Novus NVIP-4DN2002H/IR-1P-II Instrukcja obsługi

U ser’s manual

( short form)

NVIP-4DN2002H/IR-1P-II

NVIP-4DN2002H/IR-1P-II - User’s manual (short) ver 1.0

2

IMPORTANT SAFEGUARDS AND WARNINGS

INFORMATION

EMC (2014/30/UE) and LVD (2014/35/UE) Directives

CE Marking

Our products are manufactured to comply with the requirements of the following directives

and national regulations implementing the directives:

- Electromagnetic compatibility EMC 2014/30/UE.

- Low voltage LVD 2014/35/EC with further amendment. The Directive applies to electrical

equipment designed for use with a voltage rating of between 50VAC and 1000VAC as well as

75VDC and 1500VDC.

WEEE Directive 2012/19/UE

Information on Disposal for Users of Waste Electrical and Electronic Equipment

This appliance is marked according to the European Directive on Waste Electrical and

Electronic Equipment (2012/19/UE) and further amendments. By ensuring this product is

disposed of correctly, you will help to prevent potential negative consequences for the

environment and human health, which could otherwise be caused by inappropriate waste handling of

this product.

The symbol on the product, or the documents accompanying the product, indicates that this appliance

may not be treated as household waste. It shall be handed over to the applicable collection point for

used up electrical and electronic equipment for recycling purpose. For more information about

recycling of this product, please contact your local authorities, your household waste disposal service

or the shop where you purchased the product.

RoHS Directive 2011/65/UE

Information concerning the restriction of use of hazardous substances in electrical

electronic equipment.

Out of concern for human health protection and friendly environment, we assure that our

products falling under RoHS Directive regulations, regarding the restriction of the use of

hazardous substances in electrical and electronic equipment, have been designed and manufactured in

compliance with the above mentioned regulations. Simultaneously, we claim that our products have

been tested and do not contain hazardous substances whose exceeding limits could have negative

impact on human health or natural environment.

Information

The device, as a part of professional CCTV system used for surveillance and control, is not designed

for self installation in households by individuals without technical knowledge.

Excluding of responsibility in case of damaging data on a disk or other devices:

The manufacturer does not bear any responsibility in case of damaging or losing data on a disk or other

devices during device operation.

WARNING!

PRIOR TO UNDERTAKING ANY ACTION THAT IS NOT DESCRIBED FOR THE GIVEN

PRODUCT IN USER’S MANUAL AND OTHER DOCUMENTS DELIVERED WITH THE

PRODUCT, OR IF IT DOES NOT ARISE FROM THE USUAL APPLICATION OF THE

NVIP-4DN2002H/IR-1P-II - User’s manual (short) ver 1.0

3

IMPORTANT SAFEGUARDS AND WARNINGS

WARNING!

THE KNOWLEDGE OF THIS MANUAL IS AN INDESPENSIBLE CONDITION OF A PROPER DEVICE

OPERATION. YOU ARE KINDLY REQUSTED TO FAMILIRIZE YOURSELF WITH THE MANUAL

PRIOR TO INSTALLATION AND FURTHER DEVICE OPERATION.

WARNING!

USER IS NOT ALLOWED TO DISASSEMBLE THE CASING AS THERE ARE NO USER-

SERVICEABLE PARTS INSIDE THIS UNIT. ONLY AUTHORIZED SERVICE PERSONNEL MAY OPEN

THE UNIT.

INSTALLATION AND SERVICING SHOULD ONLY BE DONE BY QUALIFIED SERVICE PERSONNEL

AND SHOULD CONFORM TO ALL LOCAL REGULATIONS.

IMPORTANT SAFEGUARDS AND WARNINGS

1. Prior to undertaking any action please consult the following manual and read all the safety and operating

instructions before starting the device.

