Haier AD12MS1ERAD Operating Manual And Instructions

No.0150513771 E

Polski

AD24MS1ERA

AD24MS1ERA(D)

AD28NS1ERA(S)

AD36NS1ERA(S)

AD48NS1ERA(S)

AD12MS1ERA

AD12MS1ERA(D)

AD18MS1ERA

AD18MS1ERA(D)

AD24MS2ERA

AD24MS2ERA(D)

AD28MS2ERA(S)

AD28MS2ERA(S)(D)

DUCT TYPE AIR CONDITIONER

OPERATION MANUAL AND INSTALLATION MANUAL

Contents

Please read this manual carefully before installation.

Keep this operation manual for future reference.

English

Cautions

Safety Precautions

Parts and Functions

Operation

Installation Manual For Wire Controller

Heating Mode

Care and Maintenance

Troubleshooting

Precaution for Installation

Is The Unit Installed Correctly

Installation Procedure

3

4

7

10

14

15

16

17

20

21

22

AD24MS1ERA

AD24MS1ERA(D)

AD28NS1ERA(S)

AD36NS1ERA(S)

AD48NS1ERA(S)

AD12MS1ERA

AD12MS1ERA(D)

AD18MS1ERA

AD18MS1ERA(D)

AD24MS2ERA

AD24MS2ERA(D)

AD28MS2ERA(S)

AD28MS2ERA(S)(D)

CE

All the products are in conformity with the following

European provision:

-Low voltage Directive

-Electomagnetic CompatibilitY

ROHS

Your air conditioning product is marked with this

symbol.This means that electrical and electronic

products shall not be mixed with unsorted

household waste.Do not try to dismantle the

system yourself:the dismantling of the air

conditioning system,treatment of the refrigerant,of oil and of

other part must be done by a qualified installer in accordance

with relevant local and national legislation.Air conditioners

must be treated at a specialized treatment facility for reuse,

recycling and recovery.By ensuring this product is disposed

of correctly,you will help to prevent potential negative cons-

equences for the environment and humen health.Please

contact the installer or local authority for more information.

Battery must be removed from the remote controller and dis-

posed of separately in accordance with relevant local and

nationl legislation.

The products are fulfilled with the requirements in the

council on the Restriction of the use of Certain Hazardous

Substances in Electrical and Electronic Equipment(EU

RoHS Directive)

WEEE

In accordance with the directive 2012/19/EU of the European

parliament,herewith we inform the consumer about the dis-

posal requirements of the electrical and electronic products.

DISPOSAL REQUIREMENTS:

Contains fluorinated greenhouse gases

covered by the Kyoto Protocol

This product contains fluorinated greenhouse gases covered

by the Kyoto Protocol.Do not vent into the atmosphere.

Refrigerant type:R410A

GWP=global warming potential

Please fill in with indelible ink,

1 the factory refrigerant charge of the product

2 the additional refrigerant amount charged in the field

and

1+2 the total refrigerant charge

on the refrigerant charge label supplied with the product.

The filled out label muset be adhered in the proximity of the

product charging port(e.g.onto the inside of the stop value

cover).

A contains fluorinated greenhouse gases covered by the

Kyoto Protocol

B fatory refrigerant charge of the product:see unit name

plate

C additional refrigerant amount charged in the field

D total refrigerant charge

E outdoor unit

F refrigerant cylinder and manifold for charging

Haier Industrial Park, No.1 Haier road, Qingdao,P.R.China

A

B

C

D

kg

R410A

WARNING

If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in

order to avoid a hazard.

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities,

or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance

by a person responsible for their safety.

Children should be supervised to ensure that they do not play with the appliance.

This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or

mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use

of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning

and user maintenance shall not be made by children without supervision.

The appliances are not intended to be operated by means of an external timer or separate remote-control system.

Keep the appliance and its cord out of reach of children less than 8 years.

EUROPEAN REGULATIONS

CONFORMITY FOR THE MODELS

IMPORTANT INFORMATION REGA-

RDING THE REFRIGERANT USED

2011/65/EU

directive of the European parliament and of

GWP:2088

3

Cautions

Disposal of the old air conditioner

Before disposing an old air conditioner that goes out of use, please make sure it's inoperative and safe. Unplug the air conditioner

in order to avoid the risk of child entrapment.

