Novus NVIP-5DN3512H/IR-1P Instrukcja obsługi

U s e r ’s m a n u a l

(sh o r t form)

NVIP-5DN3512H/IR-1P

NVIP-5DN3512H/IR-1P - User’s manual (short form) ver 1.0

2

IMPORTANT SAFEGUARDS AND WARNINGS

CE Marking

Our products are manufactured to comply with requirements of the following directives and national regulations

implementing the directives:

EMC (2004/108/EC) and LVD (2006/95/EC ) Directives

 Electromagnetic compatibility EMC 2004/108/EC.

 Low voltage LVD 2006/95/EC with further amendment. The Directive applies to electrical

equipment designed for use with a voltage rating of between 50VAC and 1000VAC as well as

75VDC and 1500VDC.

WEEE Directive 2012/19/EU

Information on Disposal for Users of Waste Electrical and Electronic Equipment

This appliance is marked according to the European 1000VAC Directive on Waste Electrical and

Electronic Equipment (2002/96/EC) and further amendments. By ensuring this product is disposed of correctly,

you will help to prevent potential negative consequences for the environment and human health, which could

otherwise be caused by inappropriate waste handling of this product.

The symbol on the product, or the documents accompanying the product, indicates that this appliance may not be

treated as household waste. It shall be handed over to the applicable collection point for used up electrical and

electronic equipment for recycling purpose. For more information about recycling of this product, please contact

your local authorities, your household waste disposal service or the shop where you purchased the product.

RoHS Directive 2011/65/EU

Out of concern for human health protection and friendly environment, we assure that our products falling under

RoHS Directive regulations, regarding the restriction of the use of hazardous substances in electrical

and electronic equipment, have been designed and manufactured in compliance with the above

mentioned regulations. Simultaneously, we claim that our products have been tested and do not

contain hazardous substances whose exceeding limits could have negative impact on human health or

natural environment

Information

The device, as a part of professional CCTV system used for surveillance and control, is not designed for self

installation in households by individuals without technical knowledge.

Excluding of responsibility in case of damaging data on a disk or other devices:

The manufacturer does not bear any responsibility in case of damaging or losing data on a disk or other devices

during device operation.

WARNING!

PRIOR TO UNDERTAKING ANY ACTION THAT IS NOT DESCRIBED FOR THE GIVEN PRODUCT IN

USER’S MANUAL AND OTHER DOCUMENTS DELIVERED WITH THE PRODUCT, OR IF IT DOES

NOT ARISE FROM THE USUAL APPLICATION OF THE PRODUCT, MANUFACTURER MUST BE

CONTACTED UNDER THE RIGOR OF EXCLUDING THE MANUFACTURER’S RESPONSIBILITY FOR

THE RESULTS OF SUCH AN ACTION.

NVIP-5DN3512H/IR-1P - User’s manual (short form) ver 1.0

3

IMPORTANT SAFEGUARDS AND WARNINGS

WARNING!

THE KNOWLEDGE OF THIS MANUAL IS AN INDESPENSIBLE CONDITION OF A PROPER

DEVICE OPERATION. YOU ARE KINDLY REQUSTED TO FAMILIRIZE YOURSELF WITH

THE MANUAL PRIOR TO INSTALLATION AND FURTHER DEVICE OPERATION.

WARNING!

USER IS NOT ALLOWED TO DISASSEMBLE THE CASING AS THERE ARE NO USER

-SERVICEABLE PARTS INSIDE THIS UNIT. ONLY AUTHORIZED SERVICE PERSONNEL

MAY OPEN THE UNIT

INSTALLATION AND SERVICING SHOULD ONLY BE DONE BY QUALIFIED SERVICE

PERSONNEL AND SHOULD CONFORM TO ALL LOCAL REGULATIONS

1. Prior to undertaking any action please consult the following manual and read all the safety and operating

instructions before starting the device.

2. Please keep this manual for the lifespan of the device in case referring to the contents of this manual is

necessary;

3. All the safety precautions referred to in this manual should be strictly followed, as they have a direct

influence on user’s safety and durability and reliability of the device;

4. All actions conducted by the servicemen and users must be accomplished in accordance with the user’s

manual;

5. The device should be disconnected from power sources during maintenance procedures;

6. Usage of additional devices and components neither provided nor recommended by the producer is

forbidden;

7. Mounting the device in places where proper ventilation cannot be provided (e. g. closed lockers etc.) is not

recommended since it may lead to heat build-up and damaging the device itself as a consequence;

8. Mounting the camera on unstable surface or using not recommended mounts is forbidden. Improperly

mounted camera may cause a fatal accident or may be seriously damaged itself. The camera must be mounted

by qualified personnel with proper authorization, in accordance with this user’s manual.

