Sage BES810 instrukcja

the Duo-Temp™ Pro

BES810/SES810

the User Guide

B###### / S######

EN USER GUIDE

FR GUIDE UTILISATEUR

IT MANUALE UTENTE

PT MANUAL DO UTILIZADOR

DE HANDBUCH

NL HANDLEIDING

ES GUÍA DEL USUARIO

PL INSTRUKCJA OBSŁUGI

2

CONTENTS

SAGE®

RECOMMENDS

SAFETY FIRST

At Sage® we are very safety

conscious. We design and

manufacture appliances

with your safety foremost in

mind. We also ask that you

exercise a degree of care

when using any electrical

appliance and adhere to

the following precautions.

READ ALL INSTRUCTIONS

BEFORE USE AND SAVE

FOR FUTURE REFERENCE

• A downloadable version of this

document is also available at

sageappliances.com

• Before using for the rst

time, please ensure that your

electricity supply is the same

as shown on the rating label

on the underside of the

appliance. If you have any

concerns please contact your

local electricity company.

• The installation of a residual

current safety switch is

recommended to provide

additional safety when using

all electrical appliances.

Safety switches with a rated

operating current not more

than 30mA are recommended.

Consult an electrician for

professional advice.

• Remove and discard any

packaging materials safely,

before rst use.

• To eliminate a choking hazard

for young children, discard the

protective cover tted to the

power plug safely.

• Ensure the product is properly

assembled before rst use.

• This appliance is for household

use only. Do not use the

appliance for anything other

than its intended purpose.

Do not use in moving vehicles

or boats. Do not use outdoors.

Misuse may cause injury.

• Position the appliance on a

stable, heat resistant, level, dry

surface away from the counter

edge, and do not operate on or

near a heat source such as a

hot plate, oven or gas hob.

• Fully unwind the power cord

before operating.

• Do not let the power cord

hang over the edge of a

counter or table. Do not let the

power cord touch hot surfaces

or become knotted.

• Do not leave the appliance

unattended when in use.

• If the appliance is to be:

- left unattended

2 We Recommend Safety First

5 Getting To Know Your New Appliance

6 Operating Your New Appliance

10 Care & Cleaning

12 Troubleshooting

16 Guarantee

3

EN

WE RECOMMEND SAFETY FIRST

- cleaned

- moved

- assembled; or

- stored

Always switch off the espresso

machine by pressing the

POWER button to OFF.

Switch off and unplug from

the power outlet.

• Regularly inspect the power

cord, plug and actual appliance

for any damage. If found

to be damaged in any way,

immediately cease use of

the appliance and return the

entire appliance to the nearest

authorised Sage Service

Centre for examination,

replacement or repair.

• Keep the appliance and

accessories clean. Follow

the cleaning instructions

provided in this book. Any

procedure not listed in this

instruction booklet should be

performed at an authorised

Sage Service Centre.

• The appliance can be used by

children aged 8 or older and

persons with reduced physical,

sensory or mental capabilities

or a lack of experience and

knowledge, only if they have

been given supervision or

instruction concerning use

of the appliance in a safe

way and understand the

hazards involved.

• Children should not play with

the appliance.

• Cleaning of the appliance

should not be carried out

by children unless they are

8 years or older and under

adult supervision.

• The appliance and its cord

should be kept out of reach

of children aged 8 years

and younger.

• Do not use attachments

other than those provided

with the appliances.

• Do not attempt to operate

the appliance by any method

other than those described in

this booklet.

• Do not move the appliance

whilst in operation.

• Do not use any other liquid

apart from cold mains/town

water. We do not recommend

the use of highly ltered,

de-mineralised or distilled

water as this may affect the

taste of the coffee and how the

espresso machine is designed

to function.

• Never use the appliance without

water in the water tank.

• Ensure the portalter is rmly

inserted and secured into

the brewing head before

using the machine.

• Never remove the portalter

during the brewing operation as

the machine is under pressure.

• Do not place anything, other

than cups for warming, on top

of the appliance.

• Use caution when operating

4

WE RECOMMEND SAFETY FIRST

machine as metal surfaces are

liable to get hot during use.

• Do not touch hot surfaces. Allow

the product to cool down before

moving or cleaning any parts.

• Heating element surface is

subject to residual heat after use.

• Always ensure the appliance

is turned OFF, unplugged at

the power outlet and has been

allowed to cool before cleaning,

attempting to move or storing.