2. Please keep this manual for the lifespan of the device in case referring to the contents of this manual is

necessary;

3. All the safety precautions referred to in this manual should be strictly followed, as they have a direct

influence on user’s safety and durability and reliability of the device;

4. All actions conducted by the servicemen and users must be accomplished in accordance with the user’s

manual;

5. The device should be disconnected from power sources during maintenance procedures;

6. Usage of additional devices and components neither provided nor recommended by the producer is forbidden;

7. Mounting the device in places where proper ventilation cannot be provided (e. g. closed lockers etc.) is not

recommended since it may lead to heat build-up and damaging the device itself as a consequence;

8. Mounting the camera on unstable surface or using not recommended mounts is forbidden. Improperly

mounted camera may cause a fatal accident or may be seriously damaged itself. The camera must be mounted

by qualified personnel with proper authorization, in accordance with this user’s manual.

9. Device should be supplied only from a power sources whose parameters are in accordance with those

specified by the producer in the camera technical datasheet. Therefore, it is forbidden to supply the camera

from a power sources with unknown parameters, unstable or not meeting producer’s requirements;

10. Signal cables (conducting TV or / and telemetric signal) should be placed in a way excluding the possibility

of damaging them by accident. Special attention must be paid to cables getting from the camera and

connecting the power supply;

11. To avoid equipment damage, whole TV circuit should be equipped with properly made discharge-, overload-

and lightning protection devices. Usage of separating transformers is advised;

12. Electric installation supplying the device should be designed to meet the specifications given by the producer

in such a way that overloading is impossible;

13. User cannot repair or upgrade the equipment himself. All maintenance actions and repairs should be

conducted only by qualified service personnel;

14. Unplug the camera from the power source immediately and contact the proper maintenance

department when the following occurs:

 Damages to the power cord or to the plug itself;

 Liquids getting inside the device or exposure to strong mechanical shock;

 Device behaves in a way not described in the manual and all adjustments approved by the

manufacturer and possible to apply by user himself, seem not to have any effect;

 Camera or its casing is damaged;

 Atypical behaviour of the camera components can be seen (heard).

NVIP-4DN2002H/IR-1P-II - User’s manual (short) ver 1.0

4

TABLE OF CONTENTS.................................................................................................4

1. FOREWORD INFORMATION..................................................................................5

1.1. General characteristics .....................................................................................5

1.2. Technical specification ....................................................................................6

1.3. Camera dimension ...........................................................................................7

1.4. Package contents..............................................................................................7

2. START-UP AND INITIAL IP CAMERA CONFIGURATION ................................8

2.1. Description of connectors.................................................................................8

2.2. Connecting ethernet cable ................................................................................8

2.3. Camera mounting .............................................................................................9

2.4. Starting the IP camera ....................................................................................10

2.5. Initial configuration via web browser .............................................................11

2.6. Security recommendations for network architecture and configuration ...........12

3. NETWORK CONNECTION UTILIZING WEB BROSWER ...............................13

3.1. Recommended PC specification for web browser............................................13

3.2. Connection with IP camera via web browser...................................................13

4. USING AND CONFIGURING..................................................................................15

4.1. Remote Preview Interface. ..............................................................................15

5. ELECTRIC CONNECTORS ..................................................................................17

5.1. Connecting power supply to the camera. ........................................................17

6. RESTORING FACTORY DEFAULTS ..................................................................17

6.1. Restore factory defaults via web browser ........................................................17

7. INSTALLING SD CARD ........................................................................................17

TABLE OF CONTENTS

NVIP-4DN2002H/IR-1P-II - User’s manual (short) ver 1.0

5

1. FOREWORD INFORMATION

1.1. General Characteristics

 Sensor resolution: 4 megapixels

 Mechanical IR cut filter, IR operation capability

 Min. Illumination from 0 lx with IR LED on

 Wide Dynamic Range (WDR) for enhanced image quality in diverse light conditions

 Digital Noise Reduction (DNR)

 Lens type: varifocal, f=2.7 ~ 13.5mm/F=1.3

 Built-in LED illuminator: 30 pcs LED

 Compression: H.264/H265

 Max video processing resolution: 2592x1520

 Multi streaming: three independently configurable streams

 Stream parameters: compression, resolution, speed and quality defined individually for each

video stream

 RTP/RTSP protocol support for video transmission

 Hardware motion detection

 Hardware sabotage detection (lens shade)

 Built-in webserver: camera configuration through the website

 Wide range of responses to alarm events: e-mail with attachment, saving file on FTP server, SD

card recording

 Six advanced image analysis functions

 Four privacy zones

 Eight definable Region of Interest

 Power supply: 12VDC, PoE (Power over Ethernet 802.3af)

Information

Depending on the type of recorder/registration system, the range of features and options may vary. Full

list of camera functionality available from a given type of recorder is included in the instruction manual

on www.novuscctv.com/en

Information!

