JANOME Memory Craft 2400 Instrukcja obsługi

2400

INSTRUCTION BOOK

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical appliance, basic safety precautions should always be followed, including the followings:

Read all instructions before using this appliance.

DANGER—To reduce the risk of electric shock:

1. An appliance should never be left unattended when plugged in. Always unplug this sewing machine from the

electric outlet immediately after using and before cleaning.

2. Always unplug before replacing a sewing machine bulb. Replace bulb with same type rated 13.2 Volts D. C.

3 Watts.

WARNING — To reduce the risk of burns, fire, electric shock, or injury to persons:

1. Do not allow to be used as a toy. Close attention is necessary when this sewing machine is used by or near

children.

2. Use this appliance only for its intended use as described in this owner’s manual.

Use only attachments recommended by the manufacturer as contained in this owner’s manual.

3. Never operate this sewing machine if it has a damaged cord or plug, if it is not working properly, if it has

been dropped or damaged, or dropped into water.

Return this sewing machine to the nearest authorized dealers or service center for examination, repair,

electrical or mechanical adjustment.

4. Never operate the appliance with any air opening blocked. Keep ventilation openings of this sewing machine

and foot controller free from accumulation of lint, dust and loose cloth.

5. Never drop or insert any object into any opening.

6. Do not use outdoors.

7. Do not operate where aerosol (spray) products are being used or where oxygen is being administered.

8. To disconnect, turn all controls to the off (“O”) position, then remove plug from outlet.

9. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

10. Keep fingers away from all moving parts. Special care is required around the sewing machine needle.

11. Always use the proper needle plate. The wrong plate can cause the needle to break.

12. Do not use bent needles.

13. Do not pull or push fabric while stitching. It may deflect the needle causing it to break.

14. Switch this sewing machine off (“O”) when making any adjustment in the needle area, such as threading the

needle, changing the needle, threading the bobbin or changing the presser foot, and the like.

15. Always unplug this sewing machine from the electrical outlet when removing covers, lubricating, or when

making any other adjustments mentioned in this owner’s manual.

