Novus NVR-6332P16-H4/F Instrukcja obsługi

U s e r ’s m a n u a l

(s h ort )

NVR-6332P16-H4

NVR-6332P16-H4 User’s manual (Short) ver.1.0

2

IMPORTANT SAFEGUARDS AND WARNINGS

EMC (2004/108/EC) and LVD (2006/95/EC ) Directives CE Marking

Our products are manufactured to comply with requirements of following directives and national regulations implementing the

directives:

Electromagnetic compatibility EMC 2004/108/EC; Low voltage LVD 2006/95/EC with further amendment. The Directive

applies to electrical equipment designed for use with a voltage rating of between 50VAC and 1000VAC as well as 75VDC and

1500VDC.

WEEE Directive 2002/96/EC Information on Disposal for Users of Waste Electrical and Electronic Equipment

This appliance is marked according to the European Directive on Waste Electrical and Electronic Equipment (2002/96/EC)

and further amendments. By ensuring this product is disposed of correctly, you will help to prevent potential negative consequences for

the environment and human health, which could otherwise be caused by inappropriate waste handling of this product.

The symbol on the product, or the documents accompanying the product, indicates that this appliance may not be treated as household

waste. It shall be handed over to the applicable collection point for the waste electrical and electronic equipment for

recycling purpose. For more information about recycling of this product, please contact your local authorities, your

household waste disposal service or the shop where you purchased the product.

RoHS Directive 2002/95/EC

Concerning for human health protection and friendly environment, we assure that our products falling under RoHS Directive

regulations, regarding the restriction of the use of hazardous substances in electrical and electronic equipment, were

designed and manufactured in compliance with mentioned regulation. Simultaneously, we claim that our products were

tested and do not contain hazardous substances exceeding limits which could have negative impact on human health or

natural environment.

Information

The device, as a part of professional CCTV system used for surveillance and control, is not designed for self installation in households

by individuals without technical knowledge. The manufacturer is not responsible for defects and damages resulted from improper or

inconsistent with user ’ s manual installation of the device in the system.

ATTENTION!

PRIOR TO UNDERTAKING ANY ACTION THAT IS NOT PROVISIONED FOR THE GIVEN PRODUCT IN ITS USER ’ S MANUAL AND

OTHER DOCUMENTS DELIVERED WITH THE PRODUCT, OR THAT ARISES FROM THE NORMAL APPLICATION OF THE PRODUCT, ITS

MANUFACTURER MUST BE CONTACTED OR THE RESPONSIBILITY OF THE MANUFACTURER FOR THE RESULTS OF SUCH AN

ACTION SHELL BE EXCLUDED.

1. Prior to undertaking any action please consult the following manual and read all the safety and operating instructions before

starting the device.

2. Please keep this manual for the lifespan of the device in case referring to the contents of this manual is necessary;

3. All the safety precautions referred to in this manual should be strictly followed, as they have a direct influence on user ’ s safety

and durability and reliability of the device;

4. All actions conducted by the servicemen and users must be accomplished in accordance with the user ’ s manual;

5. The device should be disconnected from power sources during maintenance procedures;

6. Usage of additional devices and components neither provided nor recommended by the producer is forbidden;

7. You are not allowed to use the device in high humidity environment (i.e. close to swimming pools, bath tubs, damp basements);

8. Mounting the device in places where proper ventilation cannot be provided (e. g. closed lockers etc.) is not recommended since it

may lead to heat build -up and damaging the device itself as a consequence;

9. Mounting the device on unstable surface or using not recommended mounts is forbidden. Improperly mounted device may cause a

fatal accident or may be seriously damaged itself. The device must be mounted by qualified personnel with proper authorization, in

accordance with this user ’ s manual.

10. Device should be supplied only from a power sources whose parameters are in accordance with those specified by the producer in

the devices technical datasheet. Therefore, it is forbidden to supply the devices from a power sources with unknown parameters,

unstable or not meeting producer’ s requirements;

11. You cannot allow any metal objects get inside the recorder. It might cause serious damage. If a metal object gets inside the device

contact the authorised Novus service immediately.

12. The manufacturer does not bear responsibility for damage or loss of data stored on HDDs or other media occurred during the usage

of the product.

