FRAMTID
HGA5K
GB
PL
PL
PL
PL
ENGLISH 4
POLSKI 18
Language, Język
Country, Kraj
Contents
Safety instructions 5
Product description 7
Daily use 7
Helpful hints and tips 8
Care and cleaning 9
What to do if… 10
Technical data 10
Installation 12
Environment concerns 15
IKEA GUARANTEE 15
Subject to change without notice.
Before the installation and use of the appliance, carefully read
the supplied instructions. The manufacturer is not responsible if
an incorrect installation and use causes injuries and damages.
Always keep the instructions with the appliance for future refer-
ence.
Children and vulnerable people safety
Warning! Risk of suffocation, injury or permanent disability.
• This appliance can be used by children aged from 8 years
and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if
they are supervised by an adult or a person who is responsi-
ble for their safety.
• Do not let children play with the appliance.
• Keep all packaging away from children.
• Keep children and pets away from the appliance when it op-
erates or when it cools down. Accessible parts are hot.
• Cleaning and user maintenance shall not be made by chil-
dren without supervision.
General Safety
• The appliance and its accessible parts become hot during
use. Do not touch the heating elements.
• Do not operate the appliance by means of an external timer
or separate remote-control system.
• Unattended cooking on a hob with fat or oil can be danger-
ous and may result in fire.
ENGLISH 4
• Never try to extinguish a fire with water, but switch off the
appliance and then cover flame e.g. with a lid or a fire blan-
ket.
• Do not store items on the cooking surfaces.
• Do not use a steam cleaner to clean the appliance.
• Metallic objects such as knives, forks, spoons and lids should
not be placed on the hob surface since they can get hot.
Safety instructions
Installation
Warning! Only a qualified person must
install this appliance.
• Remove all the packaging.
• Do not install or use a damaged appli-
ance.
• Obey the installation instruction supplied
with the appliance.
•Always be careful when you move the
appliance because it is heavy. Always
wear safety gloves.
• Seal the cut surfaces with a sealant to
prevent moisture to cause swelling.
• Protect the bottom of the appliance from
steam and moisture.
• Do not install the appliance adjacent to a
door or under a window. This prevents
hot cookware to fall from the appliance
when the door or the window is opened.
• Keep the minimum distance from the oth-
er appliances and units. Refer to the as-
sembly instructions.
• If the appliance is installed above draw-
ers make sure that the space, between
the bottom of the appliance and the up-
per drawer, is sufficient for air circulation.
Refer to the assembly instructions.
• The bottom of the appliance can get hot.
We recommend to install a non-combus-
tile separation panel under the appliance
to prevent access to the bottom.
Electrical connection
Warning! Risk of fire and electrical
shock.
• All electrical connections must be made
by a qualified electrician.
• The appliance must be earthed.
• Before carrying out any operation make
sure that the appliance is disconnected
from the power supply.
• Use the correct electricity mains cable.
• Do not let the electricity mains cable tan-
gle.
• Make sure the mains cable or plug (if ap-
plicable) does not touch the hot appli-
ance or hot cookware, when you connect
the appliance to the near sockets
• Make sure the appliance is installed cor-
rectly. Loose and incorrect electricity
mains cable or plug (if applicable) can
make the terminal become too hot.
• Make sure that a shock protection is in-
stalled.
• Use the strain relief clamp on cable.
• Make sure not to cause damage to the
mains plug (if applicable) or to the mains
cable. Contact the Service or an electri-
cian to change a damaged mains cable.
• The electrical installation must have an
isolation device which lets you disconnect
the appliance from the mains at all poles.
The isolation device must have a contact
opening width of minimum 3 mm.
• Use only correct isolation devices: line
protecting cut-outs, fuses (screw type
fuses removed from the holder), earth
leakage trips and contactors.
ENGLISH 5
Gas connection
• All gas connections should be made by a
qualified person.
• Make sure that there is air circulation
around the appliance.
• The information about the gas supply is
on the rating plate.
• This appliance is not connected to a de-
vice, which evacuates the products of
combustion. Make sure to connect the
appliance according to current installa-
tion regulations. Pay attention to require-
ments regarding adequate ventilation.
Use
Warning! Risk of injury, burns or
electric shock.
• Use this appliance in a household envi-
ronment.
• Do not change the specification of this
appliance.
• Do not let the appliance stay unattended
during operation.
• Do not operate the appliance with wet
hands or when it has contact with water.
• Do not put cutlery or saucepan lids on the
cooking zones. They become hot.
• Set the cooking zone to “off” after use.
Warning! Risk of fire or explosion.
• Fats and oil when heated can release
flammable vapours. Keep flames or heat-
ed objects away from fats and oils when
you cook with them.