The manufacturer reserves the right to printing errors and technical specifications changes

without prior notice.

FOREWORD INFORMATION

NVIP-4DN2002H/IR-1P-II - User’s manual (short) ver 1.0

6

1.2. Technical specification

FOREWORD INFORMATION

Image

Image Sensor 4 MPX CMOS sensor 1/3” OV

Number of Effective Pixels 2688 (H) x 1520 (V)

Min. Illumination

0.06 lx/F1.3 - color mode,

0 lx (IR on) - B/W mode

Electronic Shutter auto/manual: 1/5 s ~ 1/20000 s

Digital Slow Shutter (DSS) up to 1/5 s

Wide Dynamic Range (WDR) yes (double scan sensor), 90dB

Digital Noise Reduction (DNR) 2D, 3D

Defog Function (F-DNR) yes

Back Light Compensation (BLC) yes

Lens

Lens Type varifocal, f=2.7 ~ 13.5 mm/F1.3

Day/Night

Switching Type mechanical IR cut filter

Switching Mode auto, manual

Switching Delay 1 ~ 36 s

Visible Light Sensor yes

Network

Stream Resolution

2592 x 1520, 2304 x 1296, 2048 x 1520, 1920 x 1080 (Full HD), 1280 x

960, 1280 x 720 (HD), 704 x 576, 640 x 480 (VGA), 320 x 240 (QVGA)

Frame Rate

20 fps for 2592 x 1520,

30 fps for 2048 x 1520 and lower resolutions

Multistreaming Mode 3 streams

Video/Audio Compression H.264, H.265/-

Number of Simultaneous Connections max. 10

Bandwidth 63 Mb/s in total

Network Protocols Support

HTTP, TCP/IP, IPv4, FTP, DHCP, DNS, DDNS, NTP, RTSP, RTP, UPnP,

SMTP

ONVIF Protocol Support Profile S (ONVIF 2.6)

Camera Configuration

from Internet Explorer browser

languages: Polish, English, Russian, and others

Compatible Software NMS

Other functions

Privacy Zones 4

Motion Detection yes

Region of interest (ROI) 8

Video Content Analysis (VCA)

abandoned object, object disappearance, line cross, zone entrance,

face detection, pedestrian detection, cross counting

Image Processing 180˚ image rotation, corridor mode, vertical flip, horizontal flip

Prealarm/Postalarm up to 5 s/up to 300 s

System Reaction to Alarm Events e-mail with attachment, saving file on FTP server, saving file on SD card

NVIP-4DN2002H/IR-1P-II - User’s manual (short) ver 1.0

7

FOREWORD INFORMATION

1.3. Camera dimensions

Dimensions in the drawing are given in millimeters

1.4. Package contents

After you open the package make sure that the following elements are inside:

 IP camera

 Accessories bag

 Short version of user’s manual

CAUTION!

If the device was brought from a location with lower temperature, please wait until it reaches

the temperature of location it is currently in. Turning the device on immediately after bringing it

from a location with lower ambient temperature is forbidden, as the condensing water vapour

may cause short-circuits and damage the device as a result.

Before starting the device familiarize yourself with the description and the role of particular

inputs, outputs and adjusting elements that the device is equipped with.

