AAT Novus NV-WIFISET-1 Instrukcja obsługi

User’s ma n ua l

(s h o rt form )

NV-WIFISET-1

NV-WIFISET-1 - User’s manual (short form) ver 1.2

2

IMPORTANT SAFEGUARDS AND WARNINGS

EMC (2014/30/UE) and LVD (2014/35/UE) directives

CE Marking

Our products are manufactured to comply with requirements of the following directives

and national regulations implementing the directives:

• Electromagnetic compatibility EMC 2014/30/UE.

• Low voltage LVD 2014/35/UE with further amendment. The Directive applies to

electrical equipment designed for use with a voltage rating of between 50VAC and

1000VAC as well as 75VDC and 1500VDC.

WEEE Directive 2012/19/UE

Information on Disposal for Users of Waste Electrical and Electronic Equipment

This appliance is marked according to the European 1000VAC Directive on Waste

Electrical and Electronic Equipment (2002/96/EC) and further amendments. By ensuring

this product is disposed of correctly, you will help to prevent potential negative

consequences for the environment and human health, which could otherwise be caused by

inappropriate waste handling of this product.

The symbol on the product, or the documents accompanying the product, indicates that this appliance

may not be treated as household waste. It shall be handed over to the applicable collection point for

used up electrical and electronic equipment for recycling purpose. For more information about

recycling of this product, please contact your local authorities, your household waste disposal service

or the shop where you purchased the product.

RoHS Directive 2011/65/UE

Information concerning the restriction of use of hazardous substances in electrical electronic

equipment.

Out of concern for human health protection and friendly environment, we assure that our

products falling under RoHS Directive regulations, regarding the restriction of the use of

hazardous substances in electrical and electronic equipment, have been designed and

manufactured in compliance with the above mentioned regulations. Simultaneously, we

claim that our products have been tested and do not contain hazardous substances whose

exceeding limits could have negative impact on human health or natural environment

Information

The device, as a part of professional CCTV system used for surveillance and control, is not designed

for self installation in households by individuals without technical knowledge.

Excluding of responsibility in case of damaging data on a disk or other devices:

The manufacturer does not bear any responsibility in case of damaging or losing data on a disk or other

devices during device operation.

WARNING!

PRIOR TO UNDERTAKING ANY ACTION THAT IS NOT DESCRIBED FOR THE GIVEN

PRODUCT IN USER’S MANUAL AND OTHER DOCUMENTS DELIVERED WITH THE

PRODUCT, OR IF IT DOES NOT ARISE FROM THE USUAL APPLICATION OF THE

PRODUCT, MANUFACTURER MUST BE CONTACTED UNDER THE RIGOR OF EXCLUDING

THE MANUFACTURER’S RESPONSIBILITY FOR THE RESULTS OF SUCH AN ACTION.

NV-WIFISET-1 - User’s manual (short form) ver 1.2

3

IMPORTANT SAFEGUARDS AND WARNINGS

WARNING!

THE KNOWLEDGE OF THIS SHORT MANUAL IS AN INDESPENSIBLE CONDITION OF A

PROPER DEVICE ISTALLATION AND CONFIGURATION. YOU ARE KINDLY REQUSTED TO

FAMILIRIZE YOURSELF WITH THE FULL USER MANUAL PRIOR TO FURTHER DEVICE

EXPLOATATION. FULL USER MANUAL IS AVAILABLE ON www.novuscctv.com/en

WARNING!

USER IS NOT ALLOWED TO DISASSEMBLE THE CASING AS THERE ARE NO USER-

SERVICEABLE PARTS INSIDE THIS UNIT. ONLY AUTHORIZED SERVICE PERSONNEL

MAY OPEN THE UNIT.

INSTALLATION AND SERVICING SHOULD ONLY BE DONE BY QUALIFIED SERVICE

PERSONNEL AND SHOULD CONFORM TO ALL LOCAL REGULATIONS

1. Prior to undertaking any action please consult the following manual and read all the safety and

operating instructions before starting the device.

