Barska AC12449 Instrukcja obsługi

Typ
Instrukcja obsługi

Ten podręcznik jest również odpowiedni dla

LIMITED LIFETIME WARRANTY
BARSKA® Optics, as manufacturer, warrants this new precision optical product
to be free of original defects in materials and/or workmanship for the length of
time specied by this warranty. This warranty does not include damage caused
by abuse, improper handling, installation, maintenance, normal wear-and-tear,
unauthorized repairs or modications and tampering in anyway.
This warranty is limited to the original purchaser and is not transferable. This
warranty applies only to products purchased in the United States of America
and Canada.
In the event of a defect within 30 days, the consumer must return the defective
unit to the BARSKA dealer (the place of purchase) at his/her own expense.
Beyond 30 days, BARSKA products should be sent to the following address
for warranty repairs. Products must be packed carefully and sturdily to prevent
damage in transit, and returned freight prepaid to:
BARSKA® OPTICS
Repair Department
855 Towne Center Drive
Pomona, CA 91767
For additional and updated information
please visit our website at www.barska.com
Please email [email protected] or call 1-888-666-6769 for Return Merchandise
Number (RMA#) before any returns.
NOTE: All merchandise received without a valid RMA # will be returned to
shipper at his/her own expense.
Please include all of the following when returning BARSKA products for service
and/or replacement:
1. Please write your complete details (Name, Address, Telephone #,
E-mail address, RMA#, etc.)
2. Purchase receipt or Proof of Purchase. (Original/Copy)
3. A brief explanation of the defect.
4. A Check/Money Order of $25.00 to cover inspection, shipping and handling.
*Please allow 6-8 weeks for delivery.
This product will either be replaced or repaired at the discretion of the
warrantor. If it’s a discontinued item, we will replace the product with an
equivalent product. Should the repair not be covered by this warranty, an
estimate will be sent for your approval. Non-warranty repairs or refurbishing of
your optical products are always provided at a reasonable cost.
BARSKA® Optics shall not be liable for any consequential, incidental and/or
contingent damages whatsoever. We will not pay shipping, insurance or
transportation charges from you to us, or any import fees, duties and or taxes.
This warranty supersedes all previous BARSKA® Optics warranties.
©
2015 BARSKA
®
BC293
4/15
BC424
User Manual for Blackhawk Riescope
Scope with Adjustable Objective
page 3
Scope with Sniper Edge
page 7
©
2015 BARSKA
®
855 Towne Center Drive | Pomona, CA 91767
(t) 888.666.6769 | (f) 909.445.8169 | www.barska.com
2 3
www.barska.com www.barska.com
Focusing
1. Hold the scope about 2 to 3 inches (6 to 10 cm) away from you eye
and look through the eyepiece until you see the full eld of view.
2. If your reticle isn’t sharp, turn the eyepiece focusing ring in either
direction until the image seen is sharp and focused.
Mounting
1. Make sure you have the appropriate rail for your rie, if not your
rearms dealer will assist you.
2. Place and secure the scope onto the mount ring. Once you have
tted the scope to your desired position, tighten the mount ring
down onto the rail.
Pre-Zeroing
1. Pre-zeroing sighting can be done with scope guide or a shot shaver
which can be obtained from your rearms dealer.
WARNING
BE CERTAIN THAT YOUR FIREARM IS NOT LOADED AND
POINTED AWAY FROM YOU IN A SAFE DIRECTION.
DIRECTLY VIEWING THE SUN OR ANY LIGHT SOURCE
WITH THIS OPTICAL DEVICE CAN CAUSE PERMANENT EYE
DAMAGE.
Use safe gun handling procedures at all times.
ATTENTION: All shooting should be done in an approved range
and in a safe area and that eye and ear protection is used.
DANGER: If you used a bore sighting collimator or another bore
obstructing device, remove it before proceeding. If the barrel has
been drilled for a mount, ensure that the screws do not obstruct
the bore. Do not re live or even blank ammunition with an
