Novus NVIP-4DN5002H/IRH-1P Instrukcja obsługi

U s e r ’s m a n u a l

(s h ort )

NVIP-4DN5002H/IRH-1P

NVIP-4DN5002H/IRH-1P User’s manual (short form) ver.1.1

2

IMPORTANT SAFEGUARDS AND WARNINGS

EMC (2004/108/EC) and LVD (2006/95/EC ) Directives

CE Marking

Our products are manufactured to comply with requirements of the following directives and national regulations

implementing the directives:

 Electromagnetic compatibility EMC 2004/108/EC.

 Low voltage LVD 2006/95/EC with further amendment. The Directive applies to electrical

equipment designed for use with a voltage rating of between 50VAC and 1000VAC as well as

75VDC and 1500VDC.

WEEE Directive 2012/19/EU

Information on Disposal for Users of Waste Electrical and Electronic Equipment

This appliance is marked according to the European 1000VAC Directive on Waste Electrical and Electronic

Equipment (2012/19/EU) and further amendments. By ensuring this product is disposed of correctly, you will

help to prevent potential negative consequences for the environment and human health, which could otherwise

be caused by inappropriate waste handling of this product.

The symbol on the product, or the documents accompanying the product, indicates that this appliance may not be

treated as household waste. It shall be handed over to the applicable collection point for used up electrical and

electronic equipment for recycling purpose. For more information about recycling of this product, please contact

your local authorities, your household waste disposal service or the shop where you purchased the product.

RoHS Directive 2011/11/EU

Out of concern for human health protection and friendly environment, we assure that our products

falling under RoHS Directive regulations, regarding the restriction of the use of hazardous substances

in electrical and electronic equipment, have been designed and manufactured in compliance with the

above mentioned regulations. Simultaneously, we claim that our products have been tested and do not

contain hazardous substances whose exceeding limits could have negative impact on human health or

natural environment

Information

The device, as a part of professional CCTV system used for surveillance and control, is not designed for self

installation in households by individuals without technical knowledge.

Excluding of responsibility in case of damaging data on a disk or other devices:

The manufacturer does not bear any responsibility in case of damaging or losing data on a disk or other devices

during device operation.

WARNING!

PRIOR TO UNDERTAKING ANY ACTION THAT IS NOT DESCRIBED FOR THE GIVEN

PRODUCT IN USER’S MANUAL AND OTHER DOCUMENTS DELIVERED WITH THE

PRODUCT, OR IF IT DOES NOT ARISE FROM THE USUAL APPLICATION OF THE

PRODUCT, MANUFACTURER MUST BE CONTACTED UNDER THE RIGOR OF EXCLUDING THE

MANUFACTURER’S RESPONSIBILITY FOR THE RESULTS OF SUCH AN ACTION.

NVIP-4DN5002H/IRH-1P User’s manual (short form) ver.1.1

3

IMPORTANT SAFEGUARDS AND WARNINGS

WARNING!

THE KNOWLEDGE OF THIS MANUAL IS AN INDISPENSIBLE CONDITION OF A PROPER

DEVICE OPERATION. YOU ARE KINDLY REQEUSTED TO FAMILIARIZE YOURSELF WITH

THE MANUAL PRIOR TO INSTALLATION AND FURTHER DEVICE OPERATION.

WARNING!

USER IS NOT ALLOWED TO DISASSEMBLE THE CASING AS THERE ARE NO USER

-SERVICEABLE PARTS INSIDE THIS UNIT. ONLY AUTHORIZED SERVICE PERSONNEL

MAY OPEN THE UNIT

INSTALLATION AND SERVICING SHOULD ONLY BE DONE BY QUALIFIED SERVICE

PERSONNEL AND SHOULD CONFORM TO ALL LOCAL REGULATIONS

1. Prior to undertaking any action please consult the following manual and read all the safety and operating

instructions before starting the device.

2. Please keep this manual for the lifespan of the device in case referring to the contents of this manual

is necessary;

3. All the safety precautions referred to in this manual should be strictly followed, as they have a direct

influence on user’s safety and durability and reliability of the device;

4. All actions conducted by the servicemen and users must be accomplished in accordance with the user’s

manual;

5. The device should be disconnected from power sources during maintenance procedures;

6. Usage of additional devices and components neither provided nor recommended by the producer

is forbidden;

7. Mounting the device in places where proper ventilation cannot be provided (e. g. closed lockers etc.) is not

recommended since it may lead to heat build-up and damaging the device itself as a consequence;

8. Mounting the camera on unstable surface or using not recommended mounts is forbidden. Improperly

mounted camera may cause a fatal accident or may be seriously damaged itself. The camera must be mounted

by qualified personnel with proper authorization, in accordance with this user’s manual.

