Parkside PABS 18-LI B2 Operation and Safety Notes

IAN 75636

CORDLESS DRILL PABS 18-Li B2

AKKU-BOHRSCHRAUBER

Bedienungs- und Sicherheitshinweise

Originalbetriebsanleitung

CORDLESS DRILL

Operation and Safety Notes

Translation of original operation manual

WIERTARKO-WKRĘTARKA

AKUMULATOROWA

Wskazówki dotyczące obsługi i bezpieczeństwa

Tłumaczenie oryginalnej instrukcji obsługi

AKUMOLATORSKI VRTALNI VIJAČNIK

Navodila za upravljanje in varnostna opozorila

Prevod originalnega navodila za uporabo

AKU VRTACÍ ŠROUBOVÁK

Pokyny pro obsluhu a bezpečnostní pokyny

Překlad originálního provozního návodu

AKU VŔTACÍ SKRUTKOVAČ

Pokyny pre obsluhu a bezpečnostné pokyny

Preklad originálneho návodu na obsluhu

GB Operation and Safety Notes Page 5

PL Wskazówki dotyczące obsługi i bezpieczeństwa Strona 17

SI Navodila za upravljanje in varnostna opozorila Stran 29

CZ Pokyny pro obsluhu a bezpečnostní pokyny Strana 41

SK Pokyny pre obsluhu a bezpečnostné pokyny Strana 51

DE / AT / CH Bedienungs- und Sicherheitshinweise Seite 61

Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of the

device.

Przed przeczytaniem proszę rozłożyć stronę z ilustracjami, a następnie proszę zapoznać się z wszystkimi

funkcjami urządzenia.

Pred branjem odprite stran s slikami in se nato seznanite z vsemi funkcijami naprave.

Před čtením si otevřete stranu s obrázky a potom se seznamte se všemi funkcemi přístroje.

Pred čítaním si odklopte stranu s obrázkami a potom sa oboznámte so všetkými funkciami prístroja.

Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen

Funktionen des Gerätes vertraut.

A B

12

5

C

1

2

3

1413

6

7

11

10

9

8

15

6

1617

7

4

5 GB

Table of contents

Introduction

Intended purpose ................................................................................................................................ Page 6

Equipment Components ......................................................................................................................Page 6

Scope of delivery ................................................................................................................................Page 7

Technical Data ....................................................................................................................................Page 7

General safety advice for electrical power tools

1. Workplace safety ...........................................................................................................................Page 8

2. Electrical safety ............................................................................................................................... Page 8

3. Personal safety ................................................................................................................................Page 8

4. Careful handling and use of electrical power tools .....................................................................Page 9

5. Use and handling of the cordless electrical power tool ..............................................................Page 9

6. Service .............................................................................................................................................Page 10

Safety advice relating to cordless drill drivers ..................................................................................Page 10

Attention - Service lines! ......................................................................................................................Page 10

Original ancillaries / accessories .......................................................................................................Page 10

Before first use

Charging the battery pack .................................................................................................................Page 10

Insertion / removal of a battery pack into the appliance ..................................................................Page 11

Checking battery status ......................................................................................................................Page 11

Changing tools .................................................................................................................................... Page 11

Torque pre-selection ............................................................................................................................Page 11

2 Gear Drive .......................................................................................................................................Page 12

Preparing the tool for use

Switching On / Off .............................................................................................................................. Page 12

Switching the LED light on and off .....................................................................................................Page 12

Adjusting the speed ............................................................................................................................Page 12

Switching direction of rotation ...........................................................................................................Page 12

Tips and Tricks ..................................................................................................................................... Page 12

Cleaning and Maintenance ..............................................................................................Page 13

Service ...............................................................................................................................................Page 13

Warranty ......................................................................................................................................... Page 13

Disposal ............................................................................................................................................Page 14

Conformity Declaration / Manufacturer ................................................................Page 15

6 GB

Introduction Introduction / General safety advice for electrical power tools

Cordless drill PABS 18-Li B2

Q

Introduction

We congratulate you on the purchase of

your new device. You have chosen a

high

quality product. The instructions for use

are part of the product. They contain important in-

formation concerning safety, use and disposal. Be-

fore using the product, please familiarise yourself

with all of the safety information and instructions

for use. Only use the unit as described and for the

speciﬁed applications. If you pass the product on

to anyone else, please ensure that you also pass

on all the documentation with it.

Q

Intended purpose

This appliance is designed for drilling and screwing

into wood, plastic and metal. Use the appliance only

as described and only for the purposes indicated.

Any other uses, and modiﬁcations to the appliance,

are deemed to be improper usage and may result

in serious physical injury. The manufacturer accepts

no responsibility for damage(s) resulting from

improper usage. The appliance is not intended for

commercial use.

Q

Equipment Components

1

Gear selector switch

2

Direction of rotation switch / lock

3

ON / OFF Switch / R.P.M. regulator

4

Bit holder

5

Belt clip

The following pictograms are used in these operating instructions / on the device:

Read instruction manual! Safety class II

Observe caution and safety notes! Drill chuck, Made In Germany

Caution – electric shock!

