Parkside PWSA 18 A1 Translation Of The Original Instructions

CORDLESS ANGLE GRINDER PWSA 18 A1

AKKU-WINKELSCHLEIFER

Originalbetriebsanleitung

CORDLESS ANGLE GRINDER

Translation of the original instructions

A

KUMULATOROWA SZLIFIERKA KĄTOWA

Tłumaczenie oryginalnej instrukcji obsługi

A

KU ÚHLOVÁ BRUSKA

Překlad originálního provozního návodu

AKUMULÁTOROVÁ UHLOVÁ BRÚSKA

Preklad originá lneho návodu na obsluhu

A

KUMULATORSKI KOTNI BRUSILNIK

Prevod originalnega navodila za uporabo

AKKUS SAROKCSISZOLÓ

Az originál használati utasítás fordítása

IAN 104454

104454_par_Akku-Winkelschleifer_cover_PL_HU_SI_CZ_SK.indd 2 19.02.15 11:34

GB Translation of the original instructions Page

PL Tłumaczenie oryginalnej instrukcji obsługi Strona

HU Az originál használati utasítás fordítása Oldal

SI Prevod originalnega navodila za uporabo Stran

CZ Překlad originálního provozního návodu Strana

SK Preklad originálneho návodu na obsluhu Strana

DE / AT / CH Originalbetriebsanleitung Seite

Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of the

device.

Przed przeczytaniem proszę rozłożyć stronę z ilustracjami, a następnie proszę zapoznać się z wszystkimi

funkcjami urządzenia.

Olvasás előtt kattintson az ábrát tartalmazó oldalra és végezetül ismerje meg a készülék mindegyik

funkcióját.

Pred branjem odprite stran s slikami in se nato seznanite z vsemi funkcijami naprave.

Před čtením si otevřete stranu s obrázky a potom se seznamte se všemi funkcemi přístroje.

Pred čítaním si odklopte stranu s obrázkami a potom sa oboznámte so všetkými funkciami prístroja.

Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen

Funktionen des Gerätes vertraut.

104454_par_Akku-Winkelschleifer_cover_PL_HU_SI_CZ_SK.indd 3 19.02.15 11:34

4

27

51

75

97

119

141

21

20

1

2

3 4 8

9

7

5

6

10

1112

16 15 1417

18

19

15 17

13

4

GB

Content

Introduction .................................4

Intended purpose ......................... 4

General description ......................5

Extent of the delivery ........................5

Description of function ......................5

Overview ........................................5

Technical data ..............................5

Notes on safety............................6

Symbols and icons ...........................7

General Safety Directions for Power

Tools ..............................................8

Additional safety instructions ...........13

RESIDUAL RISKS ......................14

Charging the battery ..................17

Removing / inserting the battery ......17

Recharging the battery....................17

Used batteries ...............................18

Checking the battery charge level ....18

Practical tips ..............................18

Assembly ...................................18

Mount additional handgrip .............19

Assemble/set protective hood ..........19

Installing/changing disc .................19

Operation ..................................19

Turning on and off ..........................20

Cleaning and servicing ...............21

Cleaning .......................................21

Storage ......................................21

Disposal and protection of the envi-

ronment .....................................21

Replacement parts/Accessories ..22

Troubleshooting .........................23

Guarantee .................................24

Repair Service ............................25

Service-Center ............................25

Importer ....................................25

Translation of the original

EC declaration of conformity ....165

Introduction

Congratulations on the purchase of your

new device. With it, you have chosen a

high quality product.

During production, this equipment has

been checked for quality and subjected to

a nal inspection. The functionality of your

equipment is therefore guaranteed.

The operating instructions constitute

part of this product. They contain

important information on safety,

use and disposal. Before using the

product, familiarise yourself with

all of the operating and safety in-

structions. Use the product only as

described and for the applications

specied. Keep this manual safely

and in the event that the product

is passed on, hand over all docu-

ments to the third party.

Intended purpose

The angle grinder is a tool for cutting,

scrubbing and brushing metal, concrete or

tiles without using water.

The device is not intended for any other

types of applications (e.g. grinding with

unsuitable grinding tools, grinding with a

coolant solution, grinding or cutting hazar-

dous materials such as asbestos).

The device is intended to be used by do-it-

yourselfers. It was not designed for heavy

commercial use.

The tool is to be used by adults. Children

under the age of 16 may not use the tool

except under supervision.

The manufacturer is not liable for damages

caused by an improper use or incorrect

operation of this device.

5

GB

General description

See the front fold-out page for

illustrations.