• The appliance is not intended

to be operated by means of

an external timer or separate

remote-control system.

• The use of attachments not

sold or recommended by

Sage may cause re,

electric shock or injury.

• Always turn the appliance to

the off position, switch off at the

power outlet and unplug at the

power outlet when the appliance

is not in use.

• Any maintenance other than

cleaning should be performed

by an authorised Sage®

Service centre.

• Do not use the appliance on a

sink drain board.

• Do not operate the appliance

if it is in an enclosed space,

or within a cupboard.

• Use caution when descaling

as hot steam may be released.

Before descaling, ensure drip

tray is empty and inserted.

Refer to ‘Care & Cleaning’

for further instructions.

SPECIFIC INSTRUCTIONS

FOR WATER FILTER

• Filter cartridge should be kept

out of reach of children.

• Store lter cartridges in a dry

place in the original packaging.

• Protect cartridges from heat

and direct sunlight.

• Do not use damaged

lter cartridges.

• Do not open lter cartridges.

• If you are absent for a

prolonged period of time,

empty the water tank and

replace the cartridge.

The symbol shown

indicates that this

appliance should not be

disposed of in normal

household waste. It should be

taken to a local authority waste

collection centre designated for

this purpose or to a dealer

providing this service. For more

information, please contact your

local council ofce.

To protect against electric

shock, do not immerse the

power cord, power plug or

appliance in water or any

other liquid.

FOR HOUSEHOLD

USE ONLY

SAVE THESE

INSTRUCTIONS

5

EN

GETTING TO KNOW YOUR NEW APPLIANCE

G

I

H

J

A

B

C

D

E

F

A. POWER button

B. Integrated removable tamper

C. Group head

D. 54 mm stainless steel portalter

E. Drip tray full indicator

F. Removable drip tray

G. Cup warming tray

H. SELECT button for steam or hot water

I. Control Dial for espresso, steam and

hot water

J. Swivel steam wand

NOT SHOWN

• Storage tray located behind the drip tray

for storage of accessories

Rating Information

220–240V ~50Hz 1500–1750W

6

GETTING TO KNOW YOUR NEW APPLIANCE

OPERATING YOUR NEW APPLIANCE

CUSTOM DESIGNED

ACCESSORIES

• Razor™ Precision Dose Trimming Tool

• Single wall lter baskets for freshly

ground coffee

• Advanced dual wall lter baskets for

pre-ground coffee

• Water lter

• Stainless steel milk jug

BEFORE FIRST USE

Conditioning the Water Filter

• Remove lter from the plastic bag and soak

in a cup of water for 5 minutes.

• Rinse lter under cold running water.

• Insert the lter into the lter holder.

• Set the dial date 3 months ahead.

• To install lter, push down to lock into place.

• Slide the water tank into position and lock

intoplace.

NOTE

Do not clean any of the parts or

accessories in the dishwasher.

CLEANING ACCESSORIES

• Cleaning tool

• Silicon cleaning disk

• Cleaning tablets

• Descaling powder

FIRST USE

Initial Start Up

• Fill tank with water.

• Press POWER button.

• The machine will reach operating temperature

and go into ‘Standby’ mode.

Flushing the Machine

It is recommended to complete a water ushing

operation, without ground coffee, to ensure the

machine has been conditioned.

When the machine has reached ‘Standby’ mode,

run the following 2 steps.

• Turn the Control Dial to the ‘Espresso’

position for 30 seconds.

• Turn the Control Dial to the ‘Steam’ position

to activate steam for 10 seconds.

• Repeat this cycle several times.

FILLING THE WATER TANK

• Fill the water tank with cold tap water to the

maximum mark on the side of the tank and

slide the water tank back into position at the

back of the machine.

• Plug the power cord into power outlet and

switch On at power point.

• Press the POWER button. The POWER

button surround will ash while the machine

is heating. When the correct temperature

has been reached, all the button surrounds

on the control panel will illuminate.

7

EN

OPERATING YOUR NEW APPLIANCE

SELECTING THE FILTER BASKET

Single Wall Filter Baskets

The Single Wall lters (1 & 2 CUP) are designed

to be used with freshly ground coffee and allow

you to experiment with grind, dose, and tamp

tocreate a more balanced espresso.

2 Cup1 Cup

1 Cup 2 Cup

Dual Wall Filter Baskets

The Dual Wall lters (1 & 2 CUP) are designed to

be used with pre-ground coffee and regulate the

pressure to help optimise extraction and crema

regardless of the grind, dose or tamp pressure.

