Novus NVIP-9F-4301 Instrukcja obsługi

User’ s ma n ual

(shor t for m )

NVIP-9F-4301

NVIP-9F-4301 - User’s manual (short) ver 1.0

2

IMPORTANT SAFEGUARDS AND WARNINGS

INFORMATION

THE PRODUCT MEETS THE REQUIREMENTS CONTAINED IN THE FOLLOWING DIRECTIVES:

This appliance is marked according to the European 1000VAC Directive on Waste Electrical and Electronic

Equipment (2012/19/EU) and further amendments. By ensuring this product is disposed of correctly, you will

help to prevent potential negative consequences for the environment and human health, which could otherwise

be caused by inappropriate waste handling of this product.

The symbol on the product, or the documents accompanying the product, indicates that this appliance may not be

treated as household waste. It shall be handed over to the applicable collection point for used up electrical and

electronic equipment for recycling purpose. For more information about recycling of this product, please contact

your local authorities, your household waste disposal service or the shop where you purchased the product.

Out of concern for human health protection and friendly environment, we assure that our products falling under

RoHS Directive regulations, regarding the restriction of the use of hazardous substances in electrical and

electronic equipment, have been designed and manufactured in compliance with the above mentioned

regulations. Simultaneously, we claim that our products have been tested and do not contain hazardous

substances whose exceeding limits could have negative impact on human health or natural environment

Information

The device, as a part of professional CCTV system used for surveillance and control, is not designed for self

installation in households by individuals without technical knowledge.

Excluding of responsibility in case of damaging data on a disk or other devices:

The manufacturer does not bear any responsibility in case of damaging or losing data on a disk or other devices

during device operation.

WARNING!

PRIOR TO UNDERTAKING ANY ACTION THAT IS NOT DESCRIBED FOR THE GIVEN PRODUCT IN

USER’S MANUAL AND OTHER DOCUMENTS DELIVERED WITH THE PRODUCT, OR IF IT DOES

NOT ARISE FROM THE USUAL APPLICATION OF THE PRODUCT, MANUFACTURER MUST BE

CONTACTED UNDER THE RIGOR OF EXCLUDING THE MANUFACTURER’S RESPONSIBILITY FOR

THE RESULTS OF SUCH AN ACTION.

DIRECTIVE 2014/30/EU OF THE EUROPEAN PARLIAMENT AND OF THE

COUNCIL of 26 February 2014 on the harmonisation of the laws of the Member

States relating to electromagnetic compatibility (OJ L 96, 29.3.2014, p. 79–106, with

DIRECTIVE 2012/19/EU OF THE EUROPEAN PARLIAMENT AND OF THE

COUNCIL of 4 July 2012 on waste electrical and electr onic equipment (WEEE)

(OJ L 197, 24.7.2012, p. 38–71, with changes)

DIRECTIVE 2011/65/EU OF THE EUROPEAN PARLIAMENT AND OF THE

COUNCIL of 8 June 2011 on the restriction of the use of certain hazardous substances

in electrical and electronic equipment (OJ L 174, 1.7.2011, p. 88–110, with changes)

NVIP-9F-4301 - User’s manual (short) ver 1.0

3

IMPORTANT SAFEGUARDS AND WARNINGS

WARNING!

THE KNOWLEDGE OF THIS MANUAL IS AN INDESPENSIBLE CONDITION OF A PROPER DEVICE

OPERATION. YOU ARE KINDLY REQUSTED TO FAMILIRIZE YOURSELF WITH THE MANUAL

PRIOR TO INSTALLATION AND FURTHER DEVICE OPERATION.

WARNING!

USER IS NOT ALLOWED TO DISASSEMBLE THE CASING AS THERE ARE NO USER-

SERVICEABLE PARTS INSIDE THIS UNIT. ONLY AUTHORIZED SERVICE PERSONNEL MAY OPEN

THE UNIT.

