduction (DNR) 2D, 3D

Defog Function (F-DNR) yes

Lens

Lens Type standard, f=2.8 mm/F1.2

Day/Night

Switching Type mechanical IR cut filter

Switching Mode auto, manual, time

Switching Level Adjustment yes

Switching Delay 0 ~ 180 s

Switching Schedule yes

Visible Light Sensor yes

Network

Stream Resolution

2592 x 1520, 2560 x 1440 (QHD), 2304 x 1296, 1920 x 1080 (Full HD), 1280 x 720 (HD), 704 x

576, 640 x 480 (VGA), 640 x 360, 352 x 288 (CIF), 320 x 240 (QVGA)

Frame Rate

20 fps for 2592 x 1520,

25 fps for 2304 x 1296 and lower

Multistreaming Mode 2 streams

Video/Audio Compression H.264, H.265, MJPEG/G.711, RAW_PCM

Number of Simultaneous

Connections

max. 8

Bandwidth 30 Mb/s in total

Network Protocols Support

HTTP, TCP/IP, IPv4, UDP, HTTPS, Multicast, FTP, DHCP, DNS, RTSP, RTP, UPnP, PPPoE,

SMTP, RTCP

ONVIF Protocol Support Profile S (ONVIF 2.6)

Camera Configuration

from Internet Explorer browser

languages: Polish, English, Russian, and others

Compatible Software NMS

Other functions

Privacy Zones 4

Motion Detection yes

Region of interest (ROI) 8

Image Processing 90˚ image rotation, 180˚ image rotation, mirror effect

System Reaction to Alarm Events e-mail with attachment, saving file on FTP server, saving file on SD card

IR LED

LED Number 1

Range 10 m

Angle 90°

Interfaces

Video Output BNC, 1.0 Vp-p, 75 Ohm - maintenance only

Audio Input/Output 1 x RCA/1 x RCA

Network Interface 1 x Ethernet - RJ-45 interface, 10/100 Mbit/s

Memory Card Slot microSD - capacity up to 128GB

Installation parameters

Dimensions (mm) 100 (Ф) x 53 (H)

Weight 0.4 kg

Degree of Protection IP 65 (details in the user’s manual)

Enclosure vandal proof aluminium, white

Power Supply PoE, 12 VDC

Power Consumption

3 W,

5 W (IR on),

5.5 W (heater on),

7.5 W (IR and heater on)

Operating Temperature -30°C ~ 60°C

Built-in Heater/Fan yes/no

NVIP-4DN5002V/IRH-1P User’s manual ver.1.0

(short form)

7

FOREWORD INFORMATION

1.3. Camera dimensions

100 mm

30.3 mm

53 mm

100 mm

49 mm

NVIP-4DN5002V/IRH-1P User’s manual ver.1.0

(short form)

8

1.4. Package contents

After you open the package make sure that the following elements are inside:

 IP camera

 Accessories bag

 BNC Test Cable

 Mounting Template

 Short version of user’s manual

If any of this elements has been damaged during transport, pack all the elements back into the original

box and contact your supplier for further assistance.

Caution:

If the device was brought from a location with lower temperature, please wait until it reaches the

temperature of location it is currently in. Turning the device on immediately after bringing it

from a location with lower ambient temperature is forbidden, as the condensing water vapour

may cause short-circuits and damage the device as a result.

Before starting the device familiarize yourself with the description and the role of particular

inputs, outputs and adjusting elements that the device is equipped with.

Caution:

In order to provide protection against voltage surges/lightning strikes, usage of appropriate surge

protectors is advised. Any damages resulting from surges are not eligible for service repairs.

Caution:

It is forbidden to use – as the camera power source – PoE equipment (adapters, etc.) not compatible

with IEEE 802.3af standard (items called “passive PoE power supply”). Damages that results from

the usage of improper power supply source are not covered by the warranty.

Caution:

Camera connectors / sockets are not hermetic. The user should ensure their hermeticity on his

own.

