Novus NVIP-5F-4301 (NVIP-5DN2008V/IR-1P) Instrukcja obsługi

User’ s ma n ual

(shor t for m )

NVIP-5F-4301

NVIP-5F-4301 - User’s manual (short) ver 1.0

2

IMPORTANT SAFEGUARDS AND WARNINGS

INFORMATION

EMC (2014/30/UE) and LVD (2014/35/UE) Directives

CE Marking

Our products are manufactured to comply with the requirements of the following directives and

national regulations implementing the directives:

- Electromagnetic compatibility EMC 2014/30/UE.

- Low voltage LVD 2014/35/EC with further amendment. The Directive applies to electrical

equipment designed for use with a voltage rating of between 50VAC and 1000VAC as well as

75VDC and 1500VDC.

WEEE Directive 2012/19/UE

Information on Disposal for Users of Waste Electrical and Electronic Equipment

This appliance is marked according to the European Directive on Waste Electrical and Electronic

Equipment (2012/19/UE) and further amendments. By ensuring this product is disposed of

correctly, you will help to prevent potential negative consequences for the environment and

human health, which could otherwise be caused by inappropriate waste handling of this product.

The symbol on the product, or the documents accompanying the product, indicates that this

appliance may not be treated as household waste. It shall be handed over to the applicable

collection point for used up electrical and electronic equipment for recycling purpose. For more information

about recycling of this product, please contact your local authorities, your household waste disposal service

or the shop where you purchased the product.

RoHS Directive 2011/65/UE

Information concerning the restriction of use of hazardous substances in electrical electronic

equipment.

Out of concern for human health protection and friendly environment, we assure that our products falling

under RoHS Directive regulations, regarding the restriction of the use of hazardous substances in electrical

and electronic equipment, have been designed and manufactured in compliance with the above mentioned

regulations. Simultaneously, we claim that our products have been tested and do not contain

hazardous substances whose exceeding limits could have negative impact on human health

or natural environment.

Information

The device, as a part of professional CCTV system used for surveillance and control, is not

designed for self installation in households by individuals without technical knowledge.

Excluding of responsibility in case of damaging data on a disk or other devices:

The manufacturer does not bear any responsibility in case of damaging or losing data on a disk or other

devices during device operation.

WARNING!

PRIOR TO UNDERTAKING ANY ACTION THAT IS NOT DESCRIBED FOR THE GIVEN PRODUCT

IN USER’S MANUAL AND OTHER DOCUMENTS DELIVERED WITH THE PRODUCT, OR IF IT

DOES NOT ARISE FROM THE USUAL APPLICATION OF THE PRODUCT, MANUFACTURER

MUST BE CONTACTED UNDER THE RIGOR OF EXCLUDING THE MANUFACTURER’S

RESPONSIBILITY FOR THE RESULTS OF SUCH AN ACTION.

NVIP-5F-4301 - User’s manual (short) ver 1.0

3

IMPORTANT SAFEGUARDS AND WARNINGS

WARNING!

THE KNOWLEDGE OF THIS MANUAL IS AN INDESPENSIBLE CONDITION OF A PROPER DEVICE

OPERATION. YOU ARE KINDLY REQUSTED TO FAMILIRIZE YOURSELF WITH THE MANUAL

PRIOR TO INSTALLATION AND FURTHER DEVICE OPERATION.

WARNING!

USER IS NOT ALLOWED TO DISASSEMBLE THE CASING AS THERE ARE NO USER-

SERVICEABLE PARTS INSIDE THIS UNIT. ONLY AUTHORIZED SERVICE PERSONNEL MAY OPEN

THE UNIT.

INSTALLATION AND SERVICING SHOULD ONLY BE DONE BY QUALIFIED SERVICE PERSONNEL

AND SHOULD CONFORM TO ALL LOCAL REGULATIONS.

IMPORTANT SAFEGUARDS AND WARNINGS

1. Prior to undertaking any action please consult the following manual and read all the safety and operating

instructions before starting the device.