INSTALLATION AND SERVICING SHOULD ONLY BE DONE BY QUALIFIED SERVICE PERSONNEL

AND SHOULD CONFORM TO ALL LOCAL REGULATIONS.

IMPORTANT SAFEGUARDS AND WARNINGS

1. Prior to undertaking any action please consult the following manual and read all the safety and operating

instructions before starting the device.

2. Please keep this manual for the lifespan of the device in case referring to the contents of this manual is

necessary;

3. All the safety precautions referred to in this manual should be strictly followed, as they have a direct

influence on user’s safety and durability and reliability of the device;

4. All actions conducted by the servicemen and users must be accomplished in accordance with the user’s

manual;

5. The device should be disconnected from power sources during maintenance procedures;

6. Usage of additional devices and components neither provided nor recommended by the producer is forbidden;

7. Mounting the device in places where proper ventilation cannot be provided (e. g. closed lockers etc.) is not

recommended since it may lead to heat build-up and damaging the device itself as a consequence;

8. Mounting the camera on unstable surface or using not recommended mounts is forbidden. Improperly

mounted camera may cause a fatal accident or may be seriously damaged itself. The camera must be mounted

by qualified personnel with proper authorization, in accordance with this user’s manual.

9. Device should be supplied only from a power sources whose parameters are in accordance with those

specified by the producer in the camera technical datasheet. Therefore, it is forbidden to supply the camera

from a power sources with unknown parameters, unstable or not meeting producer’s requirements;

10. Signal cables (conducting TV or / and telemetric signal) should be placed in a way excluding the possibility

of damaging them by accident. Special attention must be paid to cables getting from the camera and

connecting the power supply;

11. To avoid equipment damage, whole TV circuit should be equipped with properly made discharge-, overload-

and lightning protection devices. Usage of separating transformers is advised;

12. Electric installation supplying the device should be designed to meet the specifications given by the producer

in such a way that overloading is impossible;

13. User cannot repair or upgrade the equipment himself. All maintenance actions and repairs should be

conducted only by qualified service personnel;

14. Unplug the camera from the power source immediately and contact the proper maintenance department

when the following occurs:

 Damages to the power cord or to the plug itself;

 Liquids getting inside the device or exposure to strong mechanical shock;

 Device behaves in a way not described in the manual and all adjustments approved by the

manufacturer and possible to apply by user himself, seem not to have any effect;

 Camera or its casing is damaged;

 Atypical behaviour of the camera components can be seen (heard).

15. In necessity of repairs attention to using only original replacement parts (with their parameters in

accordance with those specified by the producer) should be paid. Non-licensed service and non-genuine

replacement parts may cause fire or electrocution.

NVIP-9F-4301 - User’s manual (short) ver 1.0

4

TABLE OF CONTENTS .................................................................................................... 4

1. FOREWORD INFORMATION ................................................................................... ..5

1.1. General characteristics......................................................................................... 5

1.2. Technical specification .................................................................................... ...6

1.3. Camera dimension ........................................................................................... ...7

1.4. Package contents .............................................................................................. ...7

