Classic Exhibits VK-2922 Setup Instructions
- Typ
- Setup Instructions
www.classicexhibits.com
Step 1
Page 1 of 3
866.652.2100
© 2013
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX -
10’
20’
Plan View
VK-2922 - General Layout
www.classicexhibits.com
Step 2
Page 2 of 3
866.652.2100
© 2013
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - General Information
The Tool Typical Connection
Horizontal Inline Connection (remove only one setscrew)
Base Plate Connection Vertical Connection
(remove only two setscrews)
Most Visionary Designs exhibits can be
assembled with the supplied Hex Key Tool.
Occasionally, a flat head screwdriver may
be required.
Most horizontal extrusion connections have a patented expandable lock. This lock inserts into
the groove of an opposing extrusion. Tightening the lock with the Hex Key Tool expands the lock
and creates a strong positive connection.
Remove only (1) setscrew when disassembling. Replace setscrew in
extrusion after assembling it. Before packing, replace setscrew in
extrusion to avoid losing it.
Attach base plate to round or square
vertical extrusion using the bolt provided.
Be careful not to strip the threads.
When vertical extrusions are packed in
portable cases rather than crates or
tubs, they must broken down into
smaller sections which then require
assembly.
Remove only (2) setscrews when
disassembling. Replace setscrews in
extrusion after assembling it. Before
packing, replace setscrews in extrusion
to avoid losing them.
Using Your Setup Instructions
The Visionary Designs Setup Instructions are created specifically for your
configuration. They are laid out sequentially, including an exploded view of
the entire display, and then a logical series of detailed steps to assemble the
main structure and components. We encourage you to study the instructions
before attempting to assemble your exhibit.
Each page reminds you to tighten the setscrews after disassembling your
exhibit to prevent loss of the locks and setscrews (see below in RED).
This is VERY IMPORTANT.
Cleaning and Packing Your Display
1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only
non-abrasive cleaners.
2) When cleaning laminate inserts or countertops, use mild cleansers and a
soft material such as cotton.
3) Keep all display components away from extreme heat and long exposure
to sunlight to avoid warping and fading.
4) Retain all packing material. It will make re-packing much easier and will
reduce the likelihood of shipping damage.
Typical Connection (cont’d)
Numbered Label
Each extrusion contains a numbered label which
corresponds with setup instructions.
The label is located within a groove of the extrusion
(when possible). With Visionary Designs the labels
contain Black numbers unless otherwise specified.
Detail C E liateDD liateDDetail B
Detail A
Setscrews
www.classicexhibits.com
Step 3
Page 3 of 3
866.652.2100
© 2013
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - Q914 Connections
If the locks are set too far forward, the lock will not
fully engage.
Turn the set screw clockwise to move the lock
back into the extrusion, counter-clockwise
to move the lock outward.
The lock should be set back about 1 mm
(1/16”) from the edge of the extrusion for
the locks to engage properly.
When the lock is properly engaged, the
extrusions will fit tightly together.
When the lock is properly engaged, the
extrusion will not move.
Turn the hex wrench clockwise to open the
lock and secure in the groove.
1
2
3If the locks are not properly engaged, gaps
will be noticable and the extrusion will be
loose.
www.classicexhibits.com
Step 4
Page 4 of 3
866.652.2100
© 2013
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - SEG Graphic Installation
Graphic Removal
Graphic: To Ensure Proper Fit
Corner A
Corner D
Corner B
Corner C
It is important to first insert graphic
into each alternater corner then to
the sides of the frame.
If this is not done, graphic will not fit
into the frame correctly.
Step 1
Insert corner A.
Turn edge of graphic so silicon welt
is perpendicular to face of graphic.
Insert narrow side of welt with fabric
to outside into the channel.
Repeat for other side of this corner.
Step 2
Repeat Step 1 for opposite corner
C, then insert corner B, followed by
corner corner D, to complete the
installation of the corners.
Step 3
Once all corners are inserted, press
one silicon edge into channel from
corners and work toward the center.
Make sure welt is fully inserted into
channel. Continue until all sides are
done. Smooth out edges of graphic.
To remove the graphic from
the frame, locate the fabric
pull tab.
Gently pull up on the tab to
remove the fabric.
