JANOME Elna Lotus Instrukcja obsługi

JanomeFlyer.com

Elna Lotus

Instruction Manual

Elna Lotus Sewing Machine Instruction Manual

www.janomeflyer.com

Lotus Owners Manual/ User Guide

JanomeFlyer.com

IMPORTANT SAFETY INSTRUCTIONS

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning

use of the appliance by a person responsible for their safety.

Children should be supervised to ensure that they do not play with the appliance.

When using an electrical appliance, basic safety precautions should always be followed, including the

following:

This sewing machine is designed and manufactured for household use only.

Read all instructions before using this sewing machine.

Please note that on disposal, this product must be safely recycled in accordance with relevant National legislation relating to

electrical/electronic products. If in doubt please contact your retailer for guidance. (European Union only)

DANGER

—

To reduce the risk of electric shock:

An appliance should never be left unattended when plugged in. Always unplug this sewing machine from the

electric outlet immediately after using and before cleaning.

WARNING

—

To reduce the risk of burns, ﬁre, electric shock, or injury to persons:

1. Do not allow to be used as a toy. Close attention is necessary when this sewing machine is used by or near

children.

2. Use this appliance only for its intended use as described in this owner’s manual.

Use only attachments recommended by the manufacturer as contained in this owner’s manual.

3. Never operate this sewing machine if it has a damaged cord or plug, if it is not working properly, if it has been

dropped or damaged, or dropped into water.

Return this sewing machine to the nearest authorized dealer or service center for examination, repair, electrical or

mechanical adjustment.

4. Never operate the appliance with any air opening blocked. Keep ventilation openings of this sewing machine and

foot controller free from accumulation of lint, dust and loose cloth.

5. Never drop or insert any object into any opening.

6. Do not use outdoors.

7. Do not operate where aerosol (spray) products are being used or where oxygen is being administered.

8. To disconnect, turn all controls to the off (“O”) position, then remove plug from outlet.

9. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

10. Keep ﬁngers away from all moving parts. Special care is required around the sewing machine needle.

11. Always use the proper needle plate. The wrong plate can cause the needle to break.

12. Do not use bent needles.

13. Do not pull or push fabric while stitching. It may deﬂect the needle causing it to break.

14. Switch this sewing machine off (“O”) when making any adjustment in the needle area, such as threading the

needle, changing the needle, threading the bobbin or changing the presser foot, and the like.

15. Always unplug this sewing machine from the electrical outlet when removing covers, lubricating, or when making

any other adjustments mentioned in this owner’s manual.

SAVE THESE INSTRUCTIONS

Elna Lotus Sewing Machine Instruction Manual

www.janomeflyer.com

Lotus Owners Manual/ User Guide

JanomeFlyer.com

Table of Contents

SECTION I. NAMES OF PARTS

Names of Parts ........................................................... 2-3

Standard Accessories ................................................... 3

Accessory Storages ...................................................... 4

Protection Flaps ............................................................ 5

SECTION II. GETTING READY TO SEW

Connecting the Power Supply ....................................... 6

Before Using Your Sewing Machine .............................. 6

Operating Instructions ................................................... 6

Presser Foot Lifter ......................................................... 7

Changing the Presser Foot ........................................... 7

Removing and Attaching the Foot Holder ..................... 7

Changing the Needle ..................................................... 8

Selecting Thread and Needles ...................................... 8

Needle Deﬁnitions ......................................................... 9

Machine Operating Buttons .......................................... 10

Pattern Selection ......................................................... 11

LCD Display ..................................................................11

Speed Control Slider ....................................................11

Controlling Sewing Speed ............................................11

Bobbin Winding ....................................................... 12-14

Threading the Machine ............................................15-17

Adjusting the Needle Thread Tension ..........................18

Dropping or Raising the Feed Dog ............................... 19

Correcting Distorted Stretch Stitch Patterns ................19

Setting Mode .......................................................... 20-21

SECTION III. BASIC SEWING

Straight Stitch Sewing ............................................ 22-23

Lock-a-Matic Stitch .......................................................24

Triple Stretch Stitch ......................................................24

Stretch Stitch ................................................................24

