Samsung SCC-C6439N Instrukcja obsługi

User Manual

Smart Dome Camera

SCC-C6439P

imagine the possibilities

Thanks you for purchasing this Samsung product.

To receive a more complete service, please visit

our website

www.samsungsecurity.com

00882K-EU2_SCC-C6439P-ENG-1.indd1 1 2009-10-10 10:35:25

2_ overview

overview

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER

SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol indicates that dangerous voltage consisting a risk of

electric shock is present within this unit.

This symbol indicates that there are important operating and

maintenance instructions in the literature accompanying this unit.

WARNING

To reduce the risk of ﬁre or electric shock, do not expose this appliance to rain or

moisture.

To prevent injury, this apparatus must be securely attached to the ﬂoor/wall in

accordance with the installation instructions.

WARNING

Be sure to use only the standard adapter that is speciﬁed in the speciﬁcation sheet.

Using any other adapter could cause ﬁre, electrical shock, or damage to the

product.

Incorrectly connecting the power supply or replacing battery may cause explosion,

ﬁre, electric shock, or damage to the product.

Do not connect multiple cameras to a single adapter. Exceeding the capacity may

cause abnormal heat generation or ﬁre.

Securely plug the power cord into the power receptacle. Insecure connection may

cause ﬁre.

When installing the camera, fasten it securely and ﬁrmly. The fall of camera may

cause personal injury.

Do not place conductive objects (e.g. screwdrivers, coins, metal parts, etc.) or

containers ﬁlled with water on top of the camera. Doing so may cause personal

injury due to ﬁre, electric shock, or falling objects.

Do not install the unit in humid, dusty, or sooty locations. Doing so may cause ﬁre

or electric shock.



1.

2.

3.

4.

5.

6.

7.

00882K-EU2_SCC-C6439P-ENG-1.indd2 2 2009-10-10 10:35:26

English _3

English

If any unusual smells or smoke come from the unit, stop using the product. In such

case, immediately disconnect the power source and contact the service center.

Continued use in such a condition may cause ﬁre or electric shock.

If this product fails to operate normally, contact the nearest service center. Never

disassemble or modify this product in any way. (SAMSUNG is not liable for

problems caused by unauthorized modiﬁcations or attempted repair.)

When cleaning, do not spray water directly onto parts of the product. Doing so may

cause ﬁre or electric shock

Do not expose the product to the direct airﬂow from an air conditioner.

Otherwise, it may cause moisture condensation inside the Clear Dome due to

temperature difference between internal and external of the dome camera.

If you install this product in a low-temp area such as inside a cold store, you must

seal up the wiring pipe with silicon, so that the external air can not ﬂow inside the

housing. Otherwise, external high, humid air may ﬂow inside the housing, pooling

moisture or vapor inside the product due to a difference between internal and

external temperature.

CAUTION

Do not drop objects on the product or apply strong blows to it. Keep away from a

location subject to excessive vibration or magnetic interference.

Do not install in a location subject to high temperature (over 50°C), low temperature

(below -10°C), or high humidity. Doing so may cause ﬁre or electric shock.

If you want to relocate the already installed product, be sure to turn off the power

and then move or reinstall it.

Remove the power plug from the outlet when there is a lighting storm. Neglecting

to do so may cause ﬁre or damage to the product.

Keep out of direct sunlight and heat radiation sources. It may cause ﬁre.

Install it in a place with good ventilation.

Avoid aiming the camera directly towards extremely bright objects such as sun, as

this may damage the CCD image sensor.

Apparatus shall not be exposed to dripping or splashing and no objects ﬁlled with

liquids, such as vases, shall be placed on the apparatus.

The Mains plug is used as a disconnect device and shall stay readily operable at

any time.

When using the camera outdoors, moisture may occur inside the camera due

to temperature difference between indoors and outdoors. For this reason, it is

recommended to install the camera indoors. For outdoor use, use the camera with

built-in fan and heater.

8.

9.

10.

11.

12.

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

00882K-EU2_SCC-C6439P-ENG-1.indd3 3 2009-10-10 10:35:26

overview

4_ overview

IMPORTANT SAFETY INSTRUCTIONS

Read these instructions.

Keep these instructions.

Heed all warnings.

Follow all instructions.

Do not use this apparatus near water.

