Sentiotec MySentio Wifi Instrukcja obsługi

Typ
Instrukcja obsługi
Version 10/23 Ident no. 1-053-313
EN
DE
FR
IT
NL
SV
INSTALLATION AND OPERATING INSTRUCTIONS
English
FI
CS
PL
MySentio WiFi
1-053-313 / S-WIFI01
Table of Contents
1. About this instruction manual 3
2. Important information for your safety 3
2.1. Intended use 3
2.2. Safety information for the installer 4
2.3. Safety information for the user 4
3. Product description 5
3.1. Scope of delivery 5
3.2. Optional accessories 5
3.3. Product features 5
4. Installation and connection 6
4.1. MySentio WiFi installation 6
4.2. Connection MySentio WiFi 7
4.3. Connection to home.com4 7
4.4. Connection to PRO B (B2, B3) und PRO C (C2, C3) 7
4.5. Connection to PRO D (D2, D2I, D3, D3I) 8
5. Commissioning 8
6. Overview of functions 11
7. Operation 12
7.1. Home menu 12
7.2. Settings 14
7.3. Device settings 15
7.4. Coloured light settings 16
7.5. Prole 18
8. Troubleshooting 19
8.1. Error messages 19
9. Maintenance 20
10. Disposal 20
11. Technical data 20
EN
Instructions for installation and use p. 3/20
1. About this instruction manual
Read these instructions for installation and use carefully and keep them within
reach of the device. This ensures that you can refer to information on safety and
operation at any time.
Symbols used for warning notices
In these instructions for installation and use, a warning notice located next to
an activity indicates that this activity poses a risk. Always observe the warning
notices. This prevents damage to property and injuries.
ATTENTION!
This keyword is a warning that damage to property can occur.
Other symbols
This symbol indicates tips and useful information.
These installation and operating instructions can also be found in
the downloads section of our website: www.sentiotec.com/downloads.
2. Important information for your safety
2.1. Intended use
Sentiotec WiFi is used to control the sauna remotely.
A sauna heater controlled by the remote start function of the sau-
na control unit must pass the combustion test as specified in
EN 60335-2-53 paragraph 19.101. If the heater does not meet
this requirement, an appropriate safety precaution must be used
(forexample:safetyswitch-oordoormonitoring)
Any use exceeding this scope is considered improper use. Improper
use can result in damage to the product, severe injuries or death.
Instructions for installation and use p. 4/20
2.2. Safety information for the installer
Installation and connection work on the devices may only be
carried out with the power supply disconnected.
Observe the installation instructions for the sauna control unit
used.
Also comply with the regulations applicable at the installation
location.
For your own safety, consult your supplier in the event of prob-
lemsthatarenotexplainedinsucientdetailintheinstallation
instructions.
2.3. Safety information for the user
The WiFi must not be used by children under 8 years of age.
The WiFi may only be used by children over 8 years of age, by
persons with limited psychological, sensory or mental capabilities
or by persons with a lack of experience/knowledge under the
following conditions:
They are supervised.
They have been shown how to use the device safely and
are aware of the hazards that could occur.
Observe the operating instructions for the sauna control unit used.
For your own safety, consult your supplier in the event of prob-
lemsthatarenotdescribedinsucientdetailintheoperating
instructions.
EN
Instructions for installation and use p. 5/20
3. Product description
3.1. Scope of delivery
MySentio WiFi
1 pc. 1 m Ethernet cable, 8-pin RJ45
Installation material
Assembly instructions
3.2. Optional accessories
Home door sensor (1-052-723 / SAB00103)
Safety shutdown (SFE-xxxxx)
3.3. Product features
Sentiotec WiFi enables the functions of all existing sauna control units to be
operated using devices such as smartphones and tablets. This is done using
the MySentio app in a local network (WiFi), which is available free of charge for
Android (Google Play Store) and for iOS (App Store). The subscription is free of
charge for 3 years, after which fees may apply.