9. Device should be supplied only from a power sources whose parameters are in accordance with those

specified by the producer in the camera technical datasheet. Therefore, it is forbidden to supply the camera

from a power sources with unknown parameters, unstable or not meeting producer’s requirements;

Due to the product being constantly enhanced and optimized, certain parameters and functions described in the

manual in question may change without further notice. We strongly suggest visiting the www.novuscctv.com

website in order to access the full manual.

Data included in the following user’s manual is up to date at the time of printing. AAT Holding S. A. holds

exclusive rights to modify this manual. The producer reserves the rights for device specification modification

and change in the design without prior notice.

NVIP-4DN5002H/IRH-1P User’s manual (short form) ver.1.1

4

TABLE OF CONTENTS .................................................................................................... 4

1. FOREWORD INFORMATION ................................................................................... ..5

1.1. General Characteristics ........................................................................................ 5

1.2. NVIP-4DN5002H/IRH-1P specification ........................................................... ...6

2. SPECIFICATION .......................................................................................................... ..7

2.1. Camera dimension ........................................................................................... ...7

2.2. Package contents ............................................................................................... ...8

2.3. Layout of important camera items .................................................................... ...9

3. INSTALLATION ........................................................................................................... 10

4. START-UP AND INITIAL CAMERA CONFIGURATION .................................... 12

4.1. Starting the IP camera ....................................................................................... 12

4.2. Initial configuration via the Web browser ......................................................... 13

5. NETWORK CONNECTION UTILIZING WEB BROSWER ................................ 14

5.1. Recommended PC specification for web browser ............................................. 14

5.2. Connection with IP camera via the web browser ............................................... 14

6. WWW INTERFACE - WORKING WITH IP CAMERA ......................................... 16

6.1. Displaying live pictures. ..................................................................................... 16

7. ELECTRIC CONNECTORS AND ACCESORIES ................................................. 18

7.1. Connecting power supply to the camera. .......................................................... 18

7.2. SD card installation ........................................................................................... 18

8. RESTORING FACTORY DEFAULTS .................................................................... 19

8.1. Restoring software factory defaults ................................................................... 19

8.2. Restoring hardware factory defaults in IP cameras ........................................... 19

TABLE OF CONTENTS

NVIP-4DN5002H/IRH-1P User’s manual (short form) ver.1.1

5

1. FOREWORD INFORMATION

1.1. General Characteristics

 Imager resolution: 4.0 megapixels

 Mechanical IR cut filter

 IR operation capability

 Min. Illumination from 0.034lx/F=1.4 (DSS)

 Digital Slow Shutter (DSS)

 Digital Noise Reduction (DNR)

 Lens type: Auto iris DC, f=3 ~ 12mm F=1.4

 Built-in IR illuminator, 10 LEDs

 Privacy zones: 5

 Video compression: H.264, M-JPEG

 Max video processing resolution: 2688x1520

 Double streaming: compression, resolution, speed and quality defined individually for each video

stream

 RTSP protocol support for video transmission

 Pre & post-alarm functions

 Intelligent Analysis: tamper detection, object disappearance detection, line cross detection, zone

entrance detection, line cross detection, loiter, multi loiter, abnormal speed, converse, illegal parking

 Hardware motion detection

 Built-in webserver: camera configuration through the website

 MicroSD/microSDHC card support

 Wide range of responses to alarm events: e-mail with attachment, saving file on FTP server,

saving file on microSD/microSDHC card, saving file on NAS

 Network protocol support : ONVIF (2.2)/Profile S, HTTP, TCP, IPv4/v6, UDP, FTP, DHCP,

NTP, RTSP, PPoE, SMTP

 Software: NMS (NOVUS MANAGEMENT SYSTEM) for video recording, live monitoring,

playback and remote IP devices administration

 Degree protection IP66

 Power supply: 12VDC, PoE (Power over Ethernet)