Danger to life!

Spindle lock

Explosive material! Drill setting (torque preselect)

W

Watts (Eﬀective power) Wear ear protection.

n

0

Design no-load speed

Keep children away from electrical

power tools!

V

~

Voltage For indoor use only!

Ah

Amp (Battery capacity)

Check that the device, mains lead

and plug are in good condition!

Nm

Newton metre (torque)

Dispose packaging and appliance in

an environmentally-friendly way!

DC (current and voltage type)

Do not dispose of rechargeable

batteries with your household refuse!

7 GB

Introduction

6

Rechargeable battery pack

7

Battery pack release button

8

LED light button

9

LED light

10

Rechargeable battery display LED

11

Rechargeable battery charge state button

12

LED working light

13

Drill chuck

14

Torque pre-selector

15

Fast charger

16

Red charge-control LED

17

Green charge-control LED

Q

Scope of delivery

1 Cordless drill with rechargeable battery pack

1 Bit PH2 50 mm

1 Fast charger

1 Carry case

1 Directions for use

Q

Technical Data

PABS 18-Li B2 Cordless drill:

Nominal voltage: 18 V

Idle-running speed: 1st gear: max. 400 min

-1

Idle-running speed: 2nd gear: max. 1400 min

-1

Drill chuck

clamping range: max. 10 mm

Maximum

drill diameter: Steel: 10 mm,

Wood: 30 mm

Max. torque: 35 Nm

PABS 18-Li B2-1 Battery Pack:

Type: LITHIUM-ION

Nominal voltage: 18 V

Capacity: 1.5 Ah

Energy content: 27 Wh

PABS 18-Li B2-2 Fast Charger:

INPUT

Nominal voltage: 230 V∼, 50 Hz

Power input: 55 W

OUTPUT

Nominal voltage: 18 V

Charging current 2 A

Charging time: approx. 60 min

Protection class: II /

Noise and vibration data:

Measured values for noise are determined in accor-

dance with EN 60745. The A-weighted noise level

of the electrical power tool are typically:

Sound pressure level: 76 dB(A)

Sound power level: 87 dB(A)

Uncertainty K: 3 dB

Total vibration (vector sum of three directions) is

calculated in accordance with EN 60745:

Screwing: Vibration emission value

a

h,D

= 0.865 m / s

2

,

uncertainty K = 1.5 m / s

2

,

Drilling: Vibration emission value

a

h

= 2.546 m / s

2

,

uncertainty K = 1.5 m / s

2

.

The vibration level speciﬁed in

these instructions was measured in accordance with

an EN 60745 standardised measurement process

and can be used to compare equipment. The vibra-

tion emission value speciﬁed can also serve as a

preliminary assessment of the exposure.

The vibration level will change according to the ap-

plication of the electrical tool an in some cases may

exceed the value speciﬁed in these instructions. Re-

gularly using the electric tool in such a way may

make it easy to underestimate the vibration.

Note: If you wish to make an accurate assessment

of the vibration loads experienced during a particular

period of working, you should also take into account

the intervening periods of time when the device is

switched oﬀ or is running but is not actually in use.

This can result in a much lower vibration load over

the whole of the period of working.

Introduction / General safety advice for electrical power tools

8 GB

General safety advice for electrical power toolsGeneral safety advice for electrical power tools

General safety advice for

electrical power tools

Read all the safety advice

and instructions! Failure to observe the safety

advice and instructions may result in electric shock,

ﬁre and / or serious injury.

Keep all the safety advice and instructions

in a safe place for future reference!

The term “electrical tool” used in the safety advice

refers to electrical tools powered by mains electrici-

ty (by means of a mains lead) and electrical tools

powered by rechargeable batteries (without a

mains lead).

1.

Workplace safety

a) Keep your working area clean and

well lit. Untidy or poorly lit working areas

can lead to accidents.

b)

Do not work with the device

in potentially explosive envi-

ronments in which there are

inflammable liquids, gases or dusts.

Electrical power tools create sparks, which can

ignite dusts or fumes.

c)

Keep children and other

people away while you are

operating the electrical tool.

Distractions can cause you to lose control of

the device.

2.

Electrical safety

a)

The mains plug on the device must match

the mains socket. The plug must not

be modified in any way. Do not use

an adapter plug with devices fitted

with a protective earth. Unmodiﬁed

plugs and matching sockets reduce the risk of

electric shock.

b) Avoid touching earthed surfaces such

as pipes, radiators, ovens and refrig-

erators with any part of your body.

There is an increased risk of electric shock if

your body is earthed

.

c) Keep the device away from rain or

moisture. Water entering an electrical device

increases the risk of electric shock.

d)

Do not use the mains lead for

any purpose for which it was

not intended, e.g. to carry the

device, to hang up the device or to pull

the mains plug out of the mains socket.

Keep the mains lead away from heat,

oil, sharp edges or moving parts of the

device. Damaged or tangled mains leads

increase the risk of electric shock.

e) When working outdoors with an

electrical power tool always use ex-

tension cables that are also approved

for use outdoors. The use of an extension

cable suitable for outdoor use reduces the risk

of electric shock.

f) Use a residual current device (RCD)

for protection if operating the electri-

cal power tool in a moist environment

is unavoidable. The use of an RCD reduces

the risk of electric shock.

