Sharp UA-HD40E Instrukcja obsługi

UA-HD60E, UA-HD50E, UA-HD40E

Operation Manual

Air Purifier with Humidifying Function

EN ESDE PT FR PL NL

ENGLISH

R

“Plasmacluster” and “Device of a cluster

of grapes” are trademarks of Sharp Cor-

poration.

UA-HD60E

UA-HD50E

UA-HD40E

AIR PURIFIER

with Humidifying Function

OPERATION MANUAL

* The number in this technology mark indicates an

approximate number of ions supplied into air of 1 cm

3

,

which is measured around the center of a room with

the “high-density Plasmacluster 7000” applicable ﬂ oor

area (at 1.2 m height above the floor) at the medium

wind volume in humidifying & air purifying mode, or in

air purifying mode, when a humidiﬁ er/air puriﬁ er or an

air purifier using the high-density Plasmacluster ion

evolving device is placed close to a wall. This product is

equipped with a device corresponding to this capacity.

Free standing type

NOTE

The air puriﬁ er draws in room air from the air intake, passes the air through a Pre-

Filter, a Deodorizing Filter and a HEPA Filter inside of the unit, then discharges the air

through the air outlet. The HEPA Filter can remove 99.97% of dust particles as small

as 0.3 microns that pass through the ﬁ lter and also helps absorb odours.

The Deodorizing Filter gradually absorbs odours as they pass through the ﬁ lter.

Some odours absorbed by the ﬁ lters may break down over time, resulting in additional

odour. Depending on the usage environment, especially when the product is used in

extreme environments (significantly more severe than normal household use), this

odour may become strong in a shorter period than expected. If the odour persists, the

ﬁ lters should be replaced.

• The air puriﬁ er is designed to remove air-suspended dust and odour, but not harmful gases (for

example, carbon monoxide contained in cigarette smoke). If the source of the odour still exists, the

air puriﬁ er may not completely remove the odour.

(Common illustration has used “UA-HD60E”.)

Please read before operating your new Air Puriﬁ er

Pre-Filter

Deodorizing Filter

HEPA Filter

E-1

ENGLISH

Thank you for purchasing this SHARP Air

Purifier. Please read this manual carefully

before using the air puriﬁ er.

After reading, keep the manual in a

convenient location for future reference.

FEATURES

CONTENTS

IMPORTANT SAFETY INSTRUCTIONS

...

E-2

• WARNING

• CAUTIONS CONCERNING OPERATION

• INSTALLATION GUIDELINES

• FILTER GUIDELINES

PART NAMES

.............................................

E-5

• FRONT / BACK

• OPERATION PANEL

• DISPLAY ILLUSTRATIVE DIAGRAM

PREPARATION

..........................................

E-7

• FILTER INSTALLATION

• REFILLING THE WATER TANK

OPERATION

...............................................

E-9

• CLEAN AIR HUMIDIFY

• CLEAN AIR

• CLEAN ION SHOWER

• FAN SPEED

• PLASMACLUSTER ION ON/OFF

• CHILD LOCK

USEFUL FUNCTIONS

.............................

E-11

• LIGHTS CONTROL

• ON TIMER

• OFF TIMER

• ADJUSTMENT OF SENSOR

DETECTION SENSITIVITY

CARE AND MAINTENANCE

.................

E-12

• FILTER INDICATOR

• CARE INDEX

• HUMIDIFYING DISINSTALLATION

• WATER TANK

• HUMIDIFYING FILTER

• HUMIDIFYING TRAY AND COVER

• BACK PANEL

• HEPA FILTER/DEODORIZING FILTER

• UNIT

• FILTER REPLACEMENT

TROUBLESHOOTING

............................

E-17

SPECIFICATIONS

....................................

E-20

Unique Combination of Air Treatment

Technologies

Triple Filtration System + Plasmacluster

+ Humidiﬁ cation

TRAPS DUST*

Pre-Filter traps dust and other large

airborne particles.

DECREASES ODOURS

Deodorizing Filter absorbs many common

household odours.

REDUCES POLLEN & MOLD*

HEPA Filter traps 99.97% of particles as

small as 0.3 microns.

FRESHENS

Plasmacluster treats the air similar to the

way nature cleans the environment by

emitting a balance of positive and negative

ions.