2. Please keep this manual for the lifespan of the device in case referring to the contents of this manual

is necessary;

3. All the safety precautions referred to in this manual should be strictly followed, as they have a direct

influence on user’s safety and durability and reliability of the device;

4. All actions conducted by the servicemen and users must be accomplished in accordance with the

user’s manual;

5. The device should be disconnected from power sources during maintenance procedures;

6. Usage of additional devices and components neither provided nor recommended by the producer is

forbidden;

7. You are not allowed to use the set in high humidity environment (i.e. close to swimming pools, bath

tubs, damp basements);

8. Mounting the device in places where proper ventilation cannot be provided (e. g. closed lockers etc.)

is not recommended since it may lead to heat build-up and damaging the device itself as a

consequence;

9. Mounting the cameras on unstable surface or using not recommended mounts is forbidden.

Improperly mounted cameras may cause a fatal accident or may be seriously damaged itself. The

cameras must be mounted by qualified personnel with proper authorization, in accordance with this

user’s manual.

10. Device should be supplied only from a power sources whose parameters are in accordance with

those specified by the producer in the set technical datasheet. Therefore, it is forbidden to supply the

camera from a power sources with unknown parameters, unstable or not meeting producer’s

requirements;

Due to the product being constantly enhanced and optimized, certain parameters and functions

described in the manual in question may change without further notice.

We strongly suggest visiting the www.novuscctv.com website in order to access the newest manual

NV-WIFISET-1 - User’s manual (short form) ver 1.2

4

TABLE OF CONTENTS ..................................................................................................... 4

1. GENERAL INFORMATION ....................................................................................... ..5

1.1. Package contents .................................................................................................. 5

1.2. First start .......................................................................................................... ...5

1.3. Information about the operation of the set ....................................................... ...5

1.4. Potential sources of interferences ..................................................................... ...6

2. CAMERA - FOREWORD INFORMATION ................................................................ 9

2.1. General characteristics ......................................................................................... 9

2.2. Technical specification ...................................................................................... 10

2.3. Camera dimensions ............................................................................................ 11

2.4. Description of connectors .................................................................................. 11

2.5. Camera mounting .............................................................................................. 12

3. NVR - FOREWORD INFORMATION ....................................................................... 14

3.1. General characteristics ....................................................................................... 14

3.2. Technical specification ....................................................................................... 15

4. STARTING THE DEVICE ........................................................................................... 17

4.1. Electrical connection and other rear panel elements.. ........................................ 17

4.2. Description of the front panel ............................................................................. 17

4.3. Connecting the power supply. ............................................................................ 18

4.4. Connecting monitor. ........................................................................................... 18

4.5. Connecting ethernet and IP cameras. ................................................................. 18

4.6. Security recommendations for network architecture and configuration . .......... 19

5. NVR OPERATING ...................................................................................................... 20

5.1. Controlling via IR remote controller . ................................................................ 20

5.1. Controlling via USB mouse ............................................................................... 20

5.1. First Launch Wizard. .......................................................................................... 21

6. MAIN SCREEN ........................................................................................................... 27

7. PAIRING OF CAMERAS ........................................................................................... 29

8. REMOTE ACCESS - MOBILE APPLICATION ..................................................... 29

TABLE OF CONTENTS

NV-WIFISET-1 - User’s manual (short form) ver 1.2

5

1. FOREWORD INFORMATION

1.1. Package contents

After you open the package make sure that the following elements are inside:

• Wi-Fi cameras - 4 pcs

• Wi-Fi antennas for cameras - 4 pcs

• Power supplies for Wi-Fi cameras - 4 pcs

• Network Video Recorder (NVR) with mounted hard disk - 1pc

• Wi-Fi NVR antennas - 2 pcs

• NVR power supply - 1 pc

• Remote control - 1 pc

• Computer mouse - 1 pc

• HDMI cable for the monitor - 1 pc

• LAN network cable with RJ45 plugs - 1 pc

• Accessories bag

• Short version of user’s manual

If any of this elements has been damaged during transport, pack all the elements back into the original

box and contact your supplier for further assistance.