9. Device should be supplied only from a power sources whose parameters are in accordance with those

specified by the producer in the camera technical datasheet. Therefore, it is forbidden to supply the camera

from a power sources with unknown parameters, unstable or not meeting producer’s requirements;

Due to the product being constantly enhanced and optimized, certain parameters and functions

described in the manual in question may change without further notice.

We strongly suggest visiting the www.novuscctv.com website in order to access the newest full manual

NVIP-5DN3512H/IR-1P - User’s manual (short form) ver 1.0

4

TABLE OF CONTENTS ..................................................................................................... 4

1. FOREWORD INFORMATION ................................................................................... ..5

1.1. General characteristics ......................................................................................... 5

1.2. Technical specification .................................................................................... ...6

1.3. Camera dimension ........................................................................................... ...7

1.4. Package contents ............................................................................................... ...7

2. START-UP AND INITIAL IP CAMERA CONFIGURATION ................................. 8

2.1. Description of connectors and control tools ........................................................ 8

2.2. Cameras mounting ............................................................................................... 9

2.3. Starting the IP camera ........................................................................................ 10

2.4 Configure parameters using web browser……………………………………...11

3. NETWORK CONNECTION UTILIZING WEB BROSWER ................................ 12

3.1. Recommended PC specification for web browser ............................................. 12

3.2. Connection with IP camera via web browser ..................................................... 12

4. USING AND CONFIGURING ..................................................................................... 14

4.1. Remote Preview Interface. ................................................................................. 14

5. ELECTRIC CONNECTORS AND ACCESORIES ................................................. 15

5.1. Connecting power supply to the camera. .......................................................... 15

5.2. Camera control RS. ............................................................................................ 15

5.3. Connecting alarm inputs/outputs. ....................................................................... 15

5.4. SD card installation. ........................................................................................... 16

6. RESTORING FACTORY DEFAULTS ..................................................................... 17

6.1. Restoring software factory defaults .................................................................... 17

6.2. Restoring factory defaults by hardware means .................................................. 17

TABLE OF CONTENTS

NVIP-5DN3512H/IR-1P - User’s manual (short form) ver 1.0

5

WARNING!

This statement is a summary containing basic information on the operation and installation of IP

cameras. Full and the most recent version of the manual is available at the: www.novuscctv.com.

1. FOREWORD INFORMATION

1.1. General Characteristics

 Imager resolution: 5 megapixels

 Mechanical IR cut filter ,IR operation capability

 Min. Illumination from 0 lx with IR LED on

 Wide Dynamic Range (WDR) for enhanced image quality in diverse light conditions

 Digital Noise Reduction (DNR)

 Lens type: varifocal, f=3.6 ~ 10 mm/F1.5

 Built-in LED illuminator: 48 LED diodes

 Compression: H.265, H.264, MJPEG

 Max video processing resolution: 2592 x 1944

 Multi streaming: compression, resolution, speed and quality defined individually for each video

stream

 RTP/RTSP protocol support for video transmission

 Post-alarm functions

 Hardware motion detection

 Built-in webserver: camera configuration through the website

 Wide range of responses to alarm events: e-mail with attachment, saving file on FTP server

and triggering alarm output, saving file on SD card

 Software: NMS (NOVUS MANAGEMENT SYSTEM) for video recording, live monitoring,

playback and remote IP devices administration

 Power supply: 12VDC, PoE (Power over Ethernet)

FOREWORD INFORMATION

NVIP-5DN3512H/IR-1P - User’s manual (short form) ver 1.0

6

1.2. Technical specification

FOREWORD INFORMATION

Image

Image Sensor 5 MPX CMOS sensor 1/1.8”

Number of Effective Pixels 2592 (H) x 1944 (V)