Zigzag Stitch ................................................................ 25

Multiple Zigzag ............................................................ 25

Super Stretch Stitch .................................................... 26

Super Overlock Stitch ................................................. 26

Overedge Stitch........................................................... 26

Zipper Sewing .........................................................27-28

Rolled Hem .................................................................. 29

Pintuckis ...................................................................... 30

Gathering ..................................................................... 30

Button Sewing ..............................................................31

Blind Hem .................................................................... 32

Applique ...................................................................... 33

Fringing ........................................................................ 33

Sculpture Stitch ........................................................... 34

Patchwork .................................................................... 34

Bridging (Fagoting) ...................................................... 35

Attaching Elastic .......................................................... 35

Scallop edges .............................................................. 35

Various Kinds of Buttonholes and Their Uses ............. 36

Classic Square Buttonhole .....................................36-38

Adjusting the Stitch Width and Density for

Buttonholes ................................................................. 39

Corded Buttonhole ...................................................... 40

Classic Keyhole Buttonhole ......................................... 40

Darning Stitch ............................................................... 41

SECTION IV CARE OF YOUR MACHINE

Cleaning the Hook Race, Feed Dog and the Thread

Cutter Mechanism ....................................................... 42

Installing the Bobbin Holder ........................................ 42

Problems and Warning Signs ...................................... 43

Troubleshooting ........................................................... 44

Elna Lotus Sewing Machine Instruction Manual

www.janomeflyer.com

Lotus Owners Manual/ User Guide

JanomeFlyer.com

2

SECTION I. NAMES OF PARTS

Names of Parts

q LCD screen

w Stitch width adjusting buttons

e Stitch length adjusting buttons

r Start/stop button

t Reverse stitch button

y Auto-lock button

u Needle up/down button

i Thread cutter button

o Speed control slider

!0 Touch panel

!1 Thread tension dial

!2 Accessory drawer

!3 Protection ﬂaps unlock button

!4 Protection ﬂaps release lever

!5 Bobbin winder stopper

!6 Bobbin winder spindle

!7 Accessory storage

!8 Stitch reference chart

!9 Thread take-up lever

@0 Thread guide (B)

@1 Bobbin winder thread guide (B)

@2 Bobbin winder thread guide (A)

@3 Retractable thread guide

@4 Threading chart

@5 Top cover

@6 Thread guide (A)

@7 Spool pin

@8 Spool thread guide

@9 Protection ﬂaps

#0 Needle thread guide

#1 Needle cramp screw

#2 Needle

#3 Presser foot

#4 Hook cover release button

#5 Hook cover plate

#6 Needle plate

#7 Feed dog

#8 Foot holder

#9 Needle threader

$0 Buttonhole lever

r t

y

u

!3

i

!1

o

!4

!5

!0

!6

!7

!8

!9

@0

@1

@2

@3

@4

@5

@6

@7

@8

@9

q w e

!2

#0

#1

#2

#3

#4

#5

#6

#7

#8

#9

$0

Elna Lotus Sewing Machine Instruction Manual

www.janomeflyer.com

Lotus Owners Manual/ User Guide

JanomeFlyer.com

3

NOTE:

Sewing machine design and speciﬁcations are subject

to change without prior notice.

$1

$2

$3

$4

$5

$6

$7

$8

$9

%0

%1

$1 Feed adjusting screw

$2 Drop feed lever

$3 Carrying handle

$4 Handwheel

$5 Power switch

$6 Foot control jack

$7 Machine inlet

$8 Presser foot lifter

$9 Thread cutter

%0 Foot control

%1 Power supply cable

Standard Accessories

q

Zigzag foot:

A (set on the machine)

w

Zipper foot: E

e

Blind hem foot: G

r

Satin stitch foot: F

t

Rolled hem foot: D

y

Automatic buttonhole foot: R

u

Spool holder (large) (set on the machine)

i

Spool holder (small)

o

Bobbins ( X 4) (1 set on the machine)

!0

Assorted needle set

!1

Lint brush

!2

Seam ripper (Buttonhole opener)

!3

Screwdriver

!4

Instruction book

q w e r

t y u i

o !0 !1 !2

!3 !4

Elna Lotus Sewing Machine Instruction Manual

www.janomeflyer.com

Lotus Owners Manual/ User Guide

JanomeFlyer.com

4

Accessory Storages

Accessories can be stored in the accessory storage

and the accessory drawer.

