Novus NVR-6332-H2/F Instrukcja obsługi

N CONTROL 6000

U s e r ’ s m a n u a l

N Control 6000 - User’s manual ver. 1.2.1

2

TABLE OF CONTENTS

TABLE OF CONTENTS ...................................................................................... 2

1. FOREWORD INFORMATION ...................................................................... 3

1.1. Main characteristics ..................................................................................... 3

1.2. Recommended PC specification .................................................................. 3

2. INSTALLATION AND LAUNCHING SOFTWARE ................................... 4

2.1. Installation of the software .......................................................................... 4

2.2. Software startup ........................................................................................... 6

2.3. Login window .............................................................................................. 6

2.4. Record parition settings ............................................................................... 8

2.5. Application interface ................................................................................... 9

2.6. Server processes ........................................................................................ 11

3. BASIC FUNCTIONALITY SUPPORT ........................................................ 12

3.1. Device adding ............................................................................................ 12

3.2. Change the dvice’s IP address ................................................................... 14

3.3. Manually adding a device ......................................................................... 14

3.4. Adding devices to the zone ....................................................................... 15

3.5. Removing a dvice from the list. ................................................................ 15

4. DISPLAYING IMAGES FROM DEVICES ................................................ 16

4.1. Live view .................................................................................................. 16

4.2. Records playback ...................................................................................... 19

4.3. Copying recordings from the playback window ....................................... 21

4.4. Copying recordis to the remote device ..................................................... 23

N Control 6000 - User’s manual ver. 1.2.1

3

FOREWORD INFORMATION

1. FOREWORD INFORMATION

1.1. Main characteristics

• Software used for connections to 6000 series NOVUS NVRs & NHDRs.

• Multiscreen environment;

• Group device management;

• Advanced user management;

• Site maps features;

• Local record and playback;

• H.265 and H.264 compression;

• Support of alarm event scenerios;

1.2. Recommended PC specification

The PC hardware requirements are listed below:

1. Intel i3 CPU Processor or higher. I5-7400 3.0GHz recommended.

2. RAM memory DDR3 4 GB. 16GB recommended.

3. OS : Windows10 (32bit\64bit) Pro, Windows8 (32bit\64bit)

4. Network adaptor 100/1000 Mb/s

5. Graphic card NV GT430, AMD HD6570 or better. Nvidia GeForce GTX1060 6GB

recommended.

6. . Hard disk 500 GB SATA minimum.

N Control 6000 - User’s manual ver. 1.2.1

4

INSTALLATION AND LAUNCHING OF THE SOFTWARE

2. INSTALLATION AND LAUNCHING OF THE SOFTWARE

2.1. Installation of the software.

Download N Comtrol 6000 from www.novuscctv.com and save it on the local drive. Run the software

to begin the installation. Setup windows is displayed (as shown below). Press OK to continue, or

Cancel to exit installation.

After confirming the language selection, the installer prepares the Installation Wizard.

Select the installation path. Press the Browse button to select new installation folder. Press Next to

continue. The default paht is C:\Program Files (x86)\Novus\N Control 6000.

N Control 6000 - User’s manual ver. 1.2.1

5

INSTALLATION AND LAUNCHING OF THE SOFTWARE

After selecting the installation path, the program installs automatically. When the operation is

complete the window below appears.

Choose Lanuch Software to open program automatically after clicking Finish button.

N Control 6000 - User’s manual ver. 1.2.1

6

SOFTWARE STARTUP

2.2. Software startup

The N Control 6000 program can be started by clicking on the MonitorClient.exe file (in the directory

where installed software) or with the N Control 6000 Client icon located on

desktop.

2.3. Login window

After starting the software, the login window appears.

User name - select user from the list. At first start here is only a super administrator account available

called root. After adding more users, with the first time you log in, enter their name. The next time

you log in, they will be on the list choice.

Password - a place to enter the password of the selected user. Default administrator password is pass.

Remember Password - the option saves the password in the program, the user will not need it

type next time

Auto Login - the option saves the password in the program, the user will not need to

type it next time

Login – logging into the account of the indicated user.

Cancel - resignation from starting the software.

Reset password - the option to give a new password to the super administrator account. At

the first login is not available. To use this option, you must first select 3 security questions

and define the answers.