Min. Illumination

0.016 lx/F1.5 - color mode,

0 lx (IR on) - B/W mode

Electronic Shutter auto/manual: 1/25 s ~ 1/100000 s

Wide Dynamic Range (WDR) yes

Digital Noise Reduction (DNR) 2D, 3D

Defog Function (F-DNR) no

Lens

Lens Type varifocal, f=3.6 ~ 10 mm/F1.5

Angle of View (H) 83.7° ~ 36.7°

Day/Night

Switching Type mechanical IR cut filter

Switching Mode auto, manual, time, light sensor

Switching Level Adjustment yes

Switching Schedule yes

Visible Light Sensor yes

Network

Stream Resolution

2592 x 1944, 2560 x 1440 (QHD), 1920 x 1080 (Full HD), 1280 x 720 (HD), 720 x 576 (D1),

352 x 288 (CIF)

Frame Rate 30 fps for 2592 x 1944 and lower resolutions

Multistreaming Mode 3 streams

Video/Audio Compression H.264, H.265, MJPEG/G.711

Number of Simultaneous Connections max. 10

Bandwidth 20 Mb/s in total

Network Protocols Support TCP/IP, UDP, FTP, DHCP, DDNS, NTP, SNTP, RTSP, PPPoE

ONVIF Protocol Support Profile S (ONVIF 2.3)

Camera Configuration

from Internet Explorer, Firefox, Chrome,

languages: Polish, English, Russian, and others

Compatible Software NMS

Other functions

Privacy Zones 4

Motion Detection yes

Region of interest (ROI) 8

Image Processing 90˚ image rotation, 180˚ image rotation, sharpening, mirror effect

Prealarm/Postalarm -/up to 120 s

System Reaction to Alarm Events e-mail with attachment, saving file on FTP server, saving file on SD card

IR LED

LED Number 48

Range 50 m

Interfaces

Video Output BNC, 1.0 Vp-p, 75 Ohm

Audio Input/Output 1 x Jack (3.5 mm)/1 x Jack (3.5 mm)

Alarm Input/Output 1 (NO/NC)/1 relay type

Network Interface 1 x Ethernet - RJ-45 interface, 10/100/1000 Mbit/s

Installation parameters

Dimensions (mm) with bracket: 87 (Ф) x 260 (L)

Weight 0.6 kg

Enclosure aluminium, white, wall mount bracket in-set included

Power Supply PoE, 12 VDC

Power Consumption

5 W,

8.5 W (IR on)

Operating Temperature -20°C ~ 50°C

Degree of Protection IP 66

NVIP-5DN3512H/IR-1P - User’s manual (short form) ver 1.0

7

FOREWORD INFORMATION

1.3. Camera dimensions

1.4. Package contents

After you open the package make sure that the following elements are inside:

 IP camera

 Accessories bag

 Short version of user’s manual

If any of this elements has been damaged during transport, pack all the elements back into the original

box and contact your supplier for further assistance.

CAUTION!

If the device was brought from a location with lower temperature, please wait until it reaches

the temperature of location it is currently in. Turning the device on immediately after bringing it

from a location with lower ambient temperature is forbidden, as the condensing water vapour

may cause short-circuits and damage the device as a result.

Before starting the device familiarize yourself with the description and the role of particular

inputs, outputs and adjusting elements that the device is equipped with.

NVIP-5DN3512H/IR-1P - User’s manual (short form) ver 1.0

8

1.4. Package contents

After you open the package make sure that the following elements are inside:

 IP camera

 230 VAC / 12 VDC power supply

 Accessories bag

 Short version of user’s manual

 CD containing manual and software

If any of this elements has been damaged during transport, pack all the elements back into the original

box and contact your supplier for further assistance.

CAUTION!

If the device was brought from a location with lower temperature, please wait until it reaches the

temperature of location it is currently in. Turning the device on immediately after bringing it

from a location with lower ambient temperature is forbidden, as the condensing water vapour

may cause short-circuits and damage the device as a result.

Before starting the device familiarize yourself with the description and the role of particular

inputs, outputs and adjusting elements that the device is equipped with.

2. START-UP AND INITIAL CAMERA CONFIGURATION

2.1 Description of connectors and control tools

1. BNC video output

2. Audio output

3. Audio input

4. Power supply 12VDC

5. 100 Mb/s Ethernet port (RJ-45 connector)

6. Alarm COM - Alarm output

7. Alarm NO - Alarm output

8. Alarm IN - Alarm input

9. Alarm GND - Alarm input

10. RS485 T+

11. RS485 T-

Internal slots:

1. SD card slot

2. Network indicator

3. Reset button

WARNING! To get access to above ports it is required to open front cover

WARNING! In order to obtain declared degree of protection please seal the camera bracket to prevent

water getting inside. Furthermore, when installing the bracket on rough/uneven surfaces, please

additionally seal the junction with appropriate sealing mass. Please pay special attention to any

mounting holes and if they are a loop-through ones, seal them too.