3. Personal safety

a) Remain alert at all times, watch what

you are doing and always proceed

with caution. Do not use the device if

you are tired or under the influence of

drugs, alcohol or medication. One mo

ment

of carelessness when using the device can lead

to serious injury.

b) Wear personal protective equipment

and always wear safety glasses. The

wearing of personal protective equipment such

as dust masks, non-slip safety shoes, safety

helmets or ear protectors, appropriate to the

type of electrical power tool used and work

undertaken, reduces the risk of injury.

c) Avoid unintentional operation of the

device. Check that the electrical power

tool is switched off before you connect

it to the mains, pick it up or carry it.

Accidents can happen if you carry the device

9 GB

General safety advice for electrical power toolsGeneral safety advice for electrical power tools

with your ﬁnger on the ON / OFF switch or with

the device switched on.

d) Remove any setting tools or spanners

before you switch the device on. A tool

or spanner left attached to a rotating part of a

device can lead to injury.

e) Avoid placing your body in an unnat-

ural position. Keep proper footing

and balance at all times. By doing this

you will be in a better position to control the

device in unforeseen circumstances.

f) Wear suitable clothing. Do not wear

loose clothing or jewellery. Keep your

hair, clothing and gloves clear of mov-

ing parts. Loose clothing, jewellery or long

hair can become trapped in moving parts.

g) If vacuum dust extraction and collection

devices are fitted do not forget to

check

that they are properly connected and

correctly used. The use of these devices

reduces the hazard presented by dust.

4.

Careful handling and use

of electrical power tools

a) Do not overload the device. Always

use an electrical power tool that is

intended for the task you are under-

taking. By using the right electrical power

tool for the job you will work more safely and

achieve a better result.

b) Do not use an electrical power tool if

its switch is defective. An electrical power

tool that can no longer be switched on and oﬀ

is dangerous and must be repaired.

c) Pull the mains plug out of the socket

and / or remove the rechargeable bat-

tery before you make any adjustments

to the device, change accessories or

when the device is put away. This pre-

caution is intended to prevent the device from

unintentionally starting.

d) When not in use always ensure that

electrical power tools are kept out of

reach of children. Do not let anyone use

the device if he or she is not familiar

with it or has not read the instructions

and advice. Electrical power tools are dan-

gerous when they are used by inexperienced

people.

e) Look after the device carefully. Check

that moving parts are working prop-

erly and move freely. Check for any

parts that are broken or damaged

enough to detrimentally affect the

functioning of the device. Have dam-

aged parts repaired before you use

the device. Many accidents have their origins

in poorly maintained electrical power tools.

f) Keep cutting tools clean and sharp.

Carefully maintained cutting tools with sharp

cutting edges are less likely to jam and are

easier to control.

g) Use the electrical power tool, accesso-

ries, inserted tools etc. in accordance

with these instructions and advice, and

the stipulations drawn up for this par-

ticular type of device. In doing this, take

into account the working conditions

and the task in hand. The use of electrical

power tools for purposes other than those in-

tended can lead to dangerous situations.

5. Use and handling of the cord-

less electrical power tool

a) Charge a rechargeable battery unit

using only the charger recommended

by the manufacturer. Chargers are often

designed for a particular type of rechargeable

battery unit. There is the danger of ﬁre if other

types of rechargeable battery units are used.

b)

Only the rechargeable battery units su

p-

plied are to be used with an electrical

power tool. The use of other rechargeable bat-

t

ery units may lead to the danger of injury or ﬁre.

c) When they are not being used, store

rechargeable battery units away from

paperclips, coins, keys. nails, screws

or other small metal objects that could

cause the contacts to be bridged. Short-

circuiting the contacts of a rechargeable battery

unit may result in heat damage or ﬁre.

10 GB

Before first use General safety advice for electrical power tools / Before first use

d)

Fluids may leak out of rechargeable

battery units if they are misused. If

this happens, avoid contact with the

ﬂuid. If contact occurs, ﬂush the aﬀect-

ed area with water. Seek additional

medical help if any of the ﬂuid gets

into your eyes. Escaping battery ﬂuid may

cause skin irritation or burns.

CAUTION! DANGER OF EX-

PLOSION! The batteries must

never be recharged!

6. Service

a) Have your device repaired at the ser-

vice centre or by qualified specialist

personnel using original manufacturer

parts only. This will ensure that your device

remains safe to use.

Safety advice relating

to cordless drill drivers

Hold the device by the

insulated handle surfaces when you

are undertaking work where there is

the danger of the screw striking hidden

electricity cables or the device’s mains

lead. Contact of the screw with a live wire could

cause metal parts of the device to become live

and lead to electric shock.

Children or persons who lack the knowledge or

experience to use the device or whose physical,

sensory or intellectual capacities are limited

must never be allowed to use the device without

supervision or instruction by a person responsi-

ble for their safety. Children must never be

allowed to play with the device.