SAVE THESE INSTRUCTIONS

1

TABLE OF CONTENTS

SECTION IV UTILITY STITCHING

Overcasting ............................................................. 20

• Zigzag Stitch ..................................................... 20

• Overcasting Variations ...................................... 20

Buttonhole .........................................................21-26

• Buttonhole Variations....................................... 21

Sensor Buttonhole ..............................................21-23

• Preparation for Sewing...................................... 21

• To Sew ............................................................. 21

• To Alter Buttonhole Stitch Width and Density ........ 23

• Rounded and Keyhole Buttonholes .................. 24

Automatic Buttonhole (BH 1 )........................... 25

Corded Buttonhole.................................................. 26

Sew a Button ........................................................... 27

Zipper Sewing ....................................................28-29

• To Snap On the Zipper Foot ............................ 28

• Fabric Preparation ............................................ 28

• To Sew ............................................................. 28

Blind Stitch Hemming ............................................ 30

• Changing Needle Position ............................... 30

Rolled Hem ............................................................. 31

SECTION V DECORATIVE STITCHING

Shell Stitch .............................................................. 32

Patchwork ............................................................... 32

Smocking ................................................................ 32

Decorative Stitch ..................................................... 33

Scallop Hems .......................................................... 33

Cording ................................................................... 34

Quilting .................................................................. 35

Adjusting Pattern Balance ....................................... 36

Program Decorative Stitch Patterns ......................... 37

• Combining Patterns.......................................... 37

SECTION VI CARE OF YOUR MACHINE

Care of Your Machine ............................................. 38

Cleaning the Hook Race and Feed Dog .................. 38

Replacing the Bobbin Holder .................................. 38

Troubleshooting ...................................................... 39

SECTION I NAME OF PARTS

Names of Parts .......................................................... 2

Extension Table (Accessory Storage Box) .................. 3

SECTION II GETTING READY TO SEW

Connecting Machine to Power Supply ...................... 4

Controlling Sewing Speed ......................................... 4

Main Function of Keys ........................................... 5-6

Winding the Bobbin .............................................. 7-8

• Set the Spool....................................................... 7

• Removing the Bobbin ......................................... 7

• Winding the Bobbin ........................................... 7

• Inserting the Bobbin ........................................... 8

Threading the machine.........................................9-11

• Threading the machine ....................................... 9

• Needle Threader ............................................... 10

• Drawing Up the Bobbin Thread....................... 11

SECTION III BASIC SEWING

Straight Stitching................................................12-13

• Starting to Sew ................................................. 12

• Changing Sewing Direction .............................. 12

• Finishing Sewing .............................................. 12

• Adjusting Stitch Length Manually .................... 13

• Variable Needle Position .................................. 13

Variation of Straight Stitching ................................. 14

• Straight Stitch ................................................... 14

• Locking Stitch .................................................. 14

• Lock-A-Matic ................................................... 14

• Triple Stretch Stitch ......................................... 14

• Stretch Stitch .................................................... 14

• Saddle Stitch ..................................................... 14

Adjust the Top Thread Tension .............................. 15

• Choose the Correct Tension ............................. 15

• Tension is too tight........................................... 15

• Tension is too loose .......................................... 15

• Seam Allowance Lines....................................... 16

When Sewing Heavy Fabrics ................................... 16

Pressure Adjusting Lever .......................................... 16

To Raise or Drop the Feed Dog .............................. 16

Changing Needles ................................................... 17

To Remove and Attach Presser Foot ........................ 17

To Remove and Attach the Foot Holder ................. 17

Choose Your Needle and Thread ............................ 18

Zigzag Stitch ........................................................... 19

• Manual Stitch Width and Length ..................... 19

2

Names of Parts

q Extension table (Accessory box)

w Needle plate

e Needle threader

r Thread cutter

t Face plate

y Thread take-up lever

u Upper thread guide

i Thread tension dial

o Spool pin

!0 Spool holder

!1 Liquid crystal display

!2 Function keys

!3 Screen sharpness adjusting knob

!4 Reverse button

!5 Feed balancing dial

!6 Hook cover plate release button

!7 Foot holder

!8 Presser foot

!9 Needle clamp screw

@0 Needle

@1 Machine sockets

@2 Power switch

@3 Balance wheel

@4 Bobbin winder stopper

@5 Bobbin winder spindle

@6 Carrying handle

@7 Hole for additional spool pin

@8 Presser foot lifter

@9 Buttonhole lever

#0 Free arm

#1 Drop feed lever

q

w

e

r

t

io

!0 !1

!3

!4

!5

!6

!8

@5

#1

!9

@0

!7

uy

!2

@8

@4 @6 @7

@9

#0

@1

@2

@3

SECTION I NAME OF PARTS

3

qw e r

t

yu

i

Extension Table (Accessory Storage Box)

q Bobbin

w G: Blind hem stitch foot

e H: Cording foot

r A: Zigzag foot

t E: Zipper foot

y C: Overedge foot

u D: Hemmer foot

i F: Satin stitch foot

o Extension Table

z Pull the end of the extension table away from the machine,

as illustrated.

x The lid of the accessory storage box lifts open toward

you.

Sewing accessories are conveniently located in the box.

!0 Screwdriver

!1 R: Automatic buttonhole foot

!2 Lint brush

!3 Set of needles

!4 Seam ripper

!5 Large spool holder

!6 Small spool holder

!7 Spool stand

!8 Additional spool pin

!9 Quilter

@0 Spool pin felt

!0

!1

!2

!3

!4

G

A

E

C

D

F

H

o

z

x

!6

!7

!8

!9

!5

@0

4

Connecting Machine to Power Supply

Before connecting the power cord, make sure the voltage

and frequency shown on the machine conform to your

electrical power.

