Parkside PWS 125 B2 Translation Of Original Operation Manual

ANGLE GRINDER PWS 125 B2

WINKELSCHLEIFER

Originalbetriebsanleitung

ANGLE GRINDER

Translation of original operation manual

SZLIFIERKA KĄTOWA

Tłumaczenie oryginalnej instrukcji obsługi

ÚHLOVÁ BRUSKA

Překlad originálního provozního návodu

UHLOVÁ BRÚSKA

Preklad originá lneho návodu na obsluhu

KOTNI BRUSILNIK

Prevod originalnega navodila za uporabo

SAROKCSISZOLÓ

Az originál használati utasítás fordítása

IAN 100132

100132_par_Akku-Winkelschleifer_cover_PL_HU_SI_CZ_SK.indd 2 01.07.14 11:27

GB Translation of original operation manual Page

P L Tłumaczenie oryginalnej instrukcji obsługi Strona

HU Az originál használati utasítás fordítása Oldal

SI Prevod originalnega navodila za uporabo Stran

CZ Překlad originálního provozního návodu Strana

SK Preklad originálneho návodu na obsluhu Strana

DE / AT / CH Originalbetriebsanleitung Seite

Before reading, unfold the page containing the illustrations and familiarise yourself with all functions

of the device.

Przed przeczytaniem proszę rozłożyć stronę z ilustracjami, a następnie proszę zapoznać się z

wszystkimi funkcjami urządzenia.

Olvasás előtt kattintson az ábrát tartalmazó oldalra és végezetül ismerje meg a készülék mindegyik

funkcióját.

Pred branjem odprite stran s slikami in se nato seznanite z vsemi funkcijami naprave.

Před čtením si otevřete stranu s obrázky a potom se seznamte se všemi funkcemi přístroje.

Pred čítaním si odklopte stranu s obrázkami a potom sa oboznámte so všetkými funkciami prístroja.

Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend

mit allen Funktionen des Gerätes vertraut.

100132_par_Akku-Winkelschleifer_cover_PL_HU_SI_CZ_SK.indd 3 01.07.14 11:27

4

21

41

59

77

95

113

1 2 3 4

8

9

7

5

6

10

11

12

13

16

15

14

4

GB

Content

Introduction .................................4

Intended purpose .........................4

General description ......................5

Extent of the delivery ........................5

Description of function ......................5

Overview ........................................5

Technical Data ..............................5

Notes on safety............................6

Symbols and icons ...........................6

General Safety Directions for Power

Tools ...............................................7

Safety instructions for all applications .9

Additional safety instructions ...........10

Residual risks .................................11

Kickback .......................................12

Additional safety instructions for

sanding ........................................12

Additional safety instructions for

working with wire brushes ...............12

Special safety instructions for grinding

and cutting ....................................13

Other special safety instructions for

cutting grinding .............................13

Practical tips ..................................14

Assembly ...................................14

Mount handgrip .............................14

Assemble/set protective hood ..........14

Installing/changing disc .................14

Operation ..................................15

Turning on and off ..........................16

Cleaning and servicing ...........16

Cleaning .......................................16

Storage ......................................16

Waste disposal and

environmental protection ...........17

Troubleshooting ......................... 17

Replacement parts/Accessories ..18

Guarantee ................................. 19

Repair-Service ............................ 20

Service-Center ............................20

Importer .................................... 20

Translation of the original

EC declaration of conformity ....133

Introduction

Congratulations on the purchase of your

new device. With it, you have chosen a

high quality product.

During production, this equipment has

been checked for quality and subjected

to a nal inspection. The functionality of

your equipment is therefore guaranteed. It

cannot be ruled out that residual quantities

of water or lubricants will remain on or in

the equipment/hose lines in isolated cases.

This is not a fault or defect and it repre-

sents no cause for concern.

The operating instructions constitute part of

this product. They contain important infor-

mation on safety, use and disposal.

Before using the product, familiarise your-

self with all of the operating and safety

instructions. Use the product only as de-

scribed and for the applications specied.

Keep this manual safely and in the event

that the product is passed on, hand over

all documents to the third party.

Intended purpose

The angle grinder is a tool for cutting,

scrubbing and brushing metal without

using water.

The device is not intended for any other

types of applications (e.g. grinding with

unsuitable grinding tools, grinding with a

coolant solution, grinding or cutting hazar-

dous materials such as asbestos).

The device is intended to be used by do-it-

yourselfers. It was not designed for heavy

commercial use.