FOREWORD INFORMATION

NVIP-4DN5002H/IRH-1P User’s manual (short form) ver.1.1

6

1.2. NVIP-4DN5002H/IRH-1P specification

FOREWORD INFORMATION

Image

Image Sensor 4 MPX CMOS sensor 1/3” OV

Number of Effective Pixels 2688 (H) x 1520 (V)

Min. Illumination

0.07 lx/F1.4 - color mode,

0.034 lx/F1.4 - color mode (DSS),

0 lx (IR on) - B/W mode

Electronic Shutter auto/manual: 1/5 s ~ 1/20000 s

Digital Slow Shutter (DSS) up to 1/5 s

Wide Dynamic Range (WDR) yes

Digital Noise Reduction (DNR) 2D, 3D

Lens

Lens Type varifocal auto iris DC, f=3 ~ 12 mm/F1.4

Day/Night

Switching Type mechanical IR cut filter

Switching Mode auto, manual, time

Switching Level Adjustment yes

Switching Delay 0 ~ 180 s

Switching Schedule yes

Visible Light Sensor yes

Network

Stream Resolution

2688 x 1520, 2560 x 1440 (QHD), 2304 x 1296, 1920 x 1080 (Full HD), 1280 x 720 (HD), 704 x 576, 640 x 480

(VGA), 640 x 360, 352 x 288 (CIF), 320 x 240 (QVGA)

Frame Rate

20 fps for 2688 x 1520, 2560 x 1440 (QHD),

25 fps for 2304 x 1296,

30 fps for 1920 x 1080 (Full HD) and lower resolutions

Multistreaming Mode 2 streams

Video/Audio Compression H.264, MJPEG/G.711, RAW_PCM

Number of Simultaneous Connections max. 8

Bandwidth 15 Mb/s in total

Network Protocols Support HTTP, TCP/IP, IPv4/v6, UDP, Multicast, FTP, DHCP, DNS, DDNS, NTP, RTSP, RTP, SMTP

ONVIF Protocol Support Profile S (ONVIF2.2)

Camera Configuration

from Internet Explorer, Firefox, Chrome, Opera browser

languages: Polish, English, Russian, and others

Compatible Software NMS

Other functions

Privacy Zones 5

Motion Detection yes

Video Content Analysis (VCA)

tamper, abandoned object, object disappearance, line cross, zone entrance, double line cross, loiter, multi loiter,

abnormal speed, converse, illegal parking

Image Processing 180˚ image rotation, sharpening, mirror effect, corridor mode

Prealarm/Postalarm up to 5 MB/up to 86400 s

System Reaction to Alarm Events e-mail with attachment, saving file on SD card

IR LED

LED Number 10

Range 20 m

Angle 90°

Interfaces

Video Output BNC, 1.0 Vp-p, 75 Ohm - maintenance only

Audio Input/Output 1 x RCA/1 x RCA

Network Interface 1 x Ethernet - RJ-45 interface, 10/100 Mbit/s

Memory Card Slot microSD - capacity up to 64GB

Installation parameters

Dimensions (mm) with bracket: 83 (W) x 79.8 (H) x 264.5 (L)

Weight 0.83 kg

Degree of Protection IP 66 (details in the user’s manual)

Enclosure aluminium, white, fully cable manged wall mount bracket in-set included

Power Supply PoE, 12 VDC

Power Consumption

5 W,

9 W (IR on),

11 W (IR and heater on)

Operating Temperature -25°C ~ 55°C

Built-in Heater/Fan yes/no

NVIP-4DN5002H/IRH-1P User’s manual (short form) ver.1.1

7

SPECIFICATION

2. SPECIFICATION

2.1. Camera dimensions

NVIP-4DN5002H/IRH-1P User’s manual (short form) ver.1.1

8

1.4. Package contents

After you open the package make sure that the following elements are inside:

 IP camera

 230 VAC / 12 VDC power supply

 Accessories bag

 Short version of user’s manual

 CD containing manual and software

If any of this elements has been damaged during transport, pack all the elements back into the original

box and contact your supplier for further assistance.

CAUTION!

If the device was brought from a location with lower temperature, please wait until it reaches the

temperature of location it is currently in. Turning the device on immediately after bringing it

from a location with lower ambient temperature is forbidden, as the condensing water vapour

may cause short-circuits and damage the device as a result.

Before starting the device familiarize yourself with the description and the role of particular

inputs, outputs and adjusting elements that the device is equipped with.