It must be noticed that air conditioner system contains refrigerants, which require specialized waste disposal. The valuable

materials contained in a air conditioner can be recycled. Contact your local waste disposal center for proper disposal of an old

air conditioner and contact your local authority or your dealer if you have any question. Please ensure that the pipework of your

air conditioner does not get damaged prior to being picked up by the relevant waste disposal center, and contribute to environmental

awareness by insisting on an appropriate, anti-pollution method of disposal.

Disposal of the packaging of your new air conditioner

All the packaging materials employed in the package of your new air conditioner may be disposed without any danger to the

environment.

The cardboard box may be broken or cut into smaller pieces and given to a waste paper disposal service. The wrapping bag

made of polyethylene and the polyethylene foam pads contain no fluorochloric hydrocarbon.

All these valuable materials may be taken to a waste collecting center and used again after adequate recycling.

Consult your local authorities for the name and address of the waste materials collecting centers and waste paper disposal

services nearest to your house.

Safety Instructions and Warnings

Damaged air conditioners are not to be put into operation. In case of doubt, consult your supplier.

Use of the air conditioner is to be carried out in strict compliance with the relative instructions set forth in the User's Guide.

Installation shall be done by professional people, don't install unit by yourself.

For the purpose of safety, the air conditioner must be properly grounded in accordance with specifications.

Always remember to unplug the air conditioner before opening inlet grill. Never unplug your air conditioner by pulling on the

power cord. Always grip plug firmly and pull straight out from the outlet.

All electrical repairs must be carried out by qualified electricians. Inadequate repairs may result in a major source of danger for

the user of the air conditoiner.

Do not damage any parts of the air conditioner that carry refrigerant by piercing or perforating the air conditioner's tubes with

sharp or pointed items, crushing or twisting any tubes, or scraping the coatings off the surfaces. If the refrigerant spurts out and

gets into eyes, it may result in serious eye injuries.

Do not obstruct or cover the ventilation grille of the air conditioner. Do not put fingers or any other things into the inlet/outlet and

swing louver.

Do not allow children to play with the air conditioner. In no case should children be allowed to sit on the outdoor unit.

This appliance is not intended for use by persons (including children) with reducedphysical, sensory or mental capabilities, or

lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by

a person responsible for their safety.

Children should be supervised to ensure that they do not play with the appliance.

Before starting the air conditioner, read the information given in the User's Guide carefully. The User's Guide contains very

important observations relating to the assembly, operation and maintenance of the air conditioner.

The manufacturer does not accept responsibility for any damages that may arise due to non-observation of the following

instruction.

4

Safety Precautions

Before starting to use the system, read carefully this "SAFETY PRECAUTIONS" to ensure a proper operation of the system.

Safety precautions described here are classified to " WARNING" and " CAUTION". Precautions which are shown

in the column of " WANING" means that an improper handing could lead to a grave result like a death, serious injury,

etc. However, even if precautions are shown in the column of " CAUTION", a very serious problem could occur depending

on situation. Make sure to observe these safety precautions faithfully because they are very important information to ensure

the safety.

Symbols which appear frequently in the text have following meanings.

Strictly prohibited.

Observe instructions faithfully.

Provide a positive grounding.

When you have read through the manual, keep it always at hand for read consultation. If the operator is replaced, make

sure to hand over this manual to the new operator.

CAUTIONS FOR INSTALLATION

ON

OFF

WARNING

CAUTION

The system should be applied to places as office,

restaurant, residence and the like.

The system should be installed by your dealer or

a professional installer.

When you need some optional devices such as a

humidifier, electric heater, etc., be sure to use the products

which are recommended by us. These devices should

be attached by a professional installer.

Application to inferior environment such as an

engineering shop, could cause equipment

malfunction and serious injury or death.

Installation by yourself is not encouraged because

it could cause such problems as water leakage,

electrical shock or fire accident by some improper

handing.

Installation by yourself is not encouraged because it could

cause such problems as water leakage, electrical shock

or fire accident by some improper handing.

Do not install nearby the place where may have

leakage of flammable gas.

Depending on the place of installation, a circuit

breaker may be necessary.

Drain pipe should be arranged to provide a positive

draining.

If the gas leakes and gathers around, it may cause

the fire.

Unless the circuit breaker is installed, it could cause

elecrical shocks.

Where strong winds may prevail, the system

should be fixed securely to prevent a collapse.

Install on the place where can endure the weight

of air conditioner.

Make sure the system is grounded.

If the pipe is arranged improperly, furniture or the

likes may be damaged by leaked water.