Compatible sauna control units:
home.com4 RS485 (1-052-984 / HC4-B-RS485)
Pro B2 (1-015-455 / PRO-B2)
Pro B3 (1-015-457 / PRO-B3)
Pro C2 (1-015-448 / PRO-C2)
Pro C3 (1-015-451 / PRO-C3)
Pro D (only in combination with BUS-CON-D / 1-053-348)
ATTENTION!
Standard-compliant operation
To ensure standard-compliant operation, safety devices must be installed in
accordance with the operating instructions for your sauna control unit.
Instructions for installation and use p. 6/20
ATTENTION!
Interference can impair signal transmission
Route all data cables separately from other mains cables and control cables.
Protect cables with only one layer of insulation by using a conduit (double
insulation).
ATTENTION!
Damage to the device!
Installation of the app and input of the settings (see “6. Overview of functions” and
“7. Operation”) must be completed before the sauna control unit is switched on.
30
27.5
4. Installation and connection
Work may only be carried out when the power has been disconnected.
During installation, observe the technical data on page 20.
1. Secure the WiFi module 1 somewhere near the sauna control unit and within
the range of its network (WiFi) using the screws provided.
2. Sentiotec WiFi is connected to the sauna control unit using the 8-pin Ethernet
cable in accordance with the following diagrams:
3. Make a note of the serial numbers (10 digits) of your devices to ensure you
can enter them in the app later on.
Sauna heater ................................................................................................
Sauna control unit ........................................................................................
Other products ..............................................................................................
4.1. MySentio WiFi installation
EN
Instructions for installation and use p. 7/20
156
193
238
156
238
193
193
156
193
238
156
238
193
193
MySentio WiFi
STB
Auto
FF
rd wt bk
home.com4
PRO B-Serie
PRO C-Serie
PRO D-Serie
STB
Auto
FF
rd wt bk
RJ45
8 pin
RJ45
8 pin
STB
Auto
FF
rd wt bk
MySentio WiFi
RJ45
8 pin
4.2. Connection MySentio WiFi
4.3. Connection to home.com4
4.4. Connection to PRO B (B2, B3) und PRO C (C2, C3)
Instructions for installation and use p. 8/20
5. Commissioning
1. Activate the remote start on the sauna control.
home.com4:
a. Use rotary selector to select the remote start icon.
b.Pressrotaryselectorbrieytostarttheoperatingmode“Standbyforremote
operation”
PRO B (B2, B3):
Press the temperature knob for three seconds to start the operating mode
“Standby for remote operation”(display ashesorCountdownof30sec.)
PRO C (C2, C3):
a. Turn the top knob to the remote start symbol
b. Press the lower knob to start the operating mode “Standby for remote ope-
ration” (display shows „on“ or countdown of 30 sec.)
PRO D (D2, D2i, D3, D3i):
a. Control unit at standby-mode (display shows „---“)
b.PresstheOn/Obuttonandthemodebuttonsimultaneouslyforabout
three seconds to start the operating mode “Standby for remote operation” (dis-
play shows „rc“ or countdown of 30 sec.)
Please note the operating instructions for the respective control unit -
“Standby for remote control”
MySentio WiFi
BUS-Converter
STB
Auto
FF
rd wt bk
STB
Auto
FF
rd wt bk
STB
Auto
FF
rd wt bk
STB
Auto
FF
rd wt bk
RJ12
6 pin
RJ45
8 pin
4.5. Connection to PRO D (D2, D2I, D3, D3I)
EN
Instructions for installation and use p. 9/20
Fig. 1 Signing up/
logging in Fig. 2 Signing up Fig. 3 World of sensations
In case you have forgotten your password, simply enter the email address
you used when you registered. You will then be given instructions on how
to change the password.
To set up the MySentio app, the sauna control MUST be in “standby for
remote control” mode!
2. Download the “MySentio” app onto your smartphone or tablet
Open the app and sign up.
Following the instructions provided in the app.
3. Signing up (Fig. 1–3):
Completealleldsandmakeanoteoftheemailandpasswordyouuse.
Instructions for installation and use p. 10/20
Fig. 4 First steps Fig. 5 Conguration Fig. 6 Select device
Fig. 7 Pairing Fig. 8 Rename Fig. 9 Serial numbers
4. Add a new device: (Fig. 4–5):
Select your device and tap the switch below it. (Fig. 6)
Connect the WiFi to the smartphone by pressing the pairing button.(Fig. 7)
► Renamethedeviceandwaituntiltheapphasnishedloading.(Fig.8)
Select WLAN (must be 2.4 GHz!)