Extent of the delivery

Carefully unpack the appliance and check

that it is complete. Dispose of the packag-

ing material correctly.

- Device

- Battery-charger

- Battery

- Additional handle

- Protective hood

- Chuck key

- Cutting disc

- Translation of the original instructions

for use

Description of function

The angle grinder is made for cutting,

scrubbing or brushing metal. There is a

special disc for each of the separate ap-

plications. Please refer to the information

from the disc manufacturer.

Please refer to the descriptions below for

information about the operating devices.

The battery included in the scope of deliv-

ery can also be used for the cordless recip-

rocating saw PSSA 18 A1 and the cordless

drill driver PDSSA 18 A1.

Overview

1 Chuck key with storage facility

(not visible)

2 Additional handle

3 Spindle stop button

4 Threads for additional handgrip

5 On/off switch

6 Handgrip

7 Activation button battery Indicator

8 Battery Indicator

9 Battery

10 Battery release button

(not visible)

11 Power plug of charger

12 Green LED

13 Red LED

14 Charger

15 Tightening lever for protective

hood

16 Cutting disc

17 Protective hood

18 Mounting ange

19 Clamping nut

20 Mounting spindle

21 Adjustment nut

Technical data

Angle Grinder PWSA 18 A1:

Rated input voltage

................................................. 18 V

Measurement idling speed (n) ...8000 min

-1

Dimensions of the cutting/roughing discs

................................. Ø 115 x 22,2 mm

Thickness of the cutting/roughing discs

............................................max. 6 mm

Grinding spindle thread ................... M14

Thread length of the grinding spindle

..........................................max. 14 mm

Protection category...........................IPX0

Sound pressure level

(L

pA

) ...................81,6 dB(A); K

pA

= 3 dB

Sound power level (L

wA

)

measured ...........92,6 dB(A); K

wA

= 3 dB

guaranteed ........................... 96 dB(A)

Vibration values (a

h

)

Main handgrip ... 3,043 m/s

2

K= 1,5 m/s

2

Additional handle 5,024 m/s

2

K= 1,5 m/s

2

6

GB

Battery (Li-Ion) ...........PAP18-2.6A1

Number of battery cells................. ..10

Nominal voltage ...................... 18 V

Capacity .................................. 2,6 Ah

Charging time ..........................ca. 1 h

Recharger ................JLH-H260-18G

Nominal consumption ................. 70 W

Uptake voltage/Input

....................... 220-240 V~, 50-60 Hz

Voltage output/Output

.............................. 18 V

2600 mA

Protection class ............................

II

Protection category ...................... IPX0

The vibration values represent maximum

values which have been determined with

the supplied cutting disc. The actual vibra-

tion values may vary depending on the

used accessories. The vibration values are

still affected by the handling of the user’s.

Cutting disc (extent of delivery):

Idling speed n

0

................................... max.13300 min

-1

Disc speed ....................... max. 80 m/s*

Outer diameter ................... Ø 115 mm

Bore hole .......................... Ø 22,2 mm

Thickness ................................2,4 mm

*

The grinding disc must keep a rotational

speed of 80 m/s

Noise and vibration values have been

determined according to the standards and

regulations mentioned in the declaration of

conformity.

Technical and optical changes may be

undertaken in the course of further devel-

opment without notice. All dimensions,

references and information in this instruc-

tion manual are therefore not guaranteed.

Legal claims made on the basis of the

instruction manual can therefore not be

considered as valid.

The stated vibration emission value was

measured in accordance with a standard

testing procedure and may be used to com-

pare one power tool to another.

The stated vibration emission value may

also be used for a preliminary exposure

assessment.

Warning:

The vibration emission value whilst

actually using the electrical tool may

vary from the given values indepen-

dently of the type and way in which

the electric tool is used.

Safety measures for the protection of

the operator are to be determined

that are based on an estimate of the

actual exposure under the real oper-

ating conditions (for this, all parts of

the operating cycle are to be taken

into account, for example, times in

which the electric tool is turned off,

and those during which it is turned

on but running without a load).

Notes on safety

Caution! When using power tools,

observe the following basic safety

measures for the prevention of elec-

tric shocks and the risk of injury and

re.

Please read all these instructions be-

fore using this electric tool and please

keep the safety instructions.

7

GB

Symbols on the battery:

Do not dispose of

batteries in house-

hold waste, re or

water.

Do not subject the battery to strong

sunlight over long periods and

do not leave it on a heater (max.

45°C).