• The vapours that very hot oil releases can
cause spontaneous combustion
•Used oil, that can contain food remnants,
can cause fire at a lower temperature
than oil used for the first time.
• Do not put flammable products or items
that are wet with flammable products in,
near or on the appliance.
Warning! Risk of damage to the
appliance.
• Do not keep hot cookware on the control
panel.
• Do not let cookware to boil dry.
• Do not activate the cooking zones with
empty cookware or without cookware.
• Be careful not to let objects or cookware
fall on the appliance. The surface can be
damaged.
• Do not put aluminium foil on the appli-
ance.
• Do not let acid liquids, for example vine-
gar, lemon juice or limescale remover
touch the hob. This can cause matt patch-
es.
• Provide good ventilation in the room
where the appliance is installed.
• Make sure that the ventilation openings
are not blocked.
• Use only stable cookware with the correct
shape and diameter larger than the di-
mensions of the burners. There is a risk of
overheating and rupture of the glass
plate (if applicable).
• Make sure the flame does not go out
when you quickly turn the knob from the
maximum to the minimum position.
• Make sure pots are centrally positioned
on the rings and do not stick out over
edges of the cooking surface.
• Use only the accessories supplied with
the appliance.
• Do not install a flame diffuser on the
burner.
Care and Cleaning
Warning! Risk of damage to the
appliance.
• Clean regularly the appliance to prevent
the deterioration of the surface material.
• Do not use water spray and steam to
clean the appliance.
• Do not clean the burners in the dishwash-
er.
• Clean the appliance with a moist soft
cloth. Only use neutral detergents. Do not
use abrasive products, abrasive cleaning
pads, solvents or metal objects.
Disposal
Warning! Risk of injury or suffocation.
ENGLISH 6
• Contact your municipal authority for in-
formation on how to discard the appli-
ance correctly.
• Disconnect the appliance from the mains
supply.
• Cut off the mains cable and discard it.
• Flat the external gas pipes.
Product description
1 4 5
678910
2 3
1112
1
Ultra-rapid burner
2
Semi-rapid burner (rear)
3
Semi-rapid burner (front)
4
Rapid burner
5
Auxiliary burner
6
Rapid burner control knob
7
Auxiliary burner control knob
8
Semi-rapid burner control knob (rear)
9
Semi-rapid burner control knob (front)
10
Ultra-Rapid burner control knob
11
Removable pan support
12
Wok stand
Burner control knob
The burner control knobs are situated on
the front of the hob.
Symbol Description
there is no gas supply / off
position
there is maximum gas sup-
ply / Ignition setting
there is minimum gas sup-
ply
Daily use
Ignition of the burners
Always ignite the burners before posi-
tioning pots or pans.
To ignite the burner:
1. Push the relevant control knob com-
pletely in and turn it counter-clockwise
to the maximum position marked
.
2. Keep the knob pushed for about 5 sec;
this will allow thermocouple to heat up,
and the safety device to switch off, oth-
erwise the gas supply would be inter-
rupted.
3. After the flame is regular, adjust it as
preferred.
If after a few attempts the burner does
not ignite, check that the crown and its
cap are in correct positions.
ENGLISH 7
3
4
2
1
1
2
3
4
1
Burner cap
2
Burner crown
3
Ignition candle
4
Thermocouple
Warning! Do not keep control knob
pressed for more than 15 seconds.
If the burner does not light after 15 seconds,
release the control knob, turn it into off posi-
tion and wait for at least 1 minute before
trying to light the burner again.
Important! In the absence of electricity You
can ignite the burner without electrical
device; in this case approach the burner
with a flame, push the relevant knob down
and turn it counter-clockwise to maximum
gas release position.
Warning! Maintain extreme caution
while operating with open fire in
kitchen environment. Manufacturer declines
any responsibility in case of misuse of flame.
If the burner accidentally goes out, turn
the control knob to the off position and
wait for at least 1 minute before trying to
light it again.
When switching on the mains, after in-
stallation or a power cut, it is quite nor-
mal for the spark generator to be activated
automatically.
Turning the burners off
To put the flame out, turn the relevant con-
trol knob to the symbol
.
Warning! Always turn the flame down
or switch it off before removing the
pans of the burner.
Using the Wok Stand
A wok stand is provided to enable you to
use a round bottomed wok on the hob. The
wok stand must only be used on the ultra
rapid burner, and should not be used with
any other type of wok or pan. When fitting
the wok stand, ensure the recesses in the
frame fit securely onto the bars of the pan
supports, as shown in the picture.
Helpful hints and tips
Energy savings
• If possible, always place lids on the pans.