SEG Graphic Installation
www.classicexhibits.com
Step 1
Page 1 of 3
866.652.2100
© 2013
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - Room Assembly
Item Qty. Description
1 1 96” Q914 Vertical Extrusion
2 1 96” Q914 Vertical Extrusion
3 1 96” Q914 Vertical Extrusion
4 1 96” Q914 Vertical Extrusion w/Door Stop
5 1 96” Q914 Vertical Extrusion w/Door Hinges
6a/6b 1/1 26” Q914 Horizontal Extrusion
7a/7b 1/1 64“ Q914 Horizontal Extrusion
8a/8b 1/1 37” Z45 Horizontal Extrusion
9a/9b 1/1 64” Z45 Horizontal Extrusion
10a/10b 1/1 37” Z45 Horizontal Extrusion
1
2
3
4
5
6a
6b
7a
7b
8b
8a
9a
9b
10b
Infill
Assembled
Door
10a
Top view of
vertical
Velcro
3
Steps:
1) Slide Door Threshold into bottom of verticals [4,5] as
shown in detail.
2) Connect horizontals [6a,6b] between verticals [1 & 2].
3) Connect horizontals [8a,8b] between verticals [2 & 3].
4) Connect horizontals [9a,9b] between verticals [3,4].
5) Connect horizontals [7a,7b] between verticals [2 & 5].
6) Connect horizontals [10a,10b] between verticals [4 & 5],
inserting infill as shown.
6) Hang assembled door to vertical [5] as shown in detail.
7) Attach graphics to SEG grooves as shown
on general information page.
8) Attach backer fabric to front of backwall
as shown.
Door Attachment
Pin
Slide pin into
hinge attached
to vertical.
Slide door
hinge atop pin.
Door
Hinge
Hinge
Door Threshold
Tighten
to secure
Slide into
groove
Top view of
vertical
2
www.classicexhibits.com
Step 2
Page 2 of 3
866.652.2100
© 2013
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX -
Backwall Assembly
Steps:
1) Connect horizontals [13a,13b] between verticals [4,11].
2) Connect horizontals [14a,14b] between verticals [11,12].
3) Attach boomerang foot to outside of vertical [12] as shown.
4) Attach graphics to SEG groove on assembled backwall as
shown in general information pages.
4
11
12
14a
14b
13a
13b
Item Qty. Description
11 1 96” Q914 Vertical Extrusion
12 1 96” Q914 Vertical Extrusion
13a/13b 1 64” Z45 Horizontal Extrusion
14a/14b 1 64” Z45 Horizontal Extrusion
SEG Groove faces front
www.classicexhibits.com
Step 3
Page 3 of 3
866.652.2100
© 2013
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - Ceiling Assembly
Item Qty. Description
15 1 87.63” Z41 Horizontal Extrusion
16 1 14.5” S40 Horizontal Extrusion
17 1 21.75” Z41 Horizontal Extrusion
18 1 21.75” Z140 Horizontal Extrusion
19 1 21.75” Z140 Horizontal Extrusion
20 1 21.75” Z41 Horizontal Extrusions
21 4 18.256” Z41 Horizontal Extrusions
Steps:
1) Attach horizontals together inserting infills as shown.
2) Attach assembled ceiling to top of sorage room extrusions
using bolts as shown.
15
16
17
18
19
20
21
21
21
21
Infill Infill Infill
Infill
Puck Light
Puck Light
Ceiling Attachment
Attach horizontal extrusions to top of
storage room extrusions with bolts as shown.
www.classicexhibits.com
Step 4
Page 4 of 3
866.652.2100
© 2013
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX -
Attachments
Steps:
1) Attach lights to top of backwall as shown.
2) Attach monitor mount and monitor mount plate
between verticals [1,2] as shown in detail.
3) Attach iPad clamshells to backwall as shown.
4) Attach literature racks to backwall as shown.
*
*
*
*
*
*
*
*
*
Monitor Mount Attachment
Attach mounting plate
to verticals as shown.
Then attach
wall plate to plate
using bolts and wing nuts
Tighten Lock
to Secure
Swivel
Mounting
Plate
iPad Mount Attachment
*
Hex
Nuts
Swivel
Mounting Plate
Bolt iPad clamshell to
mounting plate with hex nuts.
Attach connector piece to iPad
mount as shown. Then connect
assembled iPad mount to vertical
extrusion.
Attach connector piece to rack
as shown. Then connect
assembled literature
rack to vertical extrusion.
Literature Rack Attachment
Tighten Lock
to Secure
www.classicexhibits.com
866.652.2100
© 2013
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - Crate Packing
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
Classic Exhibits VK-2922 Setup Instructions
- Typ
- Setup Instructions
w innych językach
- English: Classic Exhibits VK-2922
Powiązane dokumenty
-
Classic Exhibits VK-1122 Setup Instructions
-
-
-
-
-
-
-
-
-