Bodily injury could result by a collapse. Bodily injury could result by a careless installation. Grounding cable should never be connected to

a gas pipe, city water pipe, lightning conductor

rod or grounding cable of telephone. If the

grounding cable is not set properly, it could cause

electric shocks.

WARNING

CAUTIONS FOR TRANSFER OR REPAIR

Modification of the system is strictly prohibited. When the system needs a

repair, consult your dealer.

When the air conditioner is relocated, contact your dealer or a professional

installer.

Improper practice of repair could cause water leakage, electric shock or

fire.

Improper practice of installation could cause water leakage, electric shock

or fire.

Do not wash the air conditioner with water.

Do not install the system where the air outlet

reaches directly the flora and fauna.

Make sure to use a fuse of proper electric rating.

Do not operate the system while the air outlet grill

is removed.

It is strictly prohibited to place a container of

combustible gas or liquid near the air conditioner

or to spray it directly with the gas or liquid.

Neither stand on the air conditioner nor

place something on it.

Do not use the power switch to turn on or off the

system.

Do not touch the air outlet section while the swing

louver is operating.

Do not use such equipment as a water heater, etc.

around the indoor unit or the wire controller.

ON

OFF

It could cause electric shocks. It will not be good for their health. Use of steel or copper wire in place of a fuse is

strictly prohibited because it could result in a trouble

or fire accident.

There is a risk of injury.It could cause a fire accident.There are risks of falling or injury by collapsed

object.

It could cause a fire or water leakage. There is a risk of injury. If the system is operated at the vicinity of such

equipment which generates steam, condensed

water may drip during cooling operation or it could

cause a fault current or short-circuit.

When operating the system simultaneously with

a combustion apparatus, indoor air must be

ventilated frequently.

Check occasionally the support structure of the

unit for any damage after a use of long period of

time.

Insufficient ventilation could cause an oxygen

deficiency accident.

If the structure is not repaired immediately, the

unit could topple down to cause a personal injury.

When cleaning the system, stop the operation and

turn off the power switch.

Do not put water containers on the unit such as a flower vase, etc.

Cleaning should never be done while the internal

fans are running with high speed.

If the water enters into the unit and damages the electric insulation material, it may cause electric shock.

WARNING

CAUTION

CAUTIONS FOR OPERATION

You should refrain from exposing your body directly

to cool wind for a long time.

Do not poke the air inlet or outlet with a bar, etc. When any abnormal condition (scorching smell or

others) is found, stop the operation immediately

and turn off the power switch. Then consult your

dealer.

It could affect your physical condition or cause

some health problems.

Since the internal fan is operating with a high

speed, it could cause an injury.

If you continue the operation without removing the

cause, it could result in a trouble, electric shock

or fire.

The system should never be used for any other

purposes than intended such as for preservation

of food, flora and fauna, precision devices or work

of art.

Do not handle switches with a wet hand. Combustion apparatus should not be placed

allowing a direct exposure to wind of air conditioner.

Incomplete combustion could occur on the

apparatus.

It could cause electric shocks.It could cause deterioration of food or other

problems.

5

Safety Precautions

6

Safety Precautions

1. Applicable ambient temperature range:

The machine is adaptive in following situation

Cooling

Heating

Indoor temperature

Outdoor temperature

Indoor temperature

Outdoor temperature

max. DB/WB

min. DB/WB

max. DB/WB

min. DB/WB

max. DB/WB

min. DB/WB

max. DB/WB

min. DB/WB

32/23 C

18/14 C

46/26 C

10/6 C

27 C

15 C

24/18 C

-15 C

2. If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similar qualified person.

3. If the fuse on the indoor PC board is broken please change it with the type of T 6.3A /250VAC(For series 24,28,36,48).

4. The wiring method should be in line with the local wiring standard.

5. The power cable should be:

H05RN-F 3G 4.0mm

2

(For series 12,18,24);

The connecting cable should be:

H05RN-F 4G 1.3mm

2

(For series 12,18,24,28,36,48)

All the cables shall have got the European authentication certificate. During installation, when the connecting cables

break off, it must be assured that the grouding wire is the last one to be broken off.

6. The power cable and connect cable should be self-provided.

7. The breaker of the air conditioner should be all-pole switch, and the distance between its two contacts should be no

less than 3mm.