1.2. First start

At the first start, the connection between the cameras and the NVR takes place automatically, after

connecting the power supply - the system is immediately ready for operation. If it is necessary to change

the channel to which the given camera is assigned, follow the instructions in section 7. PAIRING OF

CAMERAS on page 29.

1.3. Information about the operation of the set

The cameras and the NVR uses wireless transmission of the image in the Wi-Fi network. These devices

work in the 802.1b/g/n standard in the 2.4GHz band and use special protocols that ensure high

transmission quality, immunity to interference and security. Thanks to the use of special transmission

protocols, it is not possible to directly connect to cameras or the NVR via a Wi-Fi network. Cameras

and recorder connect only directly to each other, therefore it is not possible to use repeaters and Wi-Fi

signal amplifiers.

The transmission protocols used are specially developed for streaming video over a Wi-Fi network.

Thanks to this, it is possible to obtain a smooth image in high resolution even in the presence of

disturbances. The priority is to maintain the connection, so the protocol reacts in an adaptive way to the

presence of disturbances in the vicinity of the cameras and the NVR and adjusts the degree of image

compression and the number of frames so that the connection between the camera and the NVR is

maintained for as long as possible. However, after exceeding the specified level of interference, the

connection may be broken - then the devices monitor the environment and after the interference

decreases or disappear, the connection is automatically established - the user does not have to perform

any actions for this purpose.

GENERAL INFORMATION

It is advisable to perform the first run before installing the cameras in the target points - to check

the correctness of the operation and familiarize yourself with the kit.

This instruction manual contains basic information about the devices, connection and

configuration of the set. A full user guide is available at www.novuscctv.com/en

NV-WIFISET-1 - User’s manual (short form) ver 1.2

6

1.4. Potential sources of interference

The use of wireless Wi-Fi transmission in the NOVUS Kit brings many benefits: it provides easier,

faster and more flexible in the choice of location installation of cameras, reduces costs and workload,

allows installation in places where it is not possible to lay cables. However, wireless communication

using radio waves is also subject to certain limitations, therefore, when assembling the Kit, for the best

results, please use the following tips:

Obstacles that block wireless communication

The location of the Kit's devices and building construction materials may affect the performance of the

Wi-Fi network. If possible, avoid obstacles or reposition devices to get a better signal.

Examples:

• The NVR is in a metal cabinet. The connection with the cameras is unstable or it can not be

established: the metal construction can isolate the cameras from the NVR. The connection of

devices may fail.

• The NVR is on the ground floor and the cameras on the floor. The material between floors is

concrete reinforced with metal rods. The floor can partially or completely block the Wi-Fi signal.

Network performance or signal strength may be low, you may not even be able to connect.

Some items reflecting and absorbing radio waves:

Reducing the impact of interference caused by other wireless devices

If there are many wireless devices near the Set, you may need to adjust the channels used by Wi-Fi

devices.

Mutual interference of Wi-Fi networks can be minimized using the following methods:

• Change the channels used in the wireless network as far away from each other. In the NVR in the

Settings -> Channels menu, and in other Wi-Fi devices according to their user manual.

• Connection of other Wi-Fi devices to a wireless network operating in the 5 GHz band (if

possible).

• Close-up of the NVR and cameras (if possible).

GENERAL INFORMATION

Type of obstacle

Degree of potential interference

Wood Low

Synthetic material Low

Glass Low

Water Medium

Bricks Medium

Marble Medium

Plaster High

Concrete High

Bullet-proof glass High

Metal Very High

NV-WIFISET-1 - User’s manual (short form) ver 1.2

7

Other sources of interference

The following items and devices may interfere with Wi-Fi connections if they are nearby. Avoid

placing the NVR or cameras near them:

• Microwave ovens

Using a microwave near the NVR may cause interference.

• Satellite television receivers

Coaxial cables and connectors used with some types of satellite dishes can cause interference. Check

the wiring for any damage that may cause radio interference (radio wave leakage). Replace the cables if

you suspect they are causing interference.