The tool is to be used by adults. Children

under the age of 16 may not use the tool

except under supervision.

5

GB

The manufacturer is not liable for damages

caused by an improper use or incorrect

operation of this device.

General description

See the front fold-out page for

illustrations.

Extent of the delivery

Carefully unpack the appliance and check

that it is complete:

- Device

- Handgrip

- Protective hood

- Chuck key

- Cutting disc

- Instruction Manual

Description of function

The angle grinder is made for cutting,

scrubbing or brushing metal. There is a

special disc for each of the separate ap-

plications. Please refer to the information

from the disc manufacturer.

Please refer to the descriptions below for

information about the operating devices.

Overview

1 Handgrip

2 Threads for handgrip

3 Speed regulator

4 Switch block

5 On/off switch

6 Threads for handgrip

7 Spindle stop button

8 Power plug

9 Chuck key

10 Cutting disc

11 Protective hood

12 Mounting ange

13 Clamping nut

14 Mounting spindle

15 Adjustment nut

16 Tightening lever

Technical data

Angle Grinder PWS 125 B2:

Rated input voltage

............................... 230-240 V~, 50 Hz

Power input ............................ 1200 W

Idling speed (n) ............3000-12000 min

-1

Safety class ..................................... II

Protection category......................... IP 20

Sound pressure level

(L

pA

) ...............92,1 dB(A); K

pA

= 3 dB(A)

Sound power level (L

wA

)

measured .....103,1 dB(A); K

wA

= 3 dB(A)

guaranteed .....106 dB(A); K

wA

= 3 dB(A)

Vibration (a

h

)

Main handgrip 11,237 m/s

2

K= 1,5 m/s

2

Supplemental handgrip

......................... 8,146 m/s

2

K= 1,5 m/s

2

Cutting disc:

Idling speed n

0

................................... max.12200 min

-1

Disc speed ....................... max. 80 m/s*

Outer diameter ................... Ø 125 mm

Bore hole ........................ Ø 22,23 mm

Thickness ...................................3 mm

*

The grinding disc must keep a rotational

speed of 80 m/s.

Levels of noise and vibration were determi-

ned according to the norms and regulations

in the declaration of conformity.

Technical and visual changes may be made

as part of ongoing development without

announcement. All dimensions, instructions

and specications are therefore without

guarantee. Legal claims on the basis of the

6

GB

operating manual may therefore not be

asserted.

The vibration emission value has been mea-

sured according to a standardised testing

method and may be used for comparison

with another electric tool.

The indicated vibration emission value may

also be used for an introductory assessment

of the exposure.

Warning:

The vibration emission value whilst

actually using the electrical tool may

vary from the given values indepen-

dently of the type and way in which

the electric tool is used.

Safety measures for the protection

of the operator are to be determi-

ned that are based on an estimate

of the actual exposure under the

real operating conditions (for this,

all parts of the operating cycle are

to be taken into account, for examp-

le, times in which the electric tool is

turned off, and those during which

it is turned on but running without a

load).

Notes on safety

Caution! When using power tools,

observe the following basic safety

measures for the prevention of elec-

tric shocks and the risk of injury and

re.

Please read all these instructions be-

fore using this electric tool and please

keep the safety instructions.

Symbols and icons

Symbols on the device:

Warning!

Risk of injury from the rotating tool!

Keep hands away

Warning! Electric shock hazard.

Always unplug the device before

working on it

Read the manual!

Wear ear protection

Wear eye protection

Wear breathing protection

Risk of cuts!

Wear cut-resistant gloves

Safety class II

Electrical machines do not belong

with domestic waste

Other symbols on the

cutting disc:

Do not use for side grinding

Do not use for wet grinding

Do not use defective discs

Suitable for metal

Wear safety shoes

7

GB

• Keep children and bystanders

away while operating a power

tool. Distractions can cause you to lose

control.

Electrical safety :

CAUTION! The following states how

to avoid accidents and injuries due to

electric shock:

• Power tool plugs must match the

outlet. Never modify the plug in

any way. Do not use any adapter

plugs with earthed (grounded)

power tools. Unmodied plugs and

matching outlets will reduce risk of electric

shock

• Avoid body contact with earthed

or grounded surfaces, such as

pipes, radiators, ranges and ref-

rigerators. There is an increased risk of

electric shock if your body is earthed or

grounded.

• Do not expose power tools to rain

or wet conditions. Water entering a

power tool will increase the risk of electric

shock.