Take batteries to an old battery

collection point where they will

be recycled in an environmentally

friendly manner.

Symbols on the recharger:

Warning!

Before using for the rst time, care-

fully read through the user manual

The recharger is for indoor use

only.

130°C

Miniature fuse

Protection class II

Electrical appliances must not be dis-

posed of with the domestic waste.

Green LED ashes up without battery

Charger ready

Green LED lights up

Battery such alleged charged

Red LED lights up Battery charging

T2,5A

Symbols and icons

Symbols on the device:

Warning!

Risk of injury from the rotating tool!

Keep hands away

Warning! Electric shock hazard.

Always unplug the device before

working on it

Read the manual!

Wear ear protection

Wear eye protection

Wear breathing protection

Risk of cuts!

Wear cut-resistant gloves

Electrical machines do not belong

with domestic waste

Other symbols on the

cutting disc:

Do not use for side grinding

Do not use for wet grinding

Do not use defective discs

Suitable for metal

Wear safety shoes

8

GB

Green LED ashes with battery:

Battery has to be charged in advance for

30 minutes before charging starts

Red and green LED ashes Battery defect

Red and green LED lights up

Battery too cold or too warm. Battery can-

not be charged

Symbols in the manual

Warning symbols with in-

formation on damage and

injury prevention.

Instruction symbols (the instruction is

explained at the place of the excla-

mation mark) with information on

preventing damage.

Help symbols with information on

improving tool handling.

General Safety Directions for

Power Tools

WARNING! READ ALL SAFETY

DIRECTIONS AND INSTRUC-

TIONS. Omissions in the compliance

with safety directions and instructions

can cause electrical shock, re and/

or severe injuries.

Retain all safety directions and in-

structions for future use.

The term „power tool“ in the warnings refers

to your mains-operated (corded) power tool

or battery-operated (cordless) power tool).

1) Work area safety :

a) Keep work area clean and well

lit. Cluttered or dark areas invite acci-

dents.

b) Do not operate power tools in

explosive atmospheres, such as

in the presence of ammable

Iiquids, gases or dust. Power tools

create sparks which may ignite the dust or

fumes.

c) Keep children and bystanders

away while operating a power

tool. Distractions can cause you to lose

control.

2) Electrical safety :

CAUTION! The following states how

to avoid accidents and injuries due to

electric shock:

a) Power tool plugs must match the

outlet. Never modify the plug in

any way. Do not use any adapter

plugs with earthed (grounded)

power tools. Unmodied plugs and

matching outlets will reduce risk of electric

shock

b) Avoid body contact with earthed

or grounded surfaces, such as

pipes, radiators, ranges and re-

frigerators. There is an increased risk

of electric shock if your body is earthed or

grounded.

c) Do not expose power tools to rain

or wet conditions. Water entering a

power tool will increase the risk of electric

shock.

d) Do not abuse the cord. Never use

the cord for carrying, pulling or

unplugging the power tool. Keep

cord away from heat, oil, sharp

edges or moving parts. Damaged or

entangled cords increase the risk of elec-

tric shock.

e) When operating a power tool out-

doors, use an extension cord suit-

able for outdoor use. Use of a cord

suitable for outdoor use reduces the risk of

9

GB

electric shock.

f) If operating a power tool in a

damp location is unavoidable, use

a residual current device (RCD)

protected supply. Use of an RCD

reduces the risk of electric shock. Use a

circuit breaker with a current limit of

30 mA or less.

3) Personal safety:

CAUTION! The following states how

to avoid accidents and injuries:

a) Stay alert, watch what you are

doing and use common sense

when operating a power tool. Do

not use a power tool while you

are tired or under the inuence of

drugs, alcohol or medication. A mo-

ment of inattention white operating power

tools may result in serious personal injury.

b) Use personal protective equip-

ment. Always wear eye protec-

tion. Protective equipment such as dust

mask, non-skid safety shoes, hard hat, or

hearing protection used for appropriate

conditions will reduce personal injuries.

c) Prevent unintentional starting.

Ensure the switch is in the off-po-

sition before connecting to power

source and/or battery pack, pick-

ing up or carrying the tool. Carry-

ing power tools with your nger on the

switch or energising power tools that have

the switch on invites accidents.

d) Remove any adjusting key or

wrench before turning the power

tool on. A wrench or a key left attached

to a rotating part of the power tool may

result in personal injury.

e) Do not overreach. Keep proper

footing and balance at all times.