Clean only with dry cloth.

Do not block any ventilation openings. Install in accordance with the manufacturer’s

instructions.

Do not install near any heat sources such as radiators, heat registers, or other

apparatus (including ampliﬁers) that produce heat.

Do not defeat the safety purpose of the polarized or grounding-type plug.

A polarized plug has two blades with one wider than the other. A grounding type

plug has two blades and a third grounding prong. The wide blade or the third prong

is provided for your safety. If the provided plug does not ﬁt into your outlet, consult

an electrician for replacement of the obsolete outlet.

Protect the power cord from being walked on or pinched particularly at plugs,

convenience receptacles, and the point where they exit from the apparatus.

Only use attachments/accessories speciﬁed by the manufacturer.

Use only with the cart, stand, tripod, bracket, or table speciﬁed

by the manufacturer, or sold with the apparatus. When a

cart is used, use caution when moving the cart/apparatus

combination to avoid injury from tip-over.

Unplug this apparatus during lightning storms or when unused

for long periods of time.

Refer all servicing to qualiﬁed service personnel. Servicing is required when the

apparatus has been damaged in any way, such as powersupply cord or plug is

damaged, liquid has been spilled or objects have fallen into the apparatus, the

apparatus has been exposed to rain or moisture, does not operate normally, or has

been dropped.

Apparatus shall not be exposed to dripping or splashing and no objects

filled with liquids, such as vases, shall be placed on the apparatus

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

11.

12.

13.

14.

00882K-EU2_SCC-C6439P-ENG-1.indd4 4 2009-10-10 10:35:26

English _5

English

CONTENTS

OVERVIEW

2

4 Important Safety Instructions

5 Contents

6 Features

6 What’s Included

7 At a Glance

INSTALLATION &

CONNECTION

8

8 Preparing Installation

8 Installation

12 Initial Setup

15 Connecting With Other Device

SETUP

18

18 How to use the Keyboard

Controller

19 Main Menu

20 Proﬁle

22 Camera Set

31 Intelligent Video

32 Privacy Zone

33 Preset

35 Auto Set

39 Zone Set

40 Alarm Set

42 Clock Set

42 Other Set

44 Communication

44 System Info

45 Language

APPENDIX

46

46 Shortcut Keys

47 Speciﬁcations

49 Product Appearance

00882K-EU2_SCC-C6439P-ENG-1.indd5 5 2009-10-10 10:35:27

overview

6_ overview

FEATURES

With the state-of-the-art digital signal processing technology, full digital image

processing and special algorithm of 600-line high resolution implemented

High performance surveillance camera, equipped with x34 zoom lens and digital

zoom IC, enabling monitoring up to 544 times

WDR to cover the full screen irregardless of its brightness

DAY/NIGHT to improve the sensitivity by automatic conversion into the black and

white mode at night or in the environment with low illumination

White Balance to control the brightness to the illumination

Backlight Compensation under spotlight or utmost bright illumination

Auto Focus to automatically adjust the focus to the subject movement

Privacy zone to hide a speciﬁc area for personal privacy

PAN/TILT for precise control at high speed

WHAT’S INCLUDED

Please check if your camera and accessories are all included in the product package.

Camera Frame Set Cover

User Manual Template Connectors



00882K-EU2_SCC-C6439P-ENG-1.indd6 6 2009-10-10 10:35:31

English _7

English

AT A GLANCE

CAMERA

FRAME SET

Wipe out a dirty surface of the lens softly with a lens tissue or cloth to which you

have applied ethanol.

M



LENS

HOOK

ALARM IN

ALARM OUT

RS-485

POWER

INPUT

00882K-EU2_SCC-C6439P-ENG-1.indd7 7 2009-10-10 10:35:37

8_ installation & connection

installation & connection

PREPARING INSTALLATION

Use the ceiling installation template when you install the camera on the ceiling on

your own.

Run the cables through the “



” shaped hole on the center of the template, and

remove ﬁlms on the adhesives, and then attach the template on the desired location

on the ceiling.

When installing the frames set, align all template’s screw holes and those of the

frames set.

This template prevents dust entering from the ceiling into the camera assembly.

INSTALLATION

Press the “SNAP FIT” on the “ADAPTOR” to open the “ADAPTOR”, and arrange

cables so they pass out of the “FRAME SET”.