Open the top cover to access the accessory storage.

Open the protection ﬂap (front) and pull the tab on the

right side of the ﬂap to open the accessory drawer.

Elna Lotus Sewing Machine Instruction Manual

www.janomeflyer.com

Lotus Owners Manual/ User Guide

JanomeFlyer.com

5

Protection Flaps

•Openingandclosingprotectionaps

To open the protection ﬂaps, slide the protection ﬂap

release lever q to the right.

To close the protection ﬂaps, fold the rear and front

ﬂaps w e, then fold the left ﬂap r until it snaps to

the both ﬂaps.

q Protection ﬂaps release lever

w Protection ﬂap (front)

e Protection ﬂap (rear)

r Protection ﬂap (left)

q

w

e

r

•Detachingtheprotectionaps

To detach the protection ﬂaps, push down the

protection ﬂap unlock button, and pull the protection

ﬂaps away from the machine as illustrated.

t Protection ﬂaps unlock button

•Attachingtheprotectionaps

To attach the protection ﬂaps, push the protection

ﬂaps, inserting the hook into the hole until it snaps into

the machine.

•Free-armsewing

Free-arm sewing is useful for darning socks and

mending the knee or cuff areas.

t

Elna Lotus Sewing Machine Instruction Manual

www.janomeflyer.com

Lotus Owners Manual/ User Guide

JanomeFlyer.com

6

WARNING:

While in operation, always keep your eyes on the

sewing area and do not touch any moving parts

such as the thread take-up lever, handwheel or

needle.

Always turn off the power switch and unplug from

the power supply:

- when leaving the machine unattended.

- when attaching or removing parts.

- when cleaning the machine.

Do not place anything on the foot control, otherwise

the machine will run inadvertently.

SECTION II. GETTING READY TO SEW

ConnectingthePowerSupply

•Usingthefootcontrol

Turn off the power switch q.

Pull the foot control cord from the foot control.

Insert the foot control plug w into the foot control jack e.

Insert the machine plug r into the machine inlet t.

Insert the power supply plug y into the wall outlet u.

Turn on the power switch q.

The foot control sign i will be displayed when the foot

control is connected to the machine.

q Power switch

w Foot control plug

e Foot control jack

r Machine plug

t Machine inlet

y Power supply plug

u Wall outlet

i Foot control sign

•Usingthestart/stopbutton

Turn off the power switch q.

Insert the machine plug w into the machine inlet e.

Insert the power supply plug r into the wall outlet t.

Turn on the power switch q.

q Power switch

w Machine plug

e Machine inlet

r Power supply plug

t Wall outlet

NOTES:

•Themachinewillbeinitializedwhenturningonthe

power switch. Do not touch the machine while the

machine is being initialized.

•Thestart/stopbuttondoesnotworkwhenthefoot

control is connected.

BeforeUsingYourSewingMachine

Before using your sewing machine for the ﬁrst time,

place a scrap of fabric under the presser foot and run the

machine without thread for a few minutes. Wipe away

any oil which may appear.

OperatingInstructions:

The symbol “O” on a switch indicates the “off” position

of a switch.

For appliances with a polarized plug (one blade wider

than the other): To reduce the risk of electric shock, this

plug is intended to ﬁt in a polarized outlet only one way.

If it still does not ﬁt, contact a qualiﬁed electrician to

install the proper outlet. Do not modify the plug in any

way (U.S.A. and Canada only).

* Foot control model 21371 is used with this sewing

machine.

q

w

e

t

u

y

r

i

q

e

t

r

w

NOTE:

Do not pull the cord of foot control beyond the red

marker on the cord.