Securely support the workpiece. A workpiece

held in a clamp or vice is kept more securely in

place than one held by your hand.

POISONOUS DUSTS!

Harmful / noxious dusts generated from your

work represent a risk to the health of the person

operating the device and to anyone near the

work area. Wear safety glasses and a dust mask!

Do not drill any material containing

asbestos. Asbestos is a known carcinogen.

Hold the electrical power tool ﬁrmly.

High reaction torques may occur momentarily

during tightening or loosening of screws.

If the inserted tool jams, switch oﬀ the

electrical power tool immediately. Be

prepared for high reaction torques as they may

cause kickback. The inserted tool may jam if

the electrical power tool is overloaded or is

held at an angle to the workpiece.

Before you carry out any tasks on the

device, transport or store it, make sure

that the direction of rotation switch is

in the middle position (lock). To prevent

the device from starting up unintentionally.

Q

Attention - Service lines!

DANGER! Take steps to ensure that

you do not hit upon any service lines

(electricity, gas, water) when work-

ing with electrical appliances. Check, if

need be with a service line detector, before

you start to cut or bore into a surface.

Q

Original ancillaries /

accessories

Use only the ancillaries and accessories

that are detailed in the operating

instructions. The use of ancillaries and ac-

cessories other than those recommended in the

operating instructions could lead to an increased

risk of personal injury for you.

Q

Before ﬁrst use

Q

Charging the battery pack

DANGER OF ELECTRIC

SHOCK! Before cleaning or servicing the

charging station or the battery pack always

ensure that the plug is not in the mains socket.

11 GB

Before first use General safety advice for electrical power tools / Before first use

Note! A new battery pack, or one that has not

been in use for an extended period, must be charged

up before the ﬁrst / renewed usage.

The battery pack attains its full capacity after ca.

3–5 charging cycles.

CAUTION! Always ensure the plug is removed

from the mains socket before inserting a battery pack

into, or removing one from, the charging station.

Never charge the battery pack if the ambient

temperature is less than 10 °C or greater than

40 °C.

1. Insert the battery pack

6

into the quick-

charger

15

(see Fig. C).

2. Insert the mains plug into the mains socket. The

ﬂashing green charge indicator LED

17

shows

that charging is in progress.

3. The charging process is completed when the

green charge indicator LED

17

light up and the

accumulator pack

6

is ready for operation.

4. If the red charge indicator LED

16

lights up, the

quick battery charger

15

is in standby mode;

the accumulator pack

6

is not connected.

5. If the red charge indicator LED

16

starts ﬂas-

hing, this means that the accumulator pack

6

has become too hot; no charging process.

Never charge the battery pack for a second time

immediately after a fast charging process has

been completed. This can give rise to the battery

pack becoming overcharged and to a reduced

service life of the battery and charging station.

Switch the charger oﬀ for at least 15 minutes

between two successive charging procedures.

Remove the power plug from the wall socket.

Q

Insertion / removal of a battery

pack into the appliance

Ensure that the appliance is switched oﬀ before in-

serting the battery. The insertion of a battery into an

electrical appliance that is switched on can lead to

accidents.

Inserting the rechargeable battery pack:

Move the rotation switch

2

into the middle

position (lock) and push the rechargeable bat-

tery pack

6

into the handle until it engages.

Removing the rechargeable battery pack:

Press the release button

7

and remove the

rechargeable battery pack

Q

Checking battery status

To check the battery status, press the battery

LED button

11

(refer to main diagram). The

status or residual capacity will be indicated in

the battery LED

10

as follows:

GREEN / RED / ORANGE = maximum charge /

capacity

RED / ORANGE = medium charge / capacity

RED = weak charge – recharge battery

Q

Changing tools

Your cordless electric drill / screwdriver has a fully

automatic spindle lock

and is ﬁtted with an

enclosed keyless chuck incorporating the latest

technology from

”Made in Germany”.

Once the motor has come to a halt, the drive shaft

is automatically locked, so that the chuck

13

can

be opened simply by turning it

.

After you have inserted the required bit and ﬁxed it

in place by turning the chuck

, you can immedi-

ately continue working. The spindle lock releases

itself automatically when the motor is started (by

operation of the ON / OFF switch

3

).

Q

Torque pre-selection

You can adjust the torque by using

14

torque pre-

selection. The torque levels regulate a range of up

to ca. 35 Nm.

Select a low setting for small screws, soft work

material.

12 GB

Before first use / Preparing the tool for use

Select a high setting for large screws, hard

work materials and for the extraction of screws.

For drilling, push the selector to the setting for

drilling, in that you adjust the torque pre-selector

to the position

.

For drilling tasks, also push the gear selector

switch

1

to the front (Position: 2).

Q

2 Gear Drive

CAUTION! Move the gear selector switch

1

only after the device has come to a standstill.

Failure to observe this advice may result in damage

to the device.

In the ﬁrst gear (Gear selector switch

1

in Position: 1)

A speed of up to approx. 400 rpm can be achieved

and a high torque. This setting is intended for use w

ith

all screwing tasks and for accessories (see example

Fig. B).