• As soon as liquid starts boiling, turn down
the flame to barley keep the liquid sim-
mering.
Use pots and pans with bottom fitting the
size of burner used.
ENGLISH 8
Burner minimum di-
ameter of
pots and pans
maximum di-
ameter of
pots and pans
Ultra-
rapid
180 mm 280 mm
Rapid 180 mm 260 mm
Semi-
rapid
(rear)
120 mm 220 mm
Burner minimum di-
ameter of
pots and pans
maximum di-
ameter of
pots and pans
Semi-
rapid
(front)
120 mm 180 mm
Auxili-
ary
80 mm 180 mm
The bottom of the cookware should be as
thick and flat as possible.
Care and cleaning
Warning! Switch the appliance off and
let it cool down before you clean it.
Warning! For safety reasons, do not
clean the appliance with steam
blasters or high-pressure cleaners.
Warning! Do not use abrasive
cleaners, steel wool pads or acids, they
will damage the appliance.
To remove any food remains wash the
enamelled elements, "caps" and "crowns",
with warm soapy water.
Stainless steel elements wash with water,
and then dry with a soft cloth.
This model is equipped with electrical igni-
tion, it is obtained through ceramic "candle"
with electrode.
Keep them well clean to avoid difficult light-
ning.
The pan supports are not dishwasher proof;
they must be washed by hand. After clean-
ing, make sure that the pan supports are
correctly positioned.
To make burners work correctly, make sure
that the arms of the pan supports are in the
centre of the burner.
225 mm 245 mm
Periodically ask your local Service Cen-
tre to check the conditions of the gas
supply pipe and the pressure adjuster, if it is
fitted (this service is not free of charge).
After cleaning, be sure to wipe dry with a
soft cloth.
ENGLISH 9
What to do if…
Problem Possible cause Remedy
There is no spark when
lighting the gas
There is no electrical supply Check that the unit is plug-
ged in and the electrical
supply is switched on.
There is no electrical supply Check the house electric in-
stallation fuse.
Burner cap and Crown are
placed uneven
Check the burner cap and
crown have been replaced
correctly, e.g. after cleaning.
The flame is blowing out im-
mediately after lightning
Thermocouple is not heated
enough
After lightning the flame,
keep the knob pushed for
about 5 sec.
The gas ring burns unevenly Burner crown is blocked with
food residues
Check the main injector is
not blocked and the burner
crown is clear of food parti-
cles.
If there is a fault, first try to find a solution to
the problem yourself. If you cannot find a
solution to the problem yourself, contact the
After Sales Service (refer to the Service
chapter).
If you operated the appliance wrongly,
or the installation was not carried out
by a registered engineer, the visit from the
customer service technician or dealer may
not take place free of charge, even during
the warranty period.
Technical data
Hob dimensions
width 744 mm
depth 510 mm
built in height 30 mm
Class Appliance: 3
Appliance Category: II2ELs3B/P
Appliance gas supply: Natural gas G20 (2E)
20 mbar
This appliance is designed for use with nat-
ural gas but can be converted for use with
other gas type according to table below.
Type of Gas
Burner
type
Injectors
1/100
mm
Nominal
Power
kW
Nominal
Flow g/h
Reduced
Power kW
by-pass
1/100 mm
G20 (2E) 20
mbar
Ultra-
rapid
(large)
146 4.0 - 1.4 52
Rapid 119 3.0 - 0.75 40
ENGLISH 10
Type of Gas
Burner
type
Injectors
1/100
mm
Nominal
Power
kW
Nominal
Flow g/h
Reduced
Power kW
by-pass
1/100 mm
Semi-
rapid
96 2.0 - 0.45 30
Auxiliary
(small)
70 1.0 - 0.33 26
G2.350
(2ELs) 13
mbar
Ultra-
rapid
(large)
205 (no
regulator)
4.0 - 1.4 52
Rapid
181 (big
regulator)
3.0 - 0.75 40
Semi-
rapid
150
(small
regulator)
2.0 - 0.45 30
Auxiliary
(small)
105
(small
regulator)
1.0 - 0.33 26
G30/G31
(3B/P)
37/37 mbar
Ultra-
rapid
(large)
095 4.0 291 1.4 52
Rapid 80 2.8 204 0.75 40
Semi-
rapid
066 2.0 145 0.45 30
Auxiliary
(small)
46 1.0 73 0.33 26
Rating Plate
000-000-00
Made In Italy
© Inter IKEA Systems B.V. 1999
21552
PQM
PNC. 000000000 TYPE 00000000-0/00
G00 00 mbar = 00 kW
G00 00 mbar = 00 g/h
230 V
~
50 Hz
ZO 0694
The graphic above represents the rating
plate of the appliance (without serial num-
ber which is generated dynamically during
the production process), which is located at
its underneath surface of the casing.