Caution:

Please note that the wall or ceiling must have enough strength to support the IP Camera.

Caution:

In order to obtain declared degree of protection please seal the camera base to prevent water

getting inside. Furthermore, when installing the camera on rough/uneven surfaces, please

additionally seal the junction with appropriate sealing mass. Please pay special attention to any

mounting holes and if they are a loop-through ones, seal them too.

Caution:

The declared degree of protection of the camera relates to its housing and does not take into account

the possibility of moisture infiltration into the interior of the camera by connecting cables.

Connection cables protection through i.e. sealing up is the responsibility of the camera installer. The

manufacturer is not liable for any damages to the camera caused as a result of failing in performing

that activity by installer, which also means that camera damaged in that way is not subject to

warranty repairs.

FOREWORD INFORMATION

NVIP-4DN5002V/IRH-1P User’s manual ver.1.0

(short form)

9

2. START-UP AND INITIAL IP CAMERA CONFIGURATION

2.1. Camera interior overview

2.2. Cabel connectors

START-UP AND INITIAL CAMERA CONFIGURATION

No. Color of connectors Description

1 - RJ-45 female network connector

2 - 12V DC Power In

3 White RCA Audio input

4 Red RCA Audio output

NVIP-4DN5002V/IRH-1P User’s manual ver.1.0

(short form)

10

2.3. NVIP-4DN5002V/IRH-1P mounting

1.Use the included allen key to remove the camera cover screws (2x). Lift the cover away from the

camera

2. Use the included mounting template or the camera to mark holes for the mounting screws and cable.

3. Mount the camera to the surface using the included mounting screws (2x)

START-UP AND INITIAL CAMERA CONFIGURATION

Mounting Screw Hole

Termination cables

Mounting Screws

NVIP-4DN5002V/IRH-1P User’s manual ver.1.0

(short form)

11

4. To adjust the viewing angle power up the camera. Connect to the camera using a web browser or

you can insert the included BNC test cable into video test cable terminals and connect to a test monitor.

Caution:

Before connecting the camera's power supply, please check the chapter 2.4 and 5.1

Loosen the screws on the sides of the and adjust the ball camera. Do not remove the screws holding the

ball camera. Tighten the screws when finished.

Note: Make sure the camera is pointed in the same direction as the IR LED to ensure a good night

image.

START-UP AND INITIAL CAMERA CONFIGURATION

Video test cable

Loosen screws to adjust the

angle of the camera ball

IR LED

NVIP-4DN5002V/IRH-1P User’s manual ver.1.0

(short form)

12

5. (Optional) Insert a microSD card (not in set included ) into the camera. To enable recording, you

must format the microSD card and configure microSD recording. Before installing microSD card check

details in chapter 5.3.

6. Ensure the rubber gasket inside the camera is properly in place, then replace the camera cover and

the camera cover screws (2x).

START-UP AND INITIAL CAMERA CONFIGURATION

MicroSD card

NVIP-4DN5002V/IRH-1P User’s manual ver.1.0

(short form)

13

2.4. Starting the IP camera

To run NOVUS IP camera you have to connect ethernet cable between camera and network switch

with PoE support (IEEE 802.3af).

You can also connect it directly via power supply adapter with parameters compatible with camera

power supply specification. Check details in chapter 5.1

After connecting power status red LED should light on. Initialization process is then started which can

take about 2 minutes. You can then proceed to connect to the camera via web browser.

If the connection is successfully established green network status LED blinks with a frequency

proportional to the quantity of data sent.

The recommended way to start an IP camera and perform its configuration is a connection directly

to the network switch which is not connected to other devices. To obtain further information about

network configuration parameters (IP address, gateway, network mask, etc.) please contact your

network administrator.

 Connection utilising network switch with PoE support

 Connection utilising external power supply and network switch

START-UP AND INITIAL CAMERA CONFIGURATION

Computer IP Camera

Power supply and

network transmission

Network Switch

PoE

Network transmission

IP Camera

Network transmission

Computer

Network Switch

Network transmission

NVIP-4DN5002V/IRH-1P User’s manual ver.1.0

(short form)

14

 Connection utilising external power supply directly to the computer

Note :

Power supply adapter is not included. Please use power adapter with parameters specified in user‘s

manual.