2. Please keep this manual for the lifespan of the device in case referring to the contents of this manual is

necessary;

3. All the safety precautions referred to in this manual should be strictly followed, as they have a direct

influence on user’s safety and durability and reliability of the device;

4. All actions conducted by the servicemen and users must be accomplished in accordance with the user’s

manual;

5. The device should be disconnected from power sources during maintenance procedures;

6. Usage of additional devices and components neither provided nor recommended by the producer is forbidden;

7. Mounting the device in places where proper ventilation cannot be provided (e. g. closed lockers etc.) is not

recommended since it may lead to heat build-up and damaging the device itself as a consequence;

8. Mounting the camera on unstable surface or using not recommended mounts is forbidden. Improperly

mounted camera may cause a fatal accident or may be seriously damaged itself. The camera must be mounted

by qualified personnel with proper authorization, in accordance with this user’s manual.

9. Device should be supplied only from a power sources whose parameters are in accordance with those

specified by the producer in the camera technical datasheet. Therefore, it is forbidden to supply the camera

from a power sources with unknown parameters, unstable or not meeting producer’s requirements;

10. Signal cables (conducting TV or / and telemetric signal) should be placed in a way excluding the possibility

of damaging them by accident. Special attention must be paid to cables getting from the camera and

connecting the power supply;

11. To avoid equipment damage, whole TV circuit should be equipped with properly made discharge-, overload-

and lightning protection devices. Usage of separating transformers is advised;

12. Electric installation supplying the device should be designed to meet the specifications given by the producer

in such a way that overloading is impossible;

13. User cannot repair or upgrade the equipment himself. All maintenance actions and repairs should be

conducted only by qualified service personnel;

14. Unplug the camera from the power source immediately and contact the proper maintenance department

when the following occurs:

 Damages to the power cord or to the plug itself;

 Liquids getting inside the device or exposure to strong mechanical shock;

 Device behaves in a way not described in the manual and all adjustments approved by the

manufacturer and possible to apply by user himself, seem not to have any effect;

 Camera or its casing is damaged;

 Atypical behaviour of the camera components can be seen (heard).

15. In necessity of repairs attention to using only original replacement parts (with their parameters in

accordance with those specified by the producer) should be paid. Non-licensed service and non-genuine

replacement parts may cause fire or electrocution.

NVIP-5F-4301 - User’s manual (short) ver 1.0

4

TABLE OF CONTENTS .................................................................................................... 4

1. FOREWORD INFORMATION ................................................................................... ..5

1.1. General characteristics......................................................................................... 5

1.2. Technical specification .................................................................................... ...6

1.3. Camera dimension ........................................................................................... ...7

1.4. Package contents .............................................................................................. ...7

2. START-UP AND INITIAL IP CAMERA CONFIGURATION ................................. 8

2.1. Description of connectors .................................................................................... 8

2.2. Connecting ethernet cable ................................................................................... 8

2.3. Camera mounting ................................................................................................ 9

2.4. Starting the IP camera ....................................................................................... 10

2.5. Initial configuration via web browser ............................................................... 11

2.6. Security recommendations for network architecture and configuration .......... 12

3. NETWORK CONNECTION UTILIZING WEB BROSWER ................................ 13

3.1. Recommended PC specification for web browser ............................................. 13

3.2. Connection with IP camera via web browser ..................................................... 13

4. USING AND CONFIGURING ..................................................................................... 15

4.1. Remote Preview Interface. ................................................................................. 15

5. ELECTRIC CONNECTORS ..................................................................................... 17

5.1. Connecting power supply to the camera. .......................................................... 17

6. RESTORING FACTORY DEFAULTS .................................................................... 17

6.1. Restore factory defaults via web browser .......................................................... 17

TABLE OF CONTENTS

NVIP-5F-4301 - User’s manual (short) ver 1.0

5

1. FOREWORD INFORMATION

1.1. General Characteristics

 Sensor resolution: 6 megapixels

 Mechanical IR cut filter, IR operation capability

 Min. Illumination from 0 lx with IR LED on

 Wide Dynamic Range (WDR) for enhanced image quality in diverse light conditions

 Digital Noise Reduction (DNR)