8. The indoor unit installation height is at least 2.5m.

9. A leakage breaker must be installed.

10.For AD12MS1ERA and AD12MS1ERA(D),AD18MS1ERA,AD18MS1ERA(D),AD24MS2ERA,AD24MS2ERA(D),

AD28MS2ERA(S),AD28MS2ERA(S)(D),we can get the 4 different ESP through adjust the indoor unit PCB SW1-4 and

SW1-5, please refer below:

Attention: cut off the power supply to adjust the SW1-4, and SW1-5, or else the operation is invalid.

SW1

(1) (2) (3) (4) (5) (6) (7) (8)

Static pressure

10 Pa

30 Pa

50 Pa

70 Pa

OFFOFF

OFFON

ON OFF

ON ON

- - - - - -

Attention:

Unit model with the letter D is the mechine without water pump.

Unit model without the letter D is the mechine with water pump.

AD12MS1ERA AD12MS1ERA(D)

AD24MS1ERA

AD28NS1ERA(S) AD36NS1ERA(S) AD48NS1ERA(S)

AD24MS1ERA(D)

7

Parts and Functions

Electrical components Case

Drain pan Evaporator

Air outlet frame

The pump

drain opening

Electrical components Case

Air outlet frame

Drain pan Evaporator

The pump

drain opening

Air outlet

Air inlet

Duct

The pump

drain opening

Electrical components Case

Drain pan

Evaporator

Air outlet frame

Electrical components Case

Drain pan Evaporator

Air outlet frame

Drain opening

Electrical components Case

Air outlet frame

Drain pan Evaporator

Drain opening

Electrical components Case

Drain pan Evaporator

Air outlet frame

AD18MS1ERA AD24MS2ERA AD28MS2ERA(S) AD18MS1ERA(D) AD24MS2ERA(D) AD28MS2ERA(S)(D)

8

Parts and Functions

Buttons of the wire controller

Reset key

When in abnormal state, push the

reset key with a spike, which may

return the unit to normal

Health switch

Used to control oxygen

function and negative ion

Filter reset

After cleaning air inlet

and filter, press

this switch. The unit

begins to run

ON/OFF switch

Do on and off function. The unit is

on when pressing it; and is off

when pressing it again.

Fan speed switch

Change wind speed

Time switch

It is used to regulate setting time.

Self-inspection

switch

It is used for inspection

service

Air change switch

It is used to open and close air

change function. The mode is as

follows:

No display-air change (automatic)-

air change (RECOVERY)-air

change (NORMAL)

Clock, timing and address setting

Timing switch

It is used for choosing

timing running

Mode switch

Choose running mode

Swing switch

Open and close air flap

TEMP switch

Used for changing set temperature

AUTO

FAN ONLY

COOL

DRY

HEAT

TES

FAN

AUTO

HIGH

LOW

FIX

CENTRAL

OPERATION

STANDBY

PRE-HEAT

DEFROST

FILTER

MODE

HEALTH

SWING

CHECK

UNIT NO.

C

F

DEMAND

CEN. ADD.

SYS. ADD.

MANUAL

ROOM TEMP.

SET TEMP.

TIMER

VENTILATION

CLOCK UP DOWN

ON

OFF

DAILY

AUTO

RECOVERY

NORMAL

MODE FAN SWING

HEALTH

CLOCK

TIMER

CHECK FILTER

RESET

ON/OFF

SET RECOVERY

TEMP

TIME

MED

9

Parts and Functions

Standby display

When the unit is on power and in

"abnormity mode", or outdoor unit

malfunction show alarm , "standby" is

shown to reflect no need to unit.

Display of the wire controller

Remarks

The models in the manual don't have health, filter reset and Air change function.

Running mode display

Show the selected mode

Wind swing display

Filter screen warning

sign

When the sign is

shown, please clean

the filter screen

Centralized display

When controlled by centralized

controller, and chosen by "centralize or

lock" mode, this information is shown.

Timing operation

display

Show timing operation

content

Temperature

display

Display the room

temperature, setting

temperature, and

unit number

Air volume display

Display the setting speed

Inspection status display

Air change display

Health function display

Unit number display

Centralized adress

display

System adress display

Running display

When the compressor runs, it displays.

Demand display

When forced to run,"DEMAND"

will be displayed , or show HH/LL

in the temperature zone.

"Defrost" is shown

when defrosting.

When in preheating

status, "preheating" is

shown.