N Control 6000 - User’s manual ver. 1.2.1

7

SOFTWARE STARTUP

After pressing the Reset password button, the following window appears.

After pressing the Search button, the defined security questions appear. Questions

are defined in the Accounts and permissions section, User Account Settings tab, button

Edit security questions.

After correctly filling in the answer and pressing the OK button, a window with fields for entering a

new password appears.

After entering the new password twice, you can log into the software. All user account settings can be

changed in the Accounts and Permissions section.

N Control 6000 - User’s manual ver. 1.2.1

8

SOFTWARE STARTUP

2.4. Record partition settings

During the first run (or when we do not select a partition). After logging in, the application will

display the window for selecting the partition for saving the recordings by the program. In the

program window, select the partition on which the program is to save by marking the checkbox and

pressing the OK button.

It is not recommended to select the system partition or with less than 50 Gb of free space. Saving

recordings on the system partition may cause partition overflow and unstable system operation.

Therefore, after selecting the system partition, a warning window will appear. Clicking the OK button

will confirm the selection and clicking the Cancel button will cancel the selection.

N Control 6000 - User’s manual ver. 1.2.1

9

APPLICATION INTERFACE

2.5. Application interfaace

Panels - displays the icons of the currently open application panels. By clicking on the panel icon it

appears in the main window.

The + button opens a new live camera view window. After enter in particular settings, when a new

camera preview window is opened, more are added on the bar icons. They can be closed with a cross

in the corner of the icon (it appears when you hover over the icon). Individual panels can be moved as

a separate application window to another monitor.

Menu - allows you to switch between live view (View), enter settings available functions (System

Settings) or checking the software information (Help).

Main window - active panel displayed. The initial Start panel displays a list of panels

grouped in sections.

Information bar - displays the authentication server IP address, communication port, name

logged in user, unit load level (CPU and memory), current date and time.

The red color of the unit load level additionally warns against overload.

Alarm Icon - allows you to quickly display a list of current alarms.

Panels Top menu

Information bar

Alarm Icon

N Control 6000 - User’s manual ver. 1.2.1

10

APPLICATION INTERFACE

The Start panel shows 6 sections at the beginning. The last section Functional Selection allows you

to enable and turn off individual sections. After clicking on this section, the following window

appears:

Live view, Storage playback, Resource management sections are mandatory.

The other sections can be turned on as an option for setting up, and turned off when they are not

needed.

There are buttons at the top of the window:

• Select All - selects all possible options.

• Reverse - inverts the selected selection (except for sections that cannot be switched).

• Clear All - deselects all sections.

After enabling all options, we have a maximum of 12 sections with all possible functions.

N Control 6000 - User’s manual ver. 1.2.1

11

SERVER PROCESSES

2.6. Server processes

When the N Control 6000 software is started, server processes are started in the background.

They can be viewed using the N control 6000 Server icon in the right part of the taskbar.

After clicking on the icon, a window showing the status of server processors appears. Clicking the

Stop All button stops all N Control processes . After clicking Start All N control processes should

start.

After clicking the Configure button, a window for specifying the port for the service will open.

Star/Stop button Reboot All

N Control 6000 - User’s manual ver. 1.2.1

12

BASIC FUNCTIONS

3. Basic functionality support.

3.1. Device adding

To add a device, find the Resource Management section

To add a device, find the Resource Management section add click on Add, Edit or Deleted Device.

In the window that appears, click the Add button in Encoding device

A list of devices found by the program will be displayed in the window. To add a device from the list

they should be marked with a checkmark in the selection field of the first column to the right of the

list and then clicking the OK button.

N Control 6000 - User’s manual ver. 1.2.1

13

BASIC FUNCTIONS

If the device has been correctly added, the device data will be displayed in black. A gray color in the

data line and a status other than Online in the Online Status column means that the device has failed

to connect.

To edit device parameters, click on the field in the Edit column.

In the opened window, you can edit connection parameters such as Port, Username, Password and

IP Address. After making changes, press the OK button to save the parameters.

N Control 6000 - User’s manual ver. 1.2.1

14

BASIC FUNCTIONS

3.2. Change the device's IP address

The device's IP address can be changed in the device search window before adding. Click on the

ModifyIP Address field.

In the opened window, you can modify the following data: IP address, Mask, Gateway, Port, User

name and Password. The network settings will be changed after pressing the OK button, if the

credentials provided in the User name and Password fields are correct.