For Use of the Foot Control:

* Turn off the power switch, and insert the foot

control plug q and the machine plug w into the

machine and the power supply plug e into the

wall, in this order.

q Foot control plug

w Machine plug

e Power supply plug

r Power switch

t Power supply cord

y Foot control

For Your Safety:

1. While in operation, always keep your eye on the

sewing area, and do not touch any moving parts such

as the thread take-up lever, handwheel or needle.

2. Always turn off the power switch and unplug from the

power supply:

* When leaving the machine unattended.

* When attaching or removing parts.

* When cleaning the machine.

3. Do not place anything on the foot control, except in use.

Operating Instructions:

The symbol “0”of a switch indicates the “off ” position

of a switch.

For appliances with a polarized plug (one blade wider

than the other ).

To reduce the risk of electric shock, this plug is intended

to fit in a polarized outlet only one way. If the plug does

not fit fully in the outlet, reverse the plug. If it still does

not fit, contact a qualified electrician to install the proper

outlet. Do not modify the plug in any way.

Foot Controller Model 21249 use with Sewing Machine

Model MC 2400.

(For U.S.A. market only).

Controlling Sewing Speed

Sewing speed can be varied by the foot control.

The harder you press on the foot control, the faster the

machine runs.

q

w

e

r

t

y

SECTION II GETTING READY TO SEW

5

Main Function of Keys

q Reverse Button

During straight stitching , zigzag stitching and multiple zigzag stitching ,

press and hold the reverse button. The machine will sew in reverse until you release

the button.

During utility stitching and decorative stitching, press this button and the machine

will sew an auto-lock stitch and stop automatically.

w Auto-Lock Key

During straight stitching , zigzag stitching and multiple zigzag stitching :

The machine will take a few stitches in place and stop automatically.

During utility stitching and decorative stitching:

Press this key when running the machine to sew an auto-lock stitch at the end of

pattern and stop automatically.

e Up/Down Needle Position Key

When you press this key, the needle will go up or down.

If the needle is up and you press this key, the needle will go down to its lowest

position.

If the needle is down and you press this key, the needle will go to its highest position.

r Screen Sharpness Adjusting Dial

Sharpness of liquid crystal will change.

* Turn the screen sharpness adjusting dial if LCD screen is not clear (or completely

dark), when turning on the power switch.

t Stitch Width Control Key

Stitch width and stitch length will show on the liquid crystal display.

* To decrease the stitch width, press the “ ” key .

The stitch width will decrease.

* To increase the stitch width, press the “ + ” key .

The stitch width will increase.

q

w

rty u

i

o

q

w

e

r

t

e

6

y

u

i

o

y Stitch Length Control Key

Stitch width and stitch length will show on the display.

To decrease the stitch length, press the “–” key.

The stitch length will decrease. To increase the stitch length, press the “+” key.

The stitch length will increase.

u Memory Key

When this key is pressed after selecting a pattern, the pattern will be memorized as

many times as the key is pressed. When the key is pressed after selecting another pattern,

that pattern will be memorized after the previously memorized pattern.

(Up to 50 patterns, including the locking stitch at the end, can be programmed in the

memory.)

i Clear Key

When this key is pressed before starting sewing, the memorized characters can be cleared

one by one.

When the key is pressed after starting sewing, the entire memorized program is cleared.

o Pattern Selection Keys

You can select these patterns by pressing the pattern

selection keys.

1. Display when the power switch is turned on and

Pattern 01 is selected.

2. Display when a pattern is selected, (Example:

Pattern 19.)

3. Pattern number and pattern

4. Recommended Foot

5. Suitable thread tension

1

2

3

4

M

C

01

A

26

5

7

Winding the Bobbin

• Set the Spool

Lift up the spool pin and place the spool of thread on it

with the thread coming off the spool as shown.

Press the large spool holder firmly against the spool of

thread.