HUMIDIFIES

*When air is drawn through the filter

system.

Sensor Technology continuously monitors

air quality, and automatically adjusting

operation based on detected air purity and

humidity.

E-2

IMPORTANT SAFETY INSTRUCTIONS

When using electrical appliances, basic safety precautions should be followed,

including the following:

WARNING

– To reduce the risk of electrical shock, ﬁ re or injury to persons:

•

Read all instructions before using the unit.

•

Use only a 220-240 volt outlet.

• Do not use the unit if the power cord or plug is damaged or the connection

to the wall outlet is loosened.

• Periodically remove dust from the plug.

• Do not insert ﬁ ngers or foreign objects into the air intake or air outlet.

• When removing the power plug, always hold the plug and never pull on the

cord.

Electrical shock and/or ﬁ re from a short circuit may result.

•

Be careful not to damage the power cord, it may cause electric shock, excess

heat or ﬁ res.

• Do not remove the plug when your hands are wet.

• Do not use this unit near gas appliances or ﬁ replaces.

•

When reﬁ lling the Water Tank, cleaning the unit, or when the unit is not in use, be

sure to unplug the unit. Electrical shock and/or ﬁ re from a short circuit may result.

• If the power cord is damaged, it must be replaced by the manufacturer,

its service agent, a Sharp authorized Service Centre or similarly qualiﬁ ed

person in order to avoid a hazard.

•

Only a Sharp Authorized Service Centre should service this air puriﬁ er. Contact

the nearest Service Centre for any problems, adjustments, or repairs.

•

Do not operate when using aerosol insecticides or in rooms where there is

oily residue, incense, sparks from lit cigarettes, chemical fumes in the air, or in

locations where the unit may get wet, such as a bathroom.

•

Be cautious when cleaning the unit. Strong corrosive cleansers may damage the

exterior.

• When carrying the unit, remove the Water Tank and Humidifying Tray ﬁ rst and

hold the unit by handles on both sides.

•

Do not drink the water in the Humidifying Tray or Water Tank.

•

Change the water in the Water Tank daily with fresh tap water and regularly clean

the Water Tank and Humidifying Tray. (See E-13 and E-14). When unit is not in

use, dispose of the water in the Water Tank and Humidifying Tray. Leaving water

in the Water Tank and/or Humidifying Tray may result in mold, bacteria, and bad

odours.

In rare cases, this bacteria may cause harmful physical eﬀ ects.

•

This appliance can be used by children aged from 8 years and above and persons

with reduced physical, sensory or mental capabilities or lack of experience and

knowledge if they have been given supervision or instruction concerning use of

the appliance in a safe way and understand the hazards involved. Children shall

not play with the appliance. Cleaning and user maintenance shall not be made by

children without supervision.

E-3

ENGLISH

NOTE

– Radio or TV Interference

If this air puriﬁ er should cause interference to radio or television reception, try to

correct the interference by one or more of the following measures:

•

Reorient or relocate the receiving antenna.

•

Increase the separation distance between the unit and radio/TV receiver.

•

Connect the equipment into an outlet on a circuit diﬀ erent from that to which the

receiver is connected.

•

Consult the dealer or an experienced radio/TV technician for help.

CAUTIONS CONCERNING OPERATION

•

Do not block the intake and/or air outlet.

•

Do not use the unit near or on hot objects, such as stoves or heaters, or where it

may come into contact with steam.

•

Always operate the unit in an upright position.

• Hold the unit by using the handles on both sides when moving.

Do not move when the unit is in operation.

•

Do not move or change the direction of the main unit while dragging the casters.

•

Lift it up and move such as a soft mat, a ﬂ oor which gets damaged easily, an

uneven place, and thick-poled carpet.

•

When moving by the caster, move it in a horizontal direction.

•

Turn the appliance oﬀ and remove the water tank before moving, take care not to

catch your ﬁ ngers.

• Do not operate the unit without the ﬁ lters, Water Tank, and Humidifying Tray

properly installed.

• Do not wash and reuse the HEPA Filter and the Deodorizing Filter.

Not only does it not improve ﬁ lter performance, it may cause electric shock or

malfunction.