3.3. Manually adding a device.

To add a device to the program that is not searched, e.g. outside the local network, select the Manual

adding tab in the search engine.

N Control 6000 - User’s manual ver. 1.2.1

15

BASIC FUNCTIONS

The following address specification modes to connect to the device are available in the IP Address /

IP Range / Domain Name / URL column:

IP address - The address of a single device given as decimal numbers

IP range - allows you to add more devices by specifying a range of IP addresses including the first

and last addresses. Devices will be added with each available address between the ranges given.

Domain name - allows you to enter an address using the domain name changed into an IP address

using the DNS service

URL - Enter a URL to the RTSP streaming device.

After defining the address to connect to the device, in the Protocol field, select Standard device for

the recorder or camera, and in the Ports field, enter the data port (by default 6036 for the recorder,

9008 for the camera). Enter the login details in the User name and Password fields. After clicking the

Test connection button, the program will check the connection. If the test is successful, press the OK

button to save the parameters.

3.4. Adding devices to the zone.

The program has a defined default zone Default area to which devices are added, unless we define

other zones. To add a zone, click on the Create zone button in search device window. In the opened

window, select the Parent Zone and enter the required zone name in the Zone name field. When

adding a device, in the Select zone field you can select the zone to which the device is to be added.

To transfer an already existing device, select the check box on the device list and click the Select

Area button.

After selecting the target zone and pressing the OK button, the device will be moved to another zone.

3.5. Removing a device from the list.

To delete devices, select devices on the list and click the Delete button. In the window that opens,

confirm your choice by clicking the OK button.

N Control 6000 - User’s manual ver. 1.2.1

16

BASIC FUNCTIONS

4. Displaying images from devices

4.1. Live view

To switch to the image display, select from the bar at the top of the screen or

select Live View form menu.

Channel list to be displayed Channel display window

Channel display window

N Control 6000 - User’s manual ver. 1.2.1

17

BASIC FUNCTIONS

In the tab with the list of channels, expand the list of devices by clicking on the + field. From the

expanded list devices, drag the selected channels while holding the left button to the display

windows .

Positioning the mouse cursor at the bottom of

the display window opens the display menu.

The display options are available after pressing

the right mouse button on the displayed screen

N Control 6000 - User’s manual ver. 1.2.1

18

BASIC FUNCTIONS

The selection of divisions is available after clicking

on the icon of one of the divisions

After clicking the button for additional divisions a window with additional divisions is

displayed.

Additionally, the following settings are available on the bar:

- displaying video images in full screen

- enabling / disabling OSD display in video windows

- enable audio broadcasting from selected devices

- manual activation of alarm outputs on connected devices

- enable / disable display of detection areas

- disable display for all cameras in the window

- saves display layout

- selection allows you to manually select the type of stream

displayed in the window.

N Control 6000 - User’s manual ver. 1.2.1

19

BASIC FUNCTIONS

4.2. Records playback

To run the recordings playback window, click on the Record playback in Storage Playback menu.

The recordings playback panel is displayed then.

Recordings calendar

Video display window Device list tree

Recording strips

N Control 6000 - User’s manual ver. 1.2.1

20

BASIC FUNCTIONS

In the lower left corner of the program there is an icon in which the settings mean the program has

play recordings from external devices such as recorders or use the recordings saved by the program on

the selected partition.

- selects recordings from external devices

- selects playback of recordings saved in the client software

To view the recordings, move the name of the selected channel from the list on the left while holding

left mouse button to right video window. At the bottom of the menu, a bar is displayed specifying the

length of available recordings for the selected day. To change the day of playback, select it in the

calendar window. Days for which devices with recordings are marked in blue.

Clicking on the calendar opens the day and displays a bar of available recordings. Clicking on the bar

starts playback at the selected point in time. The colors of the record bar indicate the type of

recordings according to the descriptions at the bottom of the playback window.

In the record control bar there are buttons for selecting splits and controls displaying images in

windows.

The following buttons are used to control playback

- Rewind

- Slow playback

- Stop playback

Strona się ładuje...

Novus NVR-6332-H2/F Instrukcja obsługi

Novus NVR-6332-H2/F Instrukcja obsługi

w innych językach

Powiązane artykuły

Inne dokumenty