2.2. Package contents

After you open the package make sure that the following elements are inside:

 IP camera,

 Mounting Screw

Kit



RJ45

Coupler,



BNC

Test Cable,

 Mounting Template,

 Short version of user’s manual.

If any of this elements has been damaged during transport, pack all the elements back into the original

box and contact your supplier for further assistance.

CAUTION!

If the device was brought from a location with lower temperature, please wait until it reaches the

temperature of location it is currently in. Turning the device on immediately after bringing it

from a location with lower ambient temperature is forbidden, as the condensing water vapour

may cause short-circuits and damage the device as a result.

Before starting the device familiarize yourself with the description and the role of particular

inputs, outputs and adjusting elements that the device is equipped with.

SPECIFICATION

NVIP-4DN5002H/IRH-1P User’s manual (short form) ver.1.1

9

1.4. Package contents

After you open the package make sure that the following elements are inside:

 IP camera

 230 VAC / 12 VDC power supply

 Accessories bag

 Short version of user’s manual

 CD containing manual and software

If any of this elements has been damaged during transport, pack all the elements back into the original

box and contact your supplier for further assistance.

CAUTION!

If the device was brought from a location with lower temperature, please wait until it reaches the

temperature of location it is currently in. Turning the device on immediately after bringing it

from a location with lower ambient temperature is forbidden, as the condensing water vapour

may cause short-circuits and damage the device as a result.

Before starting the device familiarize yourself with the description and the role of particular

inputs, outputs and adjusting elements that the device is equipped with.

2.3. Layout of important camera items

1. RJ45 Network Interface: (PoE supported).

Information:

Use the included RJ45 coupler to connect to male end of RJ45 Ethernet cable.

2. Audio Input (RCA): Connect to a self-powered microphone for listen-in audio.

3. Audio Output (RCA): Connect to an amplifier or self-powered speaker for intercom/2-way audio.

4. DC12V: 12V DC power input.

NOTICE: Make sure to follow correct polarity (+/-) marked on the power connector when connecting

to power.

SPECIFICATION

Focus

adjustment

Zoom

adjustment

Reset button

(reverts to factory defaults)

MicroSD card slot

BNC service

analog output

NVIP-4DN5002H/IRH-1P User’s manual (short form) ver.1.1

10

3. INSTALLATION

 Put mounting drawing paper to the wall or ceiling and mark drill holes.

 Drill holes using markings.

 Drill additional hole for video and power cables.

 Put video and power cables through a previously drilled hole in the wall/ceiling.

 Using mounting screws from the package, attach the plate of camera to the ceiling/wall.

 Unscrew the service compartment screws and open the service compartment. Connect the BNC

test cable to video output and monitor.

INSTALLATION

Plate of the

camera

Service

compartment 2

Service

compartment 1

NVIP-4DN5002H/IRH-1P User’s manual (short form) ver.1.1

11

 Unscrew the locking screw and the stopping ring, and then manually point the camera in a

desired direction to obtain a desired scene view.

 Firmly screw the locking screw and the stopping ring.

 Adjust the camera zoom and focus as needed. It is recommended to check focus settings in

infrared illumination and make correction in colour mode to have proper focus in both modes.



Close

the service compartment 1 and firmly screw the service compartment screws.

INSTALLATION

Locking screw

Tighten

Loosen

Horizontal/vertical rotation

Stopping ring

Focus

adjustment

Zoom

adjustment

NVIP-4DN5002H/IRH-1P User’s manual (short form) ver.1.1

12

4, START-UP AND INITIAL CAMERA CONFIGURATION

4.1. Starting the IP camera

To run NOVUS IP camera you have to connect ethernet cable between camera and network switch

with PoE support (IEEE 802.3af).

You can also connect it directly via power supply adapter with parameters compatible with camera

power supply specification.

After connecting power supply initialization process is started, which takes about 2 minutes.

The recommended way to start an IP camera and perform its configuration is connect directly to the

network switch which is not connected to other devices. To obtain further information about network

configuration parameters (IP address, gateway, network mask, etc.) please contact your network

administrator.

 Connection utilising network switch with PoE support

 Connection utilising external power supply and network switch

START-UP AND INITIAL CAMERA CONFIGURATION

Power supply and

Computer

IP Camera

Network Switch PoE

Network transmission

IP Camera

Network transmission

Network Switch PoE

Computer

Network transmission

NVIP-4DN5002H/IRH-1P User’s manual (short form) ver.1.1

13

 Connection utilising external power supply directly to the computer

Information:

Power supply adapter is not included. Please use power adapter with parameters specified in user ‘s

manual.