obstructed barrel as any obstruction can cause serious damage
to the gun and the possible injury to yourself and other people
around you.
Read all instructions before using scope.
Blackhawk Riescope with Adjustable Objective
Parts of the Scope
* Actual model may vary
A. Eyepiece
B. Zoom Ring
C. Elevation with Lockable Bell
D. Windage with Lockable Bell
E. Rheostat
F. Battery Compartment
G. Adjustable Objective
- For parallax correction
A
E
F
B
C
G
D
4 5
www.barska.com www.barska.com
2. With scope mounted set zoom to mid power and rest the rie on a
steady support.
3. Look through the bore from the breech at a target 50 yards away.
Move to butt stock so that the target is in the center of the bore.
4. Without moving the rie, loosen the lockable bell of the scope at
the base of the turret by turning it counter clockwise with ngers
(see image below).
5. Turn the windage and elevation adjustment dials in the direction you
wish the bullet’s point-of-impact to change (up/down, left/right).
6. Tighten the lockable bell of the scope at the base of the turret by
turning it clockwise.
Boresighting
Bore sighting your riescope with you rie will allow you to quickly and
more accurately “zero in” or “sight in” your riescope to the correct
shooting distance. You will always need to shoot a test group of shots
after you bore sight your ries to you rie. Bore sighting your riescope
will reduce wasting ammunition when targeting in your rie during
test shooting.
Example: You have a newly mounted zoom power riescope on a
rie and aim at a target 100 yards away. You aim for the center of the
target with the scope and re for the rst time, but you see no impact
on the target in the view of the scope. If you were not able to see
where the bullet actually landed then you would need to guess how
you need to adjust the scopes windage and elevation on the next shot.
You would need to continue shooting multiple test shots and adjusting
the scope until the actual impact of the bullet comes into view of the
scope. This will waste time and ammunition.
Why does this happen? A newly mounted riescope’s actual zero
point on a rie is unknown due to many variables; type of scope base,
height of mounting rings, type of rile, type of ammunition etc.
Zeroing
Set scope zoom to the max power, and adjust the windage and
elevation knobs as needed to correct the aim.
After zeroing in your scope, you can follow pre-zeroing procedure to
scale back to zero.
Each click adjustment of the windage and elevation changes/moves
the bullet strikes by the amount in chart below.
1/4”
WINDAGE / ELEVATION (inches per click or movement)
50yds
100yds 200yds 300yds
1/8 inch 1/4 inch 1/2 inch 3/4 inch
NOTE: Climatic conditions such as rain and wind as well as altitude
can affect the trajectory and you might nd it useful note some sight
deviations in the settings from one shooting session to the next.
Re-Zeroing
Re-zeroing scale back to zero is optional and should only be done
after zeroing in your scope.
WARNING: Turning the hex screw too tight or too loose can cause
damage to the scope.
1. Loosen the lockable bell at the base of the turret by turning
it counter-clockwise.
2. Loosen hexagon screw by turning counter clockwise until the screw
hits the stopper screw inside. About 1-1½ turn of the allen wrench.
Note: The hexagon screw CANNOT be totally removed.
3. Pull the turret cap gently up to disconnect it from the drum inside.
4. Turn the cap to reset the scale to zero.
5. Hold the cap and turn hexagon screw clockwise to lock the cap
1-1½ turn of the allen wrench.
6. Your scale is now re-zeroed.
Blackhawk Riescope with Adjustable ObjectiveBlackhawk Riescope with Adjustable Objective
6 7
www.barska.com www.barska.com
Built-in Sniper Edged Sun-Shade
Remove ip up covers to reveal
sunshade. Objective lens is set back in
the housing to allow the sun shade to
cast a shadow and reduce glare.
Focusing
1. Hold the scope about 2 to 3 inches (6 to 10 cm) away from you eye
and look through the eyepiece until you see the full eld of view.