Caution:

In order to provide protection against voltage surges/lightning strikes, usage of appropriate surge

protectors is advised. Any damages resulting from surges are not eligible for service repairs.

2.5. Initial configuration via the web browser

The default network settings for NVIP-4DN5002V/IRH-1P camera are :

1. IP address= 192.168.1.200

2. Network mask - 255.255.255.0

3. Gateway - 192.168.1.1

4. User name - root

5. Password - pass

Knowing the camera’s IP address you need to appropriately set PC IP address, so the two devices can

operate in one network subnet ( e.g. for IP 192.168.1.1, appropriate address for the camera ranges from

192.168.1.2 to 192.168.1.254, for example 192.168.1.60). It is not allowed to set the same addresses for

camera and PC computer

You can either set a network configuration (IP address, gateway, net mask, etc.) of NOVUS IP camera

yourself or select DHCP mode (DHCP server is required in this method in target network) by using

web browser or by NMS software. When you use DHCP server check IP address lease and its linking

with camera MAC address to avoid changing or losing IP address during device operation or network/

DHCP server breakdown. You have to remember to use a new camera IP address after changing

network parameters.

After network setting configuration has been done, the camera can be connected to a target network.

START-UP AND INITIAL CAMERA CONFIGURATION

IP Camera

Network transmission - cross over cable

Computer

NVIP-4DN5002V/IRH-1P User’s manual ver.1.0

(short form)

15

3. NETWORK CONNECTION UTILIZING WEB BROSWER

3.1. Recommended PC specification for web browser connections

Requirements below apply to connection with an IP camera, assuming image display in 2592x1520

resolution and 20 fps speed.

1. CPU Intel Core i3 3 GHz or newer

2. RAM Memory min. 4 GB

3. VGA card NVidia GeForce with 512 MB of RAM memory, or equivalent

4. OS Windows 7 / 8 / 8.1 / 10

5. Network card 100/1000 Mb/s

3.2. Connection with IP camera via the Internet Explorer

You have to enter camera IP address in the Internet Explorer address bar. If IP address is correct user

login window will be displayed:

Default user is root and default password is pass.

In selection list you can change the display language. The default language is English.

For safety reasons, it is recommended to change default user name and password.

NETWORK CONNECTION UTILIZING WEB BROWSER

NVIP-4DN5002V/IRH-1P User’s manual ver.1.0

(short form)

16

If you’re first time running the camera, you will see screen as below.

To correctly camera working, you need a plugin, you have to download and install it as belowe.

 Click Download and setup and follow the prompts.

NETWORK CONNECTION UTILIZING WEB BROWSER

Download and setup

Please reopen the browser after installing

NVIP-4DN5002V/IRH-1P User’s manual ver.1.0

(short form)

17

NETWORK CONNECTION UTILIZING WEB BROWSER

 Click Install button

 After installation, click Finished button

Caution: In Windows Vista/7/8/10 the ActiveX applet may be blocked by Windows Defender or

User account control. In such case you should allow to run this applet, or simply disable these

functions.

Caution: If the installation fails, changing security settings for the IE browser is required. In order to do

that, please choose: Tools > Internet options > Security tab > Custom level and:

 Under Download unsigned ActiveX controls - select either Enable or Prompt

 Under Initialize and script ActiveX controls not marked as safe - select Enable or Prompt

NVIP-4DN5002V/IRH-1P User’s manual ver.1.0

(short form)

18

4. WWW INTERFACE - WORKING WITH IP CAMERA

4.1. Displaying live pictures

1. Camera menu:

 Live Video - opens the camera live video

 Playback - opens the camera playback

 Configuration - opens the camera configuration menu

2. Change Password and Sign out buttons - are used to change the password and log off the current

user.