Caution:

In order to provide protection against voltage surges/lightning strikes, usage of appropriate surge

protectors is advised. Any damages resulting from surges are not eligible for service repairs.

4.2. Initial configuration via the web browser

The default network settings for NVIP-4DN5002H/IRH-1P camera is :

1. IP address= 192.168.1.200

2. Network mask - 255.255.255.0

3. Gateway - 192.168.1.1

4. User name - root

5. Password - pass

Knowing the camera’s IP address you need to appropriately set PC IP address, so the two devices can

operate in one network subnet ( e.g. for IP 192.168.1.1, appropriate address for the camera ranges from

192.168.1.2 to 192.168.1.254, for example 192.168.1.60). It is not allowed to set the same addresses for

camera and PC computer

You can either set a network configuration (IP address, gateway, net mask, etc.) of NOVUS IP camera

yourself or select DHCP mode (DHCP server is required in this method in target network) by using

web browser or by NMS software. When you use DHCP server check IP address lease and its linking

with camera MAC address to avoid changing or losing IP address during device operation or network/

DHCP server breakdown. You have to remember to use a new camera IP address after changing

network parameters.

After network setting configuration has been done, the camera can be connected to a target network.

START-UP AND INITIAL CAMERA CONFIGURATION

IP Camera

Network transmission - cross over cable

Computer

NVIP-4DN5002H/IRH-1P User’s manual (short form) ver.1.1

14

5. NETWORK CONNECTION UTILIZING WEB BROSWER

5.1. Recommended PC specification for web browser connections

Requirements below apply to connection with an IP camera, assuming image display in 2688x1520

resolution and 20 fps speed.

1. CPU Intel Core i3 3 GHz or newer

2. RAM Memory min. 4 GB

3. VGA card NVidia GeForce with 512 MB of RAM memory, or equivalent

4. OS Windows 7 / 8 / 8.1 / 10

5. Network card 100/1000 Mb/s

5.2. Connection with IP camera via the web browser

You have to enter camera IP address in the Internet browser address bar. If IP address is correct user

login window will be displayed:

Default user is root and default password is pass.

In the Language box you can change the display language (English, Polish, Deutsch or Russian). The

default language is English.

For safety reasons, it is recommended to change default user name and password.

It is possible to connect to the camera using Internet Explorer, Mozilla Firefox, Chrome or Opera

browsers. Running the IP camera in this browsers are very similar.

NETWORK CONNECTION UTILIZING WEB BROWSER

NVIP-4DN5002H/IRH-1P User’s manual (short form) ver.1.1

15

If your computer has Flash Player ins

t

a

ll

ed,

the main screen

for the

camera web interface

opens.

From here you can view and configure the

ca

m

e

ra

.

NOTE:

If your computer

does

not

have

Flash Player ins

t

a

ll

ed,

you will be prompted

t

o

select if

y

o

u

would like

t

o

use

Activ

eX

or Flash

Play

er

t

o

connect to the

ca

m

e

ra:



Click Click

here to shift playing life video with short delay widget! to

play

live

video

with

ActiveX

control

to

reduce

latency

(recommended): Uses

an

ActiveX

plug-in to connect to the camera. To

install the plug-in, click on the

video

area,

and

select Install

this

Add-on for all

users on this

computer,

and follow the

prompts.

NOTE:

Please open the Security settings of IE browser, and enable the Download unsigned

ActiveX controls.



Click

Please

download

the latest

version

of

Flash

Player to

play

live video:

Opens

a link to

download Flash Player from

Adobe’s

website.

After

completing the installation, restart your

browser and reconnect to the camera.

NOTE: When working in Windows 7/8/10 the ActiveX applet may be blocked by Windows Defender

or User account control. In such case you should allow to run this applet, or simply disable these

functions.

NETWORK CONNECTION UTILIZING WEB BROWSER

NVIP-4DN5002H/IRH-1P User’s manual (short form) ver.1.1

16

NETWORK CONNECTION UTILIZING WEB BROWSER

NOTE: If you are running Windows Vista/7/8 with Internet Explorer 11, the ActiveX applet can be

blocked through browser security settings. In this situation, you should: add the IP address of the ca-

mera to the view of compatibility (Tools -> Compatibility View Settings, click Add).