2. If your reticle isn’t sharp, turn the eyepiece focusing ring in either
direction until the image seen is sharp and focused.
Mounting
1. Make sure you have the appropriate rail for your rie, if not your
rearms dealer will assist you.
2. Place and secure the scope onto the mount ring. Once you have
tted the scope to your desired position, tighten the mount ring
down onto the rail.
A
E
F
B
D
C
G
Parts of the Scope
* Actual model may vary
A. Eyepiece
B. Zoom Ring
C. Elevation Adjustment
D. Windage Adjustment
E. Rheostat
F. Battery Compartment
G. Built-in Sniper Edged Sun-Shade
Re-Zeroing Chart
Illuminated Mil-Dot Reticle
The black mil-dot illuminates to red for low light targeting or green for
daylight targeting. The adjustable reticle brightness offers variable
lighting intensities. When replacing batteries use CR2032 with the “+”
side up.
Blackhawk Riescope with Sniper EdgeBlackhawk Riescope with Adjustable Objective
1
4
2
5
3
6
8 9
www.barska.com www.barska.com
Pre-Zeroing
1. Pre-zeroing sighting can be done with scope guide or a shot shaver
which can be obtained from your rearms dealer.
2. With scope mounted set zoom to mid power and rest the rie on a
steady support.
3. Look through the bore from the breech at a target 50 yards away.
Move to butt stock so that the target is in the center of the bore.
4. Without moving the rie, remove the windage and elevation caps by
turning the caps counter clockwise with ngers.
5. Turn the windage and elevation adjustment dials in the direction you
wish the bullet’s point-of-impact to change (up/down, left/right).
6. Replace the windage and elevation caps by turning them clockwise.
Note: If a large amount of windage and elevation adjustments are
needed to bore sight, make half of the scales available adjustments at
a time for the windage and elevation.
Boresighting
Bore sighting your riescope with you rie will allow you to quickly and
more accurately “zero in” or “sight in” your riescope to the correct
shooting distance. You will always need to shoot a test group of shots
after you bore sight your ries to you rie. Bore sighting your riescope
will reduce wasting ammunition when targeting in your rie during
test shooting.
Example: You have a newly mounted zoom power riescope on a
rie and aim at a target 100 yards away. You aim for the center of the
target with the scope and re for the rst time, but you see no impact
on the target in the view of the scope. If you were not able to see
where the bullet actually landed then you would need to guess how
you need to adjust the scopes windage and elevation on the next shot.
You would need to continue shooting multiple test shots and adjusting
the scope until the actual impact of the bullet comes into view of the
scope. This will waste time and ammunition.
Why does this happen? A newly mounted riescope’s actual zero
point on a rie is unknown due to many variables; type of scope base,
height of mounting rings, type of rile, type of ammunition etc.
Zeroing
Set scope zoom to the max power, and observe the bullets strike the
target. Adjust the windage and elevation knobs as needed to correct
the aim. Each click adjustment of the windage and elevation changes/
moves the bullet strikes by the amount in chart below.
1/4”
WINDAGE / ELEVATION (inches per click or movement)
50yds
100yds 200yds 300yds
1/8 inch 1/4 inch 1/2 inch 3/4 inch
NOTE: Climatic conditions such as rain and wind as well as altitude
can affect the trajectory and you might nd it useful note some sight
deviations in the settings from one shooting session to the next.
Illuminated Mil-Dot Reticle
The black mil-dot illuminates to red for low light targeting or green for
daylight targeting. The adjustable reticle brightness offers variable
lighting intensities. When replacing batteries use CR2032 with the “+”
side up.
Blackhawk Riescope with Sniper EdgeBlackhawk Riescope with Sniper Edge
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

Barska AC12449 Instrukcja obsługi

Typ
Instrukcja obsługi
Ten podręcznik jest również odpowiedni dla

w innych językach