Elna Lotus Sewing Machine Instruction Manual

www.janomeflyer.com

Lotus Owners Manual/ User Guide

JanomeFlyer.com

7

ChangingthePresserFoot

CAUTION:

Turn OFF the power switch before changing the foot.

Always use the proper foot for the selected pattern.

The wrong foot can cause the needle to break.

•Removingthepresserfoot

Raise the needle to its highest position by turning the

handwheel counterclockwise. Raise the presser foot,

and press the lever q on the back of the foot holder.

•Attachingthepresserfoot

Place the selected presser foot so that the pin e on

the foot lies just under the groove w in the foot holder.

Lower the presser bar to lock the foot into the place.

q Lever

w Groove

e Pin

RemovingandAttachingtheFootHolder

•Removingthefootholder

Remove the thumbscrew q by turning it

counterclockwise with a screwdriver.

•Attachingthefootholder

Align the hole in the foot holder w with the threaded

hole in the presser bar e. Fit the thumbscrew q

into the hole. Tighten the thumbscrew q by turning it

clockwise with a screwdriver.

q Thumbscrew

w Foot holder

e Presser bar

CAUTION:

Turn OFF the power switch before detaching or

attaching foot holder.

q

w

e

q

w

e

Presser Foot Lifter

The presser foot lifter q raises and lowers the presser foot.

You can raise the foot about 1/4˝ (0.6 cm) higher than the

normal up position w for easy removal of the presser foot,

or to help you place thick material under the foot.

q Presser foot lifter

w Normal up position

e Highest position

q

w

e

q

we

Elna Lotus Sewing Machine Instruction Manual

www.janomeflyer.com

Lotus Owners Manual/ User Guide

JanomeFlyer.com

8

ChangingtheNeedle

z Turn off the power switch.

Raise the needle to its highest position by turning

the handwheel counterclockwise, and lower the

presser foot. Loosen the needle clamp screw q by

turning it counterclockwise. Remove the needle from

the needle clamp w.

x Insert a new needle into the needle clamp w with

the ﬂat side to the rear. When inserting the needle

into the needle clamp w, push it up as far as it will

go. Tighten the needle clamp screw q ﬁrmly by

turning it clockwise.

c To see if the needle is in good condition, place the

ﬂat side of the needle onto something ﬂat (needle

plate, glass, etc.). The gap between the needle and

the ﬂat surface should be consistent. Never use a

bent or blunt needle.

A damaged needle can cause permanent snags or

runs in knits, ﬁne silks and silk-like fabrics.

q Needle clamp screw

w Needle clamp

CAUTION:

Turn OFF the power switch before changing the

needle.

Fabric

Light

Thread

Medium

Heavy

Lawn

Georgette

Tricot

Wool,

Polyester

Cotton,

Polyester

Fine jersey

Wool

Denim

Jersey

Coating

Quilting

Silk #80-100

Cotton #80-100

Synthetic #80-100

Silk #50

Cotton #60-80

Synthetic #50-80

Cotton #50

Silk #50

Cotton #40-50

Synthetic #40-50

Silk #30

Cotton #50

#9/65–11/75

#11/75–14/90

#14/90

#14/90–16/100

#16/100

SelectingThreadandNeedles

For general sewing, use needle size 11/75 or 14/90.

A ﬁne thread and needle should be used for sewing

lightweight fabrics, so the fabric will not be marred.

Heavy fabrics require a needle large enough to pierce

the fabric without fraying the needle thread.

Always test the needle size on a small scrap of the

fabric that will be used for actual sewing.

In general, use the same thread for the needle and

bobbin. When sewing stretch fabrics, very ﬁne fabrics

and synthetics, use a BLUE TIPPED needle. The blue

tipped needle effectively prevents skipped stitches.