1 Cup 2 Cup

2 Cup1 Cup

COFFEE PREPARATION

Dosing & Tamping the Ground Coffee

Insert the correct Filter Basket into the portalter.

Fill the Filter Basket with ground coffee, tap down

to collapse the coffee, then using the integrated

tamper, tamp down rmly.

It’s important to apply consistent pressure

every time.

• As a guide to dose, the top edge of the

metal cap on the tamper should be level

with the top of the lter basket AFTER the

coffee has been tamped.

• Wipe excess coffee from the rim of the lter

basket to ensure a proper seal in the group

head is achieved.

TRIMMING THE DOSE

The Razor™ precision dose trimming tool allows

you to trim the puck to the right level for

a consistent extraction.

the Razor™

Precision dose trimming tool

The Razor™ precision dose trimming tool

allows you to trim the puck to the right level for

a consistent extraction.

Dose the Portalter with freshly ground

coffee and tamp down with between 10-15kg

of pressure.

Insert the Razor™ into the coffee basket until its

shoulders rest on the rim of the lter basket.

Rotate the Razor™ dosing tool back and forth

while holding the portalter on an angle over the

knock box to trim off excess coffee.

8

EXTRACTING ESPRESSO

Insert the Portalter into the Group Head &

lock into position. Turn the Control Dial to the

‘Espresso’ position. After a few seconds, coffee

will begin to brew into the cup.

When sufcient coffee has owed into the

cup, turn the Control Dial to ‘Standby’. Sage®

recommends approx. 30 sec of extraction.

NOTE

For optimal avour when using a 1 CUP

lter, you should extract approx. 30ml.

When using a 2 CUP lter, you should

extract approx. 60ml.

NOTE

If machine is run continuously for

30 minutes, allow machine to cool for

5 minutes before each use.

WARNING

The metal parts of the portalter

will be very hot.

EXTRACTION GUIDE

OPERATING YOUR NEW APPLIANCE

TOO

COARSE

TOO FINE

OPTIMUM

TOO LITTLE

INCREASE DOSE

& USE RAZOR

TO TRIM

TOO MUCH

USE RAZOR

TO TRIM 10-15KG OVER

35 SEC

10-15KG UNDER

20 SEC

10-15KG

8-11g (1 CUP)

16-19g (2 CUP) 25-30 SEC

OVER EXTRACTED

BITTER • ASTRINGENT

BALANCED

GRIND DOSE TAMP SHOT TIME

UNDER EXTRACTED

UNDERDEVELOPED • SOUR

9

EN

TEXTURING MILK

• Before inserting the steam wand into the

milk, it is recommended to purge the steam

wand.

• Set the Control Dial to the ‘Steam’ position.

• The ‘Steam’ LED will illuminate.

• Pause the steam by returning the dial back

to the ‘Standby’ position.

• Insert the steam tip below the surface

close to the right hand side of the jug at the

3 o’clock position and set the Control Dial

to the ‘Steam’ position.

• Keep the tip just under the surface until

the milk is spinning clockwise, producing

avortex (whirlpool effect).

• With the milk spinning, slowly lower the

jug, keeping the tip at or slightly below the

surface, until the desired temperature

is reached.

• To stop the steam set the Control Dial to the

‘Standby’ position and remove the jug.

• Wipe the steam wand with a damp cloth.

HOT WATER

To use the Hot Water function:

• Press the ‘SELECT’ button and the Hot

Water LED will illuminate.

• Turn the Control Dial to ‘Steam’.

To turn the hot water off, turn the Control Dial

to the ‘Standby’ position.

OPERATING YOUR NEW APPLIANCE

10

CARE & CLEANING

The water lter provided helps to prevent

scale build up which over time can affect the

performance of your machine, potentially causing

blockages and heating problems.

Replacing the water lter every three months

will reduce the mineral build up in the machine.

If you live in a hard water area, we recommend

you change the water lter more frequently.

PORTAFILTER CLEANING

Periodically run water through the machine with

the portalter in place, but without any ground

coffee, to rinse out any residual coffee particles.

MACHINE CLEANING

After regular use, residual grinds and oil build up

in the machine can affect coffee extraction.

We recommend performing a cleaning cycle

every 2-3 months using the cleaning tablet

provided.

To perform a cleaning cycle:

1. Insert the silicon disk into the portalter.

2. Place the cleaning tablet on the silicon

disk (position in the centre).