 Lens with remote focal and focus control, f=1.1/F=2.0

 Built-in LED illuminator: 3 pcs LED

 Compression of video stream: H.264/H265

 Max video processing resolution: 2160x2160

 Multi streaming: three independently configurable streams

 Stream parameters: compression, resolution, speed and quality defined individually for each

video stream

 RTP/RTSP protocol support for video transmission

 Hardware motion detection

 Hardware sabotage detection (lens shade)

 Built-in webserver: camera configuration through the website

 Responses to alarm events: e-mail with attachment, saving file on FTP server

 Four privacy zones

 Eight definable Region of Interest

 Power supply: 12VDC, PoE (Power over Ethernet 802.3af)

As the product is constantly improved and optimized, some of the parameters and functions described

in the attached manual may have changed.

Please read the latest short form user manual found at www.novuscctv.com/en

The website www.novuscctv.com/en also contains the full version of the user manual.

Information!

The manufacturer reserves the right to printing errors and technical specifications changes

without prior notice.

FOREWORD INFORMATION

NVIP-5F-4301 - User’s manual (short) ver 1.0

6

1.2. Technical specification

FOREWORD INFORMATION

Image

Image Sensor 6 MPX CMOS sensor 1/2.9” SONY Exmor R STARVIS

Number of Eecve Pixels 3096 (H) x 2202 (V)

Min. Illuminaon

0.03 lx/F2.0 - color mode (DSS),

0 lx (IR on) - B/W mode

Electronic Shuer auto/manual: 1/5 s ~ 1/20000 s

Digital Slow Shuer (DSS) up to 1/5 s

Wide Dynamic Range (WDR) yes

Digital Noise Reducon (DNR) 2D, 3D

Defog Funcon (F-DNR) yes

Back Light Compensaon (BLC) yes

Lens

Lens Type sheye, f=1.1 mm/F2.0

Day/Night

Switching Type mechanical IR cut lter

Switching Mode auto, manual

Switching Delay 1 ~ 36 s

Visible Light Sensor yes

Network

Stream Resoluon 2160 x 2160, 1520 x 1520, 1080 x 1080, 720 x 720

Frame Rate

15 fps for 2160 x 2160,

30 fps for 1520 x 1520 and lower resoluons

Mulstreaming Mode 3 streams

Video/Audio Compression H.264, H.265/-

Number of Simultaneous Connecons max. 10

Bandwidth 16 Mb/s in total

Network Protocols Support

HTTP, TCP/IP, IPv4, HTTPS, FTP, DHCP, DNS, DDNS, NTP, RTSP, RTP,

UPnP, PPPoE, SMTP

ONVIF Protocol Support Prole S

Camera Conguraon

from Internet Explorer browser

languages: Polish, English, Russian, and others

Compable Soware NMS

Other funcons

Privacy Zones 4

Moon Detecon yes

System Reacon to Alarm Events e-mail with aachment, saving le on FTP server

IR LED

LED Number 3

Range 5 m

Angle 120°

NVIP-5F-4301 - User’s manual (short) ver 1.0

7

FOREWORD INFORMATION

1.3. Camera dimensions

Dimensions are given in millimeters

1.4. Package contents

After you open the package make sure that the following elements are inside:

 IP camera

 Accessories bag

 Short version of user’s manual

CAUTION!

If the device was brought from a location with lower temperature, please wait until it reaches

the temperature of location it is currently in. Turning the device on immediately after bringing it

from a location with lower ambient temperature is forbidden, as the condensing water vapour

may cause short-circuits and damage the device as a result.

Before starting the device familiarize yourself with the description and the role of particular

inputs, outputs and adjusting elements that the device is equipped with.