AUTO

FAN ONLY

COOL

DRY

HEAT

TES

FAN

AUTO

HIGH

LOW

FIX

CENTRAL

OPERATION

STANDBY

PRE-HEAT

DEFROST

FILTER

MODE

HEALTH

SWING

CHECK

UNIT NO.

C

F

DEMAND

CEN. ADD.

SYS. ADD.

MANUAL

ROOM TEMP.

SET TEMP.

TIMER

VENTILATION

CLOCK UP DOWN

ON

OFF

DAILY

AUTO

RECOVERY

NORMAL

MODE FAN SWING

HEALTH

CLOCK

TIMER

CHECK FILTER

RESET

ON/OFF

SET RECOVERY

TEMP

TIME

MED

10

Operation

ON/OFF operation

Press ON/OFF switch on line controller directly

The line controller displays the running state in the latest

time (timing and swing state may not be displayed).

1. Press "ON/OFF" switch.

The air conditioner starts operating, and the light on the

wired controller is on.

3.Press "TEMP" switch

Change set temperature:press TEMP or TEMP every

time, [SET] will display,and set temperature will

increase/reduce

4.Press "FAN SPEED" switch

FAN ONLY Operation:

Press "FAN SPEED" switch to change to

"HIGH"--"MED"--"LOW"--"HIGH"

In AUTO,COOL,DRY,HEAT Operation:

Press "FAN SPEED" switch to change to

"AUTO"--"HIGH"--"MED"--"LOW"--"AUTO"

Avoid pressing "ON/OFF" switch frequently.

Do not press line controller or switches by sharp objects.

The temperature is on the basis of the setting value. The wind temperature may not reach the setting value because of

the outer air conditioner and system protection.

When the wired controller is power on, the screen fully displays it for two seconds. and clock zone "8888"-"888"-"88"-"8"

flicker for 30 seconds. All the switches are invalid at the time.

Remarks

Note

5.Press "swing" switch on the line controller to

swing the wind screen.

6.Press "ON/OFF"switch, off.

The light on the line controller is off.

2.Choose operation mode.

Press "mode"switch to change to

"AUTO"---"FAN ONLY"---"COOL"---"DRY"---"HEAT".

HIGH

C

ROOM TEMP.

COOL

FAN

OPERATION

MODE

CLOCK

MODE FAN SWING

HEALTH

CLOCK

TIMER

CHECK FILTER

RESET

ON/OFF

SET RECOVERY

TEMP

TIME

2

4

5

3

1

6

Several seconds after the operation of the line controller,

the setting of the unit will change.

11

Operation

1.Press "CLOCK" switch

2.Press " " and " " to regulate the time.

Setting of power failure compensation function

When SW1-6 on PCB of wire controller is OFF, it will be in power failure compensation. If the SW1-6 is ON, it has no

compensation function.

When the power is on after blackout, the unit will return to the former state if compensation function is set. Otherwise, it

will stop. When restarting the unit, press "ON/OFF" switch on wired controller.

3.Press "setting" switch. The setting is achieved.

"CLOCK" flickers, and the time displayed is the real time.

The time increases a minute each time you press " " switch.

The time decreases a minute each time you press " " switch.

If not in timing, the screen displays the real time.

If in timing, the screen displays the timing time.

If you want to know the real time, go to the first step.

Notes

The timing is based on the real time. Thus, the real time should be regulated in advance.

The clock regulation steps are as follows:

123

HIGH

C

ROOM TEMP.

HEAT

FAN

OPERATION

MODE

CLOCK UP

MODE FAN SWING

HEALTH

CLOCK

TIMER

CHECK FILTER

RESET

ON/OFF

SET RECOVERY

TEMP

TIME

Present time setting

12

Operation

2.Set up "TIMER"

The display changes with the following sequence:

on

OFF

CYCLE

ON

no display

1.Press "TIME" switch.

The shorter setting time will be carried out firstly.

If the ON timing and OFF timing are the same, the setting is invalid.

Even in timing condition, you may start or close the unit through pressing "ON/OFF" switch.

Notes

Timing setting

Press "ON/OFF" switch

firstly, and set up operation

mode.

Please regulate the clock in

advance before using the

timing function.

3.Time setting is achieved. Press"setting"switch.

If you want to change the timing mode to normal operation,

press "timing" until there is no timing display. When the

timing is invalid, the mode is in normal operation.

Cancel timing

1.The unit starts or stops at the setting time. Meanwhile, it displays the timing time.

2."ON Timing, OFF timing and circulation"means that the unit is on and off at the setting time everyday.