3. Insert the portalter into the group head

and rotate to right to lock in position.

4. Ensure Power On/Off button is on.

5. Turn the dial to the ‘Espresso’ position for

20 seconds.

6. Turn the dial back to the ‘Standby’

position.

7. Repeat steps 5-6 three times or until the

cleaning tablet is dissolved.

DESCALING

Even if you are correctly using the water lter

provided, we recommend you to descale when

you see scale build-up in the water tank.

NOTE

Ensure that the water lter is removed from

the water tank before adding the descaling

powder when descaling the machine.

Visit Sage® webpage to purchase “the Descaler”.

1. Ensure the Control Dial is in the ‘Standby’

position, the machine is switched off.

2. Remove the lter holder.

3. Empty one sachet (25g) into 1 litre of

warm water, stir to dissolve.

Pour solution into the water tank.

4. Press the POWER button to switch the

machine on.

5. Place a large container under both the

Group Head and the Steam Wand.

6. Set the Control Dial to the ‘Espresso’

position and let half the descale solution

run through the Group Head.

7. Set the Control Dial to the ‘Steam’

position and allow the remaining solution

to run through the Steam Wand. When

the liquid stops owing, set the Control

Dial back

to the ‘Standby’ position.

8. After descaling, remove the water tank

and rinse thoroughly then rell with fresh

cold water. To rinse the machine, repeat

steps 5-8.

AUTO OFF MODE

The machine automatically switches to AUTO

OFF mode after 20 minutes.

INSTALLING/REPLACING THE

FILTER IN THE WATER TANK

Set current

month

Remove lter

from bag and

soak for 5min

Assemble water

lter parts

Ensure parts

areconnected

Install lter

intank

Install water tank Replace lter

after 90 days

orafter 40L

11

EN

CARE & CLEANING

CLEANING THE STEAM WAND

Run steam to clear milk

from wand after texturing Wipe steam wand after

each use Clean hole with pin Remove tip Soak tip overnight then

re-attach

STORING YOUR MACHINE

Before storing, press the POWER button to off,

turn the Control Dial to ‘Standby’ and unplug.

Insert all accessories into position or into the

storage tray.

Store upright. Do not place anything on top.

WARNING

Do not immerse power cord, power

plug or appliance in water or any

other liquid. The water tank should

never be removed or completely

emptied during decalcifying.

CLEANING FILTER BASKETS

Should the ne holes in the lters become

blocked follow the steps below:

1. Place the lter into the portalter. Run

water through the machine with the lter

and portalter, without any ground coffee,

in place.

2. A pin can be used to clear the lter

basket holes.

3. For a thorough clean of the lters, dissolve

a cleaning tablet in hot water and soak

lters overnight.

CLEANING THE OUTER

HOUSING/CUP WARMING PLATE

The outer housing and cup warming plate can be

cleaned with a soft, damp cloth. Then polish with

a soft, dry cloth.

Do not use abrasive cleansers, pads or cloths

which can scratch the surface.

CLEANING THE DRIP TRAY

The drip tray should be removed, emptied and

cleaned at regular intervals.

Wash the drip tray with warm soapy water, using

a non-abrasive washing liquid, rinse and dry

thoroughly. The drip tray base and cover are

dishwasher safe.

CLEANING THE STORAGE TRAY

The storage tray can be removed after the drip

tray is removed then cleaned with a soft, damp

cloth (do not use abrasive cleansers, pads or

cloths which can scratch the surface).

12

TROUBLESHOOTING

PROBLEM POSSIBLE CAUSES WHAT TO DO

Coffee does not run

through

Machine is not turned On Ensure the machine is

plugged in, switched On at

the power outlet and the

POWER button is pressed.

Water tank is empty Fill the water tank.

The Control Dial not in

‘Espresso’ position

Turn the Control Dial to the

‘Espresso’ position.

Coffee grind is too ne Ensure you use a suitable

espresso grind. Refer to

‘Extraction Guide’ on page 8.

Too much coffee in the lter

basket

Refer to ‘Coffee Dose &

Tamping’, page 7.

Coffee tamped too rmly Refer to ‘Coffee Dose &

Tamping’ on page 7.

The lter is blocked Use a pin to clear the holes.

Please refer to ‘Cleaning

Filter’ on page 11.

Coffee runs out too quickly The coffee grind is too

coarse

Ensure you use a suitable

espresso grind. Refer to

‘Extraction Guide’ on page 8.