Dear Customer, please apply here aside
the sticker you can find in the dedicate
plastic bag inserted inside the hob packag-
ing. This will allow us to assist you better, by
identifying precisely your hob, in case you
will need in future our assistance. Thank you
for your help!
ENGLISH 11
Installation
Warning! This appliance must be
installed, connected or repaired only
by a registered competent person to the
relevant gas standard. Use only parts
provided with the product. Use only original
spare parts.
Manufacturer is not responsible for any in-
jury to persons and pets or damage to
property caused by failure to comply fol-
lowing requirements.
Caution! To proceed with the
installation refer to the assembly
instructions.
Warning! Installation process must
follow the laws, ordinances, directives
and standards (electrical safety rules and
regulations, proper recycling in accordance
with the regulations, etc.) in force in the
country of use!
Ensure that the local distribution condi-
tions (nature of the gas and gas pres-
sure) and the adjustment of the appliance
are compatible before proceeding with the
installation.
The parameters of adjustment setting
for this appliance are stated on the
rating plate (refer to the Technical data
chapter).
Warning! The appliance must be
earthed!
Warning! Risk of injury from electrical
current.
• The electrical mains terminal is live.
• Make electrical mains terminal free of
voltage.
• Loose and inappropriate plug and socket
connections can make the terminal over-
heat.
• Have the clamping connections correctly
installed.
• Use strain relief clamp on cable.
Important! You must observe the minimum
distances to other appliances and furniture
cabinets or other units according to
Assembly Instruction.
If there is no oven beneath the hob insert a
dividing panel at a minimum distance of 20
mm from the bottom of the hob.
Protect the cut surfaces of the worktop
against moisture using a suitable sealant in-
cluded in the product in fitting bag. The
sealant seals the appliance to the work top
with no gap. Do not use silicon sealant be-
tween the appliance and the worktop.
Avoid installing the appliance next to doors
and under windows as hot cookware may
be knocked off the pan support when doors
and windows are opened.
Gas Connection
Warning! Only a qualified person must
install this appliance.
Warning! This appliance is not
connected to a combustion products
evacuation device.
Installation must comply with current local
regulation.
ENGLISH 12
The connection of the cooktop to the gas
pipe network or gas cylinder must be made
by means of a rigid copper or steel pipe
with fittings complying with local regula-
tions, or by means of a continuous surface
stainless steel hose complying with local
regulations.
If you see any abnormalities do not re-
pair the pipe, contact local After Sales
Service (refer to the Service chapter).
The connection must be installed correctly,
fixed into hob connection pipe. Otherwise it
will cause leakage of gas
Warning! Once the installation is
complete, check the perfect seal of
every pipe fixing. Use soapy water, never
flame.
Electrical connection
Before connecting, check that the nominal
voltage of the appliance stated on the rat-
ing plate, corresponds to the available sup-
ply voltage. Also, check the power rating of
the appliance and ensure that the wire is
suitably sized to suit the appliance power
rating (refer to the Technical data chapter).
The rating plate is located on the lower cas-
ing of the hob.
The appliance is supplied with a connection
cable. This has to be provided with a prop-
er plug, able to support the load marked on
the identification plate (refer to the Techni-
cal data chapter).
The plug has to be fitted in a proper socket.
If connecting the appliance directly to the
electric system, it is necessary that you in-
stall a double pole switch between the ap-
pliance and the electricity supply, with a
minimum gap of 3 mm between the switch
contacts. The double pole has to be of a
type suitable for the required load in com-
pliance with the current rules.
The connection cable has to be placed in
order that, in each part, it cannot reach a
90 °C temperature. The blue neutral cable
must be connected to the terminal block
marked with "N". The brown (or black)
phase cable (fitted in the terminal block
contact marked with "L") must always be
connected to the live phase.
Replacement of the connection cable.
Warning! The replacement of electric
cable must be carried out exclusively
by the After Sales Service or by personnel
with similar competencies, in accordance
with the current regulations.
If the connection cable must be replaced,
only a type H05V2V2-F T90 cable must be
used. The cable section must be suitable to
the voltage and the working temperature.
The yellow/green earth wire must be ap-
proximately 2 cm longer than the brown (or
black) phase wire.
Gas setting conversion
This model is designed for use with
natural gas but can be converted for
use with butane or propane gas providing
the correct injectors. The injectors not sup-
plied with the appliance have to be or-
dered from After Sales Service (refer to the
Service chapter).