NVR-6332P16-H4 User’s manual (Short) ver.1.0

3

FOREWORD INFORMATION

1. FOREWORD INFORMATION

1.1. Network recorder’s technical data

NVR-6332P16H4

VIDEO

IP Cameras 32 channels at 2592 x 1944 resolution (video + audio)Edit feature

Supported Cameras/Protocols NOVUS, ONVIFEdit feature

Supported Resolution max. 2592 x 1944Edit feature

Compression H.264, H.264+, H.265Edit feature

Monitor Output main (split screen, full screen, sequence): 1 x VGA, 1 x HDMI (4K UltraHD) (up to 2 monitors simulta-

neously)Edit feature

Dualstreaming Support yes*Edit feature

AUDIO

Audio Output 1 x line-out (RCA) 1 x HDMIEdit feature

RECORDING

Recording Speed 960 kl/s (32 x 30 kl/s for 2592 x 1944)

Stream Size 256 Mb/s in total from all camerasEdit feature

Recording Mode time-lapse, triggered by: manual, alarm input, motion detectionEdit feature

Prealarm/Postalarm up to 5 s/up to 600 sEdit feature

DISPLAY

Display Speed 960 fps (32 x 30 fps)**Edit feature

PLAYBACK

Playback Speed 480 fps (16 x 30 fps for 2592 x 1944) **Edit feature

Recorded Data Search by date/time, eventsEdit feature

BACKUP

Backup Methods USB port (HDD or Flash memory), networkEdit feature

Backup File Format AVIEdit feature

STORAGE

Internal storage for recording available mount: 4 x HDD 3.5” 6 TB SATAEdit feature

Total Capacity 24 TBEdit feature

ALARM

Camera Alarm Input/Output supports camera’s alarm input/output *Edit feature

Motion Detection supports camera’s motion detection*Edit feature

System Reaction to Alarm Events buzzer, e-mail, alarm output activation, recording activation, PTZEdit feature

NETWORK

Network Interface 1 x Ethernet - RJ-45 interface, 10/100/1000 Mbit/sEdit feature

Network Protocols Support HTTP, TCP/IP, IPv4, DHCP, DNS, DDNS, NTP, UPnP, SMTPEdit feature

ONVIF Protocol Support Profile S (ONVIF 2.2 or higher)Edit feature

PC/MAC Software Internet Explorer, NVR-6000 Viewer/SafariEdit feature

Smartphone Software SuperLive Plus (iPhone, Android)Edit feature

Max. Number of Connections with NVR 2Edit feature

Bandwidth 256 Mb/s in total to all client workstationsEdit feature

PTZ

PTZ Functions pan/tilt/zoom, preset commands*Edit feature

AUXILIARY INTERFACES

USB Ports 1 x USB 2.0, 1 x USB 3.0Edit feature

OPERATING SYSTEM

Operating System LinuxEdit feature

Operation Mode triplexEdit feature

OSD languages: Polish, English, othersEdit feature

Control PC mouse and IR remote controller (in-set included), networkEdit feature

System Diagnostic automatic control of: HDDs, network, camera connection lossEdit feature

Security password protection, IP filtering, MAC filteringEdit feature

INSTALLATION PARAMETERS

Dimensions (mm) 440 (W) x 70 (H) x 390 (D)Edit feature

Weight 4.4 kg (without HDD)Edit feature

Power Supply 100 ~ 240 VACEdit feature

Power Consumption 60 W (with 4 HDDs) + 246 W PoEEdit feature

Operating Temperature -10°C ~ 50°CEdit feature

NVR-6332P16-H4 User’s manual (Short) ver.1.0

4

FOREWORD INFORMATION

1.2. Main characteristics

 Supports resolution up to 2592 x 1944

 Supported protocols: ONVIF

 Recording up to 2592 x 1944

 Recorded stream size up to 256 Mb/s in total from all cameras

 Internal HDDs mount up to 4

 16 x Ethernet PoE (IEEE802.3af-15.4W) - RJ-45, 10/100 Mbit/s

WARNING!

ONVIF protocol support was verified with IP cameras based on ONVIF ver. 2.2 and compatible

with the "PROFILE S".

Implementation of the ONVIF protocol by different manufacturers may vary by some functions,

which can make them work improperly or not in accordance with expectation. AAT HOLDING

Company is not responsible for incompatibility problems resulting from cameras of other brands

than NOVUS, which are using ONVIF protocol. If you are using ONVIF protocol cameras other

than NOVUS brand it is recommended to test each time whether required functions work

correctly.