Interfaces

Network Interface 1 x Ethernet - RJ-45 interface, 10/100 Mbit/s

Installaon parameters

Dimensions (mm) 68 (Ф) x 77 (H)

Weight 0.27 kg

Degree of Protecon IP 66 (details in the user’s manual on page 10)

Enclosure vandalproof aluminium, white

Power Supply PoE, 12 VDC

Power Consumpon 4.5 W, 8 W (IR on)

Operang Temperature -30°C ~ 55°C

NVIP-5F-4301 - User’s manual (short) ver 1.0

8

1

2

START-UP AND INITIAL IP CAMERA CONFIGURATION

2. START-UP AND INITIAL CAMERA CONFIGURATION

2.1. Description of connectors

1. Power supply 12VDC

2. 100 Mb/s Ethernet port (RJ-45 hermetic connector)

WARNING!

It is forbidden to use – as the camera power source – PoE equipment (adapters, etc.) not

compatible with IEEE 802.3af standard (items called “passive PoE power supply”). Damages

that results from the usage of improper power supply source are not covered by the warranty.

2.3. Connecting ethernet cable

To maintain tightness of ethernet cable connection, please follow instruction below:

1. Unscrew the nut (b) from the connector cover (a), mount the sealing ring on the socket (c)

2. Route the network cable through the components (a) and (b). Plug the RJ-45 connector into the

socket (c)

3. Screw the connector cover (a) on the socket (c). Inside the upper part of the connector cover (a)

push in to the stop the seal of the cable (d) - the seal is cut to insert on the network cable.

4. Tighten up to the stop nut (b)

WARNING!

Other connectors and sockets, outside of the RJ-45 socket, are not hermetically sealed. User

should seal this connector by himself.

b a

b

a

c

d

NVIP-5F-4301 - User’s manual (short) ver 1.0

9

START-UP AND INITIAL IP CAMERA CONFIGURATION

2.4. Camera mounting

To mount a camera please follow the instructions below:

 Put mounting drawing paper to the wall or ceiling and mark drill holes.

 Drill holes for screws and for video and power cables.

 Using mounting screws from the package, attach the base of camera to the ceiling/wall

 Put video and power cables through a base of camera and a previously drilled hole in the wall/

ceiling.

 Push the camera to the base and then turn to the left to snap the camera into the base

WARNING!

Please note that the wall or ceiling must have enough strength to support the IP Camera.

WARNING!

In order to obtain declared degree of protection please seal the camera bracket to prevent water

getting inside. Furthermore, when installing the bracket on rough/uneven surfaces, please

additionally seal the junction with appropriate sealing mass. Please pay special attention to any

mounting holes and if they are a loop-through ones, seal them too.

WARNING!

The declared degree of protection of the camera relates to its housing and does not take into

account the possibility of moisture infiltration into the interior of the camera by connecting

cables. Connection cables protection through i.e. sealing up is the responsibility of the camera

installer. The manufacturer is not liable for any damages to the camera caused as a result of

failing in performing that activity by installer, which also means that camera damaged in that

way is not subject to warranty repairs.

NVIP-5F-4301 - User’s manual (short) ver 1.0

10

START-UP AND INITIAL CAMERA CONFIGURATION

2.5. Starting the IP camera

To run NOVUS IP camera you have to connect ethernet cable between camera and network switch.

To power it up you can connect it directly via power supply adapter with parameters compatible with

camera power supply specification, or camera can be powered with PoE (IEEE 802.3af ) compatible

switch.

After connecting power supply it takes about 30 seconds to start camera. Then You can proceed to

connect to the camera via web browser.

The recommended way to start an IP camera and perform its configuration is a connection directly

to the network switch which is not connected to other devices. To obtain further information about

network configuration parameters (IP address, gateway, network mask, etc.) please contact your

network administrator.

