Samsung SCC-C7439P Instrukcja obsługi

SCC-C7439P

imagine the possibilities

Thanks you for purchasing this Samsung product.

To receive a more complete service, please visit

our website

www.samsungsecurity.com

Smart Dome Camera

User Manual

00955J-EU2_SCC-C7439P-ENG-1.indd1 1 2009-11-18 14:26:57

2_ overview

overview

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER

SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol indicates that dangerous voltage consisting a risk of

electric shock is present within this unit.

This symbol indicates that there are important operating and

maintenance instructions in the literature accompanying this unit.

WARNING

To reduce the risk of ﬁre or electric shock, do not expose this appliance to rain or

moisture.

To prevent injury, this apparatus must be securely attached to the ﬂoor/wall in

accordance with the installation instructions.

WARNING

Be sure to use only the standard adapter that is speciﬁed in the speciﬁcation sheet.

Using any other adapter could cause ﬁre, electrical shock, or damage to the

product.

Incorrectly connecting the power supply or replacing battery may cause explosion,

ﬁre, electric shock, or damage to the product.

Do not connect multiple cameras to a single adapter. Exceeding the capacity may

cause abnormal heat generation or ﬁre.

Securely plug the power cord into the power receptacle. Insecure connection may

cause ﬁre.

When installing the camera, fasten it securely and ﬁrmly. The fall of camera may

cause personal injury.

Do not place conductive objects (e.g. screwdrivers, coins, metal parts, etc.) or

containers ﬁlled with water on top of the camera. Doing so may cause personal

injury due to ﬁre, electric shock, or falling objects.

Do not install the unit in humid, dusty, or sooty locations. Doing so may cause ﬁre

or electric shock.



1.

2.

3.

4.

5.

6.

7.

00955J-EU2_SCC-C7439P-ENG-1.indd2 2 2009-11-18 14:26:57

English _3

English

If any unusual smells or smoke come from the unit, stop using the product. In such

case, immediately disconnect the power source and contact the service center.

Continued use in such a condition may cause ﬁre or electric shock.

If this product fails to operate normally, contact the nearest service center. Never

disassemble or modify this product in any way. (SAMSUNG is not liable for

problems caused by unauthorized modiﬁcations or attempted repair.)

When cleaning, do not spray water directly onto parts of the product. Doing so may

cause ﬁre or electric shock

Do not expose the product to the direct airﬂow from an air conditioner.

Otherwise, it may cause moisture condensation inside the Clear Dome due to

temperature difference between internal and external of the dome camera.

If you install this product in a low-temp area such as inside a cold store, you must

seal up the wiring pipe with silicon, so that the external air can not ﬂow inside the

housing. Otherwise, external high, humid air may ﬂow inside the housing, pooling

moisture or vapor inside the product due to a difference between internal and

external temperature.

CAUTION

Do not drop objects on the product or apply strong blows to it. Keep away from a

location subject to excessive vibration or magnetic interference.

Do not install in a location subject to high temperature (over 50°C), low temperature

(below -50°C), or high humidity. Doing so may cause ﬁre or electric shock.

If you want to relocate the already installed product, be sure to turn off the power

and then move or reinstall it.

Remove the power plug from the outlet when there is a lighting storm. Neglecting

to do so may cause ﬁre or damage to the product.

Keep out of direct sunlight and heat radiation sources. It may cause ﬁre.

Install it in a place with good ventilation.

Avoid aiming the camera directly towards extremely bright objects such as sun, as

this may damage the CCD image sensor.

Apparatus shall not be exposed to dripping or splashing and no objects ﬁlled with

liquids, such as vases, shall be placed on the apparatus.

The Mains plug is used as a disconnect device and shall stay readily operable at

any time.

When the unit is stored in high humidity environment, moisture may occur inside

the cover dome of the Housing. Before installation, please open the cover dome

and wipe off all moisture with a soft dry cloth.

8.

9.

10.

11.

12.