• Do not abuse the cord. Never use

the cord for carrying, pulling or

unplugging the power tool. Keep

cord away from heat, oil, sharp

edges or moving parts. Damaged or

entangled cords increase the risk of elec-

tric shock.

• When operating a power tool

outdoors, use an extension cord

suitable for outdoor use. Use of a

cord suitable for outdoor use reduces the

risk of electric shock.

Symbols used in the instructions:

Hazard symbols with in-

formation on prevention of

personal injury and property

damage.

Precaution symbol (explanation of

precaution instead of exclamation

mark) with information on preventi-

on of harm / damage.

Notice symbol with information on

how to handle the device properly.

General Safety Directions for

Power Tools

WARNING! READ ALL SAFETY

DIRECTIONS AND INSTRUC-

TIONS. Omissions in the compliance

with safety directions and instructions

can cause electrical shock, re and/

or severe injuries.

Retain all safety directions and inst-

ructions for future use.

The term „power tool“ in the warnings refers

to your mains-operated (corded) power tool

or battery-operated (cordless) power tool).

Work area safety :

• Keep work area clean and well

lit. Cluttered or dark areas invite acci-

dents.

• Do not operate power tools in

explosive atmospheres, such as

in the presence of ammable

Iiquids, gases or dust. Power tools

create sparks which may ignite the dust or

fumes.

8

GB

• If operating a power tool in a

damp location is unavoidable, use

a residual current device (RCD)

protected supply. Use of an RCD

reduces the risk of electric shock. Use a

circuit breaker with a current limit of

30 mA or less.

Personal safety:

CAUTION! The following states how

to avoid accidents and injuries:

• Stay alert, watch what you are

doing and use common sense

when operating a power tool. Do

not use a power tool while you

are tired or under the inuence of

drugs, alcohol or medication. A mo-

ment of inattention white operating power

tools may result in serious personal injury.

• Use personal protective equip-

ment. Always wear eye protec-

tion. Protective equipment such as dust

mask, non-skid safety shoes, hard hat, or

hearing protection used for appropriate

conditions will reduce personal injuries.

• Prevent unintentional starting.

Ensure the switch is in the off-

position before connecting to po-

wer source and/or battery pack,

picking up or carrying the tool.

Carrying power tools with your nger on

the switch or energising power tools that

have the switch on invites accidents.

• Remove any adjusting key or

wrench before turning the power

tool on. A wrench or a key left attached

to a rotating part of the power tool may

result in personal injury.

• Do not overreach. Keep proper

footing and balance at all times.

This enables better control of the power

tool in unexpected situations.

• Dress properly. Do not wear loose

clothing or jewellery. Keep your

hair, clothing and gloves away

from moving parts. Loose clothes,

jewellery or long hair can be caught in

moving parts.

• If devices are provided for the

connection of dust extraction and

collection facilities, ensure these

are connected and properly used.

Use of dust collection can reduce dust-

related hazards.

Power tool use and care :

• Do not force the power tool. Use

the correct power tool for your

application. The correct power tool will

do the job better and safer at the rate for

which it was designed.

• Do not use the power tool if the

switch does not turn it on and off.

Any power tool that cannot be controlled

with the switch is dangerous and must be

repaired.

• Disconnect the plug from the po-

wer source and/or the battery

pack from the power tool before

making any adjust -ments, chan-

ging accessories, or storing power

tools. Such preventive safety measures

reduce the risk of starting the power tool

accidentaIly.

• Store idle power tools out of the

reach of children and do not al-

low persons unfamiliar with the

power tool or these instructions to

operate the power tool. Power tools

are dangerous in the hands of untrained

users.

• Maintain power tools. Check for

misalignment or binding of mo-

ving parts, breakage of parts

and any other condition that may

9

GB

affect the power tool’s operation.

If damaged, have the power tool

repaired before use. Many accidents

are caused by poorly maintained power

tools.

• Keep cutting tools sharp and

clean. Properly maintained cutting tools

with sharp cutting edges are less Iikely to

bind and are easier to control.

• Use the power tool, accessories

and tool bits etc. in accordance

with these instructions, taking into

account the working conditions

and the work to be performed.

Use of the power tool for operations diffe-

rent from those intended could result in a

hazardous situation.

Service:

• Have your power tool serviced by

a qualied repair person using

only identical replacement parts.

This will ensure that the safety of the pow-

er tool is maintained.