2. START-UP AND INITIAL IP CAMERA CONFIGURATION ................................. 8

2.1. Description of connectors .................................................................................... 8

2.2. Power supply connection ..................................................................................... 9

2.3. Connecting ethernet cable ................................................................................... 9

2.4. Camera mounting .............................................................................................. 10

2.5. Starting the camera ............................................................................................ 11

2.6. Initial configuration via web browser ............................................................... 12

2.7. Security recommendations for network architecture and configuration ........... 13

3. NETWORK CONNECTION UTILIZING WEB BROSWER ................................ 14

3.1. Recommended PC specification for web browser ............................................. 14

3.2. Connection with IP camera via web browser ..................................................... 14

4. USING AND CONFIGURING ..................................................................................... 16

4.1. Remote Preview Interface. ................................................................................. 16

5. ELECTRIC CONNECTORS ..................................................................................... 18

5.1. Connecting of the alarm input. ........................................................................... 18

5.2. Connecting of the alarm output .......................................................................... 18

6. RESTORING FACTORY DEFAULTS .................................................................... 18

6.1. Software factory reset ........................................................................................ 18

6.1. Hardware factory reset ...................................................................................... 18

7. INSTALLING SD CARD ............................................................................................ 19

TABLE OF CONTENTS

NVIP-9F-4301 - User’s manual (short) ver 1.0

5

1. FOREWORD INFORMATION

1.1. General Characteristics

 Sensor resolution: 12 megapixels

 Mechanical IR cut filter, IR operation capability

 Min. Illumination from 0 lx with IR LED on

 Wide Dynamic Range (WDR) for enhanced image quality in diverse light conditions

 Digital Noise Reduction (DNR)

 Lens with remote focal and focus control, f=2.0/F=2.4

 Built-in LED illuminator: 3 pcs LED

 Compression of video stream: H.264/H265

 Max video processing resolution: 3000x3000

 Multi streaming: three independently configurable streams

 Stream parameters: compression, resolution, speed and quality defined individually for each

video stream

 RTP/RTSP protocol support for video transmission

 Two-way audio transmission

 Compression of audio stream: G.711, G.726, ADPCM

 Alarm input and output

 Hardware motion detection

 Hardware sabotage detection (lens shade)

 Built-in webserver: camera configuration through the website

 Wide range of responses to alarm events: e-mail with attachment, saving file on FTP server,

activation of alarm output, recording on SD card

 Four privacy zones

 Eight definable Region of Interest

 Power supply: 12VDC, PoE (Power over Ethernet 802.3af)

As the product is constantly improved and optimized, some of the parameters and functions described

in the attached manual may have changed.

Please read the latest short form user manual found at www.novuscctv.com/en

The website www.novuscctv.com/en also contains the full version of the user manual.

Information!

The manufacturer reserves the right to printing errors and technical specifications changes

without prior notice.

FOREWORD INFORMATION

NVIP-9F-4301 - User’s manual (short) ver 1.0

6

1.2. Technical specification

FOREWORD INFORMATION

Image

Image Sensor 12 MPX CMOS sensor 1/1.7” SONY Exmor R STARVIS

Number of Eecve Pixels 4072 (H) x 3046 (V)

Min. Illuminaon

0.04 lx/F2.4 - color mode,

0 lx (IR on) - B/W mode

Electronic Shuer auto/manual: 1/5 s ~ 1/20000 s

Digital Slow Shuer (DSS) up to 1/5 s

Wide Dynamic Range (WDR) yes

Digital Noise Reducon (DNR) 2D, 3D

Defog Funcon (F-DNR) yes

Back Light Compensaon (BLC) yes

Lens

Lens Type sheye, f=2.0 mm/F2.4

Day/Night

Switching Type mechanical IR cut lter

Switching Mode auto, manual

Switching Delay 1 ~ 36 s

Visible Light Sensor yes

Network

Stream Resoluon

3000 x 3000, 2560 x 2560, 2160 x 2160, 1520 x 1520, 1080 x 1080,

720 x 720, 480 x 480

Frame Rate 30 fps for 3000 x 3000 and lower resoluons

Mulstreaming Mode 3 streams

Video/Audio Compression H.264, H.265/G.711, G.726, ADPCM

Number of Simultaneous Connecons max. 10

Bandwidth 40 Mb/s in total

Network Protocols Support

HTTP, TCP/IP, IPv4, HTTPS, FTP, DHCP, DNS, DDNS, NTP, RTSP, RTP,

UPnP, PPPoE, SMTP

ONVIF Protocol Support Prole S

Camera Conguraon

from Internet Explorer browser

languages: Polish, English, Russian, and others

Compable Soware NMS

Other funcons

Privacy Zones 4

Moon Detecon yes

Prealarm/Postalarm -/up to 300 s

System Reacon to Alarm Events

e-mail with aachment, saving le on FTP server, saving le on SD

card, alarm output acvaon

IR LED

LED Number 3

Range 10 m

Angle 120°

NVIP-9F-4301 - User’s manual (short) ver 1.0

7

FOREWORD INFORMATION

1.3. Camera dimensions

Dimensions are given in millimeters

1.4. Package contents

After you open the package make sure that the following elements are inside:

 IP camera

 Accessories bag

 Short version of user’s manual

Interfaces

Video Output BNC, 1.0 Vp-p, 75 Ohm

Audio Input/Output built-in microphone/-

Alarm Input/Output 1 (NO/NC)/1

Network Interface 1 x Ethernet - RJ-45 interface, 10/100 Mbit/s

Memory Card Slot microSD - capacity up to 128GB

Installaon parameters

Dimensions (mm) 120 (Ф) x 55 (H)

Weight 0.45 kg

Degree of Protecon IP 66 (details in the user’s manual on page 10)

Enclosure vandalproof aluminium, white

Power Supply PoE, 12 VDC

Power Consumpon 7 W, 11 W (IR on)

Operang Temperature -30°C ~ 55°C

NVIP-9F-4301 - User’s manual (short) ver 1.0

8

CAUTION!

If the device was brought from a location with lower temperature, please wait until it reaches the

temperature of location it is currently in. Turning the device on immediately after bringing it

from a location with lower ambient temperature is forbidden, as the condensing water vapour

may cause short-circuits and damage the device as a result.

Before starting the device familiarize yourself with the description and the role of particular

inputs, outputs and adjusting elements that the device is equipped with.

2. START-UP AND INITIAL CAMERA CONFIGURATION

2.1. Description of connectors

START-UP AND INITIAL CAMERA CONFIGURATION

Nr Connector Type/Color Funcon Descripon

1 RJ45 socket, white Port Ethernet 100Mbps Ethernet connector

2

BNC socket, white Video output CVBS video output

3

ARK screw terminal

block

1. Alarm input A

Alarm input, congurable: NC or NO

2. Alarm input B

3. Alarm output A

Alarm output, NO (relay, 12VDC/24VAC 0.3A max)

4. Alarm output B

4 - RESET buon Buon to restore factory sengs

5 DC2,5/5,5 socket Power connector Power supply, 12VDC ± 10%

1. 100 Mbps Ethernet port

2. CVBS video output

3. Alarm input/output block

4. Reset buon

5. 12VDC power supply connector

NVIP-9F-4301 - User’s manual (short) ver 1.0

9

START-UP AND INITIAL IP CAMERA CONFIGURATION

2.2. Power supply connection

When powering the camcorder from an external 12VDC power supply, make sure it has the correct

settings and that the power supply connector has the correct polarity. Using an incorrect power supply

may result in malfunction or damage.

The camera can also be powered via an RJ45 network connector, using PoE (IEEE 802.3af)

technology. Please, use a network switch or an IEEE 802.3af compliant PoE power supply to power

the camera through the PoE.

CAUTION!

It is forbidden to use – as the camera power source – PoE equipment (adapters, etc.) not compatible with

IEEE 802.3af standard (items called “passive PoE power supply”). Damages that results from the usage

of improper power supply source are not covered by the warranty.

2.3. Connecting ethernet cable

To maintain tightness of ethernet cable connection, please follow instruction below:

1. Unscrew the nut (b) from the connector cover (a), mount the sealing ring on the socket (c)

2. Route the network cable through the components (a) and (b). Plug the RJ-45 connector into the

socket (c)

3. Screw the connector cover (a) on the socket (c). Inside the upper part of the connector cover (a)

push in to the stop the seal of the cable (d) - the seal is cut to insert on the network cable.

4. Tighten up to the stop nut (b)

WARNING!