START-UP AND INITIAL CAMERA CONFIGURATION

1

2

4

3

5

6

7

10

9

8

11

1

2

3

4

NVIP-5DN3512H/IR-1P - User’s manual (short form) ver 1.0

9

2.2. Cameras mounting and focus adjustments

To mount a camera please follow the instructions below:

1. Drill the screw holes and the cable hole on the wall according to the drill template.

2. Route the cables to the cable hole and connect the cables.

3. Using included screws mounting base on smooth surface providing declared degree of IP protection.

4. Using allen key loosen screws 1, 2 and 3. Then adjust camera position and tight lock screws.

5.Remover sunshield and front housing and adjust zoom and focus.

6.Optionally insert SD card.

7.Mount front housing and sunshield.

WARNING! Please note that the wall or ceiling must have enough strength to support the IP Camera.

START-UP AND INITIAL CAMERA CONFIGURATION

NVIP-5DN3512H/IR-1P - User’s manual (short form) ver 1.0

10

2.4. Starting the IP camera

To run NOVUS IP camera you have to connect ethernet cable between camera and network switch.

To power it up you can connect it directly via power supply adapter with parameters compatible with

camera power supply specification, or camera can be powered with PoE (IEEE 802.3af ) compatible

switch.

After connecting power supply it takes about 30 seconds to start camera. Then You can proceed to

connect to the camera via web browser.

The recommended way to start an IP camera and perform its configuration is a connection directly

to the network switch which is not connected to other devices. To obtain further information about

network configuration parameters (IP address, gateway, network mask, etc.) please contact your

network administrator.

 Connection utilising network switch with PoE support

 Connection utilising external power supply and network switch

START-UP AND INITIAL CAMERA CONFIGURATION

IP Camera

Network transmission

Network Switch

Computer

Network transmission

Power supply and

network transmission

Computer

IP Camera

Network Switch

PoE

Network transmission

NVIP-5DN3512H/IR-1P - User’s manual (short form) ver 1.0

11

 Connection utilising external power supply directly to the computer

Information:

Power supply adapter is not included. Please use power adapter with parameters specified in user ‘s

manual.

Caution:

In order to provide protection against voltage surges/lightning strikes, usage of appropriate surge

protectors is advised. Any damages resulting from surges are not eligible for service repairs.

2.5. Initial configuration via the web browser

The default network settings for NVIP-5DN3512H/IR-1P IP camera series are :

1. IP address= 192.168.1.200

2. Network mask - 255.255.255.0

3. Gateway - 192.168.1.1

4. User name - root

5. Password - pass

Knowing the camera’s IP address you need to appropriately set PC IP address, so the two devices can

operate in one network subnet ( e.g. for IP 192.168.1.1, appropriate address for the camera ranges from

192.168.1.2 to 192.168.1.254, for example 192.168.1.60). It is not allowed to set the same addresses for

camera and PC computer

You can either set a network configuration (IP address, gateway, net mask, etc.) of NOVUS IP camera

yourself or select DHCP mode (DHCP server is required in this method in target network) by using

web browser or by NMS software. When you use DHCP server check IP address lease and its linking

with camera MAC address to avoid changing or losing IP address during device operation or network/

DHCP server breakdown. You have to remember to use a new camera IP address after changing

network parameters.

After network setting configuration has been done, the camera can be connected to a target network.

START-UP AND INITIAL CAMERA CONFIGURATION

IP Camera

Network transmission - cross over cable

Computer

NVIP-5DN3512H/IR-1P - User’s manual (short form) ver 1.0

12

3. NETWORK CONNECTION UTILIZING WEB BROSWER

3.1. Recommended PC specification for web browser connections

Requirements below apply to connection with an IP camera, assuming smooth image display

in 2592x1944 resolution and 30 fps speed.

1. CPU Intel Core i3 3 GHz or newer

2. RAM Memory min. 4 GB

3. Graphic card NVIDIA GeForce 512 MB or equivalent

4. OS Windows Windows 7 / 8 / 8.1 / 10

5. Network card 10/100/1000 Mb/s

3.2. Connection with IP camera via web browser

You have to enter camera IP address in the address bar. When you connect to the camera, web browser

will download the applet for displaying images from the camera. In Internet Explorer it may be

necessary to accept an ActiveX control. To do this, click the right mouse button on the message, select

"Install Active X control" and then click Install. After successfully SuperClientEx plug in downloading

run and install it on a computer.