Not enough coffee in the

lter

Refer to ‘Coffee Dose &

Tamping’ on page 7.

Coffee not tamped rmly

enough

Refer to ‘Coffee Dose &

Tamping’ on page 7.

Coffee is too cold Cups not preheated Preheat cups.

When the base of the jug

becomes too hot to touch

this is when milk is heated

at the correct temperature.

Refer to ‘Texturing Milk’

on page 9.

13

EN

TROUBLESHOOTING

PROBLEM POSSIBLE CAUSES WHAT TO DO

No crema Coffee is not tamped rmly

enough

Refer to ‘Coffee Dose &

Tamping’ on page 7.

Coffee grind is too coarse Ensure you use a suitable

espresso grind. Refer to

’Extraction Guide’ on page 8.

Ground coffee is not fresh Change to freshly

roasted beans.

Filter holes are blocked Use the ne pin on the

cleaning tool to clear the

holes. Refer to ‘Cleaning

TheSteam Wand’

on page 11.

Machine is making

pulsing/pumping sound

while extracting coffee or

steaming milk

The machine is carrying out

the normal operation of the

15 bar Italian pump

No action required as this

isthe normal operation

of the machine.

Coffee runs out around the

edge of the portalter

Portalter is not inserted into

the group head properly

Insert portalter into the

group head and align with

‘LOCK’ on the group head

collar, until resistance is felt.

There are coffee grounds

around the lter basket rim

Clean any excess ground

coffee from the rim of the

lter basket to ensure

a proper t into the

group head.

Too much ground coffee in

the lter basket

Refer to ‘Coffee Dose &

Tamping’ on page 7.

Ground coffee has been

tamped too rmly

Refer to ‘Coffee Dose &

Tamping’ on page 7.

Incorrect lter for amount of

ground coffee used

Ensure you use the 1 CUP

lter for 1 cup of coffee and

the 2 CUP lter for 2 cups

of coffee.

14

TROUBLESHOOTING

PROBLEM POSSIBLE CAUSES WHAT TO DO

Coffee drips from the

portalter spouts

The water tank is empty

or low

Fill the water tank.

Coffee grind is too ne Ensure you use a suitable

espresso grind. Refer to

‘Extraction Guide’ on page 8.

Too much coffee in basket Refer to ‘Coffee Dose &

Tamping’ on page 7.

Machine is blocked by

mineral deposits

Decalcify the machine. Refer

to ‘Descaling’ on page 10.

Machine is making a loud

and continuous pumping

noise

Water tank is empty Fill the water tank.

Water tank is not securely

in place

Push water tank down

completely to lock

into place.

No steam is generated Machine is not turned on Ensure the machine is

plugged in, switched On

at the power outlet and

the POWER button

is pressed.

Water tank is empty Fill the water tank.

Control Dial not in ‘Steam’

position

Turn the Control Dial to the

‘Steam’ position. Use the

‘SELECT’ button to toggle

to ‘Steam’.

Ensure the ‘Steam’ LED

is illuminated for steam

and the ‘Hot Water’ LED is

illuminated for hot water.

Steam Wand is blocked Use the pin on the cleaning

tool to clear the opening. If

the steam wand continues

to be blocked remove the

tip of the steam wand using

the spanner in the middle of

the cleaning tool. Refer to

‘Cleaning the Steam Wand’

on page 11.

15

EN

TROUBLESHOOTING

PROBLEM POSSIBLE CAUSES WHAT TO DO

No hot water Empty tank Fill the water tank.

Milk is not smooth after

texturing

Steam Wand is blocked Use the pin on the cleaning

tool to clear the opening.

Ifthe steam wand continues

to be blocked remove the

tip of the steam wand using

the spanner in the middle

ofthe cleaning tool. Refer to

‘Cleaning the Steam Wand’

on page 11.

Not enough steam Steam wand may

be blocked. Refer to

‘Cleaning the Steam Wand’

on page 11.

Milk is not cold enough Use cold fresh milk, refer

to ‘Texturing Milk’, page 9.

Machine is not working The safety thermal cut out

may have activated due

to the pump overheating.

Turn the machine off and

allow to cool for about

30-60 minutes.

16

GUARANTEE

2 YEAR LIMITED GUARANTEE

Sage Appliances guarantees this product for

domestic use in specied territories for 2 years

from the date of purchase against defects caused

by faulty workmanship and materials. During

this guarantee period Sage Appliances will repair,

replace, or refund any defective product

(at the sole discretion of Sage Appliances).