Other connectors and sockets, outside of the RJ-45 socket, are not hermetically sealed. User

should seal this connector by himself.

b a

b

a

c

d

Center pin +12V

GND

NVIP-9F-4301 - User’s manual (short) ver 1.0

10

START-UP AND INITIAL IP CAMERA CONFIGURATION

2.4. Camera mounting

To mount a camera please follow the instructions below:

 Put mounting drawing paper to the wall or ceiling and mark drill holes.

 Drill holes for screws and for video and power cables.

 Connect the base with the camera position adjustment element as shown in the picture

 Using mounting screws from the package, attach the base of camera to the ceiling/wall

 Put video and power cables through a base of camera and a previously drilled hole in the wall/

ceiling.

 Push the camera to the base and then turn to the left to snap the camera into the base

WARNING!

Please note that the wall or ceiling must have enough strength to support the IP Camera.

WARNING!

In order to obtain declared degree of protection please seal the camera bracket to prevent water

getting inside. Furthermore, when installing the bracket on rough/uneven surfaces, please

additionally seal the junction with appropriate sealing mass. Please pay special attention to any

mounting holes and if they are a loop-through ones, seal them too.

WARNING!

The declared degree of protection of the camera relates to its housing and does not take into

account the possibility of moisture infiltration into the interior of the camera by connecting

cables. Connection cables protection through i.e. sealing up is the responsibility of the camera

installer. The manufacturer is not liable for any damages to the camera caused as a result of

failing in performing that activity by installer, which also means that camera damaged in that

way is not subject to warranty repairs.

NVIP-9F-4301 - User’s manual (short) ver 1.0

11

START-UP AND INITIAL CAMERA CONFIGURATION

2.5. Starting the IP camera

To run NOVUS IP camera you have to connect ethernet cable between camera and network switch.

To power it up you can connect it directly via power supply adapter with parameters compatible with

camera power supply specification, or camera can be powered with PoE (IEEE 802.3af ) compatible

switch.

After connecting power supply it takes about 30 seconds to start camera. Then You can proceed to

connect to the camera via web browser.

The recommended way to start an IP camera and perform its configuration is a connection directly

to the network switch which is not connected to other devices. To obtain further information about

network configuration parameters (IP address, gateway, network mask, etc.) please contact your

network administrator.

 Connection utilising network switch with PoE support

 Connection utilising external power supply and network switch

Network transmission

Network switch

Computer

IP camera

Computer

IP camera

Power supply and network

transmission

Network transmission

Network PoE switch

NVIP-9F-4301 - User’s manual (short) ver 1.0

12

START-UP AND INITIAL CAMERA CONFIGURATION

 Connection utilising external power supply directly to the computer

2.6. Initial configuration via the web browser

The default network settings for NVIP-9DN2018V/IR-1P camera are:

1. IP address= 192.168.1.200

2. Network mask - 255.255.255.0

3. Gateway - 192.168.1.1

4. User name - root

5. Password - pass

Knowing the camera’s IP address you need to appropriately set PC IP address, so the two devices can

operate in one network subnet ( e.g. for IP 192.168.1.1, appropriate address for the camera ranges from

192.168.1.2 to 192.168.1.254, for example 192.168.1.60). It is not allowed to set the same addresses for

camera and PC computer

You can either set a network configuration (IP address, gateway, net mask, etc.) of NOVUS IP camera

yourself or select DHCP mode (DHCP server is required in this method in target network) by using

web browser or by NMS software. When you use DHCP server check IP address lease and its linking

with camera MAC address to avoid changing or losing IP address during device operation or network/

DHCP server breakdown. You have to remember to use a new camera IP address after changing

network parameters.

After network setting configuration has been done, the camera can be connected to a target network.

Network transmission - cross over cable

Computer

IP Camera

NVIP-9F-4301 - User’s manual (short) ver 1.0

13

START-UP AND INITIAL CAMERA CONFIGURATION

2.7. Security recommendations for network architecture and configuration

WARNING!