NETWORK CONNECTION UTILIZING WEB BROWSER

NVIP-5DN3512H/IR-1P - User’s manual (short form) ver 1.0

13

If the installation fails, changing security settings for the IE browser is required. In order to do that,

please choose: Tools > Internet options > Security tab > Custom level and:

 Under Download unsigned ActiveX controls - select either Enable or Prompt

 Under Initialize and script ActiveX controls not marked as safe - select Enable or Prompt

You can also add the camera’s IP address to “trusted zone” and set lowest security level for it.

In addition, when working in Windows 7/ 8/ 8.1 / 10 the ActiveX applet may be blocked by Windows

Defender or User account control. In such case you should allow to run this applet, or simply disable

these functions.

After successful installation login window will be displayed. Default user is root and default password

is pass. For safety reasons, it is recommended to change default user name and password.

NETWORK CONNECTION UTILIZING WEB BROWSER

NVIP-5DN3512H/IR-1P - User’s manual (short form) ver 1.0

14

4. USING AND CONFIGURING

4.1 Remote Preview Interface

1. Motion detection

Motion detection icon changes color from white to red when motion is detected.

Alarm icon changes color from white to red when alarm situation has occured.

2. Display fluency settings

It is possible to increase video display fluency by setting video buffor (0 ~ 4 seconds).

3. Video size settings

Fix size Zoom in (digital) Full screen

Actual size Zoom out (digital)

4. Local record

Start record Snap On/Off microphone

Playback Enable / disable audio

5. PTZ

Allow user to configure zoom and focus. (lens control)

REMOTE PREVIEW

1

2 3 4

5

NVIP-5DN3512H/IR-1P - User’s manual (short form) ver 1.0

15

ELECTRIC CONNECTORS AND ACCESORIES

5. ELECTRIC CONNECTORS AND ACCESORIES

5.1. Connecting power supply to the camera.

Camera can be supplied using external power supply unit corresponding with the camera parameters or

by using RJ45 network socket and PoE (802.3at Type 1 ) power supply unit.

Information:

Power supply adapter is not included. Please use power adapter with parameters specified in user’s

manual.

Caution:

In order to provide protection against voltage surges/lightning strikes, usage of appropriate surge

protectors is advised. Any damages resulting from surges are not eligible for service repairs.

5.2. Camera control - RS-485

Function unavailable.

5.3. Connecting alarm inputs/outputs.

Alarm input

 Alarm input connection

Alarm

input (-)

Alarm GND

IP Camera

Alarm

input (+)

Alarm IN

Switch/sensor

NVIP-5DN3512H/IR-1P - User’s manual (short form) ver 1.0

16

REMOTE PREVIEW

Alarm output

Camera alarm output is an relay output type.

 Alarm output electric connections

5.4 SD card installation

Camera supports SD/SDHC cards up to a maximum size of 64GB. In order to install the card properly,

please follow the instructions below:

 Turn the camera off

 Remove front cover to get access to internal connectors

 Mount SD card, according

to the picture:

 Close front cover

 Turn the camera on

 Check the SD card by checking its capacity in the “System Config” -> “SD Card” tab.

Alarm

Output (-)

Alarm COM

Alarm

Output (+)

Alarm NO

Indicator

power

supply

Indicator

IP Camera

SD card slot

NVIP-5DN3512H/IR-1P - User’s manual (short form) ver 1.0

17

RESTORING FACTORY DEFAULTS

6. RESTORING FACTORY DEFAULTS

NOVUS IP cameras allow to restore defaults via:

 software (web browser level)

 hardware (using reset button)

6.1. Restoring factory defaults by software means

User can restore default settings of the IP camera except network settings. To restore to default settings

go to: “Advanced Config -> Config Backup & Restore” tab. Process of restoring takes about two

minutes.