 Connection utilising network switch with PoE support

 Connection utilising external power supply and network switch

Network transmission

Network switch

Computer

IP camera

Computer

IP camera

Power supply and network

transmission

Network transmission

Network PoE switch

NVIP-5F-4301 - User’s manual (short) ver 1.0

11

START-UP AND INITIAL CAMERA CONFIGURATION

 Connection utilising external power supply directly to the computer

2.6. Initial configuration via the web browser

The default network settings for camera are:

1. IP address= 192.168.1.200

2. Network mask - 255.255.255.0

3. Gateway - 192.168.1.1

4. User name - root

5. Password - pass

Knowing the camera’s IP address you need to appropriately set PC IP address, so the two devices can

operate in one network subnet ( e.g. for IP 192.168.1.1, appropriate address for the camera ranges from

192.168.1.2 to 192.168.1.254, for example 192.168.1.60). It is not allowed to set the same addresses for

camera and PC computer

You can either set a network configuration (IP address, gateway, net mask, etc.) of NOVUS IP camera

yourself or select DHCP mode (DHCP server is required in this method in target network) by using

web browser or by NMS software. When you use DHCP server check IP address lease and its linking

with camera MAC address to avoid changing or losing IP address during device operation or network/

DHCP server breakdown. You have to remember to use a new camera IP address after changing

network parameters.

After network setting configuration has been done, the camera can be connected to a target network.

Network transmission - cross over cable

Computer

IP Camera

NVIP-5F-4301 - User’s manual (short) ver 1.0

12

START-UP AND INITIAL CAMERA CONFIGURATION

2.7. Security recommendations for network architecture and configuration

WARNING!

Below are shown security recommendations for network architecture and configuration

of CCTV systems that are connected to the Internet to reduce the risk

of unauthorized interference with the system by a third party.

1. Absolutely change the default passwords and user names (if the device gives this possibility) of

all applied network devices (recorders, cameras, routers, network switches, etc.) to the

severely complexity password. Use lowercase and uppercase letters, numbers, and special characters

if there is such possibility.

2. Depending on the available functionality in the order to restrict access to the used network devices at

the administrator account level, it is recommended to configure the users accounts accordingly.

3. Do not use DMZ function (Demilitarized zone) in your router. Using that function you open the

access to recorder system from the Internet on all ports, which gives possibility for an unauthorized

interference with the system.

Instead of DMZ use port forwarding redirect only the ports which are necessary for the performance

of the connection (detailed information about ports of communication in different models of recorders,

cameras, etc. can be found in the operating instructions).

4. Use routers with firewall function and make sure it is enabled and properly configured.

5. It is recommended to change the default network communication port numbers of used devices

if there is such possibility.

6. If used network devices has a UPnP feature and it is not used, turn it off.

7. If used network devices has a P2P feature and it is not used, turn it off.

8. If used network devices support HTTPS protocol for connection, it is recommended to use it.

9. If used network devices support IP filtering for authorized connections function, it is recommended

to use it.

10. If used recorder has two network interfaces it is recommended to use both of them to physically

separate network for cameras and network for Internet connection. The only device in the system,

accessible from Internet will be recorder - there will be no physically access directly to any camera.

NVIP-5F-4301 - User’s manual (short) ver 1.0

13

NETWORK CONNECTION UTILIZING WEB BROWSER

3. NETWORK CONNECTION USING WEB BROSWER

3.1. Recommended PC specification for web browser connections

Requirements below apply to connection with an IP camera, assuming smooth image display in

3000x3000 resolution and 30 fps speed.

1. CPU Intel Core i3 3GHz or newer

2. RAM Memor y min. 4 GB

3. Graphic card NVIDIA GeForce 1 GHz

4. OS Windows VISTA / 7 / 8

5. Network card 10/100/1000 Mb/s

3.2. Connection with IP camera via web browser

You have to enter camera IP address in the address bar. When you connect to the camera, web browser

will download the applet for displaying images from the camera. In Internet Explorer before the first

logon you need to install "SurveillancePlugin.exe” addition. To do this, please click on the link

"Download" and when you get the download window, click "Run" button.

When the addition installer window appears, temporarily close the browser and click "Install" button.

After installation, launch a web browser and connect to the camera.

NVIP-5F-4301 - User’s manual (short) ver 1.0

14

If the installation fails, changing security settings for the IE browser is required. In order to do that,

please choose: Tools > Internet options > Security tab > Custom level and:

 Under Download unsigned A ctiveX controls - select either Enable or Prompt

 Under Initialize and script A ctiveX controls not marked as safe - select Enable or Prompt

You can also add the camera’s IP address to “trusted zone” and set lowest security level for it.