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

00955J-EU2_SCC-C7439P-ENG-1.indd3 3 2009-11-18 14:26:57

overview

4_ overview

IMPORTANT SAFETY INSTRUCTIONS

Read these instructions.

Keep these instructions.

Heed all warnings.

Follow all instructions.

Do not use this apparatus near water.

Clean only with dry cloth.

Do not block any ventilation openings. Install in accordance with the manufacturer’s

instructions.

Do not install near any heat sources such as radiators, heat registers, or other

apparatus (including ampliﬁers) that produce heat.

Do not defeat the safety purpose of the polarized or grounding-type plug.

A polarized plug has two blades with one wider than the other. A grounding type

plug has two blades and a third grounding prong. The wide blade or the third prong

is provided for your safety. If the provided plug does not ﬁt into your outlet, consult

an electrician for replacement of the obsolete outlet.

Protect the power cord from being walked on or pinched particularly at plugs,

convenience receptacles, and the point where they exit from the apparatus.

Only use attachments/accessories speciﬁed by the manufacturer.

Use only with the cart, stand, tripod, bracket, or table speciﬁed

by the manufacturer, or sold with the apparatus. When a

cart is used, use caution when moving the cart/apparatus

combination to avoid injury from tip-over.

Unplug this apparatus during lightning storms or when unused

for long periods of time.

Refer all servicing to qualiﬁed service personnel. Servicing is required when the

apparatus has been damaged in any way, such as powersupply cord or plug is

damaged, liquid has been spilled or objects have fallen into the apparatus, the

apparatus has been exposed to rain or moisture, does not operate normally, or has

been dropped.

Apparatus shall not be exposed to dripping or splashing and no objects

filled with liquids, such as vases, shall be placed on the apparatus

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

11.

12.

13.

14.

00955J-EU2_SCC-C7439P-ENG-1.indd4 4 2009-11-18 14:26:58

English _5

English

CONTENTS

OVERVIEW

2

4 Important Safety Instructions

5 Contents

6 Features

6 What’s Included

7 At a Glance

INSTALLATION &

CONNECTION

8

8 Optional Accessories for

Installation

10 Precautions

10 Preparation

11 Installation

14 Initial Setup

17 Connecting with other Device

SETUP

20

20 How to use the Keyboard

Controller

21 Main Menu

22 Proﬁle

24 Camera Set

33 Intelligent Video

34 Privacy Zone

35 Preset

37 Auto Set

41 Zone Set

42 Alarm Set

44 Clock Set

44 Other Set

46 Communication

46 System Info

47 Language

APPENDIX

48

48 Shortcut Keys

49 Speciﬁcations

51 Product Appearance

00955J-EU2_SCC-C7439P-ENG-1.indd5 5 2009-11-18 14:26:58

overview

6_ overview

FEATURES

With the state-of-the-art digital signal processing technology, full digital image

processing and special algorithm of 600-line high resolution implemented

High performance surveillance camera, equipped with x34 zoom lens and digital

zoom IC, enabling monitoring up to 544 times

WDR to cover the full screen irregardless of its brightness

DAY/NIGHT to improve the sensitivity by automatic conversion into the black and

white mode at night or in the environment with low illumination

White Balance to control the brightness to the illumination

Backlight Compensation under spotlight or utmost bright illumination

Auto Focus to automatically adjust the focus to the subject movement

Privacy zone to hide a speciﬁc area for personal privacy

PAN/TILT for precise control at high speed

WHAT’S INCLUDED

Please check if your camera and accessories are all included in the product package.

Camera Housing Connectors

User Manual Grease Pin & Bush



00955J-EU2_SCC-C7439P-ENG-1.indd6 6 2009-11-18 14:27:01

English _7

English

AT A GLANCE

CAMERA

FRAME SET

Wipe out a dirty surface of the lens softly with a lens tissue or cloth to which you

have applied ethanol.

M



LENS

HOOK

ALARM IN

ALARM OUT

RS-485

POWER

INPUT

00955J-EU2_SCC-C7439P-ENG-1.indd7 7 2009-11-18 14:27:11

8_ installation & connection

installation & connection

OPTIONAL ACCESSORIES FOR INSTALLATION

For your easier installation, you can purchase appropriate optional accessories available.