3. Live video preview

4. Stream information

5. Live video menu

 Selection of strem preview

 Selection of camera - option not available

 Selection of additional camera configuration - option not available

 Video button- turn-on/off camera preview output

 Live / Smooth Button- turn-on smooth preview option

 Audio button- turn-on/off audio output

 Interphone button- turn-on/off audio input and output

 Sensor button- turn-on sensor configuration menu

 Snapshot button- make a preview snapshot

 Selection of additional camera configuration - option not available

WWW INTERFACE - WORKING WITH IP CAMERA

1.

3.

4.

5.

2.

NVIP-4DN5002V/IRH-1P User’s manual ver.1.0

(short form)

19

ELECTRIC CONNECTORS AND ACCESORIES

5. ELECTRIC CONNECTORS AND ACCESORIES

5.1. Connecting power supply to the camera.

The camera can be supplied by using RJ45 network socket or by power connector. To run NOVUS IP

camera you can connect ethernet cable between camera and network switch with PoE support (IEEE

802.3af). You can also use a power injector with (IEEE 802.3af) PoE standard. Use power supplay with

parameters compatible with camera specification to power camera via power in jack.

Information:

Power supply adapter is not included. Please use power adapter with parameters specified in user’s

manual.

SCHEMA OF 12VDC POWER SUPPLY CONNECTOR

Caution : Make sure to follow the correct polarity if connecting the camera to DC power.

Polarity is marked on the power connector.

Caution: In order to provide protection against voltage surges/lightning strikes, usage of

appropriate surge protectors is advised. Any damages resulting from surges are not eligible for

service repairs.

Caution: It is forbidden to use as the camera power source PoE equipment (adapters, etc.) not

compatible with IEEE 802.3af standard (items called “passive PoE power supply”). Damages that

results from the usage of improper power supply source are not covered by the warranty.

5.2. SD card installation

Camera supports microSD cards with their capacity up to 128GB. In order to install the card properly,

please follow the instructions below:

 Turn the camera off

 Mount microSD card in the socket , according to the picture:

MicroSD card

NVIP-4DN5002V/IRH-1P User’s manual ver.1.0

(short form)

20

 Turn the camera on

 Format the card using a IP camera.

Click

Local

Record ->Record Directory. Click

Modify.

In menu click Format button.

A window will appear click OK to start formating

.

Wait

for

the formatting to complete and then

click OK.

5.3. Connecting audio inputs/outputs.

6. RESTORING FACTORY DEFAULTS

NOVUS IP cameras allow to restore defaults via:

 Software (web browser level) resetting the camera settings

 Hardware (using reset) restores factory defaults.

6.1. Restoring software factory defaults

Restoring factory software default can restore default settings of the IP camera ,optionally network

settings can be saved.

Logon to the camera and choose MAINTENANCE. Check the Save the IP setting box to preserve IP

setting after restore. Click Restore button. The camera re-starts then, taking about two minutes to

complete. Log on approx. using default user name (root) and password (pass)

6.2. Restoring hardware factory defaults in IP cameras

In order to restore factory defaults for the camera please follow the instructions:

 Remove the camera cover screws (2x) and remove the camera cover

 Press and hold the white reset button for 5 seconds then release the button to reset the camera to

factory defaults

 Re-attach the camera cover and replace the camera cover screws (2x)

 Log on after approx. 2 minutes using default IP address (http://192.168.1.200) and default user

name (root) and password (pass)

RESET button

ELECTRIC CONNECTORS AND ACCESORIES

Color Description

White RCA Audio input— Connect to a self-powered microphone for

listen-in audio.

Red

RCA Audio output— Connect to anamplifier or self-powered spea-

ker for intercom/2-way audio

Strona jest ładowana ...

Novus NVIP-4DN5002V/IRH-1P Instrukcja obsługi

Novus NVIP-4DN5002V/IRH-1P Instrukcja obsługi

w innych językach

Powiązane dokumenty

Inne dokumenty