Below are shown security recommendations for network architecture and configuration

of CCTV systems that are connected to the Internet to reduce the risk

of unauthorized interference with the system by a third party.

1. Absolutely change the default passwords and user names (if the device gives this possibility) of

all applied network devices (recorders, cameras, routers, network switches, etc.) to the

severely complexity password. Use lowercase and uppercase letters, numbers, and special characters

if there is such possibility.

2. Depending on the available functionality in the order to restrict access to the used network devices at

the administrator account level, it is recommended to configure the users accounts accordingly.

3. Do not use DMZ function (Demilitarized zone) in your router. Using that function you open the

access to recorder system from the Internet on all ports, which gives possibility for an unauthorized

interference with the system.

Instead of DMZ use port forwarding redirect only the ports which are necessary for the performance

of the connection (detailed information about ports of communication in different models of recorders,

cameras, etc. can be found in the operating instructions).

4. Use routers with firewall function and make sure it is enabled and properly configured.

5. It is recommended to change the default network communication port numbers of used devices

if there is such possibility.

6. If used network devices has a UPnP feature and it is not used, turn it off.

7. If used network devices has a P2P feature and it is not used, turn it off.

8. If used network devices support HTTPS protocol for connection, it is recommended to use it.

9. If used network devices support IP filtering for authorized connections function, it is recommended

to use it.

10. If used recorder has two network interfaces it is recommended to use both of them to physically

separate network for cameras and network for Internet connection. The only device in the system,

accessible from Internet will be recorder - there will be no physically access directly to any camera.

NVIP-9F-4301 - User’s manual (short) ver 1.0

14

NETWORK CONNECTION UTILIZING WEB BROWSER

3. NETWORK CONNECTION USING WEB BROSWER

3.1. Recommended PC specification for web browser connections

Requirements below apply to connection with an IP camera, assuming smooth image display in

3000x3000 resolution and 30 fps speed.

1. CPU Intel Core i3 3GHz or newer

2. RAM Memory min. 4 GB

3. Graphic card NVIDIA GeForce 1 GHz or higher

4. OS Windows VISTA / 7 / 8 / 10

5. Network card 10/100/1000 Mb/s

3.2. Connection with IP camera via web browser

You have to enter camera IP address in the address bar. When you connect to the camera, web browser

will download the applet for displaying images from the camera. In Internet Explorer before the first

logon you need to install "SurveillancePlugin.exe” addition. To do this, please click on the link

"Download" and when you get the download window, click "Run" button.

When the addition installer window appears, temporarily close the browser and click "Install" button.

After installation, launch a web browser and connect to the camera.

NVIP-9F-4301 - User’s manual (short) ver 1.0

15

If the installation fails, changing security settings for the IE browser is required. In order to do that,

please choose: Tools > Internet options > Security tab > Custom level and:

 Under Download unsigned A ctiveX controls - select either Enable or Prompt

 Under Initialize and script ActiveX controls not marked as safe - select Enable or Prompt

You can also add the camera’s IP address to “trusted zone” and set lowest security level for it.

In addition, when working in Windows Vista/7/8 the ActiveX applet may be blocked by Windows

Defender or User account control. In such case you should allow to run this applet, or simply disable

these functions.

When the addition is installed it will be possible to log into the camera. On the login page, enter your

login information. Here can also change the language of the camera interface can be maid.

For safety reasons, we recommend to change the default password and user name.

NETWORK CONNECTION UTILIZING WEB BROWSER

NVIP-9F-4301 - User’s manual (short) ver 1.0

16

USING AND CONFIGURING

4. USING AND CONFIGURING

4.1. The Remote Preview Interface

1. Icon that enables the image display options panel:

USING AND CONFIGURING

8. 6. 7.

"Mount type" - icons for determining the way of

mounting the camera. The right choice affects the

selection of image geometry correction and

allows to display it with as little distortion as

possible

"Display mode" - icons for choosing how to

display the image. The type and number of

available display options depends on the chosen

installation location.