This enables better control of the power

tool in unexpected situations.

f) Dress properly. Do not wear loose

clothing or jewellery. Keep your

hair, clothing and gloves away

from moving parts. Loose clothes,

jewellery or long hair can be caught in

moving parts.

g) If devices are provided for the

connection of dust extraction and

collection facilities, ensure these

are connected and properly used.

Use of dust collection can reduce dust-

related hazards.

4) Power tool use and care :

a) Do not force the power tool. Use

the correct power tool for your

application. The correct power tool will

do the job better and safer at the rate for

which it was designed.

b) Do not use the power tool if the

switch does not turn it on and off.

Any power tool that cannot be controlled

with the switch is dangerous and must be

repaired.

c) Disconnect the plug from the

power source and/or the battery

pack from the power tool before

making any adjust -ments, chang-

ing accessories, or storing power

tools. Such preventive safety measures

reduce the risk of starting the power tool

accidentaIly.

d) Store idle power tools out of the

reach of children and do not al-

low persons unfamiliar with the

power tool or these instructions to

operate the power tool. Power tools

are dangerous in the hands of untrained

users.

e) Maintain power tools. Check for

misalignment or binding of mov-

ing parts, breakage of parts and

any other condition that may af-

10

GB

fect the power tool’s operation.

If damaged, have the power tool

repaired before use. Many accidents

are caused by poorly maintained power

tools.

f) Keep cutting tools sharp and

clean. Properly maintained cutting tools

with sharp cutting edges are less Iikely to

bind and are easier to control.

g) Use the power tool, accessories

and tool bits etc. in accordance

with these instructions, taking into

account the working conditions

and the work to be performed.

Use of the power tool for operations dif-

ferent from those intended could result in

a hazardous situation.

5) CAREFUL HANDLING AND USE OF

BATTERY DEVICES

a) Charge the batteries only in charg-

ers that are recommended by the

manufacturer. Risk of re if a charger

that is suitable for a specic type of bat-

tery is used with other batteries.

b) In the power tools, use only the

batteries designed for the pur-

pose. The use of other batteries may

result in injuries and risk of re.

c) Keep the unused battery away

from paper clips, coins, keys,

nails, screws and other small

metal objects, which could cause

bridging of the contacts. A short

circuit between the battery contacts may

cause burns or re.

d) If used incorrectly, liquid may leak

from the battery. Avoid contact

with this. In the event of accidental

contact, rinse off with water. If the

liquid gets into eyes, seek medical

assistance. Leaking battery uid may

cause skin irritations or burns.

6) SERVICE

Have your power tool serviced by

a qualied repair person using

only identical replacement parts.

This will ensure that the safety of the power

tool is maintained.

7) SPECIAL SAFETY DIRECTIONS FOR

BATTERY-OPERATED TOOLS

a) Ensure that the device is switched

off before inserting the battery.

Inserting a battery into a power tool that is

switched on may result in accidents.

b) Recharge the batteries indoors

only because the battery charger

is designed for indoor use only.

c) To reduce the electric shock haz-

ard, unplug the battery charger

from the mains before cleaning

the charger.

d) Do not subject the battery to

strong sunlight over long periods

and do not leave it on a heater.

Heat damages the battery and there is a

risk of explosion.

e) Allow a hot battery to cool before

charging.

f) Do not open up the battery and

avoid mechanical damage to the

battery. Risk of short circuit and fumes

may be emitted that irritate the respiratory

tract. Ensure fresh air and seek medical as-

sistance in the event of discomfort.

g) Do not use non-rechargeable bat-

teries!

8) CORRECT HANDLING OF THE BAT-

TERY CHARGER

a) This device can be used by children

aged 8 and over and by people with

reduced physical, sensory or mental

11

GB

capacities or with a lack of experience

or knowledge, if they are supervised or

have been instructed regarding safe use

of the device and understand the result-

ing risks. Children are not permitted to

play with the device. Cleaning and user

maintenance are not to be undertaken

by children without supervision.

b) Children should be supervised to ensure

that they do not play with the appliance.

c) To charge the battery, use only the

charger supplied.

Risk of re and explosion. This ensures that

the safety of the device is maintained.

d) Before each use, check the charg-

er, cable and plug and have them

repaired by qualied profession-

als and only with original parts.

Do not use a defective charger and do not

open it up yourself. This ensures that the

safety of the device is maintained.

e) Connect the charger only to a

socket with an earth. Ensure that

the mains voltage matches the

specications on the charger rat-

ing plate. Risk of electric shock.

f) Disconnect the charger from the

mains before closing or opening

connection to the battery / power

tool / device.

g) Keep the charger clean and away

from wet and rain. Do not use the

charger outdoors. Dirt and the entry of

water increase the risk of electric shock.

h) Operate the charger only with

the appropriate original batteries.