Safety instructions for all ap-

plications

Common safety instructions for

grinding, sanding, working with

wire brushes and cutting grinders:

• This electric tool is to be used as

a grinder, sander, wire brush

and cutting grinder. Follow all

safety instructions, directives,

illustrations and facts which you

receive with the device. If you do

not follow these instructions, an elec-

trical shock, re and/or serious injury

may occur.

• This electric tool is not suitable

for polishing. Using the electric tool

in ways for which it is not intended may

cause hazards and injuries.

• Do not use any accessories that

are not specically intended and

recommended for this electric

tool by the manufacturer. Simply

because an accessory can be attached

to your electric tool does not guarantee

safe operation.

• The allowable rotation speed of

the attachment tools must be at

least as high as the highest rota-

tion speed indicated on the elec-

tric tool. Accessories that run faster

than the allowable speed can break and

y apart.

• The outside diameter and thick-

ness of the attachment tool must

correspond to the dimensions

indicated for your electric tool. At-

tachment tools which are wrongly dimen-

sioned cannot be sufciently shielded or

controlled.

• Attachment tools with threaded

attachment must t the threading

of the grinding spindle exact-

ly. For attachment tools which

are mounted through a ange,

the diameter of the hole in the

attachment tool must t the

mounting diameter of the ange.

Attachment tools which cannot be pre-

cisely attached to the electric tool turn

unevenly, vibrate very strongly and can

ultimately lead to a loss of control.

• Never use damaged attach-

ment tools. Check attachment

tools such as grinding discs for

chipping or cracks, grinding pla-

tes for cracks, wear or strong

abrasion and wire brushes for

loose or broken wires before

using them. If the electric tool

or the attachment tool falls off,

10

GB

check whether it is damaged or,

use an undamaged attachment

tool. If you have checked the

attachment tool and attached it,

keep yourself and any nearby

persons beyond the level of the

rotating attachment tool and al-

low the device to run for 1 min.

at the highest rotational speed.

Damaged tools usually break during this

test period.

• Wear personal safety equip-

ment. Depending on the appli-

cation, use full face shields, eye

protection or safety goggles. In

so far as it is appropriate, wear

dust masks, ear protection,

gloves or special aprons which

keep small grinding and materi-

al particles away from you. Eyes

should be protected from the foreign

matter which can be caused to y du-

ring the various applications. Dust or

breathing masks should lter the dust

that is created during operation. If you

are exposed to loud noise for a long

time, you may suffer hearing loss.

• Ensure that other people are at

a safe distance to your working

area. Anyone who enters the

working area should wear per-

sonal protective equipment. Bro-

ken bits from the piece being worked or

broken attachment tools can y away

and cause injuries even beyond the di-

rect working area.

• Hold the electric tool only by

the insulated gripping surfaces

when performing work in which

the cutting tool may come into

contact with hidden wiring or its

own cord. Contact with a live wire

can also cause a charge in metal parts

of the device and result in an electric

shock.

• Keep the cord away from the ro-

tating attachment tool. If you lose

control of the device, the power cord can

become separated or caught and your

hand or arm may be pulled into the rota-

ting attachment tool.

• Never put the electric tool down

before the attachment tool has

come to a full stop. The rotating at-

tachment tool can come into contact with

the surface upon which it is set, whereby

you could lose control of the electric tool.

• Never allow the electric tool to

run whilst you are carrying it.

Your clothing may accidentally come into

contact with the rotating attachment tool

and get caught and the attachment tool

could drill into your body.

• Clean the ventilation slots of your

electric tool routinely. The motor air

pulls dust into the housing and, should

too much metallic dust collect, could

cause electrical hazards.

• Never use the electric tool near

ammable material. Sparks could

ignite this material.

• Do not use attachment tools

which require liquid coolant. Using

water or another liquid coolant could

lead to electrical shock.

Additional safety instructions

• Connect the appliance only to a power

socket with a residual current circuit

breaker of rated residual current no

more than 30 mA.

• Keep power cords and extension cords

away from the disc. If they are damaged

or cut through, immediately pull the plug

11

GB

from the outlet. Do not touch the cable

before it has been disconnected from

the power supply.

Risk of electric shock!

• The replacement of the plug or the con-

nection line must always be executed

by the manufacturer of the electric tool

or his/her customer service in order to

avoid any hazards.

• Only use grinding discs where the in-

dicated rotational speed is at least as

high as what has been specied on the

name plate of the device.

• Carry out a visual inspection of the

grinding disc before use. Do not use

any damaged or deformed grinding

discs. Replace any damaged or worn

grinding discs.

• Make sure that the sparks produced by

grinding do not present a danger, e.g.

reach people or ignite ammable subs-

tances.

