Fast-Stat FSCM00 Instrukcja instalacji

Marka
Fast-Stat
Model
FSCM00
Typ
Instrukcja instalacji
Page 1 of 4 www.fast-stat.com
● The Common Maker provides a common connection
‘C’ for Wi-Fi and powered thermostats.
● A common connection allows the thermostat to
operate without batteries or “power stealing” circuits.
● The Common Maker is compatible with all 24V AC
heating and cooling systems.
1. Use the thermostat to turn ON the heating system,
and ensure that the heating system turns ON.
2. Use the thermostat to turn OFF the heating system,
and ensure that the heating system turns OFF.
1. Using a voltmeter, measure the voltage at the
transformer to ensure it is between 23 to 28 volts. If it
is outside this range the Common Maker may not work
as intended.
2. Ensure that the Sender purple wire and the Receiver
purple wire are connected through the existing
thermostat cable.
3. At the thermostat base, place a jumper wire between
the ‘R’ and ‘W’ terminals. This should cause the heating
system to start. If the heating system does not start,
the thermostat cable or Common Maker may be faulty.
4. Disconnect the Sender and bring it to the location of
the Receiver. While keeping the Receiver connected
to the equipment, connect the Sender and Receiver
purple wires together. Then apply 24V AC to the
Sender white wire. The relay in the Receiver should
energize. If the relay does not energize, the Common
Maker may be faulty.
● This product is designed for use with a Class 2
transformer providing 23 to 28 volts.
● The total connected load must not exceed 2 amps.
● The connected load cannot operate at more than 30
volts (not designed for direct connection to 120 volt
equipment).
● To avoid risk of electrical shock or equipment damage,
disconnect power before beginning installation.
The Sender is the smaller component and has purple,
white, and black wires. It is installed inside the wall behind
the thermostat.
The Receiver is the larger component and has purple,
white, black, and red wires. It is installed near the furnace,
boiler, air handler, zone valve, or zone controller. It should
be placed in the equipment cabinet or a location without
exposure to liquids or high temperatures.
Follow the relevant wiring diagram for your system (pages
2-4) and connect the wires accordingly. Additional wiring
diagrams may be found at www.fast-stat.com.
Note: The Sender will produce a small amount of heat
while operating. Keep the Sender wires as long as possible
to maximize the distance between the Sender and
thermostat. Do not install the Sender in insulated walls.
1. Remove the thermostat from its base.
2. The thermostat base will have wires running into the
wall through a small hole. If this hole is not big enough
to fit the Sender, enlarge the hole.
3. Find the wiring diagram for your system (pages 2-4)
and connect the wires accordingly.
4. Place the Sender in the wall. It will hang by its wires
and does not require any mounting.
5. Place the thermostat back on its base.
Overview
Testing
Troubleshooting
Internal Wiring
Contact Us
Electrical Safety
Sender Installation
Receiver Installation
After the Common Maker has been installed, check to see
if it is functioning properly by following these steps:
If the heating system failed to turn OFF, the power
consumption of the thermostat is too high, and therefore
incompatible with the Common Maker.
When the Sender has 24V AC applied to its white wire, it
will energize the relay in the Receiver, and complete the
circuit between the Receiver red and white wires. In most
installations, this will connect the ‘R’ and ‘W’ terminals on
the furnace.
For installation assistance, our technical support line can
be reached at 1-800-775-4750, 9am-5pm PST, or emailed
at info@nordictech.ca
The Common Maker also supports dry-contact switching.
In this configuration, the ‘T1’ and ‘T2’ terminals are
electrically isolated from the thermostat transformer.
Relay
W
C
W
C
R
R
Thermostat
Furnace
Sender
Purple
Purple
Black
Black
Red White
White
Relay
T
C
R
T
W
C
R
Thermostat
Controller
Sender
Purple Black
Black
Red White
White
Purple
Common Maker
Installation Instructions
Before
Before
After
After
Page 2 of 4 www.fast-stat.com
Thermostat
ControllerController
Sender
Purple
Common Maker
FAST-STAT
Receiver
Black
Red
White
Black
Purple
White
Thermostat
Thermostat
Cable
Thermostat
Cable
R C
W
R
W
T
R C
24V Transformer
T
Heat
TR C
24V Transformer
T
Heat
Thermostat
R C
W
R W
G
G
Sender
Purple
Common Maker
FAST-STAT
Receiver
Red
Black
White
Black
Purple
White
Thermostat
Cable
Thermostat
Cable
G
Thermostat
If your installation has additional
wires (G, Y, etc.), they can be
connected directly to the
furnace, boiler, or air handler.
W
Heat
R C
Furnace / Boiler / Air Handler
24V Transformer
G W
Heat
R C
Furnace / Boiler / Air Handler
24V Transformer
Dry Contact Switching with Internal TransformerB
Typical Installation for Furnaces, Boilers, and Air HandlersA
Before
Before
After
After
Page 3 of 4 www.fast-stat.com
Thermostat
TR TH
THTR
Sender
Purple
Common Maker
FAST-STAT
Receiver
Red
Black
White
Black
Purple
White
Gas Valve
R C
W
Thermostat
Cable
Thermostat
Cable
External Transformer
24V Transformer
TR TH
THTR
Gas Valve
External Transformer
24V Transformer
Thermostat
R W
Directly Connected Gas ValveD
Thermostat
Sender
Purple
Common Maker
FAST-STAT
Receiver
Black
Red
White
Black
Purple
White
Thermostat
If a 24V transformer is not
accessible, a new transformer will
have to be installed at the location
of the Common Maker Receiver.
R C
W
Thermostat
Cable
Thermostat
Cable
Equipment
T
T
Control
EquipmentExternal Transformer
T
T
Control
R W
24V Transformer
Dry Contact Switching with External TransformerC
Before
Before
After
After
Page 4 of 4 www.fast-stat.com
Zone Valve with Z-TV-W Aquastat (Varies by manufacturer - visit www.fast-stat.com for additional wiring diagrams)F
3 2 1
T
TV
Z
W
Aquastat
Sender
Purple
Common Maker
FAST-STAT
Common Maker
FAST-STAT
Receiver
Receiver
Red
Black
White
Black
Purple
White
Black
Purple
White
Purple
Red
Black
White
Thermostat
Cable
3 2 1
Thermostat
Cable
Thermostat Thermostat
3 2 1
T
TV
Z
W
Aquastat
Zone Valve
Zone Valve
Zone Valve
Zone Valve
Thermostat
Cable
3 2 1
Thermostat
Cable
Thermostat
W C
R
Thermostat
R
C
W
Sender
W R R W
R
W
Sender
Purple
Common Maker
FAST-STAT
Receiver
Red
Black
White
Black
Purple
White
Thermostat
Cable
Thermostat
TT
Control
Zone Valve
R
W
Thermostat
Cable
Thermostat
TT
Control
Zone Valve
C
External Transformer
24V Transformer
External Transformer
24V Transformer
Single Zone Valve with External TransformerE
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Fast-Stat FSCM00 Instrukcja instalacji

Marka
Fast-Stat
Model
FSCM00
Typ
Instrukcja instalacji
ściągnij PDF
raport

w innych językach

Powiązane dokumenty

Inne dokumenty