For data concerning injector replacement,
refer to the chapter Technical data
Warning! Conversion or replacement
can only be performed by a registered
installer.
To replace injectors:
1. Remove pan support.
2. Remove burner cap and crown.
3. With a socket spanner 7 unscrew and
remove the injectors, replace them with
the ones required for the type of gas in
use.
4. Reassemble the parts, following the
same procedure backwards.
ENGLISH 13
Important! Replace the rating label (placed
near gas supply pipe) with relevant one for
the new type of gas supply before sealing
the appliance. If the appliance is already
sealed please stick it directly on the user
manual booklet after Technical data
chapter close to the rating plate drawing.
You can find this label in package sup-
plied with appliance
If the feeding gas pressure will be dif-
ferent or variable, comparing with the
required, you must install an appropriate
pressure adjuster, which is not supplied with
the product and if needed must be ordered
separately from the local After Sales Service
(refer to the Service chapter). The pressure
adjuster must be fitted on gas supply pipe,
in compliance with the rules of the force.
The rating plate is located on the lower cas-
ing of the hob.
Conversion to G2.350 gas
• Auxiliary and semi-rapid burner: after
you assembly the injectors (
3
in follow-
ing figure), screw their cages (diameter
10 mm,
1
in following figure) on, inclu-
ded in the supply (primary air regula-
tors) ;
• Rapid burner: after assembly the injectors
(
3
in following figure), screw their cages
(diameter 16 mm,
2
in following figure)
on, included in the supply (primary air
regulators) ;
1
2
4
3
Important! In both cases use the special
cap tool
4
and a screwdriver to secure the
cages.
Important! Be sure to remove the cap tool
before reassembling the burners.
Adjusting flame level
When hob has been fully installed, it is nec-
essary to check the minimum flame setting:
1. Turn the gas tap to the maximum posi-
tion and ignite.
2. Set the gas tap to the minimum flame
position then turn the control knob from
minimum to maximum several times. If
the flame is unstable or extinguished,
follow the procedure further.
3. Re-ignite the burner and set to mini-
mum.
4. Remove the control knob.
5. To adjust, use a thin bladed screwdriver
and turn the adjustment screw until the
flame is steady and does not extin-
guish, when the knob is turned from
minimum to maximum, and vice versa
(see following picture).
ENGLISH 14
6. Repeat this procedure for all burners.
7. Reassemble the knobs.
Warning! If the appliance is connected
to liquid gas (G31 propane or G30
butane), the regulation screw must be
fastened as tightly as possible.
IKEA of Sweden AB
SE-34381 Älmhult
Environment concerns
The symbol on the product or on its
packaging indicates that this product may
not be treated as household waste. Instead
it should be taken to the appropriate
collection point for the recycling of electrical
and electronic equipment. By ensuring this
product is disposed of correctly, you will
help prevent potential negative
consequences for the environment and
human health, which could otherwise be
caused by inappropriate waste handling of
this product. For more detailed information
about recycling of this product, please
contact your local council, your household
waste disposal service or the shop where
you purchased the product.
Packaging materials
The materials with the symbol
are recy-
clable. Dispose the packaging in a suitable
collection containers to recycle it.
Before disposal of appliance
Warning! Do these steps to dispose
the appliance:
• Pull the mains plug out of the mains sock-
et.
• Cut off the mains cable and discard it.
IKEA GUARANTEE
How long is the IKEA guarantee valid?
This guarantee is valid for five (5) years
from the original date of purchase of Your
appliance at IKEA, unless the appliance is
named LAGAN in which case two (2) years
of guarantee apply. The original sales re-
ceipt is required as proof of purchase. If
service work is carried out under guarantee,
this will not extend the guarantee period for
the appliance,
Which appliances are not covered by the
IKEA five (5) years guarantee?
The range of appliances named LAGAN
and all appliances purchased in IKEA be-
fore 1st of August 2007
Who will execute the service?
IKEA service provider will provide the serv-
ice through its own service operations or
authorized service partner network.
ENGLISH 15
What does this guarantee cover?
The guarantee covers faults of the appli-
ance, which have been caused by faulty
construction or material faults from the date
of purchase from IKEA. This guarantee ap-
plies to domestic use only. The exceptions
are specified under the headline “What is
not covered under this guarantee?” Within
the guarantee period, the costs to remedy
the fault e.g. repairs, parts, labour and trav-
el will be covered, provided that the appli-
ance is accessible for repair without special
expenditure. On these conditions the EU
guidelines (Nr. 99/44/EG) and the respec-
tive local regulations are applicable. Re-
placed parts become the property of IKEA.
What will IKEA do to correct the problem?