4.

5.

3.

1. 2.

NVIP-9F-4301 - User’s manual (short) ver 1.0

17

2. The selection buttons to select the stream to be displayed in the Remote Preview window.

3. Buttons for selecting the operating mode and configure the camera:

Live - enables preview live stream

Playback - displays the playback panel

Remote Setting - displays the configuration panel camera

Local Setting - displays the configuration panel of paths to snapshots folders

4. Icon to access to the camera:

5. Icon to enable/disable panel to set the image parameters:

6. Icons for selecting the operating mode

7. Icons icons that control additional functions

USING AND CONFIGURING

The panel is able to adjust the hue,

brightness, contrast, color saturation and

sharpness (clarity).

- enables the display of the video stream

- disables the display of the video stream

- sets full screen

- enables and disables the record a video stream on your computer

- performs a screenshot and saves on your computer

- enables and disables the volume control options

- enables and disables audio transmission

- displays information about the logged in user and the version of the applet

- logout from the camera

NVIP-9F-4301 - User’s manual (short) ver 1.0

18

ELECTRIC CONNECTORS AND RESTORING FACTORY DEFAULTS

8. Live Preview window.

Double-clicking on the live view window enables the display of the image on the full screen.

Additionally, depending on the display mode selected previously (see point 1), it is possible to modify

the display method: rotation, selection of the field of view, zooming (virtual PTZ). These operations are

carried out using the mouse, by pressing and holding the left key and dragging the mouse.

5. ELECTRIC CONNECTORS

5.1. Connecting of the alarm input.

5.1. Connecting of the alarm output.

6. RESTORING FACTORY DEFAULTS

6.1. Software restore to factory defaults

Camera NVIP-9DN2018V/IR-1P allows you to reset your settings to the factory values. To restore the

camera settings to the default, go to the "Load Default" tab (Remote Setting -> Advanced -> Load

Default). Then select options and functions of the camera whose settings are to be reset and press the

"Save" button.

After about 30 seconds, you can reconnect to the camera (at the current IP address, as long as it was not

reset network settings or on the default IP address).

Note: To make a software restore factory settings, you must be logged in as "root".

6.2 Hardware restore to factory defaults

You can use the RESET button located on the camera cable to reset the camera's settings. To reset the

defaults using the RESET button, press and hold for about 5 seconds.

After about 30 seconds, you will be able to reconnect to the camera at the default IP address.

Trigger contact

signaling device

Max. load 0.3A

signaling device power supply

12VDC or 24VAC max.

NVIP-9F-4301 - User’s manual (short) ver 1.0

19

ELECTRIC CONNECTORS AND RESTORING FACTORY DEFAULTS

7. INSTALLING SD CARD

The microSD card slot is located in the bottom part of the camera housing under the cover:

To install a memory card:

1. Disconnect the power supply of the camera, unscrew two screws securing the cover

2. Remove the cover taking care not to lose or damage the gasket under it

3. Open the card lock by moving it in the direction of the arrow and lifting it

4. Install the memory card as shown below:

5. Close the card lock, press lightly and move in the opposite direction to that shown in point. 3.

Install the cover paying attention to the correct positioning of the gasket.

6. Connect the power of the camera. After starting the camera, the memory card will be

recognized and its status can be checked in the tab "Device -> SD card"

16.06.2020 JZ MK v1.0

AAT SYSTEMY BEZPIECZEŃSTWA Sp. z o.o.

431 Pulawska St., 02-801 Warsaw, Poland

tel.: +4822 546 07 00, fax: +4822 546 07 59

www.novuscctv.com

Strona się ładuje...

Novus NVIP-9F-4301 Instrukcja obsługi

Niniejsza instrukcja jest również odpowiednia dla

Novus NVIP-9F-4301 Instrukcja obsługi

w innych językach

Powiązane artykuły