Enter the serial numbers of your devices. (Fig. 9)
EN
Instructions for installation and use p. 11/20
6. Overview of functions
Sentiotec WiFi can only be used to control functions provided by the
sauna control unit in use (for example: Pro-series – NO coloured light,
control units for Finnish sauna mode – NO evaporator)
Sauna temperature
Humidity
Infrared (additional output)
Light switchable
Light dimmable
Fan switchable
Fan dimmable
Preset time
Operating time
Coloured light
User program
home.com4 RS485
XXXX X XXXX
PRO B2
X X X X
PRO B3
X X X X X
PRO C2
X XXXXXXX X
PRO C3
XXXXXXXXX X
PRO D2
X XXXXXX X
PRO D2i
X XXXXXXX X
PRO D3
XX XXXXXX X
PRO D3i
XXXXXXXXX X
Instructions for installation and use p. 12/20
8
Fig. 10 Home menu
7. Operation
2
3
7.1. Home menu
c
7
9
1
a
b
6
4
5
f
e
d
EN
Instructions for installation and use p. 13/20
DANGER!
Makesurethatnoammableobjectsareeverleftonthesaunaheater
when the sauna cabin is put into operation.
1 Devices – switch between devices or add new devices.
2 Settings – see page 14
3 Status–statusdisplay(standby,on,o)
4 Temperature – setting for the preferred temperature (set point)
Increase/decrease temperature using arrow up/down or
bymovingtheameinthecircle
5 Temperature display – shows the selected temperature (set point) when
entering the settings, changes to displaying the measured temperature
(actual value) after 3 sec.
6 Humidity–combimodeon/o–canonlybeswitchedonifthesauna
heater is switched on (see b)
7 Intensity of humidity setting for the preferred humidity (set point)
The maximum humidity set point will depend on the sauna temperature.
The higher the sauna temperature, the lower the maximum humidity value
that can be set (see the operating instructions for the sauna control unit in use)
8 Infrared infraredlampon/o
9 Intensity of infrared – IR lamp dimmer levels 1–7
a Heater–heateron/o
b Light–cabinlighton/o,ifdimmablepressandholdtoenterdevice
settings – see page 15
b Fan–fanon/o,ifvariablepressandholdtoenterdevicesettings
– see page 15
d Coloured light–colouredlighton/o,pressandholdtoenterdevice
settings – see page 15
e Devices – back to the Home menu
f Prole – see page
Sentiotec WiFi can only be used to control functions provided by the
sauna control unit in use (for example: Pro-series – NO coloured light,
control units for Finnish sauna operation – NO evaporator) – see page 11
Press and hold: press the symbol and hold it for 3 seconds
Instructions for installation and use p. 14/20
Fig. 11 Settings
1
2
4
5
1 Device settings – see page 15
2 Colour light settings
– see page 16
3 All o–switchesoallfunc-
tions and consumers at once.
4 User program on/o – there are
5 preset user programs available,
which can be changed.
5 Edit user program the set-
tings in the user programs can
be changed. The settings for
the following functions can be
changed to suit the user’s pref-
erences.
Temperature
Humidity
Infrared
Light
Fan
Coloured light
7.2. Settings
3
EN
Instructions for installation and use p. 15/20
Fig. 12 Device settings
1
2
3
4
5
6
7
8
7.3. Device settings
9
a
b
1 Lighting with heater – switches
on the lighting when the sauna
heater is switched on
2 Cabin light intensity – cabin
light dimming levels (0–100%)
3 Fan intensity – variable fan
output levels (0–100%)
4 Switch-on time – setting for
the maximum period for which
the sauna should operate
continuously.
5 Relay box mode – Only avail-
able with sentiotec WiFi Exten-
sion Box (1-053-315).
6 Time zone – selection of the rel-
evant time zone
7 Recongure WLAN–congure
WLANconnectionoftheWi
module
8 Firmware updates – suggests
new app versions.