• Power sources

Some external sources of electricity, for example electric lines, railroads and transformer stations, can

cause interference. Do not put the NVR station or cameras near the wall power line or fuses.

• 2.4 GHz telephones

Cordless telephones operating in the 2.4 GHz frequency band when making calls may cause

interference to wireless devices or networks.

• Wireless video transmitters

Wireless video transmitters operating in the 2.4 GHz frequency band can cause interference to wireless

devices or networks.

• Wireless speakers

Wireless speakers operating in the 2.4 GHz frequency band can cause interference to wireless devices

or networks.

• Some external monitors and LCD displays

Some displays may cause harmonic distortion, especially in the 2.4 GHz band between channel 11 and

14. These distortions may be stronger if you use a notebook with a closed cover and an external

monitor connected.

• Poorly shielded cables

External hard drives and other devices with poorly shielded cables may cause interference to wireless

devices. If disconnecting or turning off the device helps, replace the cable that connects the device to

the computer.

• Other wireless devices

Other wireless devices operating in the 2.4 GHz band (microwave transmitters, wireless cameras, baby

monitors, neighbour's Wi-Fi device) can cause interference to Wi-Fi connections

CAUTION!

If the device was brought from a location with lower temperature, please wait until it reaches the

temperature of location it is currently in. Turning the device on immediately after bringing it

from a location with lower ambient temperature is forbidden, as the condensing water vapour

may cause short-circuits and damage the device as a result.

GENERAL INFORMATION

NVIP-2DN2003H/IR-1P-II-SET

NV-WIFISET-1 - User’s manual (short form) ver 1.2

9

2 CAMERA - FOREWORD INFORMATION

2.1. General Characteristics

• Sensor resolution: 2 megapixels

• Mechanical IR cut filter, IR operation capability

• Min. Illumination from 0 lx with IR LED on

• Wide Dynamic Range (WDR) for enhanced image quality in diverse light conditions

• Digital Noise Reduction (DNR)

• Lens type: standard, f=3.6mm/F=2.0

• Wireless connection with the NVR (Wi-Fi network)

• Built-in LED illuminator: 18 pcs LED

• Max video processing resolution: 1920 x 1080

• Power supply: 12VDC

CAMERA - FOREWORD INFORMATION

NV-WIFISET-1 - User’s manual (short form) ver 1.2

10

2.2. Technical specification

CAMERA - FOREWORD INFORMATION

IMAGE

Image Sensor 2 MPX CMOS sensor 1/2.7” SmartSens

Number of Eecve Pixels 1936 (H) x 1096 (V)

Min. Illuminaon

0.1 lx/F2.0 - color mode,

0 lx (IR on) - B/W mode

Wide Dynamic Range (WDR) yes

Digital Noise Reducon (DNR) 3D

Back Light Compensaon (BLC) yes

LENS

Lens Type standard, f=3.6 mm/F2.0

DAY/NIGHT

Switching Type mechanical IR cut lter

Switching Mode auto

Visible Light Sensor yes

NETWORK

Stream Resoluon main stream: 1920 x 1080, second stream: 640 x 360

Frame Rate 15 fps for each resoluon

Mulstreaming Mode 2 streams

Video/Audio Compression H.264/-

Number of Simultaneous Connecons max. 1

Bandwidth 2 Mb/s in total

IR LED

LED Number 18

Range 20 m

Angle 120°

INTERFACES

Network Interface Wireless (WiFi)

INSTALLATION PARAMETERS

Dimensions (mm) with bracket: 69 (Ф) x 147 (L)

Weight 0.33 kg

Degree of Protecon IP 66 (details in the user’s manual on page 12)

Enclosure

aluminium, white, fully cable managed wall mount bracket in-set

included

Power Supply 12 VDC (230 VAC/12 VDC PSU in-set included)

Power Consumpon 1.6 W, 4.3 W (IR on)

Operang Temperature -10°C ~ 50°C

NV-WIFISET-1 - User’s manual (short form) ver 1.2

11

CAMERA - FOREWORD INFORMATION

2.3. Camera dimensions

Dimensions in the drawing are given in millimeters

2.4. Description of connectors

1. Pairing button - allows to connect the camera to the NVR or to change the channel

2. Power supply 12VDC

CAUTION!