• Clean the exterior with a soft cloth only.

Do not use volatile ﬂ uids and/or detergents.

The unit surface may be damaged or cracked.

In addition, the sensors may malfunction as a result.

• Frequency of maintenance required (descaling) will depend on the hardness

or the impurities of the water that you use; the harder the water the more

often descaling will be necessary.

• Keep the unit away from water.

E-4

IMPORTANT SAFETY INSTRUCTIONS

•

Use only fresh tap water. Use of other water sources may promote the growth of

mold, fungus and/or bacteria.

•

Do not shake the Water Tank when with holding the carrying handle.

•

Do not remove the Humidifying Filter from a Filter Frame.

•

Avoid spilling water when removing or cleaning the Humidifying Tray.

•

Do not remove the Float and the Roller.

Refer to E-18 if the Float and/or Roller comes oﬀ .

•

Do not use the detergents for maintenance of the Humidifying Tray and Cover.

It may cause deformation, tarnishing, cracking (water leakage).

•

Do not scrub the Back Panel hard during its maintenance.

•

Avoid bending or folding the Deodorizing Filter when washing.

INSTALLATION GUIDELINES

• When using the unit, place at least 2 m away from equipment utilizing

electric waves such as televisions or radios to avoid electrical interference.

• Avoid a location where the sensor is exposed to direct wind.

The unit may not operate properly.

• Avoid use in locations where furniture, fabrics or other items may come in

contact with and restrict the air intake and/or air outlet.

• Avoid use in locations where the unit is exposed to condensation or drastic

temperature changes. Appropriate conditions are when room temperature

is between 5 – 35 ºC.

• Place on a stable surface with suﬃ cient air circulation.

When placing the unit on a heavily carpeted area, the unit may vibrate slightly.

Place the unit on an even surface to avoid water leakage from the Water Tank

and/or Humidifying Tray.

• Avoid locations where grease or oily smoke is generated.

The unit surface may crack or the sensor may malfunction as a result.

• Place the unit about 30 cm(1 ft) away from the wall in order to ensure proper

airﬂ ow.

The dust collecting performance will be the same even if using the unit 3cm away

from the wall, but place it as far as possible because it may dirty the wall or ﬂ oor

around.

FILTER GUIDELINES

•

Follow the instructions in this manual for correct care and maintenance of the

ﬁ lters.

E-5

ENGLISH

PART NAMES

FRONT / BACK

1 Air Outlet

(Front)

2 Operation panel

(Ref. E-6)

3 Display

(Ref. E-6)

4 Main Unit

5 Stopper

(2 Locations)

6 Caster

(4 Locations)

1

4

5

6

1 Air Outlet 6 Float

2 Handle

(2 Locations)

7 Humidifying Tray

3 Sensor

(Internal)

•Dust Sensor

•Temperature / Humidity Sensor

•Odour Sensor

(UA-HD60E and UA-HD50E only)

8 Louver

(auto)

9 HEPA Filter

(white)

10 Deodorizing Filter

(black)

11 Back Panel

(Pre-Filter)

12 Air Inlet

4 Water Tank 13 Power Cord / Plug

5 Humidifying Filter

1

2

3

4

5

7

3

2

8

9

10

11

6

13

12

(Plug shape varies by country.)

Dust / Odour Monitor*

The dust / Odour monitor

detects dust in the room

and indicates the intensity

in 5 levels with colour

changes.

*Odour sensor is equipped

with UA-HD60E and UA-

HD50E.

Green

Green (both ends)

Orange (middle)

Orange

Orange (both ends)

Red (middle)

Red

Colour

CLEAN

IMPURE

E-6

OPERATION PANEL

1 POWER ON Button

a CLEAN AIR MODE Button / INDICATOR LIGHT

(green)

b CLEAN AIR HUMIDIFY MODE Button / INDICATOR LIGHT

(green)

c CLEAN ION SHOWER MODE Button / INDICATOR LIGHT

(green)

2 • FAN SPEED Button /

INDICATOR LIGHT

(green)

• Plasmacluster Ion ON / OFF Button

(Press 3 sec.)

/

INDICATOR LIGHT

(green)

5 • LIGHT CONTROL Button

• FILTER RESET Button

(Press 3 sec.)