• Always wear safety goggles, safety

gloves, respiratory protection and ear

protection when grinding, brushing and

cutting.

• Never keep the ngers between the

grinding disc and spark protection or in

close proximity to the protective hoods.

There is a risk of crushing.

• The rotating parts of the device cannot

be covered due to functional reasons.

Therefore, proceed cautiously and hold

the workpiece rmly in order to avoid

slipping which could cause your hands

to come into contact with the grinding

disc.

• The workpiece gets hot during grin-

ding. Do not touch the machined area,

allow it to cool down. There is a risk of

burning. Do not use coolants or the like.

• If you are tired or have consumed al-

cohol or tablets, do not work with the

device. Always have a break on time.

• Switch the device off and remove the

mains plug

- to loosen a blocked insertion tool,

- if the connection line is damaged or

entangled,

- in case of unusual sounds.

RESIDUAL RISKS

Even if properly operating and handling

this electric tool, some residual risks will

remain. Due to its construction and build,

this electric tool may present the following

hazards:

a) Cuts

b) Ear damage if working without ear pro-

tection.

c) Damage to your health caused by swin-

ging your hands and arms when opera-

ting the appliance for longer periods of

time or if the unit is not held or maintai-

ned properly.

d) Health injuries which result from swin-

ging hand and arm, in the event that

the device is used over a longer period

of time or is not used and maintained

properly.

Warning! During operation, this

electric tool generates an electro-

magnetic eld which, under certain

circumstances, may impair the

functionality of active or passive

medical implants. To reduce the risk

of serious or lethal injuries, we re-

commend that persons with medical

implants consult their doctor and the

manufacturer of their medical im-

plant before operating the machine.

12

GB

Kickback

Kickback is the sudden reaction from a

chopping or blocked grinder attachment

such as a grinding disc, grinding plate,

wire brush etc. Chopping or blocking

leads to sudden stopping of the rotating

attachment. This causes an uncontrolled

electric tool to accelerate in a direction

counter to the rotational direction of the

attachment tool. If, for example, a grinding

disc cuts into the workpiece or blocks it,

the edge of the grinding disc that digs into

the workpiece can get caught and, through

that, break off the grinding disc or cause

a kickback. The grinding disc then moves

towards or away from the operator, depen-

ding on the direction of rotation of the disc

at the blocked spot. Here, the grinding

discs can also break. A kickback is caused

by wrongly or incorrectly operating the

electric tool. It can be avoided by suitable

cautionary measures, such as described

below.

a) Hold the electric tool very

rmly and bring your body and your

arm into a position in which you can

resist the kickback force. Always use

the supplemental handle if available to

give you the best control over kickback

force or reaction time during accele-

ration. The operator can master the

kickback and reaction force through

suitable precautions.

b) Never bring your hands near a rotating

attachment tool. The attachment tool

can run over your hand in the kickback.

c) Keep your body away from the area

in which the electric tool would move

during a kickback. The kickback drives

the electric tool in the counter-direction

to the rotation of the grinding disc at

the blocked spot.

d) Work particularly cautiously in corner

areas or where there are sharp cor-

ners etc. Prevent the attachment tools

from recoiling from the workpiece and

jamming. The rotating attachment tool

tends to jam when near corners, sharp

edges or when it recoils from such. This

causes a loss of control or kickback.

e) Do not use chain or toothed saw bla-

des. Such attachment tools frequently

cause a kickback or loss of control over

the electric tool.

Additional safety instructions

for sanding

Special safety instructions for

sanding:

• Do not use overly large sand-

paper sheets; follow the

manufacturer‘s information for

sandpaper sizes. Sandpaper sheets

which extend beyond the sanding plate

can cause injuries and can block, tear

the sandpaper, or cause kickback.

Additional safety instructions

for working with wire brushes

Special safety instructions for

working with wire brushes:

• Be aware that the wire brushes

also lose wire pieces during typi-

cal use. Do not overload the wi-

res by pressing down too hard.

Flying wire pieces can very easily penet-

rate thin clothing and/or your skin.

• If a protective hood is recom-

mended, do not allow the wire

brushes and the protective hood

to touch each other. The diameter of

plate and cup brushes can enlarge if too

13

GB

much pressure and centrifugal force is

exerted.