When timing ON or timing OFF flickers, press " " or " " to

regulate the time

Press" "or " "set up ON/OFF time.

The setting time increases ten minutes each time you press " "

switch.

The setting time decreases ten minutes each time you press " "

switch.

When setting timing ON and timing OFF at the same time,

press "timing" switch to change the setting item.

on

OFF

HIGH

C

ROOM TEMP.

123

COOL

FAN

OPERATION

MODE

TIMER

ON

MODE FAN SWING

HEALTH

CLOCK

TIMER

CHECK FILTER

RESET

ON/OFF

SET RECOVERY

TEMP

TIME

OFF timing: when a set time has elapsed, the unit stops running.

ON timing: when a set time has elapsed, the unit starts.

parts of wired controller explanation :

1. Switches or jumper wire must be adjusted when the wire controller is powered off. If the wire controller is

powered on, the above operations will be invalid.

2. Function difference between master wire controller and slave one:

Notes

Factory Setting OFF default settingSW1-8

Installation Manual For Wire Controller

Factory Seting ON default settingSW1-7

13

Operation

Query indoor malfunction history:

In the state of power on or power off, press [CHECK] button, enter the malfunction-querying mode of all indoor units in

the group. Then [CHECK] and [UNIT NO.] will display, and the actual indoor numbers will be displayed in some sequence

(unit number is in decimals). At the same time, in the time region, there will be the current malfunction and the latest time

malfunction, the displaying format is [XX:YY], in which XX stands for the current malfunction, if normal, it will display "--";

YY stands for the latest time malfunction. The failure code of every unit will display for 3 seconds. After the failure codes

of all indoor units in the whole group are displayed, the mode will quit automatically.

How to change the function switches?

Master wire

controller

Slave wire controller

Function All of functions

Only with below functions: ON/OFF, MODE, FAN

SPEED, SET TEMP., SWING

Contrastive

items

No. Type State of switch Function description

Select the master or

the slave controller

ON set as the slave controller

OFF

SW1-1

OFF set as the master controller

Select the controller

mode

ON

standard controller

SW1-2

air handler controller

Room temperature

display option

ON

visible room temperature

SW1-3

invisible room temperature

26

o

lock

ON

Unavailable 26

o

lock

SW1-4

available 26

o

lock

Temperature sensor

position option

ON

Sensor of the controller

SW1-5

Sensor in the unit

OFF

Auto restart

ON unavailable

SW1-6

available

OFF

3.Wiring instruction

Use shielded wire between indoor and wire controller.And be earthed on one side, or the unit will not work normally

because of interference.

Note:Confirm the terminal connection firmly, and do not get in tough with shielded wire.

4.Place wire controller on the holder, and pay attention not to pressing any wires.

10.45

Screw holes

5.3

Bracket

Wire controller

1. Take down wire controller from the holder

2. Install the controller holder

According to the position of 2 screw holes on the

holder, drill 2 holes on the wall, and strike the wood

stopper to the holes respectively.

Then align the 2 screw holes of wired controller

holder to the wood stopper, fix the holder on the wall

with wood screw.

Note:Try a wall as flat as possible for installation.

Don't use excessive force to tighten screws,

otherwise, the holder will be damaged.

AUTO

FAN ONLY

COOL

DRY

HEAT

TES

FAN

AUTO

HIGH

LOW

FIX

CENTRAL

OPERATION

STANDBY

PRE-HEAT

DEFROST

FILTER

MODE

HEALTH

SWING

CHECK

UNIT NO.

C

F

DEMAND

CEN. ADD.

SYS. ADD.

MANUAL

ROOM TEMP.

SET TEMP.

TIMER

VENTILATION

CLOCK UP DOWN

ON

OFF

DAILY

AUTO

RECOVERY

NORMAL

MODE FAN SWING

HEALTH

CLOCK

TIMER

CHECK FILTER

RESET

ON/OFF

SET RECOVERY

TEMP

TIME

MED

Installation Manual For Wire Controller

14

5. Wiring connections of wire controller:

Indoor 1

Wire controller

A B C

Wire controller

Polar wire

Indoor 1

Wire controller

A B C

Wire controller

Polar wire

A B C

Wire controller

Polar wire

BC

A B C A B C

ABCABCAB

ABC

CABCABC

Indoor 1 Indoor 2 Indoor N Indoor 15 Indoor 16

Wire controller

Control wiring

of wire

controller

TYPE 2, FOR AD24MS1ERA, AD24MS1ERA(D),AD28/36/48NS1ERA(S)