* The small spool holder is used with small or

narrow spools of thread.

q

Spool pin

w Ordinary spool

e Large spool holder

r Small spool holder

t Small spool

• Removing the Bobbin

Gently slide the hook cover plate release button to the

right and remove the cover plate.

Lift out the bobbin.

q

Hook cover plate release button

w Hook cover plate

• Winding the Bobbin

z Guide the thread around the thread guide.

x Thread through the hole in the bobbin from the inside

to the outside.

* The additional spool pin is used to wind an extra

bobbin without unthreading the machine. To use,

insert the spool stand and the additional spool pin

in the hole. Place the felt and spool on the pin with

the thread coming off the spool as shown.

er

q

w

t

q Hole for additional spool pin

w Spool stand

e Additional spool pin

r Felt

t Spool

c Put the bobbin on the bobbin winder spindle and

push it to the right. With the free end of the thread

held in your hand, depress the foot control. Stop the

machine when it has made a few turns, and cut the

thread close to the hole in the bobbin.

y

Bobbin winder stopper

v Depress the foot control again. When the bobbin is

fully wound, it will stop automatically.

b Return the bobbin winder to its original position by

moving the spindle to the left, and cut the thread as

shown.

y

c

vb

q

w

e

r

t

z

x

w

8

• Inserting the Bobbin

z Place the bobbin in the bobbin holder with the thread

running counterclockwise.

x Guide the thread into notch A on the front side of the

bobbin holder.

Draw the thread to the left, sliding it between the

tension spring blade.

Continue to draw the thread lightly until the thread

slips into notch B.

Pull out about 15 cm (6") of thread.

c Attach the hook cover plate.

Check the threading by referring to the chart shown on

the hook cover plate.

q

Bobbin thread

B

z

x

c

A

q

9

q

e

r

y

u

Threading the Machine

• Threading the Machine

* Raise the presser foot lifter.

* Press the up/down needle position key twice to

raise the needle.

q

Up/down needle position key

w Presser foot lifter

z Draw the thread around the upper thread guide.

e

Upper thread guide

x Then, down around the check spring holder.

r

Check spring holder

c Firmly draw the thread from right to left over the

take-up lever and down into the take-up lever eye.

t

Thread take-up lever

v Then, down through the lower thread guide.

y

Lower thread guide

b Slide the thread behind the needle bar thread guide on

the left.

Thread the needle from front to back or use the needle

threader.

u

Needle bar thread guide

w

e

t

r

y

u

z

x

c

vb

t

10

qw

• Needle Threader

z Raise the needle to its highest position. Pull down the

needle threader knob as far as it will go.

x Turn the knob in the direction of the arrow in the

illustration, then insert Hook q into the needle eye.

Lead the thread around Guide w and under Hook q.

q

Hook

w Guide

c Turn the knob in the direction of the arrow in the

illustration, drawing the thread loop through the

needle.

v Pull the thread through the needle eye.

The needle threader can be used with a #11 to #16

needle or a blue tipped needle. Thread size 50 to 100

should also work well.

cv

x

z

11

• Drawing Up the Bobbin Thread

¡ Raise the presser foot. Hold the needle thread lightly

with your left hand.

™ Press the up/down needle position key twice to pick up

the bobbin thread. Draw up the needle thread together

with a loop of bobbin thread.

q

Up/down needle position key

£ Pull 10 cm (4" ) of both threads to the back under the

presser foot.

q

™

¡

£

12

Straight Stitching

q Selected stitch

w A: Zigzag foot

• Starting to Sew

Raise the presser foot and position the fabric next to a seam

guide line on the needle plate (see page 16). Lower the

needle to the point where you want to start. Lower the

presser foot and pull the threads toward the back. Depress

the foot control. Gently guide the fabric along a seam

guide line letting the fabric feed naturally.

• Changing Sewing Direction

Stop the machine and bring the needle down into the

fabric by pressing the up/down needle position key.

Raise the presser foot.