1.3. Package contents

Unpack the device carefully. After unpacking, please ensure that package contains the following items:

 Network Video Recorder

 USB Mouse

 Remote control

 Power supply

 User’s manual (short)

If any of the elements has been damaged during transport, pack all the elements back into the original

packaging and contact your supplier.

NVR-6332P16-H4 User’s manual (Short) ver.1.0

5

STARTING THE DEVICE

2. STARTING THE DEVICE

2.1 Electrical connection and other back panel elements.

NVR-6332P16-H4

1. LAN: RJ-45 connector port to connect to the local network and internet.

2. HDMI: Main monitor connectors, use the HDMI cable to connect monitor.

3. USB: USB port for external Flash memory and other USB devices.

4. AUDIO IN: Audio mono inputs to connect microphones*.

5. POWER SOCKET: To plug in the 230 V power cord.

6. POWER SWITCH: Power switch

7. AUDIO OUT : Audio output

8. CONNECTORS : Block of alarm input/output connectors

9. VGA: Main monitor connectors, use the D-SUB VGA cable to connect monitor.

10. PoE PORTS: 16x RJ-45 connector ports with PoE support for IP cameras

* Will be available in the future.

4

3

2

1

8

10

5

9

7

6

NVR-6332P16-H4 User’s manual (Short) ver.1.0

6

STARTING THE DEVICE

2.2 HDD mounting

Novus NVR-6332P16-H4 supports 4 internal SATA HDDs.

WARNING!

In order to find information regarding the compatible models of HDDs and their maximum

capacities, please contact Novus distributor or check the information presented at

www.novuscctv.com. AAT HOLDING Company is not responsible for any problems from using

not recommended hard drives.

The list of compatible HDDs contains all the HDDs that can be used with a given DVR including

HDDs designed for office use - so called desktop disks. However, due to the fact that reliability of

the recording process and data safety are paramount factors of any CCTV system, we strongly

advise to use HDDs designed for continuous (24/7) operation.

You need to format disks if they were used in a different device. All data saved on HDD prior to

format will be lost.

HDDs Installation

In order to mount HDDs, please loose the screws in the locations shown on the picture below and

remove the cover.

WARNING: !

Before removing cover unplug the power cord from the NVR. When NVR is turned on before

disconnecting the power cord, shut down the recorder using the NVR menu.

If you use the disk previously used in another device, it is necessary to format it before using.

Formatting the drive erase all the data from disk. All drives in the recorder should be exactly the

same type.

NVR-6332P16-H4 User’s manual (Short) ver.1.0

7

STARTING THE DEVICE

Screw two screws into the holes of HDD but don’t tighten them.

Invert the case, slide the hard disk drive into the housing, hanging the screw heads in the wider holes of

the housing, and slide the disk so that the screws are in place to be tightened.

Then tighten the other screws to secure the hard drive. In the same way, connect the remaining disks.

NVR-6332P16-H4 User’s manual (Short) ver.1.0

8

STARTING THE DEVICE

Connect the power and signal cables to the hard disks and then close the casing and secure it by

screwing in the security screws.

2.3. Connecting the power supply.

Please connect provided power cord in the rear power port of the NVR like described below.

To start the unit turn on the power switch on back panel. Initialization lasts approximately 60 seconds.

During this time executing any device functions and pressing any buttons is prohibited. To shut down

the device please use the menu.

CAUTION:

Make connection when the power is not applied and the power switch is turned off.

Do not place the power cord under the carpet or rug. The power cord is usually earth-grounded.

However, even if it's not earth-grounded, never modify it on your own for earth-grounding.

Make sure that power adapter is placed near of NVR and secured from accidental disconnection.

If the device was brought from a location with lower temperature, please wait until it reaches the

temperature of location it is currently in. Turning the device on immediately after bringing it

from a location with lower ambient temperature is forbidden, as the condensing water vapour

may cause short-circuits and damage the device as a result.

Before starting the device familiarize yourself with the description and the role of particular

inputs, outputs and adjusting elements that the device is equipped with.

NVR-6332P16-H4 User’s manual (Short) ver.1.0

9

2.4. Connecting monitor

This product supports following interfaces for main monitor: HDMI, VGA.

For HDMI following resolutions are supported: 1280x1024, 1920x1080 i 3840x2160.