1.

EXTERNAL

CABLES

FRAME SET

ADAPTOR

SNAP FIT

ADAPTOR

SNAP FIT

CABLESCEILING CABLESCEILING TEMPLATE

00882K-EU2_SCC-C6439P-ENG-1.indd8 8 2009-10-10 10:35:42

English _9

English

Use the three “SCREWS” to ﬁx the “FRAME SET” on a “CAMERA” installation

position.

Connect external cables to the “CONNECTORS(ALARM IN, POWER, RS-485,

ALARM OUT)”and connect the “CONNECTOR” to the “ADAPTOR”.

Insert the cable into the “FRAME SET”, and close the “ADAPTOR”.

Then, wrap the “BNC JACK” with the “INSULATION TUBE”, and use an insulation

tape to seal up the end of the “INSULATION TUBE” so that the “BNC JACK” does

not protrude outside of the “INSULATION TUBE” coating.

For more information about cable connection, refer to “Connecting the adaptor

cable”. (page 17)

2.

3.

M



FRAME SET

ADAPTOR

SNAP FIT

INSULATION TUBE

BNC JACK

ALARM OUT

ALARM IN

RS-485

POWER INPUT

FRAME SET

ADAPTOR

SCREW

00882K-EU2_SCC-C6439P-ENG-1.indd9 9 2009-10-10 10:35:50

installation & connection

10_ installation & connection

Connect the “SAFETY WIRE” of the “CAMERA” to the “BRACKET WIRE” on the

“FRAME SET”. Arrange the “22P CONNECTOR” of the “CAMERA” in line with that

of the “ADAPTOR”, push the “HOOK” on either end of the “CAMERA” in the “RACK”

direction of the “FRAME SET” to secure the two.

Then, ensure that all of the two “HOOKS” “clicks” to ﬁx to the “RACK” properly.

When the installation is completed, remove the “PROTECTIVE FILM” and

“PROTECTIVE TAPE” from on the lens.

4.

M



FRAME SET

22P CONNECTOR

CAMERA

SAFETY WIRE

BRACKET WIRE

FRAME SET

CAMERA

RACK

HOOK

RACK

HOOK

CAMERA

FRAME SET

PROTECTIVE FILM

PROTECTIVE TAPE

00882K-EU2_SCC-C6439P-ENG-1.indd10 10 2009-10-10 10:35:59

English _11

English

Arrange the “COVER” arrow in line with the “FRAME SET” arrow, and push in the

“COVER”. Insert the “COVER” to the end, and turn the “COVER” clockwise.

As shown in the ﬁgure below, turn it until you see the “BUTTON” hole and hear a

click.

Ensure that the “COVER” should not move any further if you turn the “COVER” counter

clockwise.

If you want to remove the “COVER”, hold down the “BUTTON” and turn the

“COVER” counter clockwise to remove the “COVER”.

5.



FRAME SET

BUTTON

CAMERA

COVER

BUTTON

COVER

00882K-EU2_SCC-C6439P-ENG-1.indd11 11 2009-10-10 10:36:03

installation & connection

12_ installation & connection

INITIAL SETUP

Camera Address Setup

Use SW606, SW605, and SW604 to specify the camera address.

You can specify between 0 and 255 for the address, where the hundreds digit is

with SW606, the tens digit with SW605, and the ones digit with SW604.

ex) Camera address: If the address is 1, follow the steps in the figure below.

Communication Protocol Setup

Use pins #1~#4 of SW603 to specify the communication protocol.

Comp

PIN1 PIN2 PIN3 PIN4

A OFF OFF OFF OFF

B ON OFF OFF OFF

C OFF ON OFF OFF

D ON ON OFF OFF

E OFF OFF ON OFF

F ON OFF ON OFF

G OFF ON ON OFF

H ON ON ON OFF

I OFF OFF OFF ON

J ON OFF OFF ON

K OFF ON OFF ON

L ON ON OFF ON

M OFF OFF ON ON

N ON OFF ON ON

O OFF ON ON ON

P ON ON ON ON

A : SAMSUNG HALF

B : SAMSUNG FULL

SW606

(x100)

SW605

(x10)

SW604

(x1)

00882K-EU2_SCC-C6439P-ENG-1.indd12 12 2009-10-10 10:36:06

English _13

English

Baud Rate Setup

Use pins #5, #6 of SW603 to set the baud rate.