Needle

q w

Elna Lotus Sewing Machine Instruction Manual

www.janomeflyer.com

Lotus Owners Manual/ User Guide

JanomeFlyer.com

9

q

w

e

r

t

y

A

B

C

D

E

F

Needle Deﬁnitions

The illustration identiﬁes the main parts of a

sewing machine needle.

q

Body

w

Shaft

e

Long groove (round side of needle)

r

Short groove (ﬂat side of needle)

t

Eye

y

Point

A:Universal

– an all-purpose needle that handles

most

woven and knit fabrics.

B: Ball point

– the point spreads the ﬁbers,

preventing

tears and is especially suited for loose knits and interlock

knits. Not recommended for embroidery.

C: Denim

– the sharp point effectively pierces densely

woven fabrics such as denim and canvas.

D:Stretch

– specially designed to prevent skipped stitch-

es in synthetic suedes and elasticized knits (swimwear).

E:Leather

– the cutting point creates small holes in

leather and suede. Holes remain after stitching is re-

moved.

F:Topstitching

– the extra sharp point penetrates layers

of fabrics; extra large eye and large groove accommodate

heavyweight topstitching thread.

Elna Lotus Sewing Machine Instruction Manual

www.janomeflyer.com

Lotus Owners Manual/ User Guide

JanomeFlyer.com

10

w Reversestitchbutton

When stitches (01, 05, 06) are selected, the

machine will sew in reverse while the reverse stitch

button is pressed.

If you press the reverse stitch button when stitch

pattern 01, 05 or 06 is selected and the foot control

is not connected, the machine will sew in reverse as

long as the button is pressed, and the machine will

stop when the button is released.

If you press the reverse stitch button when sewing any

other stitches except (02, 18), the machine will

immediately sew locking stitches and automatically

stop.

e Auto-lockbutton

When stitches (01, 05, 06) are selected, the

machine will sew immediately sew locking stitches

and automatically stop when the auto-lock button is

pressed.

If you press the auto-lock button when sewing any

other stitches, the machine will sew locking stitches at

the end of the current pattern and automatically stop.

r Needleup/downbutton

Press this button to bring the needle up or down.

The machine will stop with the needle up or down

depending on the machine setting (see page 20).

t ThreadCutterButton

Press this button to trim the threads after sewing.

The thread cutter sign will blink y while the machine

cuts the threads.

You can continue sewing without pulling the bobbin

thread up after trimming the threads.

To trim the threads automatically after the sewing,

select the desired stitch pattern, then press and hold

the thread cutter button until the thread cutter sign

appears u.

The machine will automatically stop and trim the

threads after locking stitches when the reverse or

auto-lock button is pressed.

* To cancel the auto-thread cutting, press and hold

the thread cutter button until the thread cutter sign

disappears.

NOTE:

Use the thread cutter on the face cover if the thread

is #30 or thicker.

MachineOperatingButtons

q Start/Stopbutton

Lower the presser foot lifter.

Press the start/stop button q to start the machine.

The machine starts running slowly for the ﬁrst few

stitches; it then runs at the speed set by the speed

control slider.

Press the start/stop button q again to stop the

machine.

NOTES:

•Themachinerunsslowlyaslongasyoupressand

hold the start/stop button q.

•Thestart/stopbuttonq cannot be used when the

foot control is connected to the machine.

q

w

e

r t

y

u

Elna Lotus Sewing Machine Instruction Manual

www.janomeflyer.com

Lotus Owners Manual/ User Guide

JanomeFlyer.com

11

i Stitchwidthadjustingbutton

Press “ ” or “ ” to change the stitch width or needle

drop position (see pages 23 and 25).

The indicator !0 will show the stitch width or needle

drop position.

o Stitchlengthadjustingbutton

Press “ ” or “ ” to change the stitch length (see

pages 23 and 25).

The indicator !1 will show the stitch length.

i o

!0 !1

Speed Control Slider

Sewing speed can be varied by the speed control slider

according to your sewing needs.

To increase sewing speed, slide the slider to the right.

To decrease sewing speed, slide the slider to the left.

ControllingSewingSpeed

Depress the foot control to start the machine.

The further down you press on the foot control, the

faster the machine runs.

The maximum sewing speed can be varied by the

speed control slider.