2.5. Connecting camera and Network

NVR-6332P16-H4 has built-in 16 PoE ports RJ-45 with PoE support, which can be used for

connecting cameras. Please notice that the Ethernet connection is effective within 100 meter distance.

To connect IP cameras please connect cables like on image and follow the described below.

We recommend that you configure the camera before connecting to a recorder, as described in the

user manual of the camera. Please note that cameras have addressed the unique IP address supported

by the recorder. Recorders with built-in PoE switches use a different address from the cameras

connected via the built-in switch and another to connect to a device connected via the LAN port.

Connecting cameras and network recorders NVR-6332P16-H4

STARTING THE DEVICE

KAMERY IP

NOVUS NVR

INTERNET

PC

NETWORK SWITCH

NETWORK CAMERAS

NVR-6332P16-H4 User’s manual (Short) ver.1.0

10

Note: In order to ensure stability and protection against overload and unauthorized access, we

recommend separating the network monitoring of LANs used by users.

Before configuring the connection of the cameras in the recorder, we recommend using a PC to

configure the cameras according to the instructions of the camera.

2.6. Connecting external devices

 Connecting audio ports

Audio output signal normally are above 200mV 1kΩ. You can connect to it the audio amplifier with

the external speakers.

 Connecting USB devices

NVR has 1 x USB 2.0 port on front and one 1 x USB 2.0 and 1 x 3.0 USB port on back panel . They

could be used for connecting external Flash memory, mouse connection and other USB compatible

devices. To connect storage memory it is recommended to use port USB 3.0

 Connecting alarms ports

STARTING THE DEVICE

Alarm-in

Alarm out

RS485

GND

NVR-6332P16-H4 User’s manual (Short) ver.1.0

11

Example of connecting alarm output no. 1, follow the drawing below:

Example of sensor connection to alarm input 1.

STARTING THE DEVICE

NO COM

ALARM

Power

source

NO1 COM1

ALARM

Power

source

NVR-6332P16-H4 User’s manual (Short) ver.1.0

12

NVR OPERATING

3. NVR OPERATING

3.1. Front panel description

1. LED LEDs for monitoring NVR activity.

- REC - monitors recording activity

- NET - monitors networking activity

- PWR - activities when power is on

2. USB USB 2.0 port for external Flash memory and mouse connection.

.

3.2. Controlling via USB mouse

It is possible to control NVR via an USB mouse connected to the USB port. Double-click on any

camera in split screen display mode switches the display to full-screen mode. Subsequent double-click

returns to previous display mode. Move cursor to the top or click the right key of mouse to bring up

MAIN MENU and select START icon.

Certain positions allow to select them via mouse scroll. Depending on NVR operating mode, pressing

RMB displays a corresponding function menu.

3.3. System operations

To start NVR plug power cable and switch on power. The power led turns on. After booting, the video

output default is multi-window output mode.

Note:

If the currently selected NVR menu language is not as expected, to change it, please follow the

procedure described in chapter 4.3 of this manual.

1

2

NVR-6332P16-H4 User’s manual (Short) ver.1.0

13

To unlock the DVR menu, click the button at the bottom left of the screen.

After clicking on button click-on “LOGIN”

Then login in entering password in PASSWORD field (default password for user root is “pass”)

and then click-in login button

NVR OPERATING

NVR-6332P16-H4 User’s manual (Short) ver.1.0

14

3.4. Startup configuration

Prior to using NVR for the first time, initial setup is strongly advised. Before you connect the IP

cameras to the NVR, please set up network and stream parameters of IP cameras in the right way.

Note:

For suggested values for IP camera setting please refer to the “Cameras Capability Table” available

on the www.novuscctv.com website. If you set wrong values some problems may appear: the NVR

cannot search the IP camera, the stream cannot be connected, the image is not fluent, the image quality

is bad and so on.

In case of first NVR start WIZARD SETUP menu window will occur (if function wasn’t disabled

earlier). To configure NVR please follow procedure like below, after finishing all the steps you’ll be

ready to work:

Provide username and password and click on NEXT button so start wizard.