In the second gear (Gear selector switch

1

in Position: 2)

It achieves a speed of up to approx. 1400 rpm, for

the carrying out of drilling tasks (see example Fig. A).

Q

Preparing the tool for use

Q

Switching ON /OFF

Switching on:

To start the appliance squeeze on the ON /

OFF switch

3

and then keep it pressed down.

The LED working light

12

comes on with a slightly

or fully pressed ON /OFF switch

3

and illumi-

nates the working area in poor lighting conditio

ns.

Switching off:

To stop the appliance, release the ON / OFF

switch

3

.

Switching the LED light on and oﬀ

Switching on:

Press the LED light button

8

to switch on the

LED light

9

.

Switching off:

Press the LED light button

8

again to switch

oﬀ the LED light

9

.

Q

Adjusting the speed

The ON / OFF switch

3

has a variable speed con-

trol device. Slight pressure on the ON / OFF switch

3

will cause the rotation speed to slow down. With

increased pressure, the rotational speed will increase.

Note: The integrated engine brake means that the

device will come to a fast standstill.

Q

Switching direction of rotation

To switch the direction of rotation, push the

direction of rotation switch

2

to either the

right or to the left.

Q

Tips and Tricks

Before you use the appliance, check to see

that the screw or drill bit is properly ﬁtted, i.e.

located centrally in the chuck.

Screw bits are designated with their dimensions

and their shape. If you are unsure, always try

the particular screw bit out to see whether it sits

in the screw head without any free play.

Torque:

Smaller screws and bits in particular can be

easily damaged if you adjust the appliance

with too high a torque and/or rotation speed.

Hard screwdriving conditions (into metal):

Particularly high torques can occur, for example

with metal screws tightened by socket tool bits.

Select a lower rotation speed.

Preparing the tool for use / Cleaning and Maintenance / Service / Warranty

13 GB

Before first use / Preparing the tool for use

Soft screwdriving conditions (e.g. into

soft wood):

You should also select a low speed in order not to

damage the wood workpiece surface through con-

tact with the metal screw head. Use a countersinker.

When drilling into wood, metal and other

materials, take note of the following advice:

With small diameter drill bits use a high drill

speed. For large diameter drill bits, use a low

drill speed.

For hard materials, select a low drill speed.

For soft materials, select a high drill speed.

Secure or ﬁx down the workpiece (if possible)

in a clamp or vice.

Mark the intended position of the hole with a

centre punch or a nail and select a low drill speed

for drilling.

Take the rotating drill bit out of the hole frequently

so that swarf or drill dust can be re-moved and

the hole and tool is ventilated.

Drilling in metal:

Use a metal drill bit (HSS). For the best results,

you should cool the bit with oil. Metal drill bits

can also be used to drill into plastic.

Drilling in stone:

Use a circular shafted masonry drill bit with a

hardened metal tip.

Drilling in wood:

Normally you should use a wood drill with a

centring point. For deep holes, use an auger type

bit. For large diameter holes, use a forstner bit.

You can screw small screws into soft wood

without the need for pre-drilling.

Q

Cleaning and Maintenance

CAUTION! Place the direction of rotation

switch

2

into the middle position before carry-

ing out any tasks on the device, e.g. changing

tools or maintenance, or before transporting or

storing the device. Inadvertent operation of the

ON / OFF switch

3

may result in injury.

Pull the mains lead out of the mains socket eve-

ry time and remove the battery before you clean

or maintain the device.

The Cordless drill is maintenance-free.

Always keep the device clean, dry and free of

oil or grease.

Clean the device immediately after you have

ﬁnished using it.

Do not allow any liquids to enter the device.

Use a cloth to clean the housing. Never use

petrol, solvents or cleaning agents that might

attack plastic.

Q

Service

Have your device repaired

at the service centre or by qualified

specialist personnel using original

manufacturer parts only. This will ensure

that your device remains safe to use.

If the plug or lead needs

to be replaced, always have the

replacement carried out by the manu-

facturer or its service centre. This will

ensure that your device remains safe to use.

Q

Warranty

The warranty for this appliance is for 3

years from the date of purchase. The ap-

pliance has been manufactured with care

and meticulously examined before deliv-

ery. Please retain your receipt as proof

of purchase. In the event of a warranty

claim, please make contact by telephone

with our Service Department. Only in this

way can a post-free despatch for your

goods be assured.

The warranty covers only claims for material and

maufacturing defects, but not for transport damage,

for wearing parts or for damage to fragile compo-

nents, e.g. buttons or batteries. This product is for pri-

vate use only and is not intended for commercial use.

Preparing the tool for use / Cleaning and Maintenance / Service / Warranty

14 GB

Conformity Declaration / Manufacturer

The warranty is void in the case of abusive and im-

proper handling, use of force and internal tamper-

ing not carried out by our authorized service branch.

Your statutory rights are not restricted in any way

by this warranty.

The warranty period will not be extended by repairs

made unter warranty. This applies also to replaced

and repaired parts. Any damage and defects extant

on purchase must be reported immediately after

unpacking the appliance, at the latest, two days after

the purchase date. Repairs made after the expiration

of the warranty period are subject to payment.

