Indesit K6G56S.A (X)/U instrukcja

Kategoria
Mikrofale
Typ
instrukcja

Ten podręcznik jest również odpowiedni dla

GB
COOKER AND OVEN
K6G56S.A /U
K6G52.A /U
K6G52.S A /U
KN6G62SA /U
KN6G66SA /U
Contents
Installation, 2-5
Positioning and levelling
Electrical connection
Gas connection
Adapting to different types of gas
Table of burner and nozzle specifications
Table of characteristics
Description of the appliance, 6
Overall view
Control panel
Start-up and use, 7-11
Using the hob
Using the oven
Using the cooking timer
Cooking modes
Practical cooking advice
Planning cooking with the electronic programmer
Oven cooking advice table
Precautions and tips, 12
General safety
Disposal
Respecting and conserving the environment
Care and maintenance, 13
Switching the appliance off
Cleaning the appliance
Replacing the oven light bulb
Gas tap maintenance
Assistance
Operating Instructions
English, 1
GB
Polski, 14
PL
KN6G660SA /U
2
GB
! Before operating your new appliance please read this
instruction booklet carefully. It contains important
information concerning the safe installation and
operation of the appliance.
! Please keep these operating instructions for future
reference. Make sure that the instructions are kept with
the appliance if it is sold, given away or moved.
! The appliance must be installed by a qualified
professional according to the instructions provided.
! Any necessary adjustment or maintenance must be
performed after the cooker has been disconnected
from the electricity supply.
Room ventilation
The appliance may only be installed in permanently-
ventilated rooms, according to current national
legislation. The room in which the appliance is
installed must be ventilated adequately so as to
provide as much air as is needed by the normal gas
combustion process (the flow of air must not be lower
than 2 m
3
/h per kW of installed power).
The air inlets, protected by grilles, should have a duct
with an inner cross section of at least 100 cm
2
and
should be positioned so that they are not liable to
even partial obstruction (
see figure A
).
These inlets should be enlarged by 100% - with a
minimum of 200 cm
2
- whenever the surface of the hob
is not equipped with a flame failure safety device.
When the flow of air is provided in an indirect manner
from adjacent rooms (
see figure B
), provided that
these are not communal parts of a building, areas with
increased fire hazards or bedrooms, the inlets should
be fitted with a ventilation duct leading outside as
described above.
! After prolonged use of the appliance, it is advisable to
open a window or increase the speed of any fans used.
Disposing of combustion fumes
The disposal of combustion fumes should be
guaranteed using a hood connected to a safe and
efficient natural suction chimney, or using an electric
fan that begins to operate automatically every time the
appliance is switched on (
see figure
).
! The liquefied petroleum gases are heavier than air
and collect by the floor, therefore all rooms containing
LPG cylinders must have openings leading outside so
that any leaked gas can escape easily.
LPG cylinders, therefore, whether partially or
completely full, must not be installed or stored in
rooms or storage areas that are below ground level
(cellars, etc.). Only the cylinder being used should be
stored in the room; this should also be kept well away
from sources of heat (ovens, chimneys, stoves) that
may cause the temperature of the cylinder to rise
above 50°C.
Positioning and levelling
! It is possible to install the appliance alongside
cupboards whose height does not exceed that of the
hob surface.
! Make sure that the wall in contact with the back of
the appliance is made from a non-flammable, heat-
resistant material (T 90°C).
To install the appliance correctly:
Place it in the kitchen, dining room or the bed-sit
(not in the bathroom).
If the top of the hob is higher than the cupboards,
the appliance must be installed at least 200 mm
away from them.
If the cooker is installed underneath a wall cabinet,
there must be a minimum distance of 420 mm
between this cabinet and the top of the hob.
Installation
Adjacent room Room requiring
ventilation
A
B
Ventilation opening for
comburent air
Increase in the gap
between the door and
the flooring
A
Fumes channelled
straight outside
Fumes channelled through a
chimney or a branched flue
system (reserved for cooking
appliances)
GB
3
If the cooker is
installed underneath a
wall cabinet, there must
be a minimum distance
of 420 mm between this
cabinet and the top of
the hob.
This distance should be
increased to 700 mm if
the wall cabinets are
flammable (
see figure
).
Do not position blinds behind the cooker or less
than 200 mm away from its sides.
Any hoods must be installed according to the
instructions listed in the relevant operating manual.
Levelling
If it is necessary to level the
appliance, screw the adjustable
feet into the places provided on
each corner of the base of the
cooker (
see figure
).
The legs* fit into the slots on
the underside of the base of
the cooker.
Electrical connection
Install a standardised plug corresponding to the load
indicated on the appliance data plate (
see Technical
data table
).
The appliance must be directly connected to the
mains using an omnipolar circuit-breaker with a
minimum contact opening of 3 mm installed between
the appliance and the mains. The circuit-breaker must
be suitable for the charge indicated and must comply
with NFC 15-100 regulations (the earthing wire must
not be interrupted by the circuit-breaker). The supply
cable must be positioned so that it does not come into
contact with temperatures higher than 50°C at any
point.
Before connecting the appliance to the power supply,
make sure that:
The appliance is earthed and the plug is compliant with
the law.
The socket can withstand the maximum power of the
appliance, which is indicated by the data plate.
HOOD
420
Min.
min. 650 mm. with hood
min.
700 mm. without hood
mm.
600
Min. mm.
420
Min. mm.
The voltage is in the range between the values
indicated on the data plate.
The socket is compatible with the plug of the
appliance. If the socket is incompatible with the
plug, ask an authorised technician to replace it. Do
not use extension cords or multiple sockets.
! Once the appliance has been installed, the power
supply cable and the electrical socket must be easily
accessible.
! The cable must not be bent or compressed.
! The cable must be checked regularly and replaced
by authorised technicians only.
! The manufacturer declines any liability should
these safety measures not be observed.
Gas connection
Connection to the gas network or to the gas cylinder
may be carried out using a flexible rubber or steel hose,
in accordance with current national legislation and after
making sure that the appliance is suited to the type of
gas with which it will be supplied (see the rating sticker
on the cover: if this is not the case
see below
). When
using liquid gas from a cylinder, install a pressure
regulator which complies with current national
regulations. To make connection easier, the gas supply
may be turned sideways*: reverse the position of the
hose holder with that of the cap and replace the gasket
that is supplied with the appliance.
! Check that the pressure of the gas supply is
consistent with the values indicated in the Table of
burner and nozzle specifications (
see below
). This will
ensure the safe operation and durability of your
appliance while maintaining efficient energy
consumption.
Gas connection using a flexible rubber hose
Make sure that the hose complies with current
national legislation. The internal diameter of the hose
must measure: 8 mm for liquid gas supply; 13 mm for
methane gas supply.