Special safety instructions for

grinding and cutting

a) Use only grinders which have been

approved for your electric tool and the

protective hood intended for these grin-

ders. Grinders which are not intended

for the electric tool may not be sufci-

ently shielded and are unsafe.

b) The protective hood must be securely

attached to the electric tool and adjus-

ted so that the greatest level of safety

is reached, i.e., the smallest possible

amount of the grinder is exposed to the

operator. The protective hood should

protect the operator from broken bits

and accidental contact with the grinder.

c) Grinders may only be used for the

recommended attachment options. For

example: Never grind with the side

surface of a cutting disc. Cutting discs

are for cutting material using the edge

of the disc. Pushing sideways on these

grinders can break them.

d) Always use undamaged clamping an-

ges of the correct size and shape for

the grinding disc you selected. Suitable

anges support the grinding disc and

thus reduce the danger of the grinding

disc breaking. Flanges for cutting discs

can be distinguished from anges for

other grinding discs.

e) Do not use worn grinding discs for

larger electric tools. Grinding discs for

larger electric tools are not set up for

the higher rotation speeds of smaller

electric tools and can break.

Other special safety instructions

for cutting grinding

a) Avoid blocking the cutting disc or pres-

sing down too hard. Do not make any

excessively deep cuts. Overloading the

cutting disc increases wear and its ten-

dency to tilt or block and, with that, to

kickback or break the grinder.

b) Avoid the area in front of and behind

the rotating cutting disc. When you

move the cutting disc by itself in the

workpiece, in the event that the electric

tool kicks back with the rotating disc, it

can spin directly towards you.

c) If the cutting disc jams, or you interrupt

your work, switch the device off and

hold it until the disc has come to a full

stop. Never try to pull the cutting disc

out of the cut while it is still running,

because it can kick back. Identify and

correct the cause of the jamming.

d) Do not switch the electric tool on again

as long as it is in the workpiece. Allow

the cutting disc to rst reach its full

rotational speed before you carefully

resume with the cutting. Otherwise, the

disc may catch, spring away from the

workpiece or cause a kickback.

e) Support plates or workpieces to reduce

the risk of kickback from a jammed cut-

ting disc. Large workpieces may bend

under their own weight. The workpiece

must be supported on both sides of the

disc, near the cutting disc as well as

also at the edge.

f) Be particularly careful for pocket cuts in

existing walls or other areas where you

cannot see what is there. The cutting

disc may cause a kickback when it cuts

into gas or water lines, electrical lines

or other hidden objects.

14

GB

Practical tips

Scrubbing wheels:

Never use a cutting wheel for

scrubbing !

Exert only moderate pressure on the work-

piece. Move the device evenly back and

forth.

A working angle of 30° to 40° achieves

the best results for scrub grinding.

Cutting disc:

Never use a scrubbing wheel

for cutting !

Only certied, bre-reinforced cutting or

grinding discs may be used.

In general, work with small scrubs. Exert

only moderate pressure on the workpiece.

Always work in the counter-direction. This

ensures that the device is not pushed out of

the cut through lack of control.

Assembly

Caution! Risk of injury!

- Ensure that you have sufcient

space in which to work, and that

you do not endanger other peo-

ple.

- All hoods and protective devices

must be assembled properly be-

fore commissioning.

- Disconnect the mains plug be-

fore changing the setting on the

device

Mount handgrip

The device must only be

operated with the handgrip

mounted.

Screw the handgrip (1), depending on the

type of work, to the left, right or above the

device using the threading for the hand-

grip (2/6)..

Assemble/set protective

hood

The device must only be

operated with the protective

hood mounted.

1. Open the tightening lever

(

C

16)

2. Place the protective hood (

11) on the positioning holes.

3. Turn the protective hood (

11) into the working position.

The closed side of the protective

hood must always face the ope-

rator.

4. Close the tightening lever

(

C

16) again. The protective

hood should not be able to be

turned any more.

If needed, the tension on the adjustment

nut (

C

15) can be set. Use the chuck key

(

9) for this.

Installing/changing disc

1. Press the spindle stop button

(

7).

2. Release the clamping nut

(

B

13) with the chuck key

(

9).

15

GB

3. Set the desired disc onto the

mounting ange (

B

12). label on

the disc should always face the

device.

4. Set the clamping nut (

B

13) on

the mounting spindlel (

B

14)

again. The at side of the clam-

ping nut must face the attach-

ment tool.

5. Press the spindle stop button

(

7) and pull the clamping

nut (

B

13) tight again using the

chuck key (

9).

Operation

Caution! Risk of injury!

- Always remove the mains plug

before working on the tool.

- Only use grinding discs and

accessories recommended by the

manufacturer. Using other attach-

ment tools and other accessories

can represent a risk of injury for

you.