IR LED

LED Number 30

Range 40 m

Angle 120°

Interfaces

Network Interface 1 x Ethernet - RJ-45 interface, 10/100 Mbit/s

Memory Card Slot microSD - capacity up to 128GB

Installation parameters

Dimensions (mm) with bracket: 84 (Ф) x 241 (L)

Weight 0.7 kg

Degree of Protection IP 66 (details in the user’s manual)

Enclosure

aluminium, white, fully cable managed wall mount

bracket in-set included

Power Supply PoE, 12 VDC

Power Consumption 2 W, 8 W (IR on)

Operating Temperature -35°C ~ 60°C

NVIP-4DN2002H/IR-1P-II - User’s manual (short) ver 1.0

8

1

2

2. START-UP AND INITIAL CAMERA CONFIGURATION

2.1. Description of connectors

1. Power supply 12VDC

2. 100 Mb/s Ethernet port (RJ-45 hermetic connector)

2.2. Connecting ethernet cable

To maintain tightness of ethernet cable connection, please follow instruction below:

1. Unscrew the nut (b) from the connector cover (a), mount the sealing ring on the socket (c)

2. Route the network cable through the components (a) and (b). Plug the RJ-45 connector into the

socket(c)

3. Screw the connector cover (a) on the socket (c). Inside the upper part of the connector cover (a) push

in to the stop the seal of the cable (d) - the seal is cut to insert on the network cable.

4. Tighten up to the stop nut (b)

WARNING!

Camera power supply connector is not hermetic. User should seal this connector by himself.

START-UP AND INITIAL CAMERA CONFIGURATION

b a

b

a

c

d

NVIP-4DN2002H/IR-1P-II - User’s manual (short) ver 1.0

9

START-UP AND INITIAL IP CAMERA CONFIGURATION

2.3. Camera mounting

To mount a camera please follow the instructions below:

 Put the bracket to the wall in a desired mounting place (with cable hole)

 Taking the bracket’s base screw holes as a pattern, mark future drilling holes for screws.

 Drill holes in accordance with previously done markings and base hole placement.

 Connect the cables and mount the camera with bracket on the ceiling/wall with three supplied

self tapping screws.

 Loosen screws “A”.

 Adjust camera position, set appropriate field of view and focus (regulators are located under

the lid "B")

 Tighten screws “A”.

WARNING!

Please note that the wall or ceiling should be even and must have enough strength to support the

camera.

WARNING!

When installing the bracket on rough/uneven surfaces, please additionally seal the junction with

appropriate sealing mass. Please pay special attention to any mounting holes and if they are a

loop-through ones, seal them too.

WARNING!

The declared degree of protection of the camera relates to its housing and does not take into

account the possibility of moisture infiltration into the interior of the camera by connecting

cables. Connection cables protection through i.e. sealing up is the responsibility of the camera

installer. The manufacturer is not liable for any damages to the camera caused as a result of

failing in performing that activity by installer, which also means that camera damaged in that

way is not subject to warranty repairs.

Focus

Zoom

A

B

NVIP-4DN2002H/IR-1P-II - User’s manual (short) ver 1.0

10

START-UP AND INITIAL CAMERA CONFIGURATION

2.4. Starting the IP camera

To run NOVUS IP camera you have to connect ethernet cable between camera and network switch.

To power it up you can connect it directly via power supply adapter with parameters compatible with

camera power supply specification, or camera can be powered with PoE (IEEE 802.3af ) compatible

switch.

After connecting power supply it takes about 30 seconds to start camera. Then You can proceed to

connect to the camera via web browser.

The recommended way to start an IP camera and perform its configuration is a connection directly

to the network switch which is not connected to other devices. To obtain further information about

network configuration parameters (IP address, gateway, network mask, etc.) please contact your

network administrator.