Once the connection has been performed, make sure
that the hose:
Does not come into contact with any parts that
reach temperatures of over 50°C.
Is not subject to any pulling or twisting forces and
that it is not kinked or bent.
Does not come into contact with blades, sharp
corners or moving parts and that it is not
compressed.
4
GB
Is easy to inspect along its whole length so that its
condition may be checked.
Is shorter than 1500 mm.
Fits firmly into place at both ends, where it will be
fixed using clamps that comply with current
regulations.
! If one or more of these conditions is not fulfilled or if
the cooker must be installed according to the
conditions listed for class 2 - subclass 1 appliances
(installed between two cupboards), the flexible steel
hose must be used instead (
see below
).
Connecting a flexible jointless stainless steel pipe
to a threaded attachment
Make sure that the hose and gaskets comply with
current national legislation.
To begin using the hose, remove the hose holder on
the appliance (the gas supply inlet on the appliance is
a cylindrical threaded 1/2 gas male attachment).
! Perform the connection in such a way that the hose
length does not exceed a maximum of 2 metres,
making sure that the hose is not compressed and
does not come into contact with moving parts.
Checking the tightness of the connection
When the installation process is complete, check the
hose fittings for leaks using a soapy solution. Never
use a flame.
Adapting to different types of gas
It is possible to adapt the appliance to a type of gas
other than the default type (this is indicated on the
rating label on the cover).
Adapting the hob
Replacing the nozzles for the hob burners:
1. Remove the hob grids and slide the burners off their
seats.
2. Unscrew the nozzles using a
7 mm socket spanner (
see
figure
), and replace them with
nozzles suited to the new type
of gas (
see Burner and nozzle
specifications table
).
3. Replace all the components
by following the above
instructions in reverse.
Adjusting the hob burners’ minimum setting:
1. Turn the tap to the minimum position.
2. Remove the knob and adjust the regulatory screw,
which is positioned inside or next to the tap pin, until
the flame is small but steady.
! If the appliance is connected to a liquid gas supply,
the regulatory screw must be fastened as tightly as
possible.
3. While the burner is alight, quickly change the position of
the knob from minimum to maximum and vice versa
several times, checking that the flame is not extinguished.
! The hob burners do not require primary air adjustment.
! After adjusting the appliance so it may be used with a
different type of gas, replace the old rating label with a new
one that corresponds to the new type of gas (these labels
are available from Authorised Technical Assistance
Centres).
! Should the gas pressure used be different (or vary
slightly) from the recommended pressure, a suitable
pressure regulator must be fitted to the inlet hose in
accordance with current national regulations relating to
“regulators for channelled gas”.
GB
5
Table of burner and nozzle specifications
Table 1 G30 (GPB-B) G20 (GZ50) G2.350 (GZ35)
 































    
            


           


           




  













S
S
R
A
K6G56S.A /U
K6G52.A /U
K6G52.S A /U
KN6G62SA /U
KN6G66SA /U
TABLE OF CHARACTERISTSICS
Dimensions
width 43,5 cm
height 32 cm
depth 40 cm
Volume
56 l
Useful
measurements
relating to the oven
compartment
width 46 cm
height 8,5 cm
depth 44 cm
Burners
may be adapted for use with any type
of gas shown on the data plate.
Voltage and
frequency
see data plate
ENERGY LABEL
Directive 2002/40/EC on the label of
electric ovens.
Standard EN 50304
Energy consumption for Natural
convection – heating mode:
Convection;
Declared energy consumption for
Forced convection Class – heating
mode: Baking
This appliance conforms to the
following European Economic
Community directives: 2006/95/EC
dated 12/12/06 (Low Voltage) and
subsequent amendments -
2004/108/EC dated 15/12/04
(Electromagnetic Compatibility) and
subsequent amendments -
2004/142/EC dated 30/11/09 (Gas)
and subsequent amendments -
93/68/EEC dated 22/07/93 and
subsequent amendments.
2002/96/EC
1275/2008 (Stand-by/ Off mode)
KN6G660SA /U
6
GB
Description
of the appliance
Overall view
Control panel
*
Only available in certain models.
BURNER
control knobs
SELECTOR
knob
THERMOSTAT
knob
THERMOSTAT
indicator light
COOKING TIMER knob*
Electronic
programmer*
Hob grid
Glass cover*
Control panel
GRILL rack
DRIPPING PAN
GUIDE RAILS
for the sliding racks
position 3
position 2
position 1
Gas burner
Containment
surface for spills
Adjustable foot
Adjustable foot
position 5
position 4
BURNER
control knobs
SELECTOR
knob
THERMOSTAT
knob
THERMOSTAT
indicator light
COOKING TIMER knob*
Electronic
programmer*
GB
7
Start-up and use
Using the hob
Lighting the burners
For each BURNER knob there is a full ring showing
the strength of the flame for the relevant burner.
To light one of the burners on the hob:
1. Bring a flame or gas lighter close to the burner.
2. Press the BURNER knob and turn it in an
anticlockwise direction so that it is pointing to the
maximum flame setting E.
3. Adjust the intensity of the flame to the desired
level by turning the BURNER knob in an
anticlockwise direction. This may be the minimum
setting C, the maximum setting E or any position in
between the two.
If the appliance is fitted with an electronic lighting
device* (
see figure
), press the BURNER knob and
turn it in an anticlockwise direction, towards the
minimum flame setting, until the burner is lit. The
burner may be extinguished when the knob is
released. If this occurs, repeat the operation, holding
the knob down for a longer period of time.
! If the flame is accidentally extinguished, switch off
the burner and wait for at least 1 minute before
attempting to relight it.
The appliance is equipped with a flame failure safety
device; press and hold the BURNER knob for
approximately 3-7 seconds to keep the flame alight
and to activate the device.
To switch the burner off, turn the knob until it
reaches the stop position •.
Practical advice on using the burners
For the burners to work in the most efficient way
possible and to save on the amount of gas
consumed, it is recommended that only pans that
have a lid and a flat base are used. They should
also be suited to the size of the burner:
Burner ø Cookware diameter (cm)
Fast(R) 24-26
SemiFast(S) 16-20
Auxiliary(A) 10-14
To identify the type of burner, please refer to the
diagrams contained in the “Burner and nozzle
specifications”.
Using the oven
! The first time you use your appliance, heat the
empty oven with its door closed at its maximum
temperature for at least half an hour. Ensure that the
room is well ventilated before switching the oven off
and opening the oven door. The appliance may emit
a slightly unpleasant odour caused by protective
substances used during the manufacturing process
burning away.
! Before operating the product, remove all plastic
film from the sides of the appliance.