6.2. Restoring factory defaults by hardware means

In order to restore factory defaults for the camera please follow the instructions:

 Remove front cover to get access to internal connectors

 Press the RESET button and hold on for 10 seconds

 Release button

 Close front cover off the camera

 Log on after approx. 30 seconds using default IP address (http://192.168.1.200) and default user

name (root) and password (pass)

RESET button

2016-03-31 JB, MK

AAT Holding S.A., ul. Puławska 431, 02-801 Warszawa, Polska

tel.: 22 546 07 00, faks: 22 546 07 59

www.novuscctv.com

Instr ukcj a obs ług i

(sk r ó cona )

NVIP-5DN3512H/IR-1P

NVIP-5DN3512H/IR-1P - Skrócona instrukcja obsługi wer. 1.0

2

UWAGI I OSTRZEŻENIA

Dyrektywy EMC (2004/108/EC) i LVD (2006/95/EC)

Oznakowanie CE

Nasze produkty spełniają wymagania zawarte w dyrektywach oraz przepisach krajowych

wprowadzających dyrektywy:

Kompatybilność elektromagnetyczna EMC 2004/108/EC.

Niskonapięciowa LVD 2006/95/EC. Dyrektywa ma zastosowanie do sprzętu elektrycznego

przeznaczonego do użytkowania przy napięciu nominalnym od 50VAC do 1000VAC oraz od 75VDC

do 1500VDC.

Dyrektywa WEEE 2012/19/UE

Informacja dla użytkowników o pozbywaniu się urządzeń elektrycznych i elektronicznych

Niniejszy produkt został oznakowany zgodnie z Dyrektywą WEEE (2002/96/EC) oraz

późniejszymi zmianami, dotyczącą zużytego sprzętu elektrycznego i elektronicznego. Zapewniając

prawidłowe złomowanie przyczyniają się Państwo do ograniczenia ryzyka wystąpienia negatywnego

wpływu produktu na środowisko i zdrowie ludzi, które mogłoby zaistnieć w przypadku niewłaściwej

utylizacji urządzenia.

Symbol umieszczony na produkcie lub dołączonych do niego dokumentach oznacza,

że nasz produkt nie jest klasyfikowany jako odpad z gospodarstwa domowego. Urządzenie należy

oddać do odpowiedniego punktu utylizacji odpadów w celu recyklingu. Aby uzyskać dodatkowe

informacje dotyczące recyklingu niniejszego produktu należy skontaktować się

z przedstawicielem władz lokalnych, dostawcą usług utylizacji odpadów lub sklepem, gdzie nabyto

produkt.

Dyrektywa RoHS 2011/65/UE

Informacja dla użytkowników dotycząca ograniczenia użycia substancji

niebezpiecznych w sprzęcie elektrycznym elektronicznym.

W trosce o ochronę zdrowia ludzi oraz przyjazne środowisko zapewniamy, że nasze produkty

podlegające przepisom dyrektywy RoHS, dotyczącej użycia substancji niebezpiecznych w sprzęcie

elektrycznym i elektronicznym, zostały zaprojektowane i wyprodukowane zgodnie z wymaganiami tej

dyrektywy. Jednocześnie zapewniamy, że nasze produkty zostały przetestowane i nie zawierają

substancji niebezpiecznych w ilościach mogących niekorzystnie wpływać na zdrowie człowieka lub

środowisko naturalne.

Informacja

Urządzenie, jako element profesjonalnego systemu telewizji dozorowej służącego do nadzoru

i kontroli, nie jest przeznaczone do samodzielnego montażu w gospodarstwach domowych przez osoby

nie posiadające specjalistycznej wiedzy.

Wyłączenie odpowiedzialności w przypadku uszkodzenia danych zawartych na dysku lub innych

urządzeniach:

Producent nie ponosi odpowiedzialności w razie uszkodzenia lub utraty w trakcie

eksploatacji Produktu danych zawartych na dyskach lub innych urządzeniach.

Obowiązek konsultowania się z Producentem przed wykonaniem czynności

nieprzewidzianej instrukcją obsługi albo innymi dokumentami:

Przed wykonaniem czynności, która nie jest przewidziana dla danego Produktu w instrukcji

obsługi, innych dokumentach dołączonych do Produktu lub nie wynika ze zwykłego

przeznaczenia Produktu, należy, pod rygorem wyłączenia odpowiedzialności Producenta za następstwa

takiej czynności, skontaktować się z Producentem.

Strona jest ładowana ...

Novus NVIP-5DN3512H/IR-1P Instrukcja obsługi

Novus NVIP-5DN3512H/IR-1P Instrukcja obsługi

w innych językach

Powiązane dokumenty