Camera power supply connector and pairing switch are not hermetic. User should seal this

connectors by himself.

2

1

NV-WIFISET-1 - User’s manual (short form) ver 1.2

12

2.5. Camera mounting

To mount a camera please follow the instructions below:

• Put the bracket to the wall in a desired mounting place (with cable hole). Taking the bracket’s

base screw holes as a pattern, mark future drilling holes for screws using a punch.

• Drill holes in accordance with previously done markings and base hole placement.

• Mount the camera with bracket on the ceiling/wall with three supplied self tapping screws.

• Loosen screws “A”.

• Adjust camera position.

• Tighten screws “A”.

WARNING!

Please note that the wall or ceiling must have enough strength to support the IP Camera.

WARNING!

In order to obtain declared degree of protection please seal the camera bracket to prevent water

getting inside. Furthermore, when installing the bracket on rough/uneven surfaces, please

additionally seal the junction with appropriate sealing mass. Please pay special attention to any

mounting holes and if they are a loop-through ones, seal them too.

WARNING!

The declared degree of protection of the camera relates to its housing and does not take into

account the possibility of moisture infiltration into the interior of the camera by connecting

cables. Connection cables protection through i.e. sealing up is the responsibility of the camera

installer. The manufacturer is not liable for any damages to the camera caused as a result of

failing in performing that activity by installer, which also means that camera damaged in that

way is not subject to warranty repairs.

CAMERA - FOREWORD INFORMATION

A

NVR-4104-H1-SET

NV-WIFISET-1 - User’s manual (short form) ver 1.2

14

NVR - FOREWORD INFORMATION

3. NVR - FOREWORD INFORMATION

3.1. Main characteristics

• Network Video Recorder, wireless with Wi-Fi transmission

• Recording resolution up to 192 x 1080

• H.264 video compression

• Dual stream recording

• Support 1 pc SATA 3,5” HDD

• Operating system based on Linux

• Main monitor 1 x HDMI (FullHD), 1 x VGA (FullHD)

• Supports up to four wireless Wi-Fi cameras (from the set)

• Backup: onto HDD or USB Flash Memory through USB port & through the network

• Software: NHDR-5000 Viewer (application for remote administration, live monitoring and recorded

data search )

• User friendly multi-lingual OSD

• IR remote control and PC mouse control (in-set included)

NV-WIFISET-1 - User’s manual (short form) ver 1.2

15

NVR - FOREWORD INFORMATION

3.2. Technical specification

* The speed of recording, displaying and playing is variable, depending on the parameters of the Wi-Fi connecon.

VIDEO

IP Cameras 4 channels at 1920 x 1080 resoluon (video)

Supported Resoluon max. 1920 x 1080

Compression H.264

Monitor Output

main (split screen, full screen, sequence): 1 x HDMI, 1 x VGA (up to 2

monitors simultaneously)

Dualstreaming Support yes

RECORDING

Recording Speed 60 fps (4 x 15 fps for 1920 x 1080 and lower)*

Stream Size 8 Mb/s in total from all cameras

Recording Mode me-lapse, triggered by: manual, moon detecon

Schedule

individual sengs for: each camera, each day of the week, conguraon

with an accuracy of: 30 min, possibility of combining individual recording

modes

Prealarm/Postalarm up to 1 s/up to 600 s

DISPLAY

Display Speed 60 fps (4 x 15 fps)*

PLAYBACK

Playback Speed 60 fps (4 x 15 fps) *

Recorded Data Search by date/me, events

BACKUP

Backup Methods USB port (HDD or Flash memory), network

Backup File Format BMP, MP4, AVI, RF

STORAGE

Internal storage built-in: 1 x HDD 3.5” 1 TB SATA

ALARM

System Reacon to Alarm Events buzzer, e-mail, screen message, recording acvaon, cloud storage