Pivot the fabric around the needle to change sewing

direction as desired. Lower the presser foot.

q

Up/down needle position key

w Presser foot lifter

• Finishing Sewing

To fasten the ends of seams, press the reverse button and

sew several reverse stitches.

* When pattern is selected, reverse stitches are

sewn automatically at the beginning of the seam,

and forward again.

Raise the presser foot. Remove the fabric, draw the threads

to the back and cut using the thread cutter.

The threads are cut the proper length for starting the next

seam.

q

Reverse button

w Thread cutter

e Fabric

q

w

q

w

e

01

A

26

q

w

SECTION III BASIC SEWING

13

• Adjusting Stitch Length Manually

When you press the stitch length key , the

pre-programmed setting (2.2) will appear on the screen.

It can be set between 0 and 5.

Press the minus mark and the number on the screen

will get smaller, and the stitch length will get shorter.

Press the plus mark and the number on the screen

will get bigger, and the stitch length will get longer.

* The reverse stitch length cannot be set longer than

2.5 mm (3/32" ).

• Variable Needle Position

When the patterns listed listed below (left) are selected and

the needle position key is pressed, you can move the

needle to any position desired.

q

Left

w Middle

e Right

01

W

3.5

L

2.2

01

W

3.5

L

2.2

L 1.0 L 2.2 L 5.0

qw e

W 0.0 W 3.5

W 7.0

01

A

26

14

Variation of Straight Stitching

• Straight Stitch

When the machine is turned on, it’s automatically set to

sew a straight stitch.

This stitch can be used for regular seams, zippers,

topstitching, etc.

q

Selected stitch w A: Zigzag foot

• Locking Stitch

Lower the needle close to the front edge of the fabric. The

machine will sew several locking stitches in place and

continue sewing forward. If you press the reverse button at

the end of the seam, the machine will sew several locking

stitches in place, then stop sewing automatically.

• Lock-A-Matic

The machine will sew four stitches forward, four stitches in

reverse, then continue sewing forward.

When you reach the end edge of the fabric, press the

reverse button once.

The machine will sew four reverse stitches, four forward

stitches, then stop sewing.

• Triple Stretch Stitch

This strong, durable stitch is recommended where both

elasticity and strength are needed to insure comfort and

durability.

Use it to reinforce areas such as crotch and armhole seams.

Also use when constructing items such as backpacks for

extra strength.

• Stretch Stitch

This stitch is a narrow stretch stitch designed to eliminate

puckering on knit fabrics and bias seams, while permitting

the seam to be pressed completely flat. The stitch can also

be used to simultaneously seam and overcast when sewing

on tricot and chiffons for a narrow, almost invisible seam

or seam finish.

• Saddle Stitch

For topstitching suits, blazers, jumpers and denim outfits.

q

w

15

Adjust the Top Thread Tension

• Choose the Correct Tension

For Straight Stitch:

The ideal straight stitch will have threads locked between

the two layers of fabric, as shown left (magnified to show

detail).

If you look at the top and bottom of the seam, you will

notice that there are no gaps; that each stitch is smooth

and even.

When adjusting top thread tension, the higher the

number, the tighter the top thread.

Results depend on;

* stiffness and thickness of the fabric

* number of fabric layers

* type of stitch

q

Needle thread (Top thread)

w Bobbin thread (Bottom thread)

e Right side of fabric

r Wrong side of fabric

t To loosen

y To tighten

• Tension is too tight

The bobbin thread shows through on the right side of the

fabric and it will feel bumpy.

Turn the dial to the left to loosen the top thread tension.

q

Right side of fabric

w Wrong side of fabric

e To loosen

• Tension is too loose

The top thread shows through on the wrong side of the

fabric and it will feel bumpy.

Turn the dial to the right to tighten the top thread tension.

q

Right side of fabric

w Wrong side of fabric

e To tighten

qw

q

e

w

q

y

t

w

e

r

4

3

5

4

3

5

4

3

5

16

• Seam Allowance Lines

The seam guides on the needle plate and hook cover plate

help you measure seam width.