 Connection utilising network switch with PoE support

 Connection utilising external power supply and network switch

Network transmission

Network switch

Computer

IP

Computer

IP

Power supply and network

transmission

Network transmission

Network PoE switch

NVIP-4DN2002H/IR-1P-II - User’s manual (short) ver 1.0

11

START-UP AND INITIAL CAMERA CONFIGURATION

 Connection utilising external power supply directly to the computer

2.5. Initial configuration via the web browser

The default network settings for NVIP-4DN2002H/IR-1P-II camera are:

1. IP address= 192.168.1.200

2. Network mask - 255.255.255.0

3. Gateway - 192.168.1.1

4. User name - root

5. Password - pass

Knowing the camera’s IP address you need to appropriately set PC IP address, so the two devices can

operate in one network subnet ( e.g. for IP 192.168.1.1, appropriate address for the camera ranges from

192.168.1.2 to 192.168.1.254, for example 192.168.1.60). It is not allowed to set the same addresses for

camera and PC computer

You can either set a network configuration (IP address, gateway, net mask, etc.) of NOVUS IP camera

yourself or select DHCP mode (DHCP server is required in this method in target network) by using

web browser or by NMS software. When you use DHCP server check IP address lease and its linking

with camera MAC address to avoid changing or losing IP address during device operation or network/

DHCP server breakdown. You have to remember to use a new camera IP address after changing

network parameters.

After network setting configuration has been done, the camera can be connected to a target network.

Network transmission - cross over cable

Computer

IP Camera

NVIP-4DN2002H/IR-1P-II - User’s manual (short) ver 1.0

12

START-UP AND INITIAL CAMERA CONFIGURATION

2.6 Security recommendations for network architecture and configuration

WARNING!

Below are shown security recommendations for network architecture and configuration

of CCTV systems that are connected to the Internet to reduce the risk

of unauthorized interference with the system by a third party.

1. Absolutely change the default passwords and user names (if the device gives this possibility) of

all applied network devices (recorders, cameras, routers, network switches, etc.) to the

severely complexity password. Use lowercase and uppercase letters, numbers, and special characters

if there is such possibility.

2. Depending on the available functionality in the order to restrict access to the used network devices at

the administrator account level, it is recommended to configure the users accounts accordingly.

3. Do not use DMZ function (Demilitarized zone) in your router. Using that function you open the

access to recorder system from the Internet on all ports, which gives possibility for an unauthorized

interference with the system.

Instead of DMZ use port forwarding redirect only the ports which are necessary for the performance

of the connection (detailed information about ports of communication in different models of recorders,

cameras, etc. can be found in the operating instructions).

4. Use routers with firewall function and make sure it is enabled and properly configured.

5. It is recommended to change the default network communication port numbers of used devices

if there is such possibility.

6. If used network devices has a UPnP feature and it is not used, turn it off.

7. If used network devices has a P2P feature and it is not used, turn it off.

8. If used network devices support HTTPS protocol for connection, it is recommended to use it.

9. If used network devices support IP filtering for authorized connections function, it is recommended

to use it.

10. If used recorder has two network interfaces it is recommended to use both of them to physically

separate network for cameras and network for Internet connection. The only device in the system,

accessible from Internet will be recorder - there will be no physically access directly to any camera.

NVIP-4DN2002H/IR-1P-II - User’s manual (short) ver 1.0

13

NETWORK CONNECTION UTILIZING WEB BROWSER

3. NETWORK CONNECTION USING WEB BROSWER

3.1. Recommended PC specification for web browser connections

Requirements below apply to connection with an IP camera, assuming smooth image display

in 2592x1520 resolution and 20 fps speed.

1. CPU Intel Core i3 3GHz or newer

2. RAM Memory min. 4 GB

3. Graphic card NVIDIA GeForce 1 GHz

4. OS Windows VISTA / 7 / 8

5. Network card 10/100/1000 Mb/s

3.2. Connection with IP camera via web browser

You have to enter camera IP address in the address bar. When you connect to the camera, web browser

will download the applet for displaying images from the camera. In Internet Explorer before the first

logon you need to install "SurveillancePlugin.exe” addition. To do this, please click on the link

"Download" and when you get the download window, click "Run" button.

When the addition installer window appears, temporarily close the browser and click "Install" button.

After installation, launch a web browser and connect to the camera.