BAUD RATE PIN 5 PIN 6

4800 BPS ON ON

9600 BPS OFF ON

19200 BPS ON OFF

38400 BPS OFF OFF

The factory default is 9600 BPS.

Setting RS-422A/RS-485 Termination

As it is shown in the structure map, when Controller and RS-422A/RS-485 is

connected, it should be terminated according to the Cable feature of impedance

on the each end of the transmitting line to transfer the signals in long distance by

controlling the reflection of the signals to the lowest.

Termination : Using numbers 1 and 2 PIN, turn to <ON> and it will be terminated.

Controller

Termination

n < 32

Termination

SW1-ON

CAM n

CAM n-1

CAM 2

CAM 1

TX+(DATA+)

TX-(DATA-)

RX-

RX+

RX+ RX- RX+ RX- RX+ RX-

<RS-485 Half Duplex Organization>

00882K-EU2_SCC-C6439P-ENG-1.indd13 13 2009-10-10 10:36:07

installation & connection

14_ installation & connection

A communication error may occur if you connect multiple cameras that are assigned

the same address in the network.

M



Controller

Termination

n < 32

Termination

SW1-ON

SW2-ON

CAM n

CAM n-1

CAM 2CAM 1

<RS-422A/RS-485 Full Duplex Organization>

00882K-EU2_SCC-C6439P-ENG-1.indd14 14 2009-10-10 10:36:07

English _15

English

CONNECTING WITH OTHER DEVICE

Connecting to a monitor

Connect one end of the BNC

video cable connector to the

Video Output Terminal (VIDEO

OUT).

Connect the other end of the

connector to the Video Input

Terminal of the monitor.

1.

2.

Video terminal on the

rear of monitor

BNC Cable

MONITOR

ALARM IN

POWER SOURCE

ALARM OUT

CONTROLLER/DVR

00882K-EU2_SCC-C6439P-ENG-1.indd15 15 2009-10-10 10:36:08

installation & connection

16_ installation & connection

To connect ALARM IN

Connect one end of the external device's signal line to a corresponding ALARM

IN port of the monitor.

Connect the other end of the signal line to the earth-grounding [GND] port.

To connect ALARM OUT

Connect one end of the external device's signal line to a corresponding ALARM

OUT port of the monitor.

Connect the other end of the signal line to the common [COM] port.

To connect the controller

Connect an external controller or DVR to the camera, with which you can adjust the

camera.

Connect the Rx+ pin of the

camera to the Tx+ pin of the

controller.

Connect the Rx- pin of the

camera to the Tx- pin of the

controller.

Connect the Tx+ pin of the

camera to the Rx+ pin of the

controller.

Connect the Tx- pin of the

camera to the Rx- pin of the

controller.

1.

2.

1.

2.

1.

2.

3.

4.

TxRx

00882K-EU2_SCC-C6439P-ENG-1.indd16 16 2009-10-10 10:36:09

English _17

English

Connecting the adaptor cable

Power Supply

Connect the cables as necessary, and turn on the camera to check if it works

properly.

Connect the adaptor to the power terminal of the camera.

Plug the power cord of the adaptor into the wall outlet.

1.

2.

Adaptor Board

00882K-EU2_SCC-C6439P-ENG-1.indd17 17 2009-10-10 10:36:09

18_ setup

setup

Connect the camera to the keyboard controller or DVR, with which you

can manipulate and change the settings of the camera.

HOW TO USE THE KEYBOARD CONTROLLER

Follow the steps below to set the camera menu using the controller.

Open the Camera Setup screen.

Use the joystick to navigate through the menus.

Press [ENTER] to select a menu item.

Use the joystick to change the value of the selected item.

Press [ENTER] to apply your changes.

Using OSD icons

_+

:

If these icons appear in the left and right corner of a menu item, you can use

the joystick to move to the previous or next menu.

(EXIT): Exits the menu setup screen.

Before exiting the setup screen, select <SAVE> to save your settings

to the whole menus, or <QUIT> to cancel them.

(RET): Saves your settings and returns to the previous screen.

(HOME): Returns to the main menu.

