George Kovacs P8238-671-L Instrukcja obsługi

Marka: George Kovacs

Model: P8238-671-L

Typ: Instrukcja obsługi

Niniejsza instrukcja jest również odpowiednia dla

Page 1/2

INSTALLATION INSTRUCTIONS FOR P8236-671-L、P8238-671-L

P8239-671-L For LED Pendant mount

READ AND SAVE THESE INSTRUCTIONS

WARNIN G ! SH UT P OWER OFF AT FUS E OR C IRC U IT BR E AK ER

AV E R T I S S EM E N T ! CO U P E R L E C O U R A N T A U N I V E AU D E S F U S I B L E S O U D O D I S J ON C T E U

ASSEMBLING THE FIXTURE (Fig.1 )

1 Shut off power at the fuse box or circuit breaker. Remove the old fixture

including the mounting hardware.

2 Carefully remove the fixture from the carton and check that all parts are

included as show in Figure 1. Unscrew ( G ) to remove the mounting plate

( A ) from the canopy ( F).

3 Tighten the iron Rod (H) to the lamp body .

4 Position mounting plate(A) on the ceiling ,and mark the location of the dry

wall anchors(W).Pre-drill the holes for the dry wall anchors ,Insert the dry

wall anchors(W) into the ceiling ,Attach the mounting plate (A) to the

junction box using the mounting screws(B,size 8#-32N 1/2'’).The side of

the mounting plate marked “GND” must face out.Place the wood screw (T)

through the slot hole into the dry wall anchor(W) to secure the mounting

CONNECTING THE WIRES (Fig. 3)

5 Connect the electrical wire as shown in figure 2,making sure that all wire

connectors are secured. If your junction box has a ground wire (green or

bare copper), connect the ground wire from the fixture to it. Otherwise

connect fixture ground wire (C) directly to the mounting plate using the

green screw (D)provided. Tuck the wire connections neatly into the ceiling

junction box as you hold the canopy towards the ceiling.

FINISHING THE INSTALLATION (Fig.1)

6. Fix the canopy(F) into the mounting plate (A) with screw (G).Adjust the

length of the cable to pull or push until the desired length by twist release

the screw(S) ,ensure to re-tighten the set screw (S) after adjustment .

7.Fix the glass shade (J) to the lamp body (I)

Your installation is now complete. Return power to the junction box and

test the fixture.

CAUTION/ATTENTION: When handling the fixture,do not apply pressure

to the LEDs. Hold the fixture by the frame only.

IMPORTANT: Fixture should be installed by a qualified electrician to

ensure proper wiring and installation. Dimmable with ELV and/or LED

compatible wall dimmer switches

Fig.1

Fig.3

Page 2/2

INSTALLATION INSTRUCTIONS FOR P8236-671-L、P8238-671-L

P8239-671-L For Semi-flush mount

READ AND SAVE THESE INSTRUCTIONS

WARNIN G ! SH UT P OWER OFF AT FUS E OR C IRC U IT BR E AK ER

AV E R T I S S EM E N T ! CO U P E R L E C O U R A N T A U N I V E AU D E S F U S I B L E S O U D O D I S J ON C T E U

ASSEMBLING THE FIXTURE (Fig.2)

1 Shut off power at the fuse box or circuit breaker. Remove the old fixture

including the mounting hardware.

2 Carefully remove the fixture from the carton and check that all parts are

included as show in Figure 1. Unscrew ( G ) to remove the mounting plate

( A ) from the canopy ( F).

3 Disconnect the wire nut (L) , remove the “8” buckle ,unscrew the hex nut

(N) .Release the screw( S ) by the flat-philips screw driver ,pull the cable wire

from the canopy(F) ,take away the part (P) and rod (H) .

4 Repeat 3 to connect the wire ,pass the part (O) through the hole of the canopy

(F),tighten the screw (N).

5 Position mounting plate(A) on the ceiling ,and mark the location of the dry wall

anchors(W).Pre-drill the holes for the dry wall anchors ,Insert the dry wall

anchors(W) into the ceiling ,Attach the mounting plate (A) to the junction box

using the mounting screws(B,size 8#-32N 1/2'’).The side of the mounting

plate marked “GND” must face out.Place the wood screw (T) through the slot

hole into the dry wall anchor(W) to secure the mounting

CONNECTING THE WIRES (Fig. 3)

6 Connect the electrical wire as shown in figure 2,making sure that all wire

connectors are secured. If your junction box has a ground wire (green or bare

copper),connect the ground wire from the fixture to it. Otherwise connect

fixture ground wire (C) directly to the mounting plate

using the green screw (D)provided. Tuck the wire connections neatly into the

ceiling junction box as you hold the canopy towards the ceiling.

FINISHING THE INSTALLATION (Fig.1)

7. Fix the canopy(F) into the mounting plate (A) with screw (G).

8.Fix the glass shade (J) to the lamp body (I)

Your installation is now complete. Return power to the junction box and test

the fixture.

CAUTION/ATTENTION: When handling the fixture,do not apply pressure to

the LEDs. Hold the fixture by the frame only.

IMPORTANT: Fixture should be installed by a qualified electrician to ensure

proper wiring and installation. Dimmable with ELV and/or LED compatible wall

dimmer switches

LED module replace(Fig.4)

Shut off power before replacing

1:Each lamp head there have a LED module ,if any one of them does not

work ,replace the module (K) as shown in Fig.4.Make sure the power is off

when you replace .

2:Remove the glass shade (J) of no work one ,twist off the module screw ,take

off the module (K) .Save these parts for subsequent service.

3:Press the quick connector(M),pull out the wire ,replace a new module ;

4:Repeat 4-1 to assembly the fixture Your replace is now complete , Re-install

the fixture to the ceiling as shown in Fig.1,return power to the junction box

and text the fixture

Fig.2

Fig.3

Fig.4

George Kovacs P8238-671-L Instrukcja obsługi

Marka: George Kovacs

Model: P8238-671-L

Typ: Instrukcja obsługi

Niniejsza instrukcja jest również odpowiednia dla

Pobierz PDF

raport

w innych językach

English: George Kovacs P8238-671-L User manual

George Kovacs P8238-671-L Instrukcja obsługi

Niniejsza instrukcja jest również odpowiednia dla

George Kovacs P8238-671-L Instrukcja obsługi

w innych językach

Powiązane artykuły

Inne dokumenty