NVIP-4DN2002H/IR-1P-II - User’s manual (short) ver 1.0

14

If the installation fails, changing security settings for the IE browser is required. In order to do that,

please choose: Tools > Internet options > Security tab > Custom level and:

 Under Download unsigned ActiveX controls - select either Enable or Prompt

 Under Initialize and script ActiveX controls not marked as safe - select Enable or Prompt

You can also add the camera’s IP address to “trusted zone” and set lowest security level for it.

In addition, when working in Windows Vista / 7 / 8 the ActiveX applet may be blocked by Windows

Defender or User account control. In such case you should allow to run this applet, or simply disable

these functions.

When the addition is installed it will be possible to log into the camera. On the login page, enter your

login information. Here can also change the language of the camera interface can be maid.

For safety reasons, we recommend to change the default password and user name.

NETWORK CONNECTION UTILIZING WEB BROWSER

NVIP-4DN2002H/IR-1P-II - User’s manual (short) ver 1.0

15

USING AND CONFIGURING

4. USING AND CONFIGURING

4.1. The Remote Preview Interface

1. The selection buttons to select the stream to be displayed in the Remote Preview window.

2. Live Preview window.

Double-clicking the left mouse button on the preview window enables and disables the display of

the image on the full screen.

3. Buttons for selecting the operating mode and configure the camera:

Live - enables preview live stream

Playback - displays the playback panel

Remote Setting - displays the configuration panel camera

Local Setting - displays the configuration panel of paths to snapshots folders

4. Icon to access to the camera:

USING AND CONFIGURING

- displays information about the logged in user and the version of the applet

- logout from the camera

6. 8. 7.

4.

1.

5.

3. 2.

NVIP-4DN2002H/IR-1P-II - User’s manual (short) ver 1.0

16

5. Enable/disable panel to set the image parameters:

The panel is the ability to adjust the hue,

brightness, contrast, color saturation and

Sharpness.

6. Enable/disable live preview

7. Buttons to set the size and aspect ratio:

8. Additional features control icons:

Information

A description of all functions of the camera is included in the full user manual, posted on the product

page on www.novuscctv.com/en

USING AND CONFIGURING

- sets the original aspect ratio

- fits the image to the browser window

- sets full screen

- enables and disables enlarge the picture

- enables and disables the record a video stream on your computer

- performs a screenshot and saves on your computer

- option inactive

NVIP-4DN2002H/IR-1P-II - User’s manual (short) ver 1.0

17

ELECTRIC CONNECTORS AND RESTORING FACTORY DEFAULTS

5. ELECTRIC CONNECTORS

5.1. Connecting power supply to the camera.

Camera can be supplied using external power supply unit corresponding with the camera parameters or

by using RJ45 network socket and PoE (802.3af) power supply unit.

Information:

Power supply adapter is not included. Please use power adapter with parameters specified in user’s

manual.

WARNING!

In order to provide protection against voltage surges/lightning strikes, usage of appropriate surge

protectors is advised. Any damages resulting from surges are not eligible for service repairs.

Caution:

It is forbidden to use – as the camera power source – PoE equipment (adapters, etc.) not

compatible with IEEE 802.3af standard (items called “passive PoE power supply”). Damages that

results from the usage of improper power supply source are not covered by the warranty.

6. RESTORING FACTORY DEFAULTS

6.1. Restoring factory defaults

Camera NVIP-4DN2002H/IR-1P-II allows you to reset your settings to the factory values. To restore

the camera settings to the default, go to the "Load Default" tab (Remote Setting -> Advanced -> Load

Default). Then select options and functions of the camera whose settings are to be reset and press the

"Save" button. After about 30 seconds, you can re-connect to the camera (at the current IP address, as

long as it was not reset network settings or on the default IP address).

7. INSTALLING SD CARD

The microSD card slot is located in the back of the camera case, under the cover.

28.12.2017 TF MK v1.0

AAT Holding S.A.