ABCABC

AB

ABC

C

ABC

A

Indoor 1

Wire controller

port

Indoor 2 Indoor N Indoor 15 Indoor 16

Wire controller

Control wiring

of wire

controller

Wire controller

port

Wire controller

port

Wire controller

port

Wire controller

port

(master unit)

Wire controller

port

Wire controller

port

Wire controller

port

Wire controller

port

Wire controller

port

(master unit)

TYPE 1, FOR AD12/18MS1ERA,AD12/18MS1ERA(D),AD24MS2ERA,AD24MS2ERA(D),AD28MS2ERA(S),AD28MS2ERA(S)(D)

There are three methods to connection wire controller and the indoor units:

A.One wired controller can control max. up to 16 sets of indoor units, and 3 pieces of polar wire must connect the wire

controller and the master unit (the indoor unit connected with wire controller directly), the others connect with the master

unit through 2 pieces of polar wire( 3 pieces for model AD12/18MS1ERA, AD12/18MS1ERA(D),AD24MS2ERA,

AD24MS2ERA(D) and the bridge CN22 CN23 on slave units PCB should be cut

off ).

B. One wire controller controls one indoor unit, and the indoor unit connects with the wire controller through 3 pieces of

polar wire.

C. Two wired controllers control one indoor unit. The wire controller connected with indoor unit is called master one, the

other is called slave one. Master wire controller and indoor unit; master and slave wire controllers are all connected

through 3 pieces of polar wire.

6. Communication wiring:

The wire controller is equipped with special communication wiring in the accessories. 3-core terminal (1-white 2-yellow 3-

red) is connected with the terminal A, B, C of wire controller respectively.

The communication wiring is 5 meter long; if the actual length is more than it, please distribute wiring according to below

table:

Communication wiring length(m) Dimensions of wiring

< 100 0.3mm

2

x3-core shielded wire

100 and <200 0.5mm

2

x3-core shielded wire

200 and <300 0.75mm

2

x3-core shielded wire

300 and <400 1.25mm

2

x3-core shielded wire

400 and <600 2mm

2

x3-core shielded wire

*One side of the shielded sheet of communication wire must be earthed.

, AD28MS2ERA(S), AD28MS2ERA(S)(D)

"HOT KEEP" function

Heating Mode

15

"HOT KEEP" is operated in the following cases.

When heating is started:

In order to prevent blowing out of cool wind, the indoor unit fan stopped according to the room temperature which heating

operation is started. Wait for approx. 2 to 3 minute, and the operation will be automatically changed to the ordinary heating

mode.

Defrosting operation (in the heating mode):

When it is liable to frost, the heating operation is stopped automatically for 5 to 12 minutes once per approx. one hour,

and defrosting is operated. After defrosting is completed, operation mode is automatically changed to ordinary heating

operation.

When the room thermostat is actuated:

When room temperature increases and room temperature controller actuates, the fan speed is automatically changed to

stop under low temperature condition of indoor heat exchanger. When room temperature decreases, air conditioner

automatically changes over to ordinary heating operation.

Heat pump type warming

With the heat pump type warming, the mechanism of heat pump that concentrate heat of outdoor air with the help of

refrigerant to warm the indoor space, is utilized.

Defrosting operation

When a room is warmed with a heat pump type air conditioner, frost accumulates on the heat exchanger of outdoor unit

along with the drop of indoor temperature. Since the accumulated frost reduces the effect of warming, it is necessery to

automatically switch the operation to the defrosting mode. During the defrosting operation, heating operation is interrupted.

Atmospheric temperature and warming capacity

Warming capacity of heat pump type air conditioner decreases along with the drop of outdoor temperature.

When the warming capacity is not sufficient, it is recommended to use another heating implement.

Period of warm-up

Since the heat pump type air conditioner employs a method to circulate warm winds to warm

the entire space of a room, it takes time before the room temperature rises.

It is recommendable to start the operation a little earlier in a very cold morning.

Warming operation

Points to observe

Turn off the power supply switch. Do not touch with wet hand. Do not use hot water or volatile liquid.

ON

OFF

Thinner

Do not

use!

Benzine

Tooth powder

Cleaning the air filter

Do not dry the air filter with fire.

Do not run the air conditioner without the air filter.

Pre-Season Care

See that there are no obstacles blocking the air inlet and air outlet of both indoor and outdoor units.