GB

Service Great Britain

Tel.: 0871 5000 720

(0,10 GBP/Min.)

e-mail: kom[email protected]

IAN 75636

Q

Disposal

The packaging comprises exclusively en-

vironmentally-friendly material. Dispose

of it in your local recycling containers.

Do not dispose of electrical

appliances with your domestic

waste!

According to the European Directive 2002 / 96 / EC,

concerning used electrical and electronic appliances

and its implementation in national law, superannu-

ated electrical appliances must be collected and

disposed of via an environmentally suitable recy-

cling facility.

Do not dispose of rechargeable

batteries with your household

refuse!

Defective or worn out rechargeable batteries must

be recycled according to Directive 2006 / 66 / EC.

Dispose of batteries and appliances over the existing

collection facilities.

Your local communal or municipal authorities can

provide information on how to dispose of the worn

out appliance.

Warranty / Disposal

15 GB

Conformity Declaration / Manufacturer

Q

Conformity Declaration /

Manufacturer

We, Kompernaß GmbH, the person responsible for

documents: Mr Semi Uguzlu, Burgstr. 21, D-44867

Bochum, Germany, hereby declare that this product

complies with the following standards, normative

documents and EU directives:

Machinery Directive

(2006 / 42 / EC)

EC Low Voltage Directive

(2006 / 95 / EC)

Electromagnetic compatibility

(2004 / 108 / EC)

Applicable harmonized standards

EN 60745-1:2009+A11

EN 60745-2-1:2010, EN 60745-2-2:2010

EN 55014-1:2006+A1+A2

EN 55014-2:1997+A1+A2

EN 61000-3-2:2006+A1+A2

EN 61000-3-3:2008

EN 60335-1:2002+A1+A11+A12+A2+A13+A14

EN 60335-2-29:2004

EN 62233:2008

Type / Appliance Designation:

Cordless drill PABS 18-Li B2

Date of manufacture (DOM): 07–2012

Serial number: IAN 75636

Bochum, 31.07.2012

Semi Uguzlu

- Quality Manager -

We reserve the right to make technical modiﬁcations

in the course of further development.

Warranty / Disposal

16

Spis zawartości

17 PL

Spis zawartości

Wstęp

Przeznaczenie ..................................................................................................................................Strona 18

Wyposażenie ...................................................................................................................................Strona 19

Zakres dostawy ................................................................................................................................Strona 19

Dane techniczne ..............................................................................................................................Strona 19

Ogólne wskazówki bezpieczeństwa dla elektronarzędzi

1. Bezpieczeństwo miejsca pracy ..................................................................................................Strona 20

2. Bezpieczeństwo elektryczne .......................................................................................................Strona 20

3. Bezpieczeństwo osób .................................................................................................................Strona 21

4. Staranne obchodzenie się i użytkowanie narzędzi elektrycznych ..........................................Strona 21

5. Używanie i obchodzenie się z narzędziem akumulatorowym .................................................Strona 22

6. Serwis ...........................................................................................................................................Strona 22

Wskazówki dotyczące bezpieczeństwa dla wiertarkowkrętarek akumulatorowych .................Strona 22

Uwaga na przewody! ..................................................................................................................... Strona 23

Oryginalne akcesoria / dodatkowy sprzęt .....................................................................................Strona 23

Przed uruchomieniem

Ładowanie akumulatora ..................................................................................................................Strona 23

Zakładanie / zdejmowanie akumulatora z urządzenia ................................................................Strona 24

Kontrala stanu akumulatora ............................................................................................................ Strona 24

Zmiana narzędzi ..............................................................................................................................Strona 24

Nastawienie momentu obrotowego ............................................................................................... Strona 24

Przekładania 2-biegowa .................................................................................................................Strona 24

Uruchomienie

Włączenie / Wyłączenie .................................................................................................................Strona 25

Włączanie / wyłączanie lampki LED .............................................................................................. Strona 25

Ustawienie prędkości .......................................................................................................................Strona 25

Zmiana kierunku obrotów ...............................................................................................................Strona 25

Wskazówki i porady .......................................................................................................................Strona 25

Konserwacja i czyszczenie............................................................................................Strona 26

Serwis .............................................................................................................................................Strona 26

Gwarancja ..................................................................................................................................Strona 26

Usuwanie ..................................................................................................................................... Strona 27

Deklaracja zgodności / Producent ..........................................................................Strona 27

18 PL

Wstęp

Wiertarko-wkrętarka

Akumulatorowa PABS 18-Li B2

Q

Wstęp

Gratulujemy zakupu nowego urządzenia.

Tym samym zdecydowali się Państwo na

zakup produktu wysokiej jakości. Instrukcja

obsługi jest częścią tego produktu. Zawiera ona

ważne wskazówki dotyczące bezpieczeństwa,

użytkowania iutylizacji. Przed pierwszym użyciem

produktu należy zapoznać się ze wszystkimi wska-

zówkami dotyczącymi obsługi ibezpieczeństwa.

