Super Bright LEDS HBUD2-50K100D-C2 Instrukcja obsługi
- Kategoria
- Akcesoria motocyklowe
- Typ
- Instrukcja obsługi
LED High Bay Light
Important: Read all instructions prior to installation. HBUD2 Series
4400 Earth City Expy, St. Louis, MO 63045 866-590-3533 superbrightleds.com
Rev Date: V1 01/20/2022
User Manual
5yr
Optional Accessories
Eye Bolt/Hook Installation Instructions
U-Bracket Installation Instructions
Safety and Notes
Environmental Specications
Operating Temperature -22°–122° F(-30°–50° C)
IP Rating IP65
• Product should be installed and serviced by a certied electrician in accordance
with applicable national, state, and local building and electrical codes.
• To reduce the risk of electric shock, ensure that the main power source and
circuit breakers are switched o before performing any installation or wiring
procedures.
• Avoid looking directly into lamp when illuminated.
• Ensure all mounts are securely attached and will support the weight of the
xture. Failure to properly support xture may result in damage or injury, for
which the manufacturer does not assume responsibility.
Specications
HBUD2-50K100D-C2
Check product label for specific electrical
specifications related to installation.
Improper installation will void warranty.
Wiring Diagram
Line
Neutral
Ground
Black / Brown
L L
N N
GND GND
White / Blue
Dim (+)
Dim (-)
Purple
+ +
- -
Gray / Pink
12 VDC AUX+
- -
Black / Black w/ White
12 VDC AUX-
- -
Blue / Blue w/ White
Green / Green w/ Yellow
Line
Neutral
Ground
Black / Brown
L L
N N
GND GND
White / Blue
Dim (+)
Dim (-)
Purple
+ +
- -
Gray / Pink
12 VDC AUX+
- -
Black / Black w/ White
12 VDC AUX-
- -
Blue / Blue w/ White
Green / Green w/ Yellow
120–277 VAC Input
0–10 V Dimming / AUX³
100–300 W versions
• HBUD-MS (microwave motion sensor)
• HBUD-8 (polycarbonate reector)
• HBUD-8-UB (U-bracket)
400–500 W versions
• HBUD-12-PR (polycarbonate reector)
1. Thread eye bolt / hook into hole on top of xture and tighten.
2. Hang xture securely.
3. With supply power switched o, connect wiring.
1. Secure mounting plates to xture with provided screws.
2. Attach U-bracket to mounting plate with provided screws and nuts.
3. Attach mounting bracket to desired surface.
4. Position U-bracket at desired angle and secure in place.
5. With supply power o, connect wiring.
¹300 W, 400 W, and 500 W models only
²100 W, 150 W, 200 W, and 240 W models only
³12 VDC AUX- on 300 W, 400 W, and 500 W models only
(B)
(C)
(B)
(C)
(A)(A)
1. 1.
4.
4.
2.
2.
1 2
LED High Bay Light
Important: Read all instructions prior to installation. HBUD2 Series
4400 Earth City Expy, St. Louis, MO 63045 866-590-3533 superbrightleds.com
Rev Date: V1 01/20/2022
User Manual
5yr
Polycarbonate Reector Installation Instructions
Motion Sensor Installation Instructions
1. Remove supply power prior to installation.
2. Position motion sensor and sensor junction box on opposite sides of the light and attach
using provided hardware.
3. Connect wiring according to wiring diagram below.
1. Turn xture upside down, if needed.
2. Line up the three holes on reector with three
threaded holes on the light.
3. Attach reector using provided screws.
motion
sensor
sensor
junction box
output to LED array
0-10V
dimming
wires
supply
power
Threaded holes for reflector
Threaded holes for reflector
2.
2.
1 2
¹300 W, 400 W, and 500 W models only
²100 W, 150 W, 200 W, and 240 W models only
-
1
-
2
Super Bright LEDS HBUD2-50K100D-C2 Instrukcja obsługi
- Kategoria
- Akcesoria motocyklowe
- Typ
- Instrukcja obsługi