- Only use grinding tools which

bear information about the

manufacturer, type of binding,

dimension and permitted number

of revolutions.

- Only use grinding discs where

the printed rotational speed is at

least as high as what has been

specied on the name plate of

the device.

- Do not use any broken, cracked,

or otherwise damaged grinding

discs.

- Never operate the device wit-

hout protective equipment.

Keep your hands away from

the disc when the device is in

operation. Risk of injury.

Information on replace-

ment:

• Never operate the device without

protective equipment.

• Ensure that the rotation speed

stated on the grinding disc (

10) ) is the same or higher than

the nominal rotation speed of the

device.

• Ensure that the grinding disc

dimensions match those of the

device.

• Only use awless grinding discs

(ringing test: when you strike the

grinding disc with a plastic ham-

mer, it results in a clear sound).

• Never re-drill a locating hole

which is too small to make it lar-

ger.

• Never use separate bushings or

adapters in order to make grin-

ding discs with a hole that is too

large t the device.

• Do not use any saw blades.

• To clamp the grinding tools

only use the clamping ange

provided. The pads between

the clamping ange and the

grinding tools must be made of

elastic materials e.g., rubber,

soft cardboard etc.

• Always reassemble the device

completely after replacing the

grinding disc.

Switch the device off and remove

the mains plug. Allow the device to

cool down.

Wear protective gloves when chan-

ging the grinding discs in order to

avoid cutting damages.

16

GB

The grinding disc nut must not be

screwed too tightly in order to avo-

id breaking the disc and nut.

Turning on and off

Make sure that the power supply

voltage matches the voltage rating

indicated on the device‘s type pla-

te.

Connect the machine to the power

supply.

1. Press the on switch (4) to start the de-

vice. Press the on/off switch (5).

2. To turn it off, release the on-off button.

The device turns off.

After switching on the device, wait until the

device has reached its max. speed. Only

then should you start with the work.

The disc still runs even after

the device has been switched

off. Risk of injury.

Trial run:

Always carry out a trial run before carry-

ing out your rst grinding procedure and

after every disc replacement. Switch the

device off immediately if the grinding disc

is not rotating smoothly, if considerable

vibration occurs or if you hear abnormal

noises.

Cleaning and servicing

Pull the mains plug before any ad-

justments, maintenance or repair.

Have any work on the device

that is not described in this in-

struction guide performed by

a professional. Only use ori-

ginal parts. Allow the device

to cool off before any mainte-

nance or cleaning is underta-

ken. There is a risk of burning!

Always check the device before using it for

obvious deciencies such as loose, worn

or damaged parts, correct the positioning

of screws or other parts. Examine the

grinding disc in particular. Exchange the

damaged parts.

Cleaning

Do not use any cleaning agent or

solvent. Chemical substances can

etch the plastic parts of the device.

Never clean the device under run-

ning water.

• Thoroughly clean the device after every

use.

• Clean the ventilation openings and the

surface of the device with a soft brush

or cloth.

Storage

• Store the appliance in a dry place well

out of reach of children.

• Grinding discs must be dry and stored

upright and should never be stacked.

17

GB

Waste disposal

and environmental

protection

Be environmentally friendly. Return the

tool, accessories and packaging to a recy-

cling centre when you have nished with

them.

Electrical machines do not belong

with domestic waste.

• Hand over the device at an utilization

location. The plastic and metal parts

employed can be separated out and

thus recycled use can be implemented.

Ask our Service-Center for details.

• Defective units returned to us will be dis-

posed of for free.

Troubleshooting

Always unplug the shredder before working on it.

Risk of electric shock!

Problems Possible Cause Error correction

Device doesn‘t start

Mains voltage missing

Main circuit breaker is tripped

Check the socket, mains cable,

line, mains plug, repairs to be

carried out by qualied electri-

cian if necessary, check main

circuit breaker.

On/off switch (

5) may be

defective

Repair by Customer Care

Engine faulty

Grinding tools do

not move although

the engine is run-

ning

Grinding disc nut is loose

Tighten grinding disc nut (see

„Changing the grinding disc“)

Workpiece, remaining workpie-

ces or remaining grinding tools

block drive

Remove blockages

Engine is slower

and stops

Device is overloaded through

workpiece

Reduce pressure on grinding tool

Workpiece unsuitable

Grinding disc does

not rotate smoothly,

abnormal noises

can be heard

Grinding disc nut is loose

Tighten grinding disc nut (see

„Changing the grinding disc“)

Grinding disc is defective Change grinding disc

18

GB

Replacement parts/Accessories

Spare parts and accessories can be obtained at

www.grizzly-service.eu

If you do not have internet access, please contact the Service Centre via telephone

(see “Service-Center” page 20). Please have the order number mentioned below ready.