NV-WIFISET-1 - User’s manual (short form) ver 1.2

16

NVR - FOREWORD INFORMATION

NETWORK

Network Interface 1 x Ethernet - RJ-45 interface, 10/100 Mbit/s

Network Protocols Support

HTTP, TCP/IP, IPv4, UDP, FTP, DHCP, DNS, DDNS, NTP, RTSP, RTP,

UPnP, SMTP

PC/MAC Soware Internet Explorer, NHDR-5000 Viewer/Safari, NHDR-5000 Viewer

Smartphone Soware RxCamView (iPhone, Android)

Max. Number of Connecons with NVR 4

Bandwidth 32 Mb/s in total to all client workstaons

AUXILIARY INTERFACES

USB Ports 2 x USB 2.0

OPERATING SYSTEM

Operang System Linux

OSD languages: Polish, English, others

Control PC mouse and IR remote controller (in-set included), network

System Diagnosc automac control of: HDDs, camera connecon loss

Security password protecon

INSTALLATION PARAMETERS

Dimensions (mm) 360 (W) x 50 (H) x 250 (D)

Weight 1.5 kg

Power Supply 12 VDC (100 ~ 240 VAC/12 VDC PSU in-set included)

Power Consumpon 12 W (with 1 HDD)

Operang Temperature 0°C ~ 40°C

NV-WIFISET-1 - User’s manual (short form) ver 1.2

17

4. STARTING THE DEVICE

4.1. Electrical connection and other rear panel elements.

1. Wi-Fi antennas providing connectivity to cameras from the set

2. USB 2.0 port for connecting a mouse with a USB interface for navigating the recorder menu,

external hard drives, or Flash memory for copying recordings.

3. D-SUB connector for connecting the main monitor

4. HDMI connector for connecting the main monitor.

5. RJ-45 connector for connecting the local network and the Internet using an additional network

switch

6. 12VDC power socket.

4.2. Description of the front panel

1. Infrared IR receiver

2. LED (green) indicating the operation of the recorder. The lit diode means that the recorder is

running.

3. LED (red) indicating hard disk operation. Flashing of the diode means writing or reading from the

disk.

4. USB 2.0 port for connecting USB mouse, external hard drives, or Flash memory.

STARTING THE DEVICE

1

2

3

4

5

1

6

2

3

4

1

NV-WIFISET-1 - User’s manual (short form) ver 1.2

18

STARTING THE DEVICE

4.3. Connecting the power supply

Please connect provided power supply in the rear power port of the NVR.

Initialization lasts approximately 60 seconds. During this time executing any device functions and

pressing any buttons is prohibited. To shut down the device please use the menu.

CAUTION:

Make connection when the power is not applied and the power switch is turned off.

Do not place the power cord under the carpet or rug. The power cord is usually earth-grounded.

However, even if it's not earth-grounded, never modify it on your own for earth-grounding.

Make sure that power adapter is placed near of NVR and secured from accidental disconnection.

4.4. Connecting monitor

NVRs support following interfaces for main monitor: HDMI, VGA.

Following resolutions are supported: 1024x768, 1280x1024, 1440x900, 1280x720, 1920x1080.

The default screen resolution is 1280x1024 (60Hz).

Resolution changes are made in the main menu of the recorder. The change will be made after

restarting the device. If the monitor does not display the image, please wait for 20 seconds, then the

previous resolution will be restored.

Information:

When using a DVI monitor, you can use the HDMI <> DVI converter. HDMI <> DVI converter

should be purchased separately.

4.5. Connecting ethernet and IP cameras

The recorder has a 10/100 Mbit/s RJ-45 connector located on the back panel of the recorder. It enables

connection with a network switch, a computer or the Internet. Thanks to the connection to the Internet,

it is possible to access the recorder from a remote computer (via the Internet Explorer), or from a

mobile application. Remote access allows you to configure the set, view your recordings and download

them to your computer.