9 Info – query information,
such as: software version,
device type, etc.
a Rename – rename the device
in the app.
b Remove – remove the device
from the app.
Instructions for installation and use p. 16/20
Fig. 13 Coloured light settings
7.4. Coloured light settings
1
3
1 Light group on/o – tap to
switchon/o
2 Rename light group – tap to
rename
3 Light group settings tap to
open, then select from colour
and intensity, and tap again to
close
4 Colour – colour setting for
the light group that is open is
displayed – press and hold to
select colours – setting for the
preferred colour entered using
the colour wheel or an individual
colour, or colour rotation
5 Intensity – coloured light dim-
ming levels for the light group
that is open (0–100%)
4
2
5
EN
Instructions for installation and use p. 17/20
1
3
2
4
5
6
7
1 Standard – select from standard colours and colour rotation
2 Colour ring – individual colour selection
3 Colours – tap to select the desired colour
4 Colour ring – individually selectable colours
5 Colour eld – set the white-bordered circle to the desired colour
6 Cancel – closes the colour selection and changes are not applied
7 OK – to apply the selected colour
Fig. 14 Standard colours Fig. 15 Colour ring
Instructions for installation and use p. 18/20
1 Prole – you can change
the following information:
First name
Last name
Email address
► Removeprole
2 Language – select language
3 GTC – general terms and con-
ditions
4 Privacy policy data protection
guidelines
5 Licence agreement – end user
licence agreement
6
Licences – open source licences
7 Logout–logoutofyourprole
8 Version – current version of
the app
Fig. 16 Prole
1
2
3
4
5
6
7.5. Prole
7
8
Fig. 17 Prole
EN
Instructions for installation and use p. 19/20
8. Troubleshooting
8.1. Error messages
The following table describes the possible faults and their causes. Further infor-
mation and assistance can be found in the sentiotec help centre at:
sentiotec.zendesk.com/hc/de
Description Cause/remedy
Cannot connect Make sure that the WiFi network to be
connectedissucientlystrong.
The network name cannot contain any
special characters.
WiFi connection is interrupted
during setup
The name of the WiFi network
contains inadmissible characters.
Cannot connect
or
WiFi connection terminates
during setup
The WiFi module requires access to
port 8883 (secure MQTT), which must
beopenedintherewall.Additional-
ly, there must be access for Network
Time Protocol (NTP) servers. Also
check that other ports are not blocked,
especially 443, 8443 and 8883.
WiFi is not connected
after power failure
Switch the power supply of the sauna
controlunitoandonagain,check
the LED on the WiFi module.
Control LED of the WiFi dongle
does not light up
Check whether power is reaching
the WiFi dongle via the socket on
the sauna control unit.
Control LED of the WiFi dongle
lights up, but still no function
Check that software version of
your controller is compatible.
Error codes: e.g.: 7,2,1 (=A,B,C)
A: WiFi status
B: WiFi connection status
C: AWS connection status
7: WiFi status – AP_RUNNING
2: WiFi connection status – the phone
is not maintaining a connection to
the WiFi module.
1: AWS connection status – AWS con-
nection interrupted, check the internet
and ports of the router.
Also note the error messages of your sauna control unit.
Instructions for installation and use p. 20/20
Dispose of packaging materials in accordance with the applicable
waste disposal regulations.
Used devices contain reusable materials as well as hazardous
substances. Therefore, do not dispose of your used device with
household waste, but do so in accordance with the locally appli-
cable regulations.
9. Maintenance
The device is maintenance-free. An internet connection is used to update it
automatically.
10. Disposal
11. Technical data
Ambient conditions
Ambient temperature: -20 °C to +40 °C
Protection class (protected against splashing water): IP 20
Minimum requirement WiFi 2.4 GHz: 1 Mbit
Control unit
Dimensions: 83 x 56 x 24.5 mm
Operating voltage: 24 V DC max. 10 W
Connection cables
Power supplied by Ethernet cable: 8-pin RJ45 max. 3 m
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181

Sentiotec MySentio Wifi Instrukcja obsługi

Typ
Instrukcja obsługi