431 Pulawska St., 02-801 Warsaw, Poland

tel.: +4822 546 07 00, fax: +4822 546 07 59

www.novuscctv.com

i ns tr u k c j a o bs łu gi

( sk r ó co na )

NVIP-4DN2002H/IR-1P-II

NVIP-4DN2002H/IR-1P-II - Skrócona instrukcja obsługi wer. 1.0

2

UWAGI I OSTRZEŻENIA

Dyrektywy EMC (2014/30/UE) i LVD (2014/35/UE)

Oznakowanie CE

Nasze produkty spełniają wymagania zawarte w dyrektywach oraz przepisach krajowych

wprowadzających dyrektywy:

- Kompatybilność elektromagnetyczna EMC 2014/30/UE.

- Niskonapięciowa LVD 2014/35/UE. Dyrektywa ma zastosowanie do sprzętu elektrycznego

przeznaczonego do użytkowania przy napięciu nominalnym od 50VAC do 1000VAC oraz od

75VDC do 1500VDC.

Dyrektywa WEEE 2012/19/UE

Informacja dla użytkowników o pozbywaniu się urządzeń elektrycznych i elektronicznych

Niniejszy produkt został oznakowany zgodnie z Dyrektywą WEEE 2012/19/UE oraz

późniejszymi zmianami, dotyczącą zużytego sprzętu elektrycznego i elektronicznego.

Zapewniając prawidłowe złomowanie przyczyniają się Państwo do ograniczenia ryzyka

wystąpienia negatywnego wpływu produktu na środowisko i zdrowie ludzi, które

mogłoby zaistnieć w przypadku niewłaściwej utylizacji urządzenia.

Symbol umieszczony na produkcie lub dołączonych do niego dokumentach oznacza, że nasz produkt

nie jest klasyfikowany jako odpad z gospodarstwa domowego. Urządzenie należy oddać do

odpowiedniego punktu utylizacji odpadów w celu recyklingu. Aby uzyskać dodatkowe informacje

dotyczące recyklingu niniejszego produktu należy skontaktować się z przedstawicielem władz

lokalnych, dostawcą usług utylizacji odpadów lub sklepem, gdzie nabyto produkt.

Dyrektywa RoHS 2011/65/UE Informacja dla użytkowników dotycząca ograniczenia

użycia substancji niebezpiecznych w sprzęcie elektrycznym i elektronicznym.

W trosce o ochronę zdrowia ludzi oraz przyjazne środowisko zapewniamy, że nasze

produkty podlegające przepisom dyrektywy RoHS, dotyczącej użycia substancji niebezpiecznych w

sprzęcie elektrycznym i elektronicznym, zostały zaprojektowane i wyprodukowane zgodnie z

wymaganiami tej dyrektywy. Jednocześnie zapewniamy, że nasze produkty zostały przetestowane i nie

zawierają substancji niebezpiecznych w ilościach mogących niekorzystnie wpływać na zdrowie

człowieka lub środowisko naturalne.

Informacja

Urządzenie, jako element profesjonalnego systemu telewizji dozorowej służącego do nadzoru i

kontroli, nie jest przeznaczone do samodzielnego montażu w gospodarstwach domowych przez osoby

nie posiadające specjalistycznej wiedzy.

Wyłączenie odpowiedzialności w przypadku uszkodzenia danych na dysku lub innych

urządzeniach: Producent nie ponosi żadnej odpowiedzialności w przypadku uszkodzenia lub utraty

danych na dysku lub innych urządzeniach podczas działania urządzenia.

UWAGA!

OBOWIĄZEK KONSULTOWANIA SIĘ Z PRODUCENTEM PRZED WYKONANIEM

CZYNNOŚCI NIEPRZEWIDZIANEJ INSTRUKCJĄ OBSŁUGI ALBO INNYMI DOKUMENTAMI:

PRZED WYKONANIEM CZYNNOŚCI, KTÓRA NIE JEST PRZEWIDZIANA DLA DANEGO

PRODUKTU W INSTRUKCJI OBSŁUGI, INNYCH DOKUMENTACH DOŁĄCZONYCH DO

Strona jest ładowana ...

Novus NVIP-4DN2002H/IR-1P-II Instrukcja obsługi

Novus NVIP-4DN2002H/IR-1P-II Instrukcja obsługi

w innych językach

Powiązane dokumenty

Inne dokumenty