* The number indicates the distance between the

middle needle position and the seam

allowance line.

Marks on

needle plate

Millimeters Inches

15

20 4/8" 5/8" 6/8"

q Middle needle position

w Edge of fabric

e Needle plate guide lines

When Sewing Heavy Fabrics

The presser foot lifter raises and lowers the presser foot.

You can raise it about 0.7 cm (1/4" ) higher than the

normal up position for easy removal of the presser foot or

to help you place heavy fabrics under the presser foot.

q

Presser foot lifter

Pressure Adjusting Lever

The pressure adjusting lever should be set at “3” for regular

sewing.

Reduce the pressure to “2” for cut work, drawn work,

basting and embroidery.

Set the pressure to “1” when sewing chiffon, lace, organdy

and other fine fabrics.

Velours and knits with a lot of stretch may also require a

“1” setting.

q

Pressure adjusting lever

To Raise or Drop the Feed Dog

For button sewing, etc. drop the feed dog.

After finished sewing, raise the feed dog.

The feed dog must always be up for normal sewing.

q

Lowered position

w Raised position

q

w

e

q

w

15

20

5/8

6/8

17

Changing Needles

z Raise the needle by pressing the up/down needle

position key and lower the presser foot.

Turn off the power switch.

Loosen the needle clamp screw by turning it

counterclockwise.

x Remove the needle from the clamp.

Insert the new needle into the needle clamp with the

flat side to the rear.

When inserting the needle into the clamp, push it up

as far as it will go and tighten the clamp screw firmly.

c To find a good needle, put the flat side of the needle

onto something flat (a needle plate, glass, etc.).

The gap between the needle and the flat surface should

be consistent. Never use a bent or blunt needle.

q

Needle clamp screw

w Pin

e Needle clamp

To Remove and Attach Presser Foot

Press the red button on the back of the foot holder.

The presser foot will drop off. Place the selected presser

foot so the pin on the foot lies just under the groove of the

foot holder.

Lower the presser bar to lock the foot in place.

q

Red button

w Groove

e Pin

To Remove and Attach the Foot Holder

z To Remove:

Remove the thumb screw by turning the screw

counter-clockwise with the screwdriver.

q

Thumb screw

x To Attach:

Match the hole in foot holder with the threaded

hole in the presser bar.

Fit the thumb screw into the hole.

Tighten the screw by turning it clockwise.

w

Foot holder

e Presser bar

x

z

q

e

q

w

e

w

zx

q

w

e

c

18

Choose Your Needle and Thread

NEEDLE SIZE

9 or 11

11 or 14

14 or 16

THREADS

Fine Silk

Fine Cotton

Fine Synthetic

Fine Cotton-covered

Polyester

50 Silk

50 to 80 Cotton

50 to 60 Synthetic

Cotton-covered

Polyester

50 Silk

40 to 50 Cotton

40 to 50 Synthetic

Cotton-covered

Polyester

FABRICS

Crepe de Chine,

Voile, Lawn,

Organdy,

Georgette,Tricot

Linens, Cotton,

Pique, Serge,

Double Knits,

Percale

Denim, tweed,

Gabardine, Coating,

Drapery, and

Upholstery Fabric

LIGHT WEIGHT

MEDIUM WEIGHT

HEAVY WEIGHT

NOTE:

In general, fine threads and needles are used for sewing thin fabrics, and thicker threads and needles and used for sewing heavy

fabrics.

Always test thread and needle size on a small piece of fabric which will be used for actual sewing.

Use the same thread for needle and bobbin.

When sewing stretch, very fine fabrics and synthetics, use a blue tipped needle. The blue tipped needle effectively prevents

skipped stitches.

Strona jest ładowana ...

JANOME Memory Craft 2400 Instrukcja obsługi

JANOME Memory Craft 2400 Instrukcja obsługi

w innych językach

Powiązane dokumenty

Inne dokumenty