Pattern Selection

You can select stitch patterns directly by pressing the

pattern keys on the touch panel.

LCD Display

The LCD display shows the following information when

the machine is turned on:

q Stitch pattern number

w Type of presser foot

e Stitch width

r Stitch length

q e

r

w

Elna Lotus Sewing Machine Instruction Manual

www.janomeflyer.com

Lotus Owners Manual/ User Guide

JanomeFlyer.com

12

•Settingthespool

z Turn the spool thread guide e as illustrated, and

the spool pin r will lift up.

WARNING

Do not lean over the top of spool pin when turning the

spool guide. The spool pin pops up and it may strike

your face.

e Spool thread guide

r Spool pin

Bobbin Winding

•Removingthebobbin

Gently slide the hook cover release button q to the　

right and remove the hook cover plate w.

Lift out the bobbin.

q Hook cover release button

w Hook cover plate

q

w

e

r

t

u

x

c

z

t

r

x Place a spool of thread on the spool pin with the

thread running off counterclockwise.

Draw the thread from the spool about 4˝ (10 cm) of

thread. Attach the large spool holder t.

t Large spool holder

y Slit

c Press the spool holder t ﬁrmly against the spool

of thread, and then push down the spool pin r to

lower the spool until it is locked in the bottom.

* The small spool holder u is used with narrow or

small spools of thread.

u Small spool holder

NOTE:

If a rimless spool may not let thread out smoothly,

place the spool on the spool pin in up position and do

not use the spool holder so the spool can rotate freely.

NOTE:

If there is a slit y on the spool of thread, be sure to

place the spool with the slit end up.

y

Elna Lotus Sewing Machine Instruction Manual

www.janomeflyer.com

Lotus Owners Manual/ User Guide

JanomeFlyer.com

13

•Bobbinwinding

NOTES:

•Setthespeedcontrolslideratitsfastestposition

for bobbin winding.

•Closetheretractablethreadguideafterthebobbin

winding.

z Turn the spool guide as illustrated.

Draw the thread from the spool and pass it through

the spool guide.

x Pass the thread through the thread guide (A).

c Raise the retractable thread guide.

Guide the thread around the bobbin winder thread

guide (A) q and (B) w as illustrated.

v Pass the thread through the hole in the top of the

bobbin from the inside to outside.

b Put the bobbin on the bobbin winder spindle.

n Push the bobbin to the right. The bobbin mark e

appears on the LCD display.

m With the free end of the thread held in your hand,

start the machine. Stop the machine when bobbin

has wound a few layers, and then cut the thread

close to the hole in the bobbin.

, Start the machine again. When the bobbin is fully

wound, it will stop automatically. Stop the machine

and return the bobbin winder to its original position

by moving the spindle to the left. Cut the thread as

shown.

z x

v

b n

e

m

,

c

q

w

Elna Lotus Sewing Machine Instruction Manual

www.janomeflyer.com

Lotus Owners Manual/ User Guide

JanomeFlyer.com

14

•Insertingthebobbin

z Place a bobbin in the bobbin holder w with the

thread running off counterclockwise.

q End of thread

w Bobbin holder

x Guide the thread into the ﬁrst notch e on the front

side of the bobbin holder.

e Notch

c Draw the thread to the left, sliding it between the

tension spring blades.

v Continue to draw the thread lightly until the thread

slips into the second notch r. Pull out about 4˝ (10

cm) of thread.

r Notch

b Attach the hook cover plate. Check the threading

by referring to the diagram t shown on the hook

cover plate.

t Threading diagram

y End of thread

z

x

c

v

b

q

e

r

t

w

y

Elna Lotus Sewing Machine Instruction Manual

www.janomeflyer.com

Lotus Owners Manual/ User Guide

JanomeFlyer.com

15

ThreadingtheMachine

Raise the presser foot. Press the needle up/down button

q to raise the thread take-up lever to its highest position.

q Needle up/down button

CAUTION:

Turn OFF the power switch before threading the

machine.

•Threadingthemachine

z Turn the spool thread guide w in the direction of

arrow as illustrated.