! Never put objects directly on the bottom of the
oven; this will avoid the enamel coating being
damaged.
! Should the appliance be equipped with an
electronic programmer*, to use the electric oven, just
press buttons
and at the same time (the
symbol will appear on the display) before
selecting the desired cooking function.
1. Select the desired cooking mode by turning the
SELECTOR knob.
2. Select the recommended temperature for the
cooking mode or the desired temperature by turning
the THERMOSTAT knob.
A list detailing cooking modes and suggested
cooking temperatures can be found in the relevant
table (
see Oven cooking advice table
).
During cooking it is always possible to:
Change the cooking mode by turning the
SELECTOR knob.
Change the temperature by turning the
THERMOSTAT knob.
Stop cooking by turning the SELECTOR knob to
the “0” position.
! Always place cookware on the rack(s) provided.
*
Only available in certain models.
HOB GAS BURNER
SAFETY DEVICE
ELECTRONIC
LIGHTING DEVICE
WARNING! The glass lid can break in
if it is heated up. Turn off all the burn-
ers and the electric plates before clos-
ing the lid. *Applies to the models with
glass cover only.
8
GB
MULTI-COOKING mode
All the heating elements (top, bottom and circular),
as well as the fan, will come on. Since the heat
remains constant throughout the oven, the air cooks
and browns food uniformly. A maximum of two racks
may be used at the same time.
BARBECUE mode
The top heating element comes on.
The high and direct temperature of the grill is
recommended for food that requires high surface
temperature. Always cook in this mode with the oven
door closed.
GRATIN mode
The top heating element, as well as the fan, will
come on. This combination of features increases the
effectiveness of the unidirectional thermal radiation
of the heating elements through forced circulation of
the air throughout the oven. This helps prevent food
from burning on the surface, allowing the heat to
penetrate right into the food. Always cook in this
mode with the oven door closed.
PIZZA mode
The bottom and circular heating elements, as well as
the fan, will come on. This combination heats the
oven rapidly by producing a considerable amount of
heat, particularly from the bottom element. If you
use more than one rack simultaneously, switch the
position of the dishes halfway through the cooking
process.
BAKING mode
The rear heating element and the fan come on,
guaranteeing the distribution of heat delicately and
uniformly throughout the oven. This mode is ideal for
baking and cooking temperature sensitive foods
such as cakes that need to rise and to prepare
certain tartlets on 3 shelves simultaneously.
Practical cooking advice
! Do not place racks in position 1 and 5 during fan-
assisted cooking. Excessive direct heat can burn
temperature sensitive foods.
! In the BARBECUE and GRATIN cooking modes,
THERMOSTAT indicator light
When this is illuminated, the oven is generating
heat. It switches off when the inside of the oven
reaches the selected temperature. At this point the
light illuminates and switches off alternately,
indicating that the thermostat is working and is
maintaining the temperature at a constant level.
Oven light
This is switched on by turning the SELECTOR knob
to any position other than “0”. It remains lit as long
as the oven is operating. By selecting
88
88
8 with the
knob, the light is switched on without any of the
heating elements being activated.
Using the cooking timer*
1. To set the buzzer, turn the COOKING TIMER knob
clockwise almost one complete revolution.
2. Turn the knob anticlockwise to set the desired
time: align the minutes shown on the COOKING
TIMER knob with the indicator on the control panel.
3. When the selected time has elapsed, a buzzer
sounds and the oven turns off.
4. When the oven is off the cooking timer can be
used as a normal timer.
! To use the oven manually, in other words when you
do not wish to use the end of cooking timer, turn the
COOKING TIMER knob until it reaches the 9
symbol.
Cooking modes
! A temperature value can be set for all cooking
modes between 60°C and Max, except for
BARBECUE (recommended: set only to MAX
power level);
GRATIN (recommended: do not exceed 200°C).
TRADITIONAL OVEN mode
Both the top and bottom heating elements will come
on. With this traditional cooking mode, it is best to
use one cooking rack only: if more than one rack is
used, the heat will be distributed unevenly.
GB
9
*
Only available in certain models.
1. press the TIMER button
. The display shows:
N.
2. Press the + and - buttons to set the desired time.
3. When the buttons are released the timer begins
counting down and the current time appears on the
display.
R
4. After the time has elapsed a buzzer will sound,
and this can be switched off by pressing any button
(except the + and - buttons). The symbol
will
switch off.
!!
!!
!
The timer does not switch the oven on or off.
Adjusting the volume of the buzzer
After selecting and confirming the clock settings,
use the - button to adjust the volume of the alarm
buzzer.
Setting the cooking time with a delayed start
First decide which cooking mode you wish to use
and set a suitable temperature using the SELECTOR
and THERMOSTAT knobs on the oven.
At this point it is possible to set the cooking time:
1. Press the COOKING TIME button
.
2. Within 4 seconds of having pressed this button,
set the desired amount of time by pressing the + and
- buttons. If, for example, you wish to set a cooking
time of 30 minutes, the display will show:
N
3. 4 seconds after the buttons are released, the
current time (for example 10.00) reappears on the
display with the symbol
mm
mm
m
and the letter A (AUTO).
Next the desired cooking end time must be set:
4. Press the END COOKING TIME button
.
5. Within 4 seconds of having pressed this button,
adjust the cooking end time by pressing the + and -
buttons. If, for example, you want cooking to end at
13.00, the display shows:
O
6. 4 seconds after the buttons are released, the
current time (for example 10.00) reappears on the
display with the letter A (AUTO).
P
At this point, the oven is programmed to switch on
automatically at 12:30 and switch off after 30
minutes, at 13.00.
Setting the cooking time with an immediate start
place the dripping pan in position 1 to collect
cooking residues (fat and/or grease).
MULTI-COOKING
Use position 2 and 4, placing the food that
requires more heat on 2.
Place the dripping pan on the bottom and the rack
on top.
BARBECUE
Insert the rack in position 3 or 4. Place the food in
the centre of the rack.
We recommend that you set the maximum power
level. The top heating element is regulated by a
thermostat and may not always be on.
PIZZA MODE
Use a light aluminium pizza pan. Place it on the
rack provided.
For a crispy crust, do not use the dripping pan
(prevents crust from forming by extending cooking
time).
If the pizza has a lot of toppings, we recommend
adding the mozzarella cheese on top of the pizza
halfway through the cooking process.
Planning cooking with the electronic
programmer*
Setting the clock
After the appliance has been connected to the power
supply, or after a blackout, the display will
automatically reset to 0:00 and begin to blink. To set
the time:
1. Press the COOKING TIME button
and the
COOKING END TIME
simultaneously.
2. Within 4 seconds of having pressed these
buttons, set the exact time by pressing the + and -
buttons. The + button advances the hours and the
-
button decreases the hours.