Cutting disc Cup brush, waved wire

Item.-No.:91103210

Flap disc Cup brush, braided wire

Item.-No.:91103211

Mounting plate for sandpaper Disc brush, braided wire

Item.-No.:91103212

19

GB

Guarantee

Dear Customer,

This equipment is provided with a 3-year

guarantee from the date of purchase.

In case of defects, you have statutory rights

against the seller of the product. These

statutory rights are not restricted by our

guarantee presented below.

Terms of Guarantee

The term of the guarantee begins on the

date of purchase. Please retain the original

receipt. This document is required as proof

of purchase.

If a material or manufacturing defect

occurs within three years of the date of

purchase of this product, we will repair or

replace – at our choice – the product for

you free of charge. This guarantee requires

the defective equipment and proof of pur-

chase to be presented within the three-year

period with a brief written description of

what constitutes the defect and when it oc-

curred.

If the defect is covered by our guarantee,

you will receive either the repaired product

or a new product. No new guarantee pe-

riod begins on repair or replacement of the

product.

Guarantee Period and Statutory

Claims for Defects

The guarantee period is not extended by

the guarantee service. This also applies for

replaced or repaired parts. Any damages

and defects already present at the time of

purchase must be reported immediately af-

ter unpacking. Repairs arising after expiry

of the guarantee period are chargeable.

Guarantee Cover

The equipment has been carefully pro-

duced in accordance with strict quality

guidelines and conscientiously checked

prior to delivery.

The guarantee applies for all material and

manufacturing defects. This guarantee

does not extend to cover product parts that

are subject to normal wear and may there-

fore be considered as wearing parts (e.g.

lters or attachments) or to cover damage

to breakable parts (e.g. switches, batteries,

or parts made of glass).

This guarantee shall be invalid if the prod-

uct has been damaged, used incorrectly or

not maintained. Precise adherence to all of

the instructions specied in the operating

manual is required for proper use of the

product. Intended uses and actions against

which the operating manual advises or

warns must be categorically avoided.

The product is designed only for private

and not commercial use. The guarantee

will be invalidated in case of misuse or

improper handling, use of force, or inter-

ventions not undertaken by our authorised

service branch.

Processing in Case of Guarantee

To ensure efcient handling of your query,

please follow the directions below:

• Please have the receipt and item num-

ber (IAN 100132) ready as proof of

purchase for all enquiries.

• Please nd the item number on the rat-

ing plate.

• Should functional errors or other de-

fects occur, please initially contact the

service department specied below by

telephone or by e-mail. You will then

receive further information on the pro-

cessing of your complaint.

20

GB

• After consultation with our customer

service, a product recorded as defective

can be sent postage paid to the service

address communicated to you, with the

proof of purchase (receipt) and speci-

cation of what constitutes the defect

and when it occurred. In order to avoid

acceptance problems and additional

costs, please be sure to use only the ad-

dress communicated to you. Ensure that

the consignment is not sent carriage

forward or by bulky goods, express or

other special freight. Please send the

equipment inc. all accessories supplied

at the time of purchase and ensure ad-

equate, safe transport packaging.

Repair Service

For a charge, repairs not covered by

the guarantee can be carried out by

our service branch, which will be happy to

issue a cost estimate for you.

We can handle only equipment that has

been sent with adequate packaging and

postage.

Attention: Please send your equipment to

our service branch in clean condition and

with an indication of the defect.

Equipment sent carriage forward or by

bulky goods, express or other special

freight will not be accepted.

We will dispose of your defective devices

free of charge when you send them to us.

Service-Center

Service Great Britain

Tel.: 0871 5000 720

(£ 0.10/Min.)

E-Mail: [email protected]

IAN 100132

Importer

Please note that the following address is

not a service address. Please initially con-

tact the service centre specied above.

Grizzly Tools GmbH & Co. KG

Am Gewerbepark 2

64823 Groß-Umstadt

Germany

www.grizzly-service.eu

GB

Strona jest ładowana ...

Parkside PWS 125 B2 Translation Of Original Operation Manual

Parkside PWS 125 B2 Translation Of Original Operation Manual

w innych językach

Powiązane dokumenty

Inne dokumenty