IKEA appointed service provider will exam-
ine the product and decide, at its sole dis-
cretion, if it is covered under this guarantee.
If considered covered, IKEA service provider
or its authorized service partner through its
own service operations, will then, at its sole
discretion, either repair the defective prod-
uct or replace it with the same or a compa-
rable product.
What is not covered under this
guarantee?
• Normal wear and tear.
• Deliberate or negligent damage, dam-
age caused by failure to observe operat-
ing instructions, incorrect installation or by
connection to the wrong voltage, dam-
age caused by chemical or electro-chem-
ical reaction, rust, corrosion or water
damage including but not limited to dam-
age caused by excessive lime in the wa-
ter supply, damage caused by abnormal
environmental conditions.
• Consumable parts including batteries
and lamps.
• Non-functional and decorative parts
which do not affect normal use of the ap-
pliance, including any scratches and pos-
sible color differences.
• Accidental damage caused by foreign
objects or substances and cleaning or un-
blocking of filters, drainage systems or
soap drawers.
• Damage to the following parts: ceramic
glass, accessories, crockery and cutlery
baskets, feed and drainage pipes, seals,
lamps and lamp covers, screens, knobs,
casings and parts of casings. Unless such
damages can be proved to have been
caused by production faults.
• Cases where no fault could be found dur-
ing a technician’s visit.
• Repairs not carried out by our appointed
service providers and/or an authorized
service contractual partner or where non-
original parts have been used.
• Repairs caused by installation which is
faulty or not according to specification.
• The use of the appliance in a non-domes-
tic environment i.e. professional use.
• Transportation damages. If a customer
transports the product to their home or
other address, IKEA is not liable for any
damage that may occur during transport.
However, if IKEA delivers the product to
the customer's delivery address, then
damage to the product that occurs during
this delivery will be covered by this guar-
antee.
• Cost for carrying out the initial installation
of the IKEA appliance. However, if an
IKEA service provider or its authorized
service partner repairs or replaces the
appliance under the terms of this guaran-
tee, the service provider or its authorized
service partner will re-install the repaired
appliance or install the replacement, if
necessary.
This restriction do not apply to fault-free
work carried out by a qualified specialist
using our original parts in order to adapt
the appliance to the technical safety specifi-
cations of another EU country.
How country law applies
The IKEA guarantee gives You specific legal
rights, which covers or exceed local de-
mands. However these conditions do not
limit in any way consumer rights described
in the local legislation
ENGLISH 16
Area of validity
For appliances which are purchased in one
EU country and taken to another EU coun-
try, the services will be provided in the
framework of the guarantee conditions nor-
mal in the new country. An obligation to
carry out services in the framework of the
guarantee exists only if the appliance com-
plies and is installed in accordance with:
• the technical specifications of the country
in which the guarantee claim is made;
• the Assembly Instructions and User Man-
ual Safety Information;
The dedicated After Sales Service for
IKEA appliances:
Please do not hesitate to contact IKEA After
Sales Service to:
1. make a service request under this guar-
antee;
2. ask for clarification on installation of the
IKEA appliance in the dedicated IKEA
kitchen furniture. The service won’t pro-
vide clarifications related to:
– the overall IKEA kitchen installation;
– connections to electricity (if machine
comes without plug and cable), to
water and to gas since they have to
be executed by an authorized serv-
ice engineer.
3. ask for clarification on user manual con-
tents and specifications of the IKEA ap-
pliance.
To ensure that we provide you with the best
assistance, please read carefully the As-
sembly Instructions and/or the User Manual
section of this booklet before contacting us.
How to reach us if You need our service
Please refer to the last page of this manual
for the full list of IKEA appointed contacts
and relative national phone numbers.
Important! In order to provide You with a
quicker service, we recommend that You
use the specific phone numbers listed at the
end of this manual. Always refer to the
numbers listed in the booklet of the specific
appliance You need an assistance for.
Before calling us, assure that You have to
hand the IKEA article number (8 digit code)
for the appliance of which you need our
assistance.
Important! SAVE THE SALES RECEIPT! It is
Your proof of purchase and required for the
guarantee to apply. Note that the receipt
reports also the IKEA article name and
number (8 digit code) for each of the
appliances you have purchased.
Do You need extra help?
For any additional questions not related to
After Sales of your appliances, please con-
tact our nearest IKEA store call centre. We
recommend you read the appliance docu-
mentation carefully before contacting us.
ENGLISH 17
Spis treści
Wskazówki dotyczące bezpieczeństwa
19
Opis urządzenia 22
Codzienna eksploatacja 22
Przydatne rady i wskazówki 24
Konserwacja i czyszczenie 24
Co zrobić, gdy… 25
Dane techniczne 25
Instalacja 27
Ochrona środowiska 30
GWARANCJA IKEA 31
Producent zastrzega sobie możliwość wprowadzenia zmian bez wcześniejszego
powiadomienia.