WALL MOUNT ADAPTOR (SCX-300WM)

This is a wall mount adaptor, used for wall-

mounted installation of SMART DOME

CAMEA units.

CEILING MOUNT ADAPTOR (SCX-300CM)

This is a ceiling mount adaptor, used for

installation of SMART DOME CAMEA units on

a concrete ceiling.

POLE MOUNT ADAPTOR (SCX-300PM)

This is an adaptor for WALL MOUNT

ADAPTOR (SCX-300WM) installation on a

pole whose diameter is bigger than 80mm.

1.

2.

3.

00955J-EU2_SCC-C7439P-ENG-1.indd8 8 2009-11-18 14:27:13

English _9

English

CORNER MOUNT ADAPTOR (SCX-300KM)

This is an adaptor for WALL MOUNT

ADAPTOR (SCX-300WM) installation on the

corner of wall joint.

PARAPET (LONG) MOUNT (SCX-300LM)

This is a mounting kit used for installation of

SMART DOME CAMEA units on a parapet.

4.

5.

00955J-EU2_SCC-C7439P-ENG-1.indd9 9 2009-11-18 14:27:13

installation & connection

10_ installation & connection

PRECAUTIONS

Select an installation spot which can endure more than 4 times of the product

weight.

When installing, prevent peoples approaching to avoid personal injury.

Move valuables to a safer place before installing.

PREPARATION

Run all the external cables through the bracket adaptor’s PIPE or MOUNT hole.

Wrap around the HOUSING’s screw hole with the Teflon Tape.

1.

2.

PIPE OR

MOUNT

1.5" PT

EXTERNAL

CABLE

1.5" PT

TEFLON TAPE

HOUSING

00955J-EU2_SCC-C7439P-ENG-1.indd10 10 2009-11-18 14:27:14

English _11

English

INSTALLATION

Press the SNAP FIT of the ADAPTOR in the HOUSING to open the ADAPTOR

part, and then insert all external cables into the HOUSING. Secure the HOUSING

on the PIPE or MOUNT by turning it clockwise.

(Secure two components tightly, to avoid loosened HOUSING.)

Connect external cables to the CONNECTORS(ALARM IN, POWER, RS-485,

ALARM OUT) and connect the CONNECTOR to the ADAPTOR.

Insert the cable into the FRAME SET, and close the ADAPTOR.

Then, wrap the BNC JACK with the INSULATION TUBE, and use an insulation tape

to seal up the end of the INSULATION TUBE so that the BNC JACK does not

protrude outside of the INSULATION TUBE coating.

For more information about cable connection, refer to Connecting the adaptor

cable. (page 19)

1.

2.

M



PIPE OR

MOUNT

HOUSING

EXTERNAL

CABLE

ADAPTOR

SNAP-FIT

PIPE OR

MOUNT

HOUSING

EXTERNAL

CABLE

ADAPTOR

BNC JACK

INSULATION

TUBE

ALARM OUT

ALARM IN

RS-485

POWER INPUT

00955J-EU2_SCC-C7439P-ENG-1.indd11 11 2009-11-18 14:27:19

installation & connection

12_ installation & connection

Note that BUSHINGs are provided for outdoor installations where exposed to a

moisture condition through the PIPE or MOUNT, install the HOUSING using the

BUSHING to prevent moisture entering.

- Apply grease of proper dose on the BUSHING before assembling, and run

cables through each hole of the bushings. Use PINS to stop up empty holes

having no cable running.

- Assemble the

BUSHING to the top side of HOUSING’s inside as shown in the

diagram below. At the moment, apply pressure evenly on the BUSHING to

secure it tightly to the HOUSING as shown in the diagram.

BUSH

ETC CABLE

POWER

(24V) CABLE

BNC CABLE

BUSH



BUSH

HOUSING

PIPE OR

MOUNT

BUSH

HOUSING

00955J-EU2_SCC-C7439P-ENG-1.indd12 12 2009-11-18 14:27:24

English _13

English

Tie up the SAFETY WIRE of the CAMERA on the BRACKET WIRE of the FRAME

SET.