Then, in the security settings options, add the camera address to trusted sites and lower the security

level to a minimum.

NVIP-4DN5002H/IRH-1P User’s manual (short form) ver.1.1

17

NETWORK CONNECTION UTILIZING WEB BROWSER

After making the changes, restart the browser, re-connect to the camera and log on.

NVIP-4DN5002H/IRH-1P User’s manual (short form) ver.1.1

18

6. WWW INTERFACE - WORKING WITH IP CAMERA

6.1. Displaying live pictures

1. Camera settings

Live Video - Live video preview

Device Info - Device information

Stream Configuration - Video and audio settings for each stream

Device Configuration - Device configuration (e.g. Local Network, Date&Time)

External Device - External device configuration (function unavailable)

Intelligent analysis - Settings of video analysis

Alarm Configuration - Alarm Configuration (Motion alarm, Alarm I/O)

Local Record - Local Record Configuration

Privacy Masking - Configuration up to 5 privacy masks

Network Service - Network services configuration (e.g. DDNS)

Service Center - Service center configuration (e.g. SMTP)

Privilege Manager - Users and groups management

Protocol - Protocols settings (e.g. ONVIF)

Device Log - Device Log contains: Operation Log, Alarm Log and Collect Log

Maintenance - Device Restart and restoring Default Settings

WWW INTERFACE - WORKING WITH IP CAMERA

3.

4.

1. 2.

5.

NVIP-4DN5002H/IRH-1P User’s manual (short form) ver.1.1

19

2. Video Parameter

Stream - Stream ID (choose one from available streams)

Bite Rate Type - Information about bit rate type

Bit Rate (kbps) - Information about bit rate

I Frame Interval - Information about I frame interval

Quality - Information about quality

USE TIME STAMP - Video buffer (increases delay when enabled, maximum delay is 5s)

NOTICE: USE TIME STAMP function will not be available when using Flash instead of Activex.

3. Camera Control

Function unavailable.

4. Menu bar

Change Password - Change users password

NOTICE: Default password "pass" can be restored only after restoring default settings of the camera)

Sign Out - Log out from camera

5. Video Control

Camera - Default number of the camera is 1.

Video - Turn on/off video

Audio - Turn on/off audio

Interphone - Turn on/off Interphone

NOTICE: Audio and Interphone functions will not be available when using Flash instead of Activex.

WWW INTERFACE - WORKING WITH IP CAMERA

NVIP-4DN5002H/IRH-1P User’s manual (short form) ver.1.1

20

7. ELECTRIC CONNECTORS AND ACCESORIES

7.1. Connecting power supply to the camera.

The camera is supplied by using RJ45 network socket. To run NOVUS IP camera you have to connect

ethernet cable between camera and network switch with PoE support (IEEE 802.3af). You can also use

a power injector compatible with IEEE 802.3af standard.

Information:

Power supply adapter is not included. Please use power adapter with parameters specified in user’s

manual.

Caution:

When connecting the camcorder to the power supply 12VDC should pay attention to proper

polarity markings located on the connector 12VDC power supply.

Caution:

In order to provide protection against voltage surges/lightning strikes, usage of appropriate surge

protectors is advised. Any damages resulting from surges are not eligible for service repairs

7.2. SD card installation

Camera supports microSD and microSDHC cards. In order to install the card properly, please follow

the instructions below:

 Turn the camera off.

 Unscrew the service compartment 2 screws and open the service compartment.

 Mount microSD/microSDHC card in the socket located at the camera’s rear, according to the

picture:



Close

the service compartment 2 and firmly screw the service compartment screws.

 Turn the camera on

 Format the Ext4 file system for IP camera.

Select from the menu Local Recording -> File Locations. In the Name box, select the SD card drive.

Press Change. This opens the window to change the path of recording. Press Format. Window will

appear showing the current status of the card is formatted. When formatting is complete, press the

OK button.

 Check the capacity of the SD card tab Recording Local -> File Locations.

ELECTRIC CONNECTORS AND ACCESORIES

Strona się ładuje...

Novus NVIP-4DN5002H/IRH-1P Instrukcja obsługi

Novus NVIP-4DN5002H/IRH-1P Instrukcja obsługi

w innych językach

Powiązane artykuły

Inne dokumenty