Przed instalacją i rozpoczęciem eksploatacji urządzenia należy
uważnie zapoznać się z załączoną instrukcją obsługi. Produ-
cent nie odpowiada za uszkodzenia i obrażenia ciała spowo-
dowane nieprawidłową instalacją i eksploatacją. Należy za-
chować instrukcję wraz z urządzeniem do wykorzystania w
przyszłości.
Bezpieczeństwo dzieci i osób o ograniczonych
zdolnościach ruchowych, sensorycznych lub umysłowych
Ostrzeżenie! Występuje zagrożenie uduszeniem lub
odniesieniem obrażeń mogących skutkować trwałym
kalectwem.
• Urządzenie mogą obsługiwać dzieci po ukończeniu ósmego
roku życia oraz osoby o ograniczonych zdolnościach fizycz-
nych, sensorycznych lub umysłowych bądź nieposiadające
odpowiedniej wiedzy i doświadczenia, jeśli będą one nad-
zorowane przez dorosłą osobę lub osobę odpowiedzialną
za ich bezpieczeństwo.
•Nie należy pozwalać, aby dzieci bawiły się urządzeniem.
• Wszystkie opakowania należy przechowywać poza zasię-
giem dzieci.
• Dzieci i zwierzęta nie powinny zbliżać się do pracującego
lub stygnącego urządzenia. Ł
atwo dostępne elementy urzą-
dzenia mocno się nagrzewają.
• Czyszczeniem i konserwacją nie mogą zajmować się dzieci
bez nadzoru dorosłych.
POLSKI 18
Ogólne zasady bezpieczeństwa
• Urządzenie oraz jego nieosłonięte elementy nagrzewają się
podczas pracy do wysokiej temperatury. Nie dotykać ele-
mentów grzejnych.
• Nie sterować urządzeniem za pomocą zewnętrznego zegara
ani niezależnego układu zdalnego sterowania.
• Pozostawienie bez nadzoru potraw zawierających tłuszcz
lub olej na włączonej płycie grzejnej może być przyczyną
pożaru.
•Nie gasić pożaru wodą – należy wyłączyć urządzenie, a na-
stępnie przykryć płomień pokrywą lub kocem gaśniczym.
• Nie przechowywać żadnych przedmiotów na powierzchni
gotowania.
•Nie czyścić urządzenia za pomocą myjek parowych.
•Na powierzchni płyty grzejnej nie wolno kłaść przedmiotów
metalowych, takich jak sztućce lub pokrywki do garnków, po-
nieważ mogą one bardzo się rozgrzać.
Wskazówki dotyczące bezpieczeństwa
Instalacja
Ostrzeżenie! Urządzenie może
zainstalować wyłącznie
wykwalifikowana osoba.
•Usunąć wszystkie elementy opakowania.
•Nie instalować ani nie używać uszkodzo-
nego urządzenia.
•Postępować zgodnie z instrukcją instala-
cji załączoną do urządzenia.
•Zachować ostrożność podczas przeno-
szenia urządzenia, ponieważ jest ono
ciężkie. Zawsze używać rękawic ochron-
nych.
•Po przycięciu zabezpieczyć krawędzie
blatu przed wilgocią za pomocą odpo-
wiedniego uszczelniacza.
•Zabezpieczyć spód urządzenia przed
dostępem pary i wilgoci.
•Nie instalować urządzenia przy drzwiach
ani pod oknem. Zapobiegnie to możli-
wości strącenia gorącego naczynia z
urządzenia przy otwieraniu okna lub
drzwi.
•Zachować minimalne odstępy od innych
urządzeń i mebli. Należy zapoznać się z
instrukcją montażu.
• Instalując urządzenie nad szufladami na-
leży zapewnić wystarczająco dużo miejs-
ca między dolną częścią urządzenia a
górną szufladą, aby umożliwić prawidło-
wy obieg powietrza. Należy zapoznać
się z instrukcją montażu.
• Spód urządzenia może się mocno na-
grzewać. Zaleca się zamontowanie pod
urzą
dzeniem niepalnej płyty uniemożli-
wiającej dostęp do urządzenia od spodu.
POLSKI 19
Podłączenie do sieci elektrycznej
Ostrzeżenie! Występuje zagrożenie
pożarem i porażeniem prądem
elektrycznym.
•Wszystkie połączenia elektryczne musi
wykonać wykwalifikowany elektryk.