Używać produktu wyłącznie zgodnie zjego poniżej

opisanym przeznaczeniem. Wprzypadku przeka-

zania produktu innej osobie należy dołączyć do

niego całą jego dokumentację.

Q

Przeznaczenie

To urządzenie jest przeznaczone do wiercenia i

wkręcania w drewno, plastik i metal. Urządzenie

należy stosować zgodnie z opisem i w podanych

zakresach użytkowania. Jakiekolwiek inne użycie

lub zmiany urządzenia uważane są za niezgodne

z przeznaczeniem i kryją w sobie poważne nie-

bezpieczeństwo wypadku. Producent nie bierze

na siebie żadnej odpowiedzialności w przypadku

powstania szkody, wynikającej z użytkowania

urządzenia w sposób całkowicie niezgodny z

W niniejszej instrukcji obsługi urządzenia zastosowano następujące piktogramy:

Przeczytaj instrukcję obsługi! Klasa bezpieczeństwa II

Przestrzegaj wskazówek

ostrzegawczych i bezpieczeństwa!

Uchwyt wiertarski ‘Made in

Germany’

Ostrzeżenie przed porażeniem

prądem elektrycznym! Zagrożenie

dla życia!

Blokada wrzeciona

Niebezpieczeństwo wybuchu!

Stopień wiertarski

(dobór momentu obrotowego)

W

Watt (Moc skuteczna) Nosić ochronniki słuchu.

n

0

Wymiarowa liczba obrotów

biegu luzem

Dzieci trzymać z daleka od

narzędzia elektrycznego!

V

~

Volt (Napięcie przemienne)

Tylko do użytku w pomieszczeniach

wewnętrznych!

Ah

ampero (Pojemność akumulatora)

Zwracać uwagę na nienaruszony

stan urządzenia, kabla sieciowego

oraz wtyczki sieciowej!

Nm

Niutonometr (moment obrotowy)

Opakowanie i urządzenie przekaż

do utylizacji zgodnie z przepisami o

ochronie środowiska!

Prąd stały (rodzaj prądu i napięcia)

Nie wyrzucać akumulatorów do

odpadów i śmieci z gospodarstw

domowych.

Wstęp

19 PL

Wstęp Wstęp

przeznaczeniem. Urządzenie nie nadaje się do

celów komercyjnych.

Q

Wyposażenie

1

Przełącznik zmiany biegu

2

Przełącznik kierunku obrotów

3

WŁĄCZNIK / WYŁĄCZNIK / Regulacja

prędkości obrotowej

4

Uchwyt na bity

5

Mocowanie paska

6

Pakiet akumulatorów

7

Przycisk do zwalniania blokady pakietu

akumulatorów

8

Przycisk lampki LED

9

Lampka LED

10

Lampka LED informująca o stanie naładowania

akumulatorów

11

Przycisk stanu naładowania akumulatorów

12

Robocza lampka LED

13

Uchwyt wiertarski

14

Nastawienie momentu obrotowego

15

Ładowarka

16

Czerwona dioda kontrolna

17

Zielona dioda kontrolna

Q

Zakres dostawy

1 Wiertarko-wkrętarka akumulatorowa z

pakietem akumulatorόw

1 Bit PH2 50 mm

1 Ładowarka

1 Walizka do transportu i przechowywania

1 Instrukcja obsługi

Q

Dane techniczne

PABS 18-Li B2 Wiertarko-wkrętarka

Akumulatorowa:

Napięcie znamionowe: 18 V

Liczba obrotόw biegu

jałowego: 1. bieg: maks. 400 min

-1

Liczba obrotόw biegu

jałowego:

2. bieg: maks. 1400 min

-1

Zakres naprężenia

uchwytu wiertarki: maks. 10 mm

Maksymalny

przekrόj odwiertu: stal: 10 mm,

drewno: 30 mm

Maks. moment obrotowy: 35 Nm

PABS 18-Li B2-1 Akumulator:

Typ: LITOWOJONOWY

Napięcie nominalne: 18 V

Pojemność: 1,5 Ah

Zawartość energetyczna: 27 Wh

PABS 18-Li B2-2 Ładowarka:

WEJŚCIE / Input:

Napięcie nominalne: 230 V∼, 50 Hz

Pobór mocy: 55 W

WYJŚCIE / Output:

Napięcie nominalne: 18 V

Prąd ładowania: 2 A

Czas ładowania: ok. 60 min

Klasa ochrony: II /

Informacje dotyczące hałasu i wibracji:

Wartość pomiarowa hałasu wyznaczona zgodnie

z EN 60745. Poziom hałasu elektronarzędzia wg

oceny A wynosi typowo:

Poziom ciśnienia hałasu: 76 dB(A)

Pozom mocy hałasu: 87 dB(A)

Niepewność pomiaru K: 3 dB

Sumaryczne wartości drgań (suma wektorów z trzech

kierunków) wyznaczone zgodnie z EN 60745:

Wkręcanie śrub: Wartość emisji drgań

a

h,D

= 0,865 m / s

2

,

Niepewność K = 1,5 m / s

2

,

Wiercenie: Wartość emisji drgań

a

h

= 2,546 m / s

2

,

Niepewność K = 1,5 m / s

2

.