Once the time has been set, the programmer
automatically switches to manual mode.
Setting the timer
The timer enables a countdown to be set, when the
time has elapsed a buzzer sounds.
To set the timer proceed as follows:
10
GB
*
Only available in certain models.
Follow the above procedure for setting the cooking
time (points 1-3).
! When the letter A appears, this indicates that both
the cooking time and the end cooking time have
been programmed in AUTO mode. To restore the
oven to manual operation, after each AUTO cooking
mode press the COOKING TIME
and END
COOKING TIME
buttons simultaneously.
! The symbol
mm
mm
m
will remain lit, along with the oven,
for the entire duration of the cooking programme.
The set cooking duration can be displayed at any
time by pressing the COOKING TIME button
,
and the cooking end time may be displayed by
pressing the END COOKING TIME button
.
When the cooking time has elapsed a buzzer
sounds. To stop it, press any button apart from the
+ and - buttons.
Cancelling a previously set cooking programme
Press the COOKING TIME button
and the
COOKING END TIME
simultaneously.
Correcting or cancelling previously set data
The data entered can be changed at any time by
pressing the corresponding button (TIMER,
COOKING TIME or COOKING END TIME) and the +
or - button.
When the cooking time data is cancelled, the
cooking end time data is also cancelled
automatically, and vice versa.
If the oven has already been programmed, it will not
accept cooking end times which are before the start
of the programmed cooking process.
GB
11
Oven cooking advice table
Cooking
modes
Foods Weight
(in kg)
Rack position Pre-heating
time (min)
Recommended
temperature
Cooking
time
(minutes)
Convection
Oven
Duck
Roast veal or beef
Pork roast
Biscuits (short pastry)
Tarts
1
1
1
-
1
3
3
3
3
3
15
15
15
15
15
200
200
200
180
180
65-75
70-75
70-80
15-20
30-35
Multi-cooking
Pizza (on 2 racks)
Lasagne
Lamb
Roast chicken + potatoes
Mackerel
Plum cake
Cream puffs (on 2 racks)
Biscuits (on 2 racks)
Sponge cake (on 1 rack)
Sponge cake (on 2 racks)
Savoury pies
1
1
1
1+1
1
1
0.5
0.5
0.5
1
1.5
2 and 4
3
2
2 and 4
2
2
2 and 4
2 and 4
2
2 and 4
3
15
10
10
15
10
10
10
10
10
10
15
230
180
180
200
180
170
190
180
170
170
200
15-20
30-35
40-45
60-70
30-35
40-50
20-25
10-15
15-20
20-25
25-30
Barbecue
Soles and cuttlefish
Squid and prawn kebabs
Cod filet
Grilled vegetables
Veal steak
Cutlets
Hamburgers
Mackerels
Toasted sandwiches
1
1
1
1
1
1
1
1
n.° 4
4
4
4
3 or 4
4
4
4
4
4
5
5
5
5
5
5
5
5
5
MAX
MAX
MAX
MAX
MAX
MAX
MAX
MAX
MAX
8-10
6-8
10
10-15
15-20
15-20
7-10
15-20
2-3
Gratin
Grilled chicken
Cuttlefish
1.5
1.5
2
2
5
5
200
200
55-60
30-35
Pizza Mode
Pizza
Roast veal or beef
Chicken
0.5
1
1
3
2
2 or 3
15
10
10
220
220
180
15-20
25-30
60-70
Baking Mode
Tarts
Fruit cakes
Plum cake
Sponge cake
Stuffed pancakes (on 2 racks)
Small cakes (on 2 racks)
Cheese puffs (on 2 racks)
Cream puffs (on 3 racks)
Biscuits (on 3 racks)
Meringues (on 3 racks)
0.5
1
0.7
0.5
1.2
0.6
0.4
0.7
0.7
0.5
3
2 or 3
3
3
2 and 4
2 and 4
2 and 4
1 and 3 and 5
1 and 3 and 5
1 and 3 and 5
15
15
15
15
15
15
15
15
15
15
180
180
180
160
200
190
210
180
180
90
20-30
40-45
40-50
25-30
30-35
20-25
15-20
20-25
20-25
180
12
GB
Precautions and tips
! This appliance has been designed and manufactured
in compliance with international safety standards.
The following warnings are provided for safety
reasons and must be read carefully.
General safety
The appliance was designed for domestic use
inside the home and is not intended for
commercial or industrial use.
The appliance must not be installed outdoors, even
in covered areas. It is extremely dangerous to
leave the appliance exposed to rain and storms.
Do not touch the appliance with bare feet or with
wet or damp hands and feet.
The appliance must be used by adults only for the
preparation of food, in accordance with the
instructions provided in this booklet.
The instruction booklet accompanies a class 1
(insulated) or class 2 - subclass 1 (recessed
between 2 cupboards) appliance.
Keep children away from the oven.
Make sure that the power supply cables of other
electrical appliances do not come into contact
with the hot parts of the oven.
The openings used for the ventilation and
dispersion of heat must never be covered.
Always use oven gloves when placing cookware
in the oven or when removing it.
Do not use flammable liquids (alcohol, petrol,
etc...) near the appliance while it is in use.
Do not place flammable material in the lower
storage compartment or in the oven itself. If the
appliance is switched on accidentally, it could
catch fire.
Always make sure the knobs are in the “
position when the appliance is not in use.
When unplugging the appliance, always pull the plug
from the mains socket; do not pull on the cable.
Never perform any cleaning or maintenance work
without having disconnected the appliance from
the electricity mains.
If the appliance breaks down, under no
circumstances should you attempt to repair the
appliance yourself. Repairs carried out by
inexperienced persons may cause injury or further
malfunctioning of the appliance. Contact
Assistance.
Do not rest heavy objects on the open oven door.
The appliance should not be operated by people
(including children) with reduced physical,
sensory or mental capacities, by inexperienced
individuals or by anyone who is not familiar with
the product. These individuals should, at the very
least, be supervised by someone who assumes
responsibility for their safety or receive
preliminary instructions relating to the operation of
the appliance.
Do not let children play with the appliance.
Do not place flammable materials in the lower
oven compartment.
The internal surfaces of the compartment (where
present) may become hot.
Do not close the cover when the burners are alight
or when they are still hot.
Remove any liquid from the lid before opening it.
Disposal
When disposing of packaging material: observe
local legislation so that the packaging may be
reused.
The European Directive 2002/96/EC relating to
Waste Electrical and Electronic Equipment
(WEEE) states that household appliances should
not be disposed of using the normal solid urban
waste cycle. Exhausted appliances should be
collected separately in order to optimise the cost
of re-using and recycling the materials inside the
machine, while preventing potential damage to
the atmosphere and to public health. The
crossed-out dustbin is marked on all products to
remind the owner of their obligations regarding
separated waste collection. For more information
relating to the correct disposal of household
appliances, owners should contact their local
authorities or appliance dealer.