/

INDICATOR LIGHT

(orange)

3 ON/OFF TIMER Button /

INDICATOR LIGHT

(green)

6 POWER OFF Button

4 CHILD-LOCK Button

(Press 3 sec.)

/

INDICATOR LIGHT

(green)

32 4516

DISPLAY ILLUSTRATIVE DIAGRAM

Humidity Monitor

Indicates approximate humidity level in the room.

Humidity setting cannot be adjusted.

bca

Plasmacluster Ion Light

blue

Plasmacluster Ion ON

oﬀ

Plasmacluster Ion OFF

green

oﬀ

red

(Flash

ing)

Humidity ON

Humidity OFF

need to supply water

Humidify Light

PART NAMES

E-7

ENGLISH

PREPARATION

FILTER INSTALLATION

HEPA Filter (White)

Deodorizing Filter

(Black)

Be sure to remove the power

plug from the wall outlet.

HEPA Filter (White) Deodorizing Filter (Black)

(2 Locations)

Remove the Back Panel.

Remove the ﬁ lters from the

plastic bag.

Install the ﬁ lters in the correct

order as shown.

Install the Back Panel.

Fill in the usage start date on the

Date Label.

1

2

3

4

5

Click

Tag

E-8

CAUTION

REFILLING THE WATER TANK

•

Check to see that there is no water leaking.

• Be sure to wipe oﬀ any excess water on

the outside of the Water Tank.

• When carrying the Water Tank, hold it

with both hands so that the Water Tank

opening is facing up.

When using the Clean Air Humidify Mode, or the Clean Ion Shower Mode.

• Do not expose the unit to water. Short circuit and/or electrical shock may occur as a result.

• Do not use hot water (40 ºC), chemical agents, aromatic substances, dirty water, or other

damaging substances, deformation and/or malfunction may occur.

• Use only fresh tap water. Use of other water sources may promote the growth of mold, fungus and/

or bacteria.

Tighten

CAUTION

Remove the Water Tank by

pushing the handle down and

pulling it forward.

Fill the Water Tank with tap Water.

Install the Water Tank.

1

2

3

Click

MAX

PREPARATION

Be sure to remove the power

plug from the wall outlet.

E-9

ENGLISH

OPERATION

STOP

About Automatic Humidify Mode

The Temperature/Humidity sensors automatically detect and adjust

humidity according to changes in room temperature. Depending on

the size and humidity of the room, humidity may not reach 55~65

%. In such cases, it is recommended that CLEAN AIR HUMIDIFY/

MAX MODE be used.

CLEAN AIR HUMIDIFY

Temperature Humidity

~18 ºC 65 %

18 ºC~24 ºC 60 %

24 ºC~ 55 %

Using to quickly clean the air, reduce odours and to humidify.

• The louver opens and the unit starts the operation

automatically.

• Select the desired fan speed. (Ref. E-10)

• Unless the power cord has been unplugged, the operations

starts in the previous mode it was operated in.

NOTE

• Fill the Water Tank. (Ref. E-8)

• When the Water Tank is empty, the unit will operate in

“CLEAN AIR MODE” and

is ﬂ ashing (red).

lights in (green) during operation of humidiﬁ cation.

START

STOP

CLEAN AIR

Using when additional humidity is not required.

• The louver opens and the unit starts the operation

automatically.

• Select the desired fan speed. (Ref. E-10)

• Unless the power cord has been unplugged, the operations

starts in the previous mode it was operated in.

START

CLEAN ION SHOWER

• The louver opens and the unit starts the operation automati-

cally.

• If the “Plasmacluster Ion ” is OFF,

the plasmacluster ion will be not released.

• When the operation ﬁ nishes, the unit will return to the prior

operation mode.

• It is possible to switch this mode to another while operating.

However, the CLEAN ION SHOWER mode will not function

after switching mode.

• The unit releases Plasmacluster ions with the maximum air

ﬂ ow and collects dusts while decreasing static electricity for

10 minutes. After that, the unit operates while humidifying

with strong air ﬂ ow for 50 minutes.

• The unit stops humidifying and the Humidify Light will turn

oﬀ once humidity reaches a proper level.