Charging other batteries may result in inju-

ries and risk of re.

i) Avoid mechanical damage to the

charger. This can result in internal short

circuits.

j) Do not operate the charger on a

combustible surface (e.g. paper,

textiles). Risk of re due to heating dur-

ing charging.

k) If the power cable for this equipment is

damaged, it must be replaced by the

manufacturer, a customer service agent of

the same or a similarly qualied person in

order to prevent hazards.

l) The battery of the appliance is not fully

charged at the time of delivery. It therefore

needs to be fully recharged before you use

it for the rst time. For the rst recharge

cycle we recommend that you charge the

battery for about 1 hour. Slot the battery

into the base and plug the battery charger

into a mains outlet.

m) When the battery is fully charged, unplug

the charger from the mains and from the

appliance. Charging time is approx. 1

hour.

n) Do not charge the battery continuously

since this may damage the battery cells.

Note: Repeatedly charging small ca-

pacities may damage the battery cells.

Recharge the battery only if the appliance

is becoming slow.

o) Do not use the charger to charge non-

rechargeable batteries.

9) RESIDUAL RISKS

Even if properly operating and handling this

electric tool, some residual risks will remain.

Due to its construction and build, this electric

tool may present the following hazards:

a) Cuts

b) Ear damage if working without ear protec-

tion.

c) Damage to your health caused by swing-

ing your hands and arms when operating

the appliance for longer periods of time or

if the unit is not held or maintained prop-

erly.

Warning! During operation, this elec-

tric tool generates an electromagnetic

12

GB

eld which, under certain circum-

stances, may impair the functionality of

active or passive medical implants. To

reduce the risk of serious or lethal inju-

ries, we recommend that persons with

medical implants consult their doctor

and the manufacturer of their medical

implant before operating the machine.

Safety instructions for all ap-

plications

Common safety instructions for

grinding, sanding, working with

wire brushes and cutting grinders:

• This electric tool is to be used as

a grinder, sander, wire brush

and cutting grinder. Follow all

safety instructions, directives, il-

lustrations and facts which you

receive with the device. If you do

not follow these instructions, an electri-

cal shock, re and/or serious injury

may occur.

• This electric tool is not suitable

for cup brushes. Using the electric

tool in ways for which it is not intended

may cause hazards and injuries.

• This electric tool is not suitable

for cup wheels, mounted points

or grinding cones. Using the electric

tool in ways for which it is not intended

may cause hazards and injuries.

• This electric tool is not suitable

for polishing. Using the electric tool

in ways for which it is not intended may

cause hazards and injuries.

• Do not use any accessories that

are not specically intended and

recommended for this electric

tool by the manufacturer. Simply

because an accessory can be attached

to your electric tool does not guarantee

safe operation.

• The allowable rotation speed of

the attachment tools must be at

least as high as the highest rota-

tion speed indicated on the elec-

tric tool. Accessories that run faster

than the allowable speed can break

and y apart.

• The outside diameter and thick-

ness of the attachment tool must

correspond to the dimensions

indicated for your electric tool.

Attachment tools which are wrongly

dimensioned cannot be sufciently

shielded or controlled.

• Attachment tools with threaded

attachment must t the thread-

ing of the grinding spindle ex-

actly. For attachment tools which

are mounted through a ange,

the diameter of the hole in the

attachment tool must t the

mounting diameter of the ange.

Attachment tools which cannot be pre-

cisely attached to the electric tool turn

unevenly, vibrate very strongly and can

ultimately lead to a loss of control.

• Never use damaged attachment

tools. Check attachment tools

such as grinding discs for chip-

ping or cracks, grinding plates

for cracks, wear or strong abra-

sion and wire brushes for loose

or broken wires before using

them. If the electric tool or the

attachment tool falls off, check

whether it is damaged or, use

an undamaged attachment tool.

If you have checked the at-

tachment tool and attached it,

keep yourself and any nearby

persons beyond the level of the

rotating attachment tool and al-

low the device to run for 1 min.

13

GB

at the highest rotational speed.

Damaged tools usually break during this

test period.

• Wear personal safety equip-

ment. Depending on the applica-

tion, use full face shields, eye

protection or safety goggles.