In addition, when working in Windows Vista/7/8 the ActiveX applet may be blocked by Windows

Defender or User account control. In such case you should allow to run this applet, or simply disable

these functions.

When the addition is installed it will be possible to log into the camera. On the login page, enter your

login information. Here can also change the language of the camera interface can be maid.

For safety reasons, we recommend to change the default password and user name.

NETWORK CONNECTION UTILIZING WEB BROWSER

NVIP-5F-4301 - User’s manual (short) ver 1.0

15

USING AND CONFIGURING

4. USING AND CONFIGURING

4.1. The Remote Preview Interface

1. Icon that enables the image display options panel:

USING AND CONFIGURING

8.

"Mount type" - icons for determining the way of

mounting the camera. The right choice affects the

selection of image geometry correction and

allows to display it with as little distortion as

possible

"Display mode" - icons for choosing how to

display the image. The type and number of

available display options depends on the chosen

installation location.

4.

5.

3.

1. 2.

6.

7.

NVIP-5F-4301 - User’s manual (short) ver 1.0

16

2. The selection buttons to select the stream to be displayed in the Remote Preview window.

3. Buttons for selecting the operating mode and configure the camera:

Live - enables preview live stream

Playback - displays the playback panel

Remote Setting - displays the configuration panel camera

Local Setting - displays the configuration panel of paths to snapshots folders

4. Icon to access to the camera:

5. Icon to enable/disable panel to set the image parameters:

6. Icons for selecting the operating mode

7. Icons icons that control additional functions

USING AND CONFIGURING

The panel is able to adjust the hue,

brightness, contrast, color saturation and

sharpness (clarity).

- enables the display of the video stream

- disables the display of the video stream

- sets full screen

- enables and disables the record a video stream on your computer

- performs a screenshot and saves on your computer

- enables and disables the volume control options

- enables and disables audio transmission

- displays information about the logged in user and the version of the applet

- logout from the camera

NVIP-5F-4301 - User’s manual (short) ver 1.0

17

ELECTRIC CONNECTORS AND RESTORING FACTORY DEFAULTS

8. Live Preview window.

Double-clicking on the live view window enables the display of the image on the full screen.

Additionally, depending on the display mode selected previously (see point 1), it is possible to modify

the display method: rotation, selection of the field of view, zooming (virtual PTZ). These operations are

carried out using the mouse, by pressing and holding the left key and dragging the mouse.

5. ELECTRIC CONNECTORS

5.1. Connecting power supply to the camera.

Camera can be supplied using external power supply unit corresponding with the camera parameters or

by using RJ45 network socket and PoE (802.3af) power supply unit.

Information:

Power supply adapter is not included. Please use power adapter with parameters specified in user’s

manual.

WARNING!

It is forbidden to use – as the camera power source – PoE equipment (adapters, etc.) not

compatible with IEEE 802.3af standard (items called “passive PoE power supply”). Damages that

results from the usage of improper power supply source are not covered by the warranty.

WARNING!

In order to provide protection against voltage surges/lightning strikes, usage of appropriate surge

protectors is advised. Any damages resulting from surges are not eligible for service repairs.

6. RESTORING FACTORY DEFAULTS

6.1. Software restore to factory defaults

Camera allows you to reset your settings to the factory values. To restore the camera settings to the

default, go to the "Load Default" tab (Remote Setting -> Advanced -> Load Default). Then select

options and functions of the camera whose settings are to be reset and press the "Save" button.

After about 30 seconds, you can reconnect to the camera (at the current IP address, as long as it was not

reset network settings or on the default IP address).

Note: To make a software restore factory settings, you must be logged in as "root".

04.06.2019 JZ TF v1.0

AAT Holding S.A.