Arrange the 22P CONNECTOR of the CAMERA in line with that of the ADAPTOR,

push the HOOKs on either end of the CAMERA in the RACK direction of the

FRAME SET to secure the two.

Then, ensure that all of the two HOOKs clicks to ﬁx to the RACK properly.

When the installation is completed, remove the PROTECTIVE COVER and

PRETOECTIVE TAPE from the lens.

Align each of the 3 SCREWS of COVER DOME and 3 SCREW HOLEs of the

HOUSING respectively, and assemble the COVER DOME and HOUSING. During

the assembling, note on the followings.

Insert and arrange SAFETY WIRE into the HOUSING while not disturbing the

camera operation.

Ensure that the GASKET DOME component does not separate from the

COVER DOME. (If the GASKET DOME is not properly assembled, it damages

the waterproofness.)

3.

M



4.



22P CONNECTOR

HOUSING

RACK

BRACKET WIRE

FRAME SET

SAFETY WIRE

HOOK

CAMERA

PROTECTIVE

COVER

PROTECTIVE

TAPE

SCREWS

HOUSING

COVER DOME

GASKET DOME

CAMERA

HOUSING

SAFETY WIRE

00955J-EU2_SCC-C7439P-ENG-1.indd13 13 2009-11-18 14:27:29

installation & connection

14_ installation & connection

INITIAL SETUP

Camera Address Setup

Use SW606, SW605, and SW604 to specify the camera address.

You can specify between 0 and 255 for the address, where the hundreds digit is

with SW606, the tens digit with SW605, and the ones digit with SW604.

ex) Camera address: If the address is 1, follow the steps in the figure below.

Communication Protocol Setup

Use pins #1~#4 of SW603 to specify the communication protocol.

Comp

PIN1 PIN2 PIN3 PIN4

A OFF OFF OFF OFF

B ON OFF OFF OFF

C OFF ON OFF OFF

D ON ON OFF OFF

E OFF OFF ON OFF

F ON OFF ON OFF

G OFF ON ON OFF

H ON ON ON OFF

I OFF OFF OFF ON

J ON OFF OFF ON

K OFF ON OFF ON

L ON ON OFF ON

M OFF OFF ON ON

N ON OFF ON ON

O OFF ON ON ON

P ON ON ON ON

A : SAMSUNG HALF

B : SAMSUNG FULL

SW606

(x100)

SW605

(x10)

SW604

(x1)

00955J-EU2_SCC-C7439P-ENG-1.indd14 14 2009-11-18 14:27:35

English _15

English

Baud Rate Setup

Use pins #5, #6 of SW603 to set the baud rate.

BAUD RATE PIN 5 PIN 6

4800 BPS ON ON

9600 BPS OFF ON

19200 BPS ON OFF

38400 BPS OFF OFF

The factory default is 9600 BPS.

Setting RS-422A/RS-485 Termination

As it is shown in the structure map, when Controller and RS-422A/RS-485 is

connected, it should be terminated according to the Cable feature of impedance

on the each end of the transmitting line to transfer the signals in long distance by

controlling the reflection of the signals to the lowest.

Termination : Using numbers 1 and 2 PIN, turn to <ON> and it will be terminated.

Controller

Termination

n < 32

Termination

SW1-ON

CAM n

CAM n-1

CAM 2

CAM 1

TX+(DATA+)

TX-(DATA-)

RX-

RX+

RX+ RX- RX+ RX- RX+ RX-

<RS-485 Half Duplex Organization>

00955J-EU2_SCC-C7439P-ENG-1.indd15 15 2009-11-18 14:27:35

installation & connection

16_ installation & connection

A communication error may occur if you connect multiple cameras that are assigned

the same address in the network.