In so far as it is appropriate,

wear dust masks, ear protec-

tion, gloves or special aprons

which keep small grinding and

material particles away from

you. Eyes should be protected from the

foreign matter which can be caused to

y during the various applications. Dust

or breathing masks should lter the dust

that is created during operation. If you

are exposed to loud noise for a long

time, you may suffer hearing loss.

• Ensure that other people are at

a safe distance to your work-

ing area. Anyone who enters

the working area should wear

personal protective equipment.

Broken bits from the piece being worked

or broken attachment tools can y away

and cause injuries even beyond the di-

rect working area.

• Hold the electric tool only by

the insulated gripping surfaces

when performing work in which

the cutting tool may come into

contact with hidden wiring or its

own cord. Contact with a live wire

can also cause a charge in metal parts

of the device and result in an electric

shock.

• Keep the cord away from the ro-

tating attachment tool. If you lose

control of the device, the power cord

can become separated or caught and

your hand or arm may be pulled into

the rotating attachment tool.

• Never put the electric tool down

before the attachment tool has

come to a full stop. The rotating

attachment tool can come into contact

with the surface upon which it is set,

whereby you could lose control of the

electric tool.

• Never allow the electric tool to

run whilst you are carrying it.

Your clothing may accidentally come

into contact with the rotating attachment

tool and get caught and the attachment

tool could drill into your body.

• Clean the ventilation slots of

your electric tool routinely. The

motor air pulls dust into the housing

and, should too much metallic dust col-

lect, could cause electrical hazards.

• Never use the electric tool near

ammable material. Sparks could

ignite this material.

• Do not use attachment tools

which require liquid coolant.

Using water or another liquid coolant

could lead to electrical shock.

Additional safety instructions

• Connect the appliance only to a power

socket with a residual current circuit

breaker of rated residual current no

more than 30 mA.

• Keep power cords and extension cords

away from the disc. If they are dam-

aged or cut through, immediately pull

the plug from the outlet. Do not touch

the cable before it has been discon-

nected from the power supply.

Risk of electric shock!

• The replacement of the plug or the con-

nection line must always be executed

by the manufacturer of the electric tool

or his/her customer service in order to

avoid any hazards.

• Only use grinding discs where the in-

14

GB

dicated rotational speed is at least as

high as what has been specied on the

name plate of the device.

• Carry out a visual inspection of the

grinding disc before use. Do not use

any damaged or deformed grinding

discs. Replace any damaged or worn

grinding discs.

• Make sure that the sparks produced by

grinding do not present a danger, e.g.

reach people or ignite ammable sub-

stances.

• Always wear safety goggles, safety

gloves, respiratory protection and ear

protection when grinding, brushing and

cutting.

• Never keep the ngers between the

grinding disc and spark protection or in

close proximity to the protective hoods.

There is a risk of crushing.

• The rotating parts of the device cannot

be covered due to functional reasons.

Therefore, proceed cautiously and hold

the workpiece rmly in order to avoid

slipping which could cause your hands to

come into contact with the grinding disc.

• The workpiece gets hot during grind-

ing. Do not touch the machined area,

allow it to cool down. There is a risk of

burning. Do not use coolants or the like.

• If you are tired or have consumed al-

cohol or tablets, do not work with the

device. Always have a break on time.

• Turn off the appliance and, before do-

ing any servicing, remove the battery.

RESIDUAL RISKS

Even if properly operating and handling this

electric tool, some residual risks will remain.

Due to its construction and build, this electric

tool may present the following hazards:

a) Cuts

b) Ear damage if working without ear pro-

tection.

c) Damage to your health caused by swing-

ing your hands and arms when operat-

ing the appliance for longer periods of

time or if the unit is not held or main-

tained properly.

d) Health injuries which result from swing-

ing hand and arm, in the event that the

device is used over a longer period

of time or is not used and maintained

properly.

Warning! During operation, this elec-

tric tool generates an electromagnetic

eld which, under certain circum-

stances, may impair the functionality

of active or passive medical implants.

To reduce the risk of serious or lethal

injuries, we recommend that persons

with medical implants consult their

doctor and the manufacturer of their

medical implant before operating the

machine.

Kickback

Kickback is the sudden reaction from a chop-

ping or blocked grinder attachment such as a

grinding disc, grinding plate, wire brush etc.