(SAVE): Use this icon if you want to save your settings after you speciﬁed the

mask area and privacy area, etc.

Once you saved your settings, the changes remain intact even if you

select <QUIT> on exit.

(DEL): Use this icon if you want to delete a mask, or privacy area, etc.

Once you deleted your settings, the deletions remain valid even if you

select <QUIT> on exit.

: This icon appears in the right of a menu containing sub menu items.

While any operation of PRESET, AUTO PAN, SCAN, and PATTERN is running, and if

the camera is turned off and back on without any particular manipulation, the

camera will resume the last run operation.

You can set the menu item only if the tilt angle is within 90°.

If you enter the menu setup screen with the camera positioned out of a tilt of 90°,

the camera will rotate by 180° to fall into the opposite position within a tilt of 90°.

1.

2.

3.

4.

5.



M



00882K-EU2_SCC-C6439P-ENG-1.indd18 18 2009-10-10 10:36:10

English _19

English

MAIN MENU

This is the first screen you ever see when you turn on the camera where you can set the

camera environment to your needs.

For selecting and saving each menu item, refer to “How to use the keyboard controller”. (page 18)

PROFILE

Select a mode appropriate to the camera

installation environment.

CAMERA SET

You can conﬁgure the camera settings.

INTELLIGENCE

Offers motion detection and tracking

functions.

PRIVACY ZONE

You can conﬁgure the privacy settings.

PRESET

You can set the PRESET POSITION and

DURATION.

AUTO SET

Contains sub menu items of AUTO PAN,

PATTERN, and SCAN.

ZONE SET

You can set the standard azimuth and zone

area for the camera.

ALARM SET

You can set the alarm priority and I/O sequence.

CLOCK SET

You can set the display time and format.

OTHER SET

You can reset the camera, or adjust the OSD color to your preference.

COMMUNICATION

Conﬁgures the settings pertaining to RS-485 communication.

SYSTEM INFO

Shows the system information such as the camera version or communication

settings.

LANGUAGE

Select a preferred one from the supported languages.





MAIN MENU



PROFILE

CAMERA SET

INTELLIGENCE

PRIVACY ZONE

PRESET

AUTO SET

ZONE SET

ALARM SET

CLOCK SET

OTHER SET

COMMUNICATION

SYSTEM INFO

LANGUAGE

00882K-EU2_SCC-C6439P-ENG-1.indd19 19 2009-10-10 10:36:10

20_ setup

setup

PROFILE

You can select one from the pre-determined configurations as appropriate to your

specific camera installation environment.

Your selection on each item in PROFILE will affect all other settings of the camera.

STANDARD

Automatically optimizes the camera settings

to the normal environment.

ITS

This setting enables you to analyze the trafﬁc

situation and take the trafﬁc information at a

glance.

BACKLIGHT

This setting enables you to view a sharp

background and object even in a severe

backlight scene.

DAY/NIGHT

Automatically optimizes the camera settings to the day and night scene.

GAMING

This automatically configures the settings so that you can work in a stable illumina-

tion condition as indoors.

CUSTOM

Your change to any of the PROFILE settings will switch the display to CUSTOM.



CAMERA SETUP MENU

STANDARD ITS BACKLIGHT DAY/NIGHT GAMING

Parent Menu Sub-menus

VPS OFF ON OFF OFF OFF

IRIS

ALC ALC ALC ALC ALC

ALC - - - - -

LEVEL 0 0 0 0 0

BACKLIGHT OFF OFF WDR OFF OFF

WDR - - - - -

WEIGHT Custom Setting Custom Setting MEDIUM Custom Setting Custom Setting

WDR LEVEL Custom Setting Custom Setting 0 Custom Setting Custom Setting

WHITE BAL Custom Setting Custom Setting Custom Setting Custom Setting Custom Setting



PROFILE





STANDARD

ITS

BACKLIGHT

DAY/NIGHT

GAMING

CUSTOM

00882K-EU2_SCC-C6439P-ENG-1.indd20 20 2009-10-10 10:36:10

Strona się ładuje...

Samsung SCC-C6439N Instrukcja obsługi

Niniejsza instrukcja jest również odpowiednia dla

Samsung SCC-C6439N Instrukcja obsługi

w innych językach

Powiązane artykuły

Inne dokumenty