NVR OPERATING

NVR-6332P16-H4 User’s manual (Short) ver.1.0

15

I. NETWORK SETTINGS : This menu allows to set up networking. Default IP configuration is

192.168.1.100 netmask 255.255.255.0. It is possible to configure IP address for switch in INTERNAL

ETHERNET PORT SECTION. Please note that IP subnet for the ETHERNET PORT 1 and

INTERNAL ETHERNET PORT were different. In cases where it is necessary to NVRa connection to

the Internet (for remote access, email sending, etc.), configure the following parameters: Gateway,

Primary and Secondary DNS. You can also enable DHCP mode which allows you to download an IP

address from a DHCP server (required if running a DHCP server). It is possible to change the default

HTTP port designed to display Web panel of the device and RTSP ports and port server data. After

changing parameter pres NEXT button.

NVR OPERATING

Internal PoE Ports

IP address settings

Internal PoE Ports

IP address settings

NVR-6332P16-H4 User’s manual (Short) ver.1.0

16

II. QR CODES : This menu allows you to scan a QRcode in the Supelive plus application or enter a

device code to autonat.com site. The service allows you to connect to a device connected to the Internet

network behind a router equipped with NAT.

NOTE: AAT Holding S.A is not responsible for the operation of the service autonat.com which is

provided by third parties.

III. Add Camera: Allows you to configure the camera and add them to the recorder. Upper window

displays a discovered camera by the NVR. To change the addressable cameras, click on the icon in

the column EDIT (This works with cameras NOVUS IP 3000 series).

NVR OPERATING

NVR-6332P16-H4 User’s manual (Short) ver.1.0

17

Enter the address in the IP ADDRESS and set the masks in the SUBNET MASK then press the OK

button to save the settings.

Press the button to add a camera to the system.

Added camera will be displayed on the bottom of the menu list. To edit the connection settings of the

camera, press the EDIT column.

If you are having problems connecting to the camera, you must enter the correct user name in the

USER NAME and password in the PASSWORD field and then press the OK button to save the

settings. If the NVR connected to the camera in STATUS filed will be displayed “Connected”. To

remove a camera from the list, press the in DELETE column.

NVR OPERATING

NVR-6332P16-H4 User’s manual (Short) ver.1.0

18

IV.DISK SETTINGS : In this tab information about the hard disk detected by the DVR is displayed.

Before starting work, you need to format the hard disk by selecting it in the list of drives and then

pressing FORMAT.

Formatting may take a few moments. After properly formatted STATUS field should have a value of

„RW” (Read/Write).

V. Record Settings :

You can set one of the modes:

- MANUAL RECORD SETTINGS - You can set the recording time from the moment you select the

manual recording from 1 minute to 1 hour or manually off recording.

NVR OPERATING

NVR-6332P16-H4 User’s manual (Short) ver.1.0

19

 AUTO - set all the cameras on one of the following modes :

- MOTION RECORD - starts recording after receiving motion detection information from the camera.

- SENSOR RECORD - starts recording after alarm generated on alarm input

- MOTION RECORD + SENSOR RECORD - starts recording after motion detecion alarm and after

alarm from alarm inputs

- ALWAYS(24x) RECORD + MOTION RECORD - continuous recording and recording after

receiving motion detection information from the camera.

- ALWAYS(24x) RECORD + SENSOR RECORD - continuous recording and recording alarm

generated on alarm input

- ALWAYS(24x) RECORD + MOTION RECORD + SENSOR RECORD - continuous recording and

recording alarm generated on alarm input and after receiving motion detection information from the

camera.

NVR OPERATING

NVR-6332P16-H4 User’s manual (Short) ver.1.0

20

4. NVR MENU

4.1. Live monitoring

NOVUS network video recorders features a multilingual OSD menu allowing to adjust the settings of

the device. Available languages are: English, Polish, and others

As soon as the NVR completes its initialization process, it will enter the real-time monitoring image.

Displaying all cameras simultaneously is the default mode. On the bottom of screen STATUS BAR is

displayed.

To start access to the NVR click on the button to launch the start menu.

After clicking log on to the system (the default password for the root user is a "pass").

.

STATUS BAR description:

NVR MENU

Item Icon Description

Search Launches search for recordings

Playback

Starts playback menu

Backup Starts backup menu

MENU BAR

VIDEO WINDOW

VIEW MENU

START MENU

Strona jest ładowana ...

Novus NVR-6332P16-H4/F Instrukcja obsługi

Ten podręcznik jest również odpowiedni dla

Novus NVR-6332P16-H4/F Instrukcja obsługi

w innych językach

Powiązane dokumenty

Inne dokumenty