All legal warranty rights under applicable

national legislation will be respected and will

not be impaired by our guarantee. For full terms

and conditions on the guarantee, as well as

instructions on how to make a claim, please visit

www.sageappliances.com.

the Duo-Temp™ Pro

the User Guide

B###### / S######

DE HANDBUCH

2

INHALTE

WICHTIGE

VORSICHTS-

MASSNAHMEN

BITTE ALLE ANWEISUNGEN

VOR DEM GEBRAUCH

LESEN UND ZUR

SPÄTEREN BEZUGNAHME

AUFBEWAHREN.

• Dieses Informationsbuch

steht zum Download unter

www.sageappliances.

com zur Verfügung.

• Vor dem ersten Gebrauch

prüfen, dass Ihre

Netzspannung mit der auf

dem Etikett an der Unterseite

des Geräts übereinstimmt.

• Vor dem ersten Gebrauch

alle Verpackungsmaterialien

abnehmen und

sicher entsorgen.

• Schutzhülle am Netzstecker

sicher entsorgen, da

sie für Kleinkinder eine

Erstickungsgefahr

darstellen könnte.

• Dieses Gerät ist nur für den

Haushaltsgebrauch bestimmt.

Gerät nur bestimmungsgemäß

verwenden. Nicht in fahrenden

Fahrzeugen oder Booten

verwenden. Nicht im Freien

verwenden. Missbrauch kann

Verletzungen nach sich ziehen.

• Netzkabel vor dem Gebrauch

SAGE®

EMPFIEHLT:

SICHERHEIT

GEHT VOR

Wir bei Sage® sind sehr

sicherheitsbewusst.

Beim Design und bei der

Herstellung unserer Geräte

denken wir zu allererst an

Ihre Sicherheit. Darüber

hinaus bitten wir Sie, bei

der Verwendung jedes

Elektrogeräts angemessene

Sorgfalt anzuwenden und

sich an die folgenden

Vorsichtsmaßnahmen

zu halten.

2 Wir Empfehlen: Sicherheit

GehtVor

5 Lernen Sie Ihr Neues

GerätKennen

6 Bedienung Ihres Neuen Geräts

10 Reinigung Und Pege

12 Problembeseitigung

16 Garantie

3

WIR EMPFEHLEN: SICHERHEIT GEHT VOR

vollständig entrollen.

• Gerät in sicherem Abstand

von Kanten auf eine stabile,

hitzebeständige, ebene und

trockene Fläche stellen.

Nicht auf oder neben einer

Wärmequelle wie einem Gas-

oder Elektroherd oder einem

heißen Ofen betreiben.

• Netzkabel nicht über

Arbeitsplatten oder Tischkanten

hängen lassen, von heißen

Oberächen fern halten,

Kabelgewirr vermeiden.

• Gerät während des Betriebs

nicht unbeaufsichtigt lassen.

• Zum Schutz gegen Stromschlag

Netzstecker, Netzkabel oder

Gerät nicht in Wasser oder

sonstige Flüssigkeiten tauchen.

• Gerät immer ausschalten,

Netzstecker ziehen und

abkühlen lassen, ehe Sie es

bewegen, reinigen oder lagern.

• Gerät immer ausschalten,

sofern möglich auch an der

Steckdose, und Netzstecker

ziehen, wenn es nicht

in Gebrauch ist.

• Gerät nicht verwenden,

wenn das Netzkabel, der

Netzstecker oder das Gerät

selbst in irgendeiner Weise

beschädigt ist. Wenden Sie

sich bei Schäden oder zur

Wartung (außer Reinigung) bitte

an den Sage-Kundendienst

oder besuchen Sie

sageappliances.com

• Alle Wartungsarbeiten außer

Reinigung nur von autorisierten

Sage®-Kundendienststellen

vornehmen lassen.

• Kinder nicht mit dem Gerät

spielen lassen.

• Reinigung des Geräts nicht

von Kindern unter 8 Jahren

und nur unter Aufsicht

vornehmen lassen.

• Gerät und Netzkabel für

Kinder bis zu 8 Jahren

unzugänglich aufbewahren.

• Die Installation eines Schutz-

oder Sicherheitsschalters

wird bei der Verwendung

von Elektrogeräten als

zusätzliche Schutzmaßnahme

Sage BES810 instrukcja

Sage BES810 instrukcja

w innych językach

Powiązane dokumenty

Inne dokumenty