M



Controller

Termination

n < 32

Termination

SW1-ON

SW2-ON

CAM n

CAM n-1

CAM 2CAM 1

<RS-422A/RS-485 Full Duplex Organization>

00955J-EU2_SCC-C7439P-ENG-1.indd16 16 2009-11-18 14:27:36

English _17

English

CONNECTING WITH OTHER DEVICE

Connecting to a monitor

Connect one end of the BNC

video cable connector to the

Video Output Terminal (VIDEO

OUT).

Connect the other end of the

connector to the Video Input

Terminal of the monitor.

1.

2.

Video terminal on the

rear of monitor

BNC Cable

MONITOR

ALARM IN

POWER SOURCE

ALARM OUT

CONTROLLER/DVR

00955J-EU2_SCC-C7439P-ENG-1.indd17 17 2009-11-18 14:27:37

installation & connection

18_ installation & connection

To connect ALARM IN

Connect one end of the external device's signal line to a corresponding ALARM

IN port of the monitor.

Connect the other end of the signal line to the earth-grounding [GND] port.

To connect ALARM OUT

Connect one end of the external device's signal line to a corresponding ALARM

OUT port of the monitor.

Connect the other end of the signal line to the common [COM] port.

To connect the controller

Connect an external controller or DVR to the camera, with which you can adjust the

camera.

Connect the Rx+ pin of the

camera to the Tx+ pin of the

controller.

Connect the Rx- pin of the

camera to the Tx- pin of the

controller.

Connect the Tx+ pin of the

camera to the Rx+ pin of the

controller.

Connect the Tx- pin of the

camera to the Rx- pin of the

controller.

1.

2.

1.

2.

1.

2.

3.

4.

TxRx

00955J-EU2_SCC-C7439P-ENG-1.indd18 18 2009-11-18 14:27:38

English _19

English

Connecting the adaptor cable

Power Supply

Connect the cables as necessary, and turn on the camera to check if it works

properly.

Connect the adaptor to the power terminal of the camera.

Plug the power cord of the adaptor into the wall outlet.

1.

2.

Adaptor Board

00955J-EU2_SCC-C7439P-ENG-1.indd19 19 2009-11-18 14:27:39

20_ setup

setup

Connect the camera to the keyboard controller or DVR, with which you

can manipulate and change the settings of the camera.

HOW TO USE THE KEYBOARD CONTROLLER

Follow the steps below to set the camera menu using the controller.

Open the Camera Setup screen.

Use the joystick to navigate through the menus.

Press [ENTER] to select a menu item.

Use the joystick to change the value of the selected item.

Press [ENTER] to apply your changes.

Using OSD icons

_+

:

If these icons appear in the left and right corner of a menu item, you can use

the joystick to move to the previous or next menu.

(EXIT): Exits the menu setup screen.

Before exiting the setup screen, select <SAVE> to save your settings

to the whole menus, or <QUIT> to cancel them.

(RET): Saves your settings and returns to the previous screen.

(HOME): Returns to the main menu.

(SAVE): Use this icon if you want to save your settings after you speciﬁed the

mask area and privacy area, etc.

Once you saved your settings, the changes remain intact even if you

select <QUIT> on exit.

(DEL): Use this icon if you want to delete a mask, or privacy area, etc.

Once you deleted your settings, the deletions remain valid even if you

select <QUIT> on exit.

: This icon appears in the right of a menu containing sub menu items.

While any operation of PRESET, AUTO PAN, SCAN, and PATTERN is running, and if

the camera is turned off and back on without any particular manipulation, the

camera will resume the last run operation.

You can set the menu item only if the tilt angle is within 90°.

If you enter the menu setup screen with the camera positioned out of a tilt of 90°,

the camera will rotate by 180° to fall into the opposite position within a tilt of 90°.

1.

2.

3.

4.

5.



M



00955J-EU2_SCC-C7439P-ENG-1.indd20 20 2009-11-18 14:27:39

Strona jest ładowana ...

Samsung SCC-C7439P Instrukcja obsługi

Ten podręcznik jest również odpowiedni dla

Samsung SCC-C7439P Instrukcja obsługi

w innych językach

Powiązane dokumenty

Inne dokumenty