The details of using remote access from a computer connected to the Internet are described in the full

user manual available for download at www.novuscctv.com/en

Details of the use of remote access through a mobile application are described on page 29 of this

manual, and the broader version - in the manual of the mobile application available on the website

www.novucctv.com/en

NV-WIFISET-1 - User’s manual (short form) ver 1.2

19

STARTING THE DEVICE

4.6. Security recommendations for network architecture and configuration

WARNING!

Below are shown security recommendations for network architecture and configuration

of CCTV systems that are connected to the Internet to reduce the risk

of unauthorized interference with the system by a third party.

1. Absolutely change the default passwords and user names (if the device gives this possibility) of

all applied network devices (recorders, cameras, routers, network switches, etc.) to the

severely complexity password. Use lowercase and uppercase letters, numbers, and special characters

if there is such possibility.

2. Depending on the available functionality in the order to restrict access to the used network devices at

the administrator account level, it is recommended to configure the users accounts accordingly.

3. Do not use DMZ function (Demilitarized zone) in your router. Using that function you open the

access to recorder system from the Internet on all ports, which gives possibility for an unauthorized

interference with the system.

Instead of DMZ use port forwarding redirect only the ports which are necessary for the performance

of the connection (detailed information about ports of communication in different models of recorders,

cameras, etc. can be found in the operating instructions).

4. Use routers with firewall function and make sure it is enabled and properly configured.

5. It is recommended to change the default network communication port numbers of used devices

if there is such possibility.

6. If used network devices has a UPnP feature and it is not used, turn it off.

7. If used network devices has a P2P feature and it is not used, turn it off.

8. If used network devices support HTTPS protocol for connection, it is recommended to use it.

9. If used network devices support IP filtering for authorized connections function, it is recommended

to use it.

10. If used recorder has two network interfaces it is recommended to use both of them to physically

separate network for cameras and network for Internet connection. The only device in the system,

accessible from Internet is recorder - there is no physically access directly to any camera.

NV-WIFISET-1 - User’s manual (short form) ver 1.2

20

NVR OPERATING

5. NVR OPERATING

5.1. Controlling via IR remote controller

The set includes an IR remote controller. Its range depends on battery status and may vary between a

few and few tens of meters. Controller is supplied by two AAA batteries. Buttons functions are listed

below.

5.2. Controlling via USB mouse

It is possible to control the NVR functions using a mouse with a USB interface connected to the NVR’s

USB port. The mouse button functions are described below:

Left mouse button:

• A single click displays the channel menu and selects options from the menu

• Double-clicking on any camera in the division displays it in full screen. Double-clicking again

returns to the previous display format.

• Clicking, holding and dragging any camera in the division changes the order of the channels.

During playback - marks a part of recordings for export. When using digital zoom - changes the

position of the enlarged part of the image.

Right mouse button

• A single click on any camera displays the menu bar. When a menu or any window is displayed -

it closes.

Roll

• Turning the roll changes the amount of digital zoom.

0 - 9

Numeric buttons are used for channel selection.

ALL

Toggles between different display formats: 1 or 4

MENU

Enters to main menu. Pressing this button cancel the

selection and leaving the menu also

SUBMENU

In live mode open the Popup menu.

Navigation control „left”, „right”. In live mode open the

Popup menu.

Navigation control „up” , „down”.

SEL

Button is used for confirm the selection and start to

editing fields. In live mode open the Popup menu.

Switch on playback mode. Open Record Search menu. In

live mode open the Popup menu.

Slow down playback speed.

Fast up playback speed.

Turn on manual record.

Playback pause, press again to play frame by frame.

Stop the playback. In live mode stop the manual

recording.

Strona się ładuje...

AAT Novus NV-WIFISET-1 Instrukcja obsługi

Niniejsza instrukcja jest również odpowiednia dla

AAT Novus NV-WIFISET-1 Instrukcja obsługi

w innych językach

Powiązane artykuły

Inne dokumenty