Respecting and conserving the
environment
You can help to reduce the peak load of the
electricity supply network companies by using the
oven in the hours between late afternoon and the
early hours of the morning.
Always keep the oven door closed when using the
BARBECUE and GRATIN modes: to attain best
results and to save energy (approximately 10%).
Check the door seals regularly and wipe them
clean to ensure they are free of debris so that
they adhere properly to the door, thus avoiding
heat dispersion.
The appliance must be used by adults only for theThe appliance must be used by adults only for the
The appliance must be used by adults only for theThe appliance must be used by adults only for the
The appliance must be used by adults only for the
preparation of food, in accordance with thepreparation of food, in accordance with the
preparation of food, in accordance with thepreparation of food, in accordance with the
preparation of food, in accordance with the
instructions outlined in this booklet. Any other useinstructions outlined in this booklet. Any other use
instructions outlined in this booklet. Any other useinstructions outlined in this booklet. Any other use
instructions outlined in this booklet. Any other use
of the appliance (e.g. for heating the room)of the appliance (e.g. for heating the room)
of the appliance (e.g. for heating the room)of the appliance (e.g. for heating the room)
of the appliance (e.g. for heating the room)
constitutes improper use and is dangerous. Theconstitutes improper use and is dangerous. The
constitutes improper use and is dangerous. Theconstitutes improper use and is dangerous. The
constitutes improper use and is dangerous. The
manufacturer may not be held liable for anymanufacturer may not be held liable for any
manufacturer may not be held liable for anymanufacturer may not be held liable for any
manufacturer may not be held liable for any
damage resulting from improper, incorrect anddamage resulting from improper, incorrect and
damage resulting from improper, incorrect anddamage resulting from improper, incorrect and
damage resulting from improper, incorrect and
unreasonable use of the appliance.unreasonable use of the appliance.
unreasonable use of the appliance.unreasonable use of the appliance.
unreasonable use of the appliance.
GB
13
Switching the appliance off
Disconnect your appliance from the electricity
supply before carrying out any work on it.
Cleaning the appliance
! Never use steam cleaners or pressure cleaners on
the appliance.
The stainless steel or enamel-coated external
parts and the rubber seals may be cleaned using
a sponge that has been soaked in lukewarm water
and neutral soap. Use specialised products for
the removal of stubborn stains. After cleaning,
rinse well and dry thoroughly. Do not use abrasive
powders or corrosive substances.
The hob grids, burner caps, flame spreader rings
and burners may be removed to make cleaning
easier; wash them in hot water and non-abrasive
detergent, making sure all burnt-on residue is
removed before drying them thoroughly.
For hobs with electronic ignition, the terminal part
of the electronic lighting devices should be
cleaned frequently and the gas outlet holes
should be checked for blockages.
The inside of the oven should ideally be cleaned
after each use, while it is still lukewarm. Use hot
water and detergent, then rinse well and dry with
a soft cloth. Do not use abrasive products.
Clean the glass part of the oven door using a
sponge and a non-abrasive cleaning product,
then dry thoroughly with a soft cloth. Do not use
rough abrasive material or sharp metal scrapers
as these could scratch the surface and cause the
glass to crack.
The accessories can be washed like everyday
crockery, and are even dishwasher safe.
Inspecting the oven seals
Check the door seals around the oven regularly. If
the seals are damaged, please contact your nearest
Authorised After-sales Service Centre. We
recommend that the oven is not used until the seals
have been replaced.
Replacing the oven light bulb
1. After disconnecting the oven from the electricity
mains, remove the glass lid covering the lamp
socket (
see figure
).
2. Remove the light bulb and
replace it with a similar one:
voltage 230 V, wattage 25 W, cap
E 14.
3. Replace the lid and reconnect
the oven to the electricity supply.
Gas tap maintenance
Over time, the taps may become jammed or difficult
to turn. If this occurs, the tap must be replaced.
! This procedure must be performed by a
qualified technician who has been authorised by
the manufacturer.
Assistance
Please have the following information to hand:
The appliance model (Mod.).
The serial number (S/N).
This information can be found on the data plate
located on the appliance and/or on the packaging.
Care and maintenance
*
Only available in certain models.
PL
KUCHENKA I PIEKARNIK
Spis treści
Instalacja, 15-18
Ustawienie i wypoziomowanie
Podłączenie do sieci elektrycznej
Podłączenie gazu
Dostosowanie do różnych rodzajów gazu
Tabela charakterystyk palników i dysz
Dane techniczne
Opis urządzenia, 19
Widok ogólny
Panel sterowania
Uruchomienie i użytkowanie, 20-24
Użytkowanie płyty grzejnej
Użytkowanie piekarnika
Stosować regulator czasowy końca pieczenia
Programy pieczenia
Praktyczne porady dotyczące pieczenia
Programowanie pieczenia z użyciem programatora
elektronicznego
Tabela pieczenia
Zalecenia i środki ostrożności, 25-26
Ogólne zasady bezpieczeństwa
Zalecenia dotyczące odpadów
Oszczędność i ochrona środowiska
Konserwacja i utrzymanie, 26
Odłączenie prądu elektrycznego
Czyszczenie urządzenia
Sprawdzać uszczelki piekarnika
Wymiana żarówki oświetleniowej w piekarniku
Konserwacja kurków gazowych
Serwis Techniczny
Instrukcja obsługi
English, 1
PL
Polski, 14
GB
K6G56S.A /U
K6G52.A /U
K6G52.S A /U
KN6G62SA /U
KN6G66SA /U
KN6G660SA /U
PL
15
! Zachować niniejszą książeczkę instrukcji by móc
konsultować w przyszłości w dowolnej chwili. W
przypadku sprzedaży, odstąpienia lub przeniesienia
urządzenia, należy upewnić się, czy instrukcja
została przekazana wraz z nim.
! Należy uważnie przeczytać instrukcję: zawiera ona
ważne informacje dotyczące instalacji, użytkowania i
bezpieczeństwa.
! Instalacja urządzenia powinna zostać wykonana
zgodnie z niniejszymi instrukcjami i przez
wykwalifikowany personel.
! Wszelkie działania w zakresie regulacji lub
konserwacji muszą być wykonywane przy kuchence
odłączonej od zasilania elektrycznego.
Wentylacja pomieszczeń
Urządzenie może zostać zainstalowane wyłącznie w
pomieszczeniach ze stałą wentylacją, zgodnie z
obowiązującymi normami krajowymi. W
pomieszczeniu, w którym jest instalowane urządzenie,
musi być zapewniony taki dopływ powietrza, jaki jest
niezbędny dla prawidłowego spalania gazu (natężenie
przepływu powietrza nie powinno być niższe od 2 m
3
/h
na kW zainstalowanej mocy).