• When the Water Tank is empty, the Humidify Light is ﬂ ash-

ing (red) and the unit will operate without humidifying.

Releases high-density Plasmacluster

ions and discharges strong air ﬂ ow for

60 minutes.

NOTE

AUTO

The fan speed is automatically switched (between HIGH and LOW) depending

on the amount of impurities in the air. The sensors detect impurities for eﬃ cient

air puriﬁ cation.

ADVANCED

AUTO

The unit will automatically operate at higher level than the normal with the

intensities of releasing high-density Plasmacluster ions and catching dust.

When humidity reaches at 70% or more, the unit discharges strong air ﬂ ow

continuously.

POLLEN

DUST SENSOR sensitivity is automatically set to “HIGH” and quickly detects

impurities such as dust and pollen to clean the air.

E-10

FAN SPEED

PLASMACLUSTER ION ON/OFF

Select the desired fan speed.

OFF

(In operation)

NOTE

ON

AUTO

ADVANCED

AUTO

POLLEN LOW MED MAX

CHILD LOCK

Operation of the unit display will be locked. It is the same method as starting operation.

ON CANCELLATION

more than 3 sec.

When Plasmacluster ion is OFF,

the Plasmacluster Ion Light (blue)

is turned oﬀ .

OFF

OPERATION

2hour

1hour

10hour6hour

4hour

14hour4hour

2hour

12hour8hour

8hour

CANCELLATION

brighter

darker

turn oﬀ

E-11

ENGLISH

USEFUL FUNCTIONS

High

Standard

Low

LIGHT CONTROL

ON TIMER

OFF TIMER

Use this function to select the desired brightness.

Select the length of time you want. The unit automatically starts once the selected time is reached.

Select the length of time you want, with the unit on. The unit automatically stops once the selected

time is reached.

ADJUSTMENT OF SENSOR DETECTION SENSITIVITY

1

DUST/ODOUR MONITOR is constantly red to reduce sensitivity, and set to “high” if the DUST/

ODOUR MONITOR is constantly green to increase sensitivity.

*Odour sensor is only equipped with UA-HD60E and UA-HD50E.

RED••••••••SET to “LOW”

GREEN•••SET to “HIGH”

2

3

CAUTION

• If the power OFF Button is not pushed within 8 seconds of adjusting sensor

sensitivity, the setting will be saved automatically.

• The sensor sensitivity setting will be saved even if the unit is unplugged.

more than 3 sec.

(with the unit OFF)

1

E-12

CARE INDEX

In case operating at the “MEDIUM” wind volume, the Indicator Light will turn on after approximately

720 hours. (30days×24hours=720)

(The lighting time will vary between approximately 360-1080 hours depending on the wind volume.)

Reminder to perform maintenance of parts below.

After performing maintenance, reset the Filter Indicator. (Ref. E-13)

HUMIDIFYING DISINSTALLATION

frame colour : gray

After maintenance, replace the parts accurately.

FILTER INDICATOR

• Notice an unpleasant odour from the air

outlet.

• Filter performance appears fall and / or

odour persist.

more than 3 sec.

Humidifying Filter

(Ref. E-13)

Water Tank

(Ref. E-13)

Humidifying Tray

(Ref. E-14)

• Filter Indicator Light turn on.

Unit (Ref. E-15)

Back Panel

(Ref. E-14)

Deodorizing Filter

(Ref. E-15)

HEPA Filter

(Ref. E-15)

CARE AND MAINTENANCE

E-13

ENGLISH

WATER TANK

Rinse the inside with a small amount of water.

• Do not shake the Water Tank with holding the carrying handle.

• Do not put down the Water Tank with the Tank Cap on the bottom

side. (The water may leak.)

CAUTION

NOTE

for stubborn dirt...

ToothbrushTank cap

Clean inside of the water tank

with a soft sponge and the

tank cap with a cotton swab or

a toothbrush.

HUMIDIFYING FILTER

Rinse with plenty of water.

CAUTION

• Do not remove the Humidifying Filter from a Filter Frame.

• Avoid spilling water from the Humidifying Tray.

NOTE

for stubborn dirt...

1.

Soak in water with the descaling solution about 30 minutes.

CAUTION

When using lemon juice, soak time more longer.

2.

Remove the descaling solution with plenty of water.