Chopping or blocking leads to sudden stop-

ping of the rotating attachment. This causes

an uncontrolled electric tool to accelerate in a

direction counter to the rotational direction of

the attachment tool. If, for example, a grind-

ing disc cuts into the workpiece or blocks it,

the edge of the grinding disc that digs into

the workpiece can get caught and, through

that, break off the grinding disc or cause a

kickback. The grinding disc then moves to-

wards or away from the operator, depending

on the direction of rotation of the disc at the

blocked spot. Here, the grinding discs can

also break. A kickback is caused by wrongly

or incorrectly operating the electric tool. It can

be avoided by suitable cautionary measures,

15

GB

such as described below.

a) Hold the electric tool very

rmly and bring your body and your

arm into a position in which you can

resist the kickback force. Always use

the supplemental handle if available to

give you the best control over kickback

force or reaction time during accel-

eration. The operator can master the

kickback and reaction force through

suitable precautions.

b) Never bring your hands near a

rotating attachment tool. The at-

tachment tool can run over your hand

in the kickback.

c) Keep your body away from the

area in which the electric tool

would move during a kickback.

The kickback drives the electric tool in

the counter-direction to the rotation of

the grinding disc at the blocked spot.

d) Work particularly cautiously in

corner areas or where there are

sharp corners etc. Prevent the at-

tachment tools from recoiling from the

workpiece and jamming. The rotating

attachment tool tends to jam when near

corners, sharp edges or when it recoils

from such. This causes a loss of control

or kickback.

e) Do not use chain or toothed

saw blades. Such attachment tools

frequently cause a kickback or loss of

control over the electric tool.

Special safety instructions for

grinding and cutting

a) Use only grinders which have

been approved for your electric

tool and the protective hood in-

tended for these grinders. Grind-

ers which are not intended for the elec-

tric tool may not be sufciently shielded

and are unsafe.

b) Depressed centre grinding

wheels must be pre-mounted in

such a way that their grinding

surface does not protrude over

the level of the edge of the pro-

tective cover. An incorrectly mounted

grinding wheel which protrudes beyond

the level of the edge of the protective

cover cannot be adequately shielded.

c) The protective hood must be

securely attached to the elec-

tric tool and adjusted so that

the greatest level of safety is

reached, i.e., the smallest possible

amount of the grinder is exposed to the

operator. The protective hood should

protect the operator from broken bits

and accidental contact with the grinder.

d) Grinders may only be used for

the recommended attachment

options. For example: Never grind

with the side surface of a cutting disc.

Cutting discs are for cutting material

using the edge of the disc. Pushing

sideways on these grinders can break

them.

e) Always use undamaged clamp-

ing anges of the correct size

and shape for the grinding disc

you selected. Suitable anges sup-

port the grinding disc and thus reduce

the danger of the grinding disc break-

ing. Flanges for cutting discs can be

distinguished from anges for other

grinding discs.

f) Do not use worn grinding discs

for larger electric tools. Grinding

discs for larger electric tools are not

set up for the higher rotation speeds of

16

GB

smaller electric tools and can break.

Other special safety instructions for

cutting grinding

a) Avoid blocking the cutting disc

or pressing down too hard. Do

not make any excessively deep cuts.

Overloading the cutting disc increases

wear and its tendency to tilt or block

and, with that, to kickback or break the

grinder.

b) Avoid the area in front of and

behind the rotating cutting disc.

When you move the cutting disc by

itself in the workpiece, in the event that

the electric tool kicks back with the ro-

tating disc, it can spin directly towards

you.

c) If the cutting disc jams, or you

interrupt your work, switch the

device off and hold it until the

disc has come to a full stop.

Never try to pull the cutting disc out of

the cut while it is still running, because

it can kick back. Identify and correct

the cause of the jamming.

d) Do not switch the electric tool

on again as long as it is in the

workpiece. Allow the cutting disc

to rst reach its full rotational speed

before you carefully resume with the

cutting. Otherwise, the disc may catch,

spring away from the workpiece or

cause a kickback.

e) Support plates or workpieces

to reduce the risk of kickback

from a jammed cutting disc. Large

workpieces may bend under their own

weight. The workpiece must be sup-

ported on both sides of the disc, near

the cutting disc as well as also at the

edge.

f) Be particularly careful for pocket

cuts in existing walls or other

areas where you cannot see

what is there. The cutting disc may

cause a kickback when it cuts into gas

or water lines, electrical lines or other

hidden objects.

Additional safety instructions for

sanding

Special safety instructions for sanding:

• Do not use overly large sandpa-

per sheets; follow the manufac-

turer‘s information for sandpa-

per sizes. Sandpaper sheets which

extend beyond the sanding plate can

cause injuries and can block, tear the

sandpaper, or cause kickback.