Make sure that the air filter is not dirty.

Cut in the power supply switch 12 hours before starting run.

Post-Season Care

Operate the unit with FAN mode on a fair day for about half a day to dry the inside of the unit well.

Stop operation and turn off the power supply switch. Electric power is consumed even the air conditioner is in stop.

Clean the air filter and set it in the place.

Care and Cleaning of the unit

Clean with soft and dry cloth.

If it is very dirty, dissolve neutral detergent in the lukewarm water and make the cloth wet with the water. After wiping,

clean off the detergent using clean water.

1.Clean the air filter by lightly tapping it or with the cleaner. It is more effective to clean

the air filter with water.

If the air filter is very dirty, dissolve neutral detergent in the lukewarm water (approx. 30 C),

rinse the air filter in the water, and thoroughly wash the air filter off the detergent

in the plain water.

2.After drying the air filter, set it up on the air conditioner.

Do not open the inlet grill until fan stops completely.

Fan will continue rotating for a while by the law of inertia after operation is being stopped.

CAUTION

Care and Maintenance

16

Please check the following things about your air conditioner before making a service call.

When the air conditioner does not operate properly after you have checked the above mentioned items or when the following

phenomenon is observed, stop the operation of the air conditioner and contact your sales dealer.

The fuse or breaker often shuts down.

Water drops off during cooling operation.

There is a irregularity in operation or abnormal sound is audible.

When the CHECK LED (red) flickers, an irregularity has occurred in the air conditioner.

Unit fails to start

ON

OFF

Is the power source switch

adjust cut in?

Is city supply power in

normal?

Isn't the signal receiving

section exposed to the direct

sunlight or strong illumination?

Isn't the earth leakage breaker

in action?

It is dangerous. Turn off the

power supply switch

immediately and contact the

sales dealer.

Power supply switch is not

ON.

Cooling or heating is not sufficient

Is the thermostat adjust as

required?

Isn't the air filter dirty? Isn't any doors or windows

left open?

Doesn't any obstacle exist at

the air inlet or outlet?

Cooling is not sufficient

Isn't sun-shine invading direct? Isn't any unexpected heating

load generated?

Isn't the room much crowded?

Isn't the swing louver horizontal? (At HEATING mode)

If swing louver is horizontal, the blow wind does not reach floor.

The wind does not blow during

heating operation

Isn't it warming up?

Power

stoppage?

Troubleshooting

17

The followings are not malfunction

Shuru

When the air conditioner is started, when the compressor starts or stops

during operation or when the air conditioner is stopped, it sometimes sounds

"shuru shuru" or "gobo gobo". It is the flowing sound of the refrigerant, and it

is not a trouble.

Water flowing sound is heard.

This is caused by heat expansion or contraction of plastics.Cracking sound is heard.

It smells. Air which blows out from the indoor unit sometimes smells. The smell results

from residents of tobacco smoke or cosmetics stuck inside of unit.

When the air conditioner is used at restaurant etc. where dense edible oil

fume is always exists, white fog sometimes blows out of air outlet during

operation. In this case consult sales dealer for cleaning the heat exchanger.

During operation, white fog comes out

of indoor unit.

Unit does

not start

Wait for

three

minutes

It is switched into the FAN mode during

cooling.

To prevent frost from being accumulated on the indoor unit heat exchanger,

it is sometimes automatically switched to the FAN mode,but it will soon return

to the cooling mode.

Even if the operation switch is turned on, cooling, dehumidifying or heating

is not operable for three minutes after the conditioner is stopped. Because

the protecting circuit is activated. (During this time air conditioner operates

in fan mode.)

The air conditioner can not be restarted

soon after it stops.

Air does not blow or the fan speed can

not be changed during dehumidifying.

During operation, operation mode has

changed over automatically.

Water or steam generates from the outdoor

unit during heating.

When it is excessively cooled during dehumidifying, the blower

automatically repeats reducing and lowering the fan speed.

Isn't the AUTO mode selected?

In the case of AUTO mode, operation mode is changed automatically from

cooling to heating or vise-versa according to the room temperature.

This results when frost accumulated on the outdoor unit is removed (during

defrosting operation).

Troubleshooting

18

Strona jest ładowana ...

Haier AD12MS1ERAD Operating Manual And Instructions

Haier AD12MS1ERAD Operating Manual And Instructions

w innych językach

Powiązane dokumenty

Inne dokumenty