Descaling solution

• Citric acid (available at some drugstores or baking shops)

• 100% bottled lemon juice with no pulp.

stir well!

2 ½ cups of water

3 teaspoons

3 cups of water

¼ cup

stir well!

Be sure to remove the power

plug from the wall outlet.

E-14

Back Panel

HUMIDIFYING TRAY AND COVER

CAUTION

Rinse the inside of the Humidifying Tray with a

toothbrush.

• Do not remove the Float and the Roller.

• If the Float and / or the Roller comes oﬀ . (Ref. E-18)

NOTE

for stubborn dirt...

TRAY

1.

Fill the tray half way with water.

2.

Add a small amount of kitchen

detergent.

3.

Soak for 30 minutes.

4.

Remove the kitchen detergent

with clean water.

BACK PANEL

NOTE

for stubborn dirt...

Gently remove dust with a vacuum cleaner

attachment or similar tool.

Roller

Float

1.

Soak in water with kitchen

detergent about 10 minutes.

DO NOT scrub the back panel

hard.

2.

Remove the kitchen detergent

with clean water.

3.

Dry ﬁ lter completely in a well

ventilated area.

CAUTION

Sensor

CARE AND MAINTENANCE

E-15

ENGLISH

Be sure to remove the power

plug from the wall outlet.

Do not WASH in water and DRY in the sun.

• HEPA FILTER

Apply the maintenance only the side with the tag on. Do not

clean the opposite side.

The ﬁ lter is fragile, so be careful not to apply too much pres-

sure.

• DEODORIZING FILTER

The maintenance can be applied to the both sides.

The ﬁ lter may be broken if being too much power is applied

on it, so please handle it with care.

HEPA FILTER /

DEODORIZING FILTER

UNIT

CAUTION

Wipe with a dry, soft cloth.

•

Do not use volatile ﬂ uids

Benzine paint thinner, polish powder, may damage the

surface.

•

Do not use detergents

Detergent ingredients may damage the unit.

CAUTION

Remove the dust on the HEPA FILTER and

DEODORIZING FILTER.

Tag

HEPA Filter (White)

Deodorizing Filter (Black)

Replacement Filter Model

Please consult your dealer for purchase of replacement ﬁlter.

•HEPA Filter About 10 years after opening

•Deodorizing Filter About 10 years after opening

•Humidifying Filter About 10 years after opening

Use the date label as a reminder for next replacement.

E-16

Replacement timing

Filter life will vary depending on the room environment, usage, and location of the unit. If dust or

odour persists, replace the ﬁ lter.

(Refer to “Please read before operating your new Air Puriﬁ er”)

The following ﬁlter life and replacement period is based on the condition of smoking 5 cigarettes per

day and the dust collection/deodorization power is reduced by half compared with that of new ﬁ lter.

We recommend to replace the ﬁlter more frequently if the product is used in a condition signiﬁcantly

severer than normal household use.

Humidifying Filter

Filter Frame (gray)

FILTER REPLACEMENT

NOTE

AIR PURIFIER MODEL

REPLACEMENT FILTER MODEL

HEPA Filter :

1 unit

Deodorizing

Filter : 1 unit

Humidifying

Filter : 1 unit

UA-HD40E UZ-HD4HF UZ-HD4DF

UZ-HD6MFUA-HD50E UZ-HD4HF UZ-HD4DF

UA-HD60E UZ-HD6HF UZ-HD6DF

HEPA Filter

Deodorizing Filter

Disposal of Filters

Please dispose of used ﬁ lters according to any local laws and

regulations.

HEPA Filter material :

• Filter : Polypropylene

• Frame : Polyester

Deodorizing Filter material :

• Deodorizer : Activated charcoal

• Filter : Polyester, Rayon

Humidifying Filter material :

• Filter : Rayon, Polyester

Filter Frame (white)

Humidifying

Filter

CARE AND MAINTENANCE

Be sure to remove the power

plug from the wall outlet

.

Strona jest ładowana ...

Sharp UA-HD40E Instrukcja obsługi

Ten podręcznik jest również odpowiedni dla

Sharp UA-HD40E Instrukcja obsługi

w innych językach

Powiązane dokumenty

Inne dokumenty