Pass the end of the thread through the spool

thread guide w.

x Pass the thread through the thread guide (A) e.

q

w

z

x

c

v

b

z x

c v

b n

e

r

t

y

n

m

u

i

c Draw the thread around the thread guide (B) r.

v Draw the end of the thread down around the check

spring holder t.

t Check spring holder

b Firmly draw the thread up from right to left over the

take-up lever, and down into the take-up lever eye

y.

n Pass the thread through the lower thread guide

u. Slide the thread behind the needle bar thread

guide on the left i.

m Thread the needle from front to back, or use the

needle threader (see page 16).

m

Elna Lotus Sewing Machine Instruction Manual

www.janomeflyer.com

Lotus Owners Manual/ User Guide

JanomeFlyer.com

16

NOTE:

The needle threader can be used with a #11 to #16

needle or a blue tipped needle. Thread sizes 50 to 90

are recommended.

•NeedleThreader

CAUTION:

Turn OFF the power switch when using the needle

threader.

z Lower the presser foot. Raise the needle to its

highest position. Pull down the needle threader

knob q as far as it will go. The hook comes out

through the needle eye from behind.

q Knob

x Draw the thread from guide (a) e to guide (b) r

and under the hook w. Draw the thread up along

the right side of guide (b) r and slip the thread in

between guide (b) and the holder plate t.

w Hook

e Guide (a)

r Guide (b)

t Holder plate

c Raise the knob in the direction of the arrow,

drawing the thread loop through the needle.

v Pull the thread through the needle eye.

q

w

t

r

w

e

z

x

c

v

Elna Lotus Sewing Machine Instruction Manual

www.janomeflyer.com

Lotus Owners Manual/ User Guide

JanomeFlyer.com

17

•DrawinguptheBobbinThread

z Raise the presser foot. Hold the needle thread

lightly with your left hand.

x Press the needle up/down button q twice to lower

and raise the needle to pick up the bobbin thread.

q Needle up/down button

c Pull both threads 4˝ to 6˝ (10 to 15 cm) under and

behind the presser foot.

q

z

x

c

Elna Lotus Sewing Machine Instruction Manual

www.janomeflyer.com

Lotus Owners Manual/ User Guide

JanomeFlyer.com

18

•Tensionistooloose

q Needle thread (top thread)

w Bobbin thread (bottom thread)

e To tighten tension

r Right side (top side) of fabric

t Wrong side (bottom side) of fabric

The needle thread shows through on the wrong side

of the fabric, and the stitch feels bumpy. Turn the dial

to a higher tension setting number to tighten the

needle thread tension.

•Tensionistootight

q Needle thread (top thread)

w Bobbin thread (bottom thread)

e To loosen tension

r Right side (top side) of fabric

t Wrong side (bottom side) of fabric

The bobbin thread shows through on the right side

of the fabric, and the stitch feels bumpy. Turn the

dial to a lower tension setting number to loosen the

needle thread tension.

AdjustingtheNeedleThreadTension

•Correcttension

q Needle thread (top thread)

w Bobbin thread (bottom thread)

e To loosen

r To tighten

The ideal straight stitch has threads locked between

two layers of fabric, as illustrated (magniﬁed to show

detail).

If you look at the top and bottom of the seam, notice

that the stitches are evenly balanced.

For an ideal zigzag stitch, the bobbin thread does not

show on the right side (top side) of the fabric, and the

needle thread shows slightly.

When adjusting the needle thread tension, the higher

the number, the tighter the needle thread tension.

Results depend on:

- stiffness and thickness of the fabric

- number of fabric layers

- type of stitch

q

w

e

r

w

e

r

t

q

w

r

t

e

Elna Lotus Sewing Machine Instruction Manual

www.janomeflyer.com

Lotus Owners Manual/ User Guide

Strona jest ładowana ...

JANOME Elna Lotus Instrukcja obsługi

JANOME Elna Lotus Instrukcja obsługi

w innych językach

Powiązane dokumenty

Inne dokumenty