•Urządzenie musi być uziemione.
• Przed wykonaniem jakiejkolwiek czyn-
ności upewnić się, że urządzenie jest od-
łączone od zasilania.
•Użyć odpowiedniego przewodu zasilają-
cego.
• Nie dopuszczać do splątania przewodów
elektrycznych.
•Podczas podłączania urządzenia do
gniazda sieciowego upewnić się, że
przewód zasilający lub jego wtyczka (je-
śli dotyczy) nie będzie dotykać rozgrza-
nych elementów urządzenia lub naczyń.
•Upewnić się, że urządzenie jest prawid-
łowo zainstalowane. Luźny lub niewła
ści-
wy przewód zasilający bądź wtyczka (je-
śli dotyczy) może być przyczyną prze-
grzania styków.
•Upewnić się, że zostało zainstalowane
zabezpieczenie przed porażeniem prą-
dem.
•Przewód zasilający należy przymocować
obejmą w celu jego mechanicznego od-
ciążenia.
•Należy uważać, aby nie uszkodzić wtycz-
ki (jeśli dotyczy) ani przewodu zasilające-
go. Wymianę uszkodzonego przewodu
zasilającego należy zlecić przedstawicie-
lowi serwisu lub wykwalifikowanemu
elektrykowi.
• W instalacji elektrycznej należy zastoso-
wać wyłącznik obwodu umożliwiający
odłączenie urządzenia od zasilania na
wszystkich biegunach. Wyłącznik obwo-
du musi mieć rozwarcie styków wynoszą-
ce minimum 3 mm.
• Konieczne jest zastosowanie odpowied-
nich wyłączników obwodu zasilania: wy-
łączniki automatyczne, bezpieczniki topi-
kowe (typu wykręcanego — wyjmowane
z oprawki), wyłączniki różnicowo-prądo-
we (RCD) oraz styczniki.
Podłączenie do instalacji gazowej
•Wszystkie połączenia instalacji gazowej
powinna wykonać wykwalifikowana oso-
ba.
•Zapewnić cyrkulację powietrza wokół
urządzenia.
• Informacje dotyczące dopływu gazu
znajdują się na tabliczce znamionowej.
•Omawiane urządzenie nie jest podłączo-
ne do wyciągu gazów spalinowych.
Urządzenie należy podłączyć zgodnie z
aktualnie obowiązującymi przepisami
dotyczącymi instalacji. Zwrócić uwagę na
wymagania dotyczące odpowiedniej
wentylacji.
Przeznaczenie
Ostrzeżenie! Niebezpieczeństwo
odniesienia obrażeń ciała, oparzenia,
porażenia prądem.
•Urządzenie należy używać w warunkach
domowych.
• Nie zmieniać parametrów technicznych
urządzenia.
• Nie pozostawiać włą
czonego urządzenia
bez nadzoru.
•Nie obsługiwać urządzenia mokrymi rę-
kami lub jeśli ma ono kontakt z wodą.
•Nie kłaść sztućców ani pokrywek naczyń
na polach grzejnych. Pola grzejne mocno
się nagrzewają.
•Po każdym użyciu wyłączyć pole grzejne.
Ostrzeżenie! Występuje zagrożenie
pożarem lub wybuchem.
•Pod wpływem wysokiej temperatury
tłuszcze i olej mogą uwalniać łatwopalne
opary. Podczas podgrzewania tłuszczów
i oleju nie wolno zbliżać do nich źródeł
ognia ani rozgrzanych przedmiotów.
• Opary uwalniane przez gorący olej mo-
gą ulec samoczynnemu zapłonowi.
•Zużyty olej zawierający pozostałości pro-
duktów spożywczych ma niższą tempera-
turę zapłonu niż świeży olej.
•Nie umieszczać w urządzeniu, na nim ani
w jego pobliżu łatwopalnych substancji
ani przedmiotów nasączonych łatwopal-
nymi substancjami.
POLSKI 20
Strona jest ładowana ...
Strona jest ładowana ...
Strona jest ładowana ...
Strona jest ładowana ...
Strona jest ładowana ...
Strona jest ładowana ...
Strona jest ładowana ...
Strona jest ładowana ...
Strona jest ładowana ...
Strona jest ładowana ...
Strona jest ładowana ...
Strona jest ładowana ...
Strona jest ładowana ...
Strona jest ładowana ...
Strona jest ładowana ...
Strona jest ładowana ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
w innych językach
- English: IKEA FHGA5K 502-007-04 User manual
Powiązane dokumenty
-
IKEA FHGA1K Instrukcja obsługi
-
-
-
-
-
IKEA LHGA4K Instrukcja obsługi
-
-
-
-