AMP Lighting VAC-ZWM1-BBZ Installation & Maintenance Manual

Marka: AMP Lighting

Model: VAC-ZWM1-BBZ

Typ: Installation & Maintenance Manual

INSTALLATION & MAINTENANCE GUIDE

Help Hotline:

1-813-978-3900 • Mon-Fri 9am-6pm (EST)

www.amplighting.com

AMP

Low Voltage Landscape Lighting

AMP

Built-In Hub Base with Stake Mount

VAC-ZWM1-BBZ

AMP

Built-In Hub Base with Stake Mount

VAC-ZWM1-BBZ

INSTALLATION & MAINTENANCE GUIDE

www.amplighting.com

–2–

Important Safety Instructions: Read Before Installation

This luminaire is intended for installation in accordance with local codes

and the National Electric Code (NEC). Failure to adhere to these codes and

instructions may result in serious injury, property damage and void the

warranty.

These instructions do not intend to cover all variations in installation,

operation maintenance or mounting situations.

1. Make sure the power is turned OFF before installing or servicing this

luminaire.

2. WARNING: risk of electrical shock. Install all luminaires 10 feet (3.05M)

or more from pool, spa or fountain.

3. This luminaire is intended to be used only with a power supply

(transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.

4. Wiring connections must be made with UL listed wire connectors that are

suitable for outdoor use.

5. Position the low voltage wire and wire connector so that it is located

within 6 inches (15.2 cm) from a building structure, a luminaire or

tting.

6. The main low voltage cable is intended for shallow burial - less than 6

inches (152 mm).

Important Safety Instructions

INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS

Lighted lamp is HOT!

WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.

1. Turn off/unplug and allow to cool before replacing lamp.

2. Lamp gets HOT quickly! Contact only switch/plug when turning on.

3. Do not touch the hot lens, guard or enclosure.

4. Keep lamp away from materials that may burn.

5. Do not touch lamp at any time. Use a soft cloth. Oil from skin may

damage lamp.

6. Do not operate the luminaire tting with a missing or damaged shield.

SAVE THESE INSTRUCTIONS

[email protected] • 813.978.3900

Product Dimensions

–3–

Main low voltage cable

Main low voltage cable shall be sized as one of the following:

A. Underground low energy circuit cable

B. SPT-3 or SPT-2W

C. Any junior hard service cord specied in 24.3.1.2

D. Any other wire rated as sunlight resistant, suitable for wet locations, and

intended for direct burial as dened in the Standard for Thermoplastic-Insulat-

ed Underground Feeder and Branch-Circuit Cables, UL 493.

Fixture low voltage cable

Fixture low voltage cable used to connect the luminaire or tting to the main

low voltage cable shall be one of the following:

A. Any wire suitable for the main voltage cable, per 53.3.1

B. SPT-1(W)

C. XTW or CXTW, or

D. AWM with equivalent properties.

2.89”

2”

2.83”

Separate Built-In Hub Top

Built-In Hub

To p

Stake Mount

Loosen the built-in hub top and

separate the built-in hub top from

the stake mount.

INSTALLATION & MAINTENANCE GUIDE

–4–

www.amplighting.com

–4–

AMP

Built-In Hub Base with Stake Mount

VAC-ZWM1-BBZ

Install Fixture to Built-In Hub Top

Wire Connection

Fixture

Built-In Hub Top

Supply Wires

Pass the supply wires from the xture

through the built-in hub top. Thread

the xture onto the built-in hub top

and hand tighten until snug.

Insert the main supply wire continuation (if needed) and the main

supply wire up through the bottom of the stake mount and strip the

ends of both sets of supply wires.

Attach the xture wires and both sets of the main supply wires to their

correct connectors in the built-in hub top.

Once the wires are installed properly, thread the built-in hub top back

onto the stake mount and hand tighten until snug.

Built-In

Hub Top

Connector

Stake Mount

Main Supply Wire

Fixture Supply

Wire

Main Supply Wire

Continuation

Fixture Wire

Main Wire

Main Wire Continuation

Main Wire

Continuation

[email protected] • 813.978.3900

–5–

INSTALLATION & MAINTENANCE GUIDE

AMP

Built-In Hub Base with Stake Mount

VAC-ZWM1-BBZ

Install Stake

Install Stake Mount

Determine the desired location

for mounting the stake mount.

Hammer the stake into the

ground until ange of stake is

ush to grade. To avoid damage

to the stake, place a board on top

of the stake while hammering.

Note: If the ground is hard and

the stake is difcult to install,

make a crosscut in the ground

using a at shovel.

Board

Ground

Soil

Stake

Clear away an area in the ground

at the wireway slot on top of

the stake. Lay the supply wires

into the wireway slot and screw

the stake mount on to the stake.

Tighten until snug.

Stake Mount

Ground

Supply Wires

Wireway Slot

Soil

Stake

INSTALLATION & MAINTENANCE GUIDE

–6–

www.amplighting.com

–6–

AMP

Built-In Hub Base with Stake Mount

VAC-ZWM1-BBZ

–6––6–

[email protected] • 813.978.3900

–7–

IS-VAC-ZWM1A-BBZ-ver1.pdf

Specications and product details subject to change without notice.

[email protected] • 813.978.3900

Help Hotline:

1-813-978-3900 • Mon-Fri 9am-6pm (EST)

www.amplighting.com

AMP Lighting VAC-ZWM1-BBZ Installation & Maintenance Manual

Marka: AMP Lighting

Model: VAC-ZWM1-BBZ

Typ: Installation & Maintenance Manual

ściągnij PDF

raport

w innych językach

English: AMP Lighting VAC-ZWM1-BBZ

AMP Lighting VAC-ZWM1-BBZ Installation & Maintenance Manual

AMP Lighting VAC-ZWM1-BBZ Installation & Maintenance Manual

w innych językach

Powiązane dokumenty