Wloty powietrza, zabezpieczone przez kratki,
powinny mieć przewód o przekroju użytkowym co
najmniej 100 cm
2
i powinny zostać rozmieszczone
tak, aby nie mogły ulec nawet częściowemu zatkaniu
(patrz rysunek A).
Wymiar tych wlotów powinien zostać zwiększony o
100% do minimum 200 cm
2
jeśli płyta robocza
urządzenia nie posiada urządzenia zabezpieczającego
przed brakiem płomienia i kiedy dopływ powietrza
następuje w sposób niebezpośredni z przyległych
pomieszczeń (patrz rysunek B) o ile nie one
częściami wspólnymi budynku, pomieszczeniami
zagrożonymi pożarem lub sypialniami
wyposażonych w przewód wentylacyjny z wyjściem
na zewnątrz, jak opisano powyżej.
Pomieszczenie przyległe
Pomieszczenie przeznaczone do przewietrzania
A. B
! Po dłuższym użytkowaniu urządzenia zaleca się
otwarcie okna lub zwiększenie prędkości
ewentualnych wentylatorów.
Odprowadzanie spalin
Odprowadzanie spalin musi być zapewnione przez
okap połączony z kominem o ciągu naturalnym i o
sprawnym działaniu lub przez wentylator elektryczny,
który włącza się automatycznie przy każdym
uruchomieniu urządzenia (patrz rysunki).
! Skroplone gazy pochodne ropy naftowej, cięższe od
powietrza, opadają w dół, dlatego pomieszczenia, w
których znajdują się butle GPL, powinny być
wyposażone w otwory wychodzące na zewnątrz,
umożliwiające odpływ dołem ewentualnych wycieków
gazu.
Butle GPL, niezależnie od tego czy puste, czy
częściowo napełnione, nie powinny być instalowane
ani składowane w pomieszczeniach lub wnękach
położonych poniżej poziomu podłogi (piwnice, itp.).
W pomieszczeniu należy przechowywać jedynie
aktualnie użytkowaną butlę, z dala od źródeł ciepła
(piece, kominki, piecyki), mogących doprowadzić do
wzrostu jej temperatury powyżej 50°C.
Ustawienie i wypoziomowanie
! Możliwe jest zainstalowanie urządzenia obok mebli,
których wysokość nie przekracza poziomu
roboczego.
! Należy upewnić się, czy ściana stykająca się z
tyłem urządzenia wykonana jest z materiału
niepalnego i odpornego na ciepło (T 90°C).
Dla zapewnienia prawidłowej instalacji:
ustawić urządzenie w kuchni, w jadalni lub w
innym pomieszczeniu (nie w łazience);
jeśli płaszczyzna kuchenki jest wyższa w
stosunku do płaszczyzny mebli, powinny one
zostać umieszczone w odległości co najmniej 600
mm od urządzenia;
jeśli kuchenka jest instalowana pod szafką wiszącą,
powinna ona znajdować się w odległości minimum
Instalacja
A
Otwarcie wentylacji dla
powietrza do spalania
Zwiększenie szczeliny
pomiędzy drzwiami a podłogą
Odprowadzanie
bezpośrednio na
zewnątrz
Odprowadzanie przez komin lub
rozgałęziony kanał dymowy
(wyłącznie do urządzeń
kuchennych)
16
PL
420 mm od płyty
kuchenki.
Odległość ta powinna
wynosić 700 mm, jeśli
szafki wiszące
łatwopalne (patrz
rysunek);
nie umieszczać
zasłon za kuchenką,
ani w odległości
mniejszej niż 200 mm
od jej krawędzi;
ewentualne okapy powinny zostać zainstalowane
według zaleceń odpowiedniej instrukcji.
Wypoziomowanie
Jeśli konieczne jest
wypoziomowanie urządzenia,
należy przykręcić nóżki
regulacyjne, dostarczane jako
wyposażenie, w odpowiednich
gniazdach umieszczonych w
rogach podstawy kuchenki
(patrz rysunek).
Nóżki* mocowane w
otworach pod podstawą
kuchenki.
Podłączenie do sieci elektrycznej
Zamocować na przewodzie znormalizowaną wtyczkę
dostosowaną do obciążeń wskazanych na tabliczce
znamionowej umieszczonej na urządzeniu (patrz
tabela Dane techniczne).
W przypadku bezpośredniego podłączenia do sieci
koniecznym jest zainstalowanie pomiędzy
urządzeniem a siecią wyłącznika polowego z
otwarciem minimalnym pomiędzy stykami 3 mm
przeznaczonego do obciążeń i odpowiadającego
obowiązującym normom (przewód uziemienia nie
powinien być przerywany przez wyłącznik). Przewód
zasilania powinien być umieszczony tak, aby w
żadnym punkcie jego temperatura nie przekraczała
temperatury otoczenia o 50°C.
Przed wykonaniem podłączenia należy upewnić się, czy:
gniazdko posiada odpowiednie uziemienie i jest
zgodne z obowiązującymi przepisami;
gniazdko jest w stanie wytrzymać maksymalne
obciążenie mocy urządzenia, wskazane na
tabliczce znamionowej;
napięcie zasilania odpowiada wartościom podanym
na tabliczce znamionowej;
HOOD
420
Min.
min. 650 mm. with hood
min.
700 mm. without hood
mm.
600
Min. mm.
420
Min. mm.
gniazdko jest kompatybilne z wtyczką urządzenia.
Jeśli gniazdko nie jest kompatybilne, wymienić
gniazdko lub wtyczkę; nie stosować przedłużaczy
ani rozgałęźników.
! Po zainstalowaniu urządzenia przewód elektryczny
i gniazdko prądu powinny być łatwo dostępne.
! Kabel nie powinien mieć zgięć, ani nie powinien
być zgnieciony.
! Przewód musi być okresowo sprawdzany i
wymieniany wyłącznie przez autoryzowany personel
techniczny.
! W przypadku nie przestrzegania powyższych
warunków producent zwolniony zostanie z
wszelkiej odpowiedzialności.
Podłączenie gazu
Podłączenie do sieci gazowej lub do butli gazowej
może być wykonane przy pomocy przewodu
giętkiego gumowego lub stalowego, zgodnie z
obowiązującymi normami krajowymi oraz po
upewnieniu się czy urządzenie jest wyregulowane
odpowiednio dla typu gazu, którym będzie zasilane
(patrz etykieta kalibracyjna na pokrywie: w
przeciwnym razie patrz niżej). W przypadku
zasilania płynnym gazem z butli, stosować
regulatory ciśnienia zgodne z obowiązującymi
normami krajowymi. Dla ułatwienia podłączenia
zasilanie gazem może być skierowane bocznie*:
zastąpić złączkę przewodu giętkiego zatyczką i
wymienić uszczelkę, dostarczaną jako wyposażenie.