431 Pulawska St., 02-801 Warsaw, Poland

tel.: +4822 546 07 00, fax: +4822 546 07 59

www.novuscctv.com

instr ukcj a obsł ugi

(skró c ona)

NVIP-5F-4301

NVIP-5F-4301 - Skrócona instrukcja obsługi wer. 1.0

2

UWAGI I OSTRZEŻENIA

Dyrektywy EMC (2014/30/UE) i LVD (2014/35/UE)

Oznakowanie CE

Nasze produkty spełniają wymagania zawarte w dyrektywach oraz przepisach krajowych

wprowadzających dyrektywy:

Kompatybilność elektromagnetyczna EMC 2014/30/UE.

Niskonapięciowa LVD 2014/35/UE. Dyrektywa ma zastosowanie do sprzętu

elektrycznego przeznaczonego do użytkowania przy napięciu nominalnym od 50VAC do

1000VAC oraz od 75VDC do 1500VDC.

Dyrektywa WEEE 2012/19/UE

Informacja dla użytkowników o pozbywaniu się urządzeń elektrycznych i elektronicznych

Niniejszy produkt został oznakowany zgodnie z Dyrektywą WEEE (2012/65/UE) oraz późniejszymi

zmianami, dotyczącą zużytego sprzętu elektrycznego

i elektronicznego. Zapewniając prawidłowe złomowanie przyczyniają się Państwo

do ograniczenia ryzyka wystąpienia negatywnego wpływu produktu na środowisko i

zdrowie ludzi, które mogłoby zaistnieć w przypadku niewłaściwej utylizacji urządzenia.

Symbol umieszczony na produkcie lub dołączonych do niego dokumentach oznacza,

że nasz produkt nie jest klasyfikowany jako odpad z gospodarstwa domowego. Urządzenie należy

oddać do odpowiedniego punktu utylizacji odpadów w celu recyklingu. Aby uzyskać dodatkowe

informacje dotyczące recyklingu niniejszego produktu należy skontaktować się

z przedstawicielem władz lokalnych, dostawcą usług utylizacji odpadów lub sklepem, gdzie nabyto

produkt.

Dyrektywa RoHS 2011/65/UE

Informacja dla użytkowników dotycząca ograniczenia użycia substancji niebezpiecznych w

sprzęcie elektrycznym elektronicznym.

W trosce o ochronę zdrowia ludzi oraz przyjazne środowisko zapewniamy, że nasze produkty

podlegające przepisom dyrektywy RoHS, dotyczącej użycia substancji niebezpiecznych w sprzęcie

elektrycznym i elektronicznym, zostały zaprojektowane i wyprodukowane zgodnie z

wymaganiami tej dyrektywy. Jednocześnie zapewniamy, że nasze produkty zostały

przetestowane i nie zawierają substancji niebezpiecznych w ilościach mogących

niekorzystnie wpływać na zdrowie człowieka lub środowisko naturalne.

Informacja

Urządzenie, jako element profesjonalnego systemu telewizji dozorowej służącego do nadzoru

i kontroli, nie jest przeznaczone do samodzielnego montażu w gospodarstwach domowych przez osoby

nie posiadające specjalistycznej wiedzy.

Wyłączenie odpowiedzialności w przypadku uszkodzenia danych zawartych na dysku lub innych

urządzeniach:

Producent nie ponosi odpowiedzialności w razie uszkodzenia lub utraty w trakcie eksploatacji Produktu

danych zawartych na dyskach lub innych urządzeniach.

Obowiązek konsultowania się z Producentem przed wykonaniem czynności nieprzewidzianej

instrukcją obsługi albo innymi dokumentami:

Przed wykonaniem czynności, która nie jest przewidziana dla danego Produktu w instrukcji obsługi,

innych dokumentach dołączonych do Produktu lub nie wynika ze zwykłego przeznaczenia Produktu,

należy, pod rygorem wyłączenia odpowiedzialności Producenta za następstwa takiej czynności,

skontaktować się z Producentem.

Strona jest ładowana ...

Novus NVIP-5F-4301 (NVIP-5DN2008V/IR-1P) Instrukcja obsługi

Novus NVIP-5F-4301 (NVIP-5DN2008V/IR-1P) Instrukcja obsługi

w innych językach

Powiązane dokumenty