Podany w niniejszych instruk-

cjach poziom drgań wyznaczony został za pomocą

metody pomiarowej określonej w normie EN 60745 i

może zostać użyty do porównania urządzeń. Podany

poziom emisji drgań może być wykorzystywany również

do wstępnego oszacowania przerw w działaniu.

20 PL

Wstęp / Ogólne wskazówki bezpieczeństwa dla elektronarzędzi

Poziom drgań będzie się różnił w zależności od za-

stosowania elektronarzędzia i w niektórych przypad-

kach może przekroczyć wartość podaną w niniejszej

instrukcji. Obciążenie drganiami może wydawać się

mniejsze niż w rzeczywistości, jeśli elektronarzędzie

będzie regularnie używane ten sposób.

Wskazówka: Celem dokładnego oszacowania

obciążenia wibracjami w okresie określonego okresu

czasu pracy należy uwzględnić również te okresy,

w których urządzenie jest wyłączone lub wprawdzie

jest włączone, ale w rzeczywistości nie pracuje.

Może to przyczynić się do znacznej redukcji obcią-

żenia wibracjami w całym okresie czasu pracy.

Ogólne wskazówki bezpie-

czeństwa dla elektronarzędzi

Przeczytaj wszystkie

wskazówki dotyczące bezpieczeństwa

oraz

instrukcje! Zaniedbania w przestrzeganiu wskazó-

wek dotyczących bezpieczeństwa oraz w przestrze

ga-

niu instrukcji mogą spowodować porażenie prądem

elektrycznym, pożar i / lub ciężkie obrażenia ciała.

Przechowuj na przyszłość wszystkie

wskazówki dotyczące bezpieczeństwa

oraz instrukcje!

Używany we wskazówkach dotyczących bezpie-

czeństwa termin „narzędzie elektryczne“ odnosi się

do narzędzi elektrycznych zasilanych z sieci (z ka-

blem sieciowym) oraz do narzędzi elektrycznych

zasilanych

z akumulatorów (bez kabla sieciowego).

1.

Bezpieczeństwo miejsca pracy

a) Utrzymywać stanowisko pracy w czy-

stości i dobrze oświetlone. Nieporządek

i nieoświetlone obszary robocze mogą prowa-

dzić do wypadków.

b)

N

ie pracuj przy użyciu urządze-

nia w otoczeniu zagrożonym

eksplozją, w którym

znajdują

się palne ciecze, gazy lub pyły. Urządzeni

a

elektryczne wytwarzają iskry, które mogą za-

palić pył lub pary.

c)

Podczas użytkowania urzą-

dzenia elektrycznego trzymaj

dzieci i inne osoby z daleka

od urządzenia. Przy odchyleniu możesz

stracić kontrolę nad urządzeniem.

2.

Bezpieczeństwo elektryczne

a) Wtyk sieciowy urządzenia musi

pasować do wtykowego gniazdka

sieciowego. W żaden sposób nie wol-

no zmieniać wtyku sieciowego urzą-

dzenia. Nie używaj żadnych wtyków

adapterowych razem z urządzeniami

wyposażonymi w uziemienie ochron

ne.

Niezmienione wtyki sieciowe i pasujące wtykowe

gniazdka sieciowe zmniejszają ryzyko poraże-

nia prądem elektrycznym.

b) Unikaj kontaktu fizycznego z powier-

zchniami uziemionymi takimi jak po-

wierzchnie rur, grzejników, kuchni

elektrycznych i lodówek. Istnieje podwyż-

szone niebezpieczeństwo porażenia prądem

elektrycznym, gdy twoje ciało jest uziemione.

c) Trzymaj urządzenie z daleka od desz-

czu i wilgoci. Wniknięcie wody do urządzenia

elektrycznego zwiększa ryzyko porażenia prą-

dem elektrycznym.

d)

Nie używaj kabla sieciowego w

sposób sprzeczny z jego prze-

znaczeniem, tj. do noszenia

urządzenia, zawieszania urzą dzenie

lub do wyciągania wtyku sieciowego

z wtykowego gniazdka sieciowego.

Trzymaj kabel z daleka od gorąca,

oleju, ostrych krawędzi lub porusza-

jących się części urządzeń. Uszkodzone

lub poplątane kable zwiększają ryzyko pora-

żenia prądem elektrycznym.

e)

Gdy pracujesz z urządzeniem elektrycz-

nym na dworze używaj wyłącznie

prze-

dłużaczy, które są dopuszczone również

do pracy na dworze. Użycie

przedłużacza

przystosowanego do stosowania na dworze

zmniej-

sza ryzyko porażenia prądem elektrycznym.

Ogólne wskazówki bezpieczeństwa dla elektronarzędzi

Strona jest ładowana ...

Parkside PABS 18-LI B2 Operation and Safety Notes

Parkside PABS 18-LI B2 Operation and Safety Notes

w innych językach

Powiązane dokumenty

Inne dokumenty