! Dla zapewnienia bezpieczeństwa pracy,
odpowiedniego zużycia energii i zwiększenia trwałości
urządzenia, należy się upewnić czy ciśnienie
zasilania mieści się w granicach wskazanych w tabeli
Charakterystyka palników i dysz (patrz niżej).
Podłączenie gazu przy pomocy przewodu
gumowego
Sprawdzić czy przewód odpowiada obowiązującym
normom krajowym. Wewnętrzna średnica przewodu
powinna wynosić: 8 mm przy zasilaniu gazem
płynnym; 13 mm przy zasilaniu metanem.
Po wykonaniu podłączenia upewnić się czy przewód:
nie styka się w żadnym punkcie z częściami,
które osiągają temperatury przekraczające 50°C;
nie jest narażony na naciągnięcie ani poskręcanie
i nie ma na nim zagięć lub przewężeń;
nie ma styczności z przedmiotami tnącymi,
ostrymi krawędziami, ruchomymi częściami i nie
jest przygnieciony;
jest łatwo dostępny na całej długości dla
umożliwienia wykonywania kontroli jego stanu;
PL
17
jego długość wynosi mniej niż 1500 mm;
jest dobrze umocowany na dwóch końcach za
pomocą odpowiednich zacisków mocujących,
zgodnych z obowiązującymi normami krajowymi.
! Jeśli nie może być spełniony jeden z tych
warunków lub ich większa liczba, albo jeśli kuchenka
jest instalowana zgodnie z warunkami klasy 2 -
podklasy 1 (urządzenie umiejscowione pomiędzy
dwoma meblami), należy zastosować przewód giętki
stalowy (patrz niżej).
Podłączenie gazu przy pomocy przewodu
giętkiego ze stali nierdzewnej o pełnych
ściankach z gwintowanymi złączami.
Sprawdzić czy przewód i uszczelki odpowiadają
obowiązującym normom krajowym.
Aby zamontować przewód należy usunąć złączkę
przewodu giętkiego znajdującą się na urządzeniu
(złącze wejściowe gazu do urządzenia jest
gwintowane gwintem gazowym 1/2 walcowym
męskim).
! Wykonać podłączenie tak, aby całkowita długość
przewodów nie przekraczała 2 metrów oraz upewnić
się czy przewód nie styka się z ruchomymi
częściami i czy nie jest przygnieciony.
Kontrola szczelności
Po zakończeniu instalacji sprawdzić szczelność
wszystkich złącz stosując w tym celu roztwór
mydlany, nigdy płomień.
Dostosowanie do różnych rodzajów gazu
Urządzenie może być dostosowane do innego
rodzaju gazu niż ten, którym jest aktualnie zasilane
(wskazany na etykiecie kalibracyjnej na pokrywie).
Dostosowanie płyty grzejnej
Wymiana dysz palników płyty:
1. zdjąć kratki i wykręcić
palniki z gniazd;
2. odkręcić dysze, posługując
się kluczem rurowym 7 mm
(patrz rysunek) i wymienić je
na te, które przystosowane
do nowego rodzaju gazu (patrz
tabela Charakterystyka
palników i dysz);
3. przywrócić na swoje miejsce wszystkie
komponenty wykonując czynności w kolejności
odwrotnej w stosunku do powyższej sekwencji.
! Palniki płyty nie wymagają regulacji powietrza
pierwotnego.
! Po wykonaniu regulacji dla gazu innego niż
oryginalnie przewidziany, należy wymienić
poprzednią etykietę kalibracyjną na etykietę
odpowiadającą nowemu gazowi, dostępną w naszych
Autoryzowanych Centrach Obsługi Technicznej.
! W sytuacji, gdy ciśnienie gazu jest inne (lub
zmienne) od przewidzianego, konieczne jest
zainstalowanie na przewodach doprowadzających
regulatora ciśnienia, zgodnie z obowiązującą normą
krajową dotyczącą „kanałowych regulatorów gazu”.
18
PL
Tabela charakterystyk palników i dysz
S
S
R
A
K6G56S.A /U
K6G52.A /U
K6G52.S A /U
KN6G62SA /U
KN6G66SA /U
Tabela 1 (dla Polski) G30 (GPB-B) G20 (GZ50) G2.350 (GZ35)
Palnik
Średnica
(mm)
Moc
cieplna
(p.c.i.*)
kW
Moc
cieplna
(p.c.i.*)
kW
By-
pass
1/100
Dysza
1/100
(mm)
Przepływ
*
l/godz
Moc
cieplna
(p.c.i.*)
kW
Dysza
1/100
(mm)
Przepływ
*
l/godz
Moc
cieplna
(p.c.i.*)
kW
Dysza
1/100
(mm)
Przepływ
*
l/godz
Duży (R) 100 0,70 3,40 41 86 247 2,90 116 276 2,90 183 384
łszybki
(średni) (S)
75 0,40 2,20 30 70 160 1,90 106 181 1,90 143 251
Pomocniczy
(mały) (A)
55 0,40 1,10 30 50 80 1,00 79 95 1,00 106 132
Ciśnienia
zasilania
minimalne (mbar)
nominalne (mbar)
maksymalne (mbar)
29
37
44
16
20
25
10
13
16
* A 15°C e 1013 mbar – gaz suchy
G20 (GZ50) p.c.i. = 35.9 MJ/m³
G2.350 (G2-350) p.c.i. = 25.8 MJ/m³
G30 (GPB-B) p.c.i. = 123.6 MJ/m³
DANE TECHNICZNE
Wymiary
piekarnika W x D
x G
40x43,5x32 cm
Objętość
(l) 56
Wymiary
użytkowe
szuflady do
podgrzewania
potraw
szerokość (cm) 46
głębokość (cm) 44
wysokość (cm) 8,5
Palniki
mogą być dostosowane do
wszystkich rodzajów gazu
wskazanych na tabliczce
znamionowej
Napięcie i
częstotliwość
zasilania
elektrycznego
patrz tabliczka znamionowa
ENERGY LABEL
Dyrektywa 2002/40/WE na
etykiecie piekarniw elektrycznych
Norma EN 50304 Zużycie energii
konwekcja naturalna — funkcja
ogrzewania: Tradycyjne;
Zużycie energii deklaracja Klasa
konwekcji wymuszona — funkcja
ogrzewania: Pieczenie ciasta
Dyrektywy unijne: 2006/95/EC z
dnia 12/12/06 (niskie napięcie) z
źniejszymi zmianami - 04/108/EC
z dnia 15/12/04 (zgodność
elektromagnetyczna) z
źniejszymi zmianami -
93/68/EEC z dnia 22/07/93 z
źniejszymi zmianami,
2009/142/EC z dnia 30/11/09 (gaz)
z późniejszymi zmianami, -
93/68/EEC z dnia 22/07/93 z
źniejszymi zmianami, -
2002/96/EC.
1275/2008 (Stand-by/ Off mode)
KN6G660SA /U
PL
19
Opis urządzenia
Widok ogólny
Panel sterowania
*
Tylko w niektórych modelach.
Pokrętło
REGULATORA CZASOWEGO KOŃCA PIECZENIA*
Kontrolka
TERMOSTATU
Pokrętła
PALNIK
ALNIK
ÓW
płyty grzejnej
Elektroniczny
programator*
Ruszt
Szklana pokrywa*
Panel sterujący
Kratka piekarnika
Tacka na kapiący tłuszcz
lub do pieczenia
Prowadnice do wsuwania
rusztu i tacy
pozycja 3
pozycja 2
pozycja 1
Palnik gazowy
Płyta podpalnikowa
Regulowane nóżki
Regulowane nóżki
pozycja 5
pozycja 4
Pokrętło
REGULATORA CZASOWEGO KOŃCA PIECZENIA*
Kontrolka
TERMOSTATU
Pokrętła
PALNIK
ALNIK
ÓW
płyty grzejnej
Elektroniczny
programator*
20
PL
Uruchomienie i użytkowanie
Użytkowanie płyty grzejnej
Włączanie palników
Dla każdego pokrętła PALNIKA jest wskazany wypełnionym
kółkiem odpowiadający mu palnik.
W celu włączenia palnika na płycie grzejnej:
1. zbliżyć do palnika płomień lub zapalarkę;
2. nacisnąć i równocześnie przekręcić pokrętło PALNIK w
kierunku przeciwnym do ruchu wskazówek zegara na symbol
maksymalnego płomienia E.
3. ustawić żądany płomień, obracając pokrętłem PALNIK w
kierunku przeciwnym do ruchu wskazówek zegara: na minimum C,
na maksimum E lub na pozycję pośrednią.
Jeśli urządzenie jest wyposażone w zapłon elektroniczny*(C)
(patrz rysunek) wystarczy nacisnąć i równocześnie przekręcić
pokrętło PALNIK w kierunku przeciwnym do ruchu wskazówek
zegara na symbol maksymalnego płomienia, do zapalenia się
palnika. Może się zdarzyć, że palnik zgaśnie w chwili zwolnienia
pokrętła. W takim przypadku powtórzyć czynność, trzymając
pokrętło naciśnięte przez dłuższą chwilę.
! W razie przypadkowego zgaśnięcia płomienia wyłączyć palnik i
odczekać przynajmniej 1 minutę przed ponowieniem próby jego
zapalenia.
Jeśli palnik wyposażony jest w
urządzenie zabezpieczające(X)* przed
brakiem płomienia, należy przytrzymać
naciśnięte pokrętło PALNIKA przez około
3-7 sekund, aby utrzymać zapalony
płomień i uruchomić urządzenie.
W celu wyłączenia palnika przekręcić pokrętło do zatrzymania
•.
Praktyczne rady dotyczące użytkowania palników
Dla uzyskania lepszej wydajności palników oraz zminimalizowania
zużycia gazu należy stosować naczynia o płaskim dnie,
wyposażone w pokrywkę i o rozmiarach proporcjonalnych w
stosunku do rozmiarów palnika:
W celu zidentyfikowania rodzaju palnika należy zapoznać się z
rysunkami znajdującymi się w paragrafie „Charakterystyki
palników i dysz”.
Użytkowanie piekarnika
! Przy pierwszym włączeniu należy uruchomić pusty piekarnik na
przynajmniej jedną godzinę, z termostatem ustawionym na
maksimum i z zamkniętymi drzwiczkami. Następnie wyłączyć,
otworzyć drzwiczki piekarnika i przewietrzyć pomieszczenie.
Zapach, jaki się wytworzy, jest wynikiem parowania substancji
stosowanych w celu zabezpieczenia piekarnika.
! Przed użytkiem należy obowiązkowo usunąć folię plastikową ze
ścianek urządzenia!
! Aby skorzystać z elektrycznego piekarnika w urządzeniach
wyposażonych w programator elektroniczny należy równocześnie
nacisnąć przyciski
i (na wyświetlaczu pojawia się
wówczas symbol
), a następnie wybrać żądaną funkcję
pieczenia.
1. Wybrać żądany program pieczenia obracając pokrętłem
PROGRAMY.
2. Wybrać odpowiednią temperaturę obracając pokrętłem
TERMOSTAT. Wykaz potraw z zalecanymi dla nich temperaturami
znajduje się w Tabeli (patrz Programy).
3. Zapalona lampka kontrolna TERMOSTAT wskazuje fazę
rozgrzewania do zaprogramowanej temperatury.
4. Podczas pieczenia można zawsze wykonać następujące
czynności:
- zmienić program pokrętłem PROGRAMY;
- zmienić temperaturę pokrętłem TERMOSTAT;
- przerwanie pieczenia przez przestawienie pokrętła PROGRAMY
w położenie „0”.
! Nie stawiać nigdy żadnych przedmiotów na dnie piekarnika, aby
nie uszkodzić emalii.
! Naczynia do pieczenia stawiać zawsze na ruszcie znajdującym
się na wyposażeniu piekarnika.
Kontrolka TERMOSTAT
Jej zaświecenie się sygnalizuje, że piekarnik wytwarza ciepło.
Gaśnie, kiedy wewnątrz piekarnika osiągnięta zostaje ustawiona
temperatura. W tym momencie kontrolka zapala się i gaśnie
naprzemiennie, wskazując, że termostat pracuje i utrzymuje stałą
temperaturę.
Oświetlenie piekarnika
Zapala się je wybierając
8 8
8 8
8 przy pomocy pokrętła
PROGRAMY. Pozostaje załączone, gdy wybiera się
program pieczenia.
*
Znajduje się tylko w niektórych modelach.
Palnik ø Średnica naczyń (cm)
Szybki (R) 24 26
Średnio szybki (S) 16 – 20
Pomocniczy (A) 10 – 14
X
C
UWAGA! Szklana pokrywa może
popękać jeżeli zostanie nagrzana.
Należy wyłączyć wszystkie palniki
przed zamknięciem pokrywy.
*Dotyczy tylko modeli ze szklana
pokrywa.
1 / 1

Indesit K6G56S.A (X)/U instrukcja

Kategoria
Mikrofale
Typ
instrukcja
Ten podręcznik jest również odpowiedni dla

w innych językach