Additional safety instructions for

working with wire brushes

Special safety instructions for working with

wire brushes:

• Be aware that the wire brushes

also lose wire pieces during

typical use. Do not overload

the wires by pressing down too

hard. Flying wire pieces can very eas-

ily penetrate thin clothing and/or your

skin.

• If a protective hood is recom-

mended, do not allow the wire

brushes and the protective hood

to touch each other. The diameter of

plate and cup brushes can enlarge if too

much pressure and centrifugal force is

exerted.

17

GB

Charging the battery

Do not expose the battery to

extreme conditions such as

heat or impact. Risk of injury

from escaping electrolytic so-

lution! After eye/skin contact,

rinse the affected areas with

water or a neutraliser and

consult a doctor.

Charge the battery in a dry room

only.

Prior to attaching the charger, check

that the battery‘s outer surface is

clean and dry.

There is a risk of injury due to elec-

tric shock.

Only use the original charger from

the package to charge the battery.

Mind not to charge the appliance

for more than 1 hours at a time. If

you do, the battery and the appli-

ance may be damaged and longer

charging times would be a waste

of energy. Excessive charging will

void the warranty.

Make sure that the power supply

voltage matches the voltage rating

indicated on the device‘s type plate.

• Charge the battery before the rst time

of use. Do not briey charge the battery

several time in a row.

• Recharge the battery when you notice

that the appliance is becoming slower.

• If a fully recharged battery lasts for con-

siderably shorter operating times, the bat-

tery is used up and needs to be replaced.

Only use an OEM spare battery available

from our Customer Service.

• Always take heed of the applicable safety

instructions as well as the environmental

protection regulations and information.

• The warranty excludes all defects

caused by improper handling.

Removing / inserting the

battery

1. To remove the battery (9) from

the appliance, press the release

button 10) on the battery and

pull out the battery.

2. To insert the battery (9), place it

on the guide track and push it

back into the appliance. It will

audibly snap in.

Recharging the battery

1. Remove the battery (9) from the

appliance.

2. Insert the battery (9) in the charg-

ing compartment of the battery

charger.

3. Plug the battery charger into a

mains outlet.

4. When the battery (9) is fully

recharged unplug the battery

charger from the mains.

5. Pull the battery (9) out of the bat-

tery charger.

Green LED ashes up without battery

Charger ready

Green LED lights up

Battery such alleged charged

Red LED lights up Battery charging

Green LED ashes with battery:

Battery has to be charged in advance for

30 minutes before charging starts

Red and green LED ashes Battery defect

Red and green LED lights up

Battery too cold or too warm. Battery can-

not be charged

18

GB

Used batteries

• If a fully recharged battery lasts for

considerably shorter operating times,

the battery is used up and needs to be

replaced. Only use an OEM battery

pack replacement available from our

Customer Service.

• Always take heed of the applicable safety

instructions as well as the environmental

protection regulations and information

(see “Cleaning and Maintenance”).

Checking the battery charge

level

The battery’s (9) charge level is indicated

by the charge state indicator (8).

Press the activation button battery indicator

on the battery.

The LEDs indicate the battery’s charge

level.

red-yellow-green =Battery fully charged

red and yellow =Battery half charged

red =Battery needs to be charged

Practical tips

Scrubbing wheels:

Never use a cutting wheel for

scrubbing !

Exert only moderate pressure on the work-

piece. Move the device evenly back and

forth.

A working angle of 30° to 40° achieves

the best results for scrub grinding.

Cutting disc:

Never use a scrubbing wheel

for cutting !

Only certied, bre-reinforced cutting or

grinding discs may be used.

In general, work with small scrubs. Exert

only moderate pressure on the workpiece.

Always work in the counter-direction. This

ensures that the device is not pushed out of

the cut through lack of control.

Cutting of stone materials:

• It is best to use a diamond cutting disc

to cut stone materials. Make sure in any

case that the cutting disc is suitable and

labelled for your application.

• When cutting stone materials, ensure

that the dust extraction is sufcient.

• Wear a dust protection mask.

• The device may only be used for dry

cutting/dry grinding.

Information on building statics:

Slits in structural walls are subject to the

standard DIN 1053 Part 1 or country-

specic regulations. These regulations must

be observed without fail. Before begin-

ning work you should ask the structural

engineer, architect or relevant construction

supervisor for advice.

Assembly

Caution! Risk of injury!

- Ensure that you have sufcient

space in which to work, and that

you do not endanger other peo-

ple.

19

GB

- All hoods and protective devices

must be assembled properly be-

fore commissioning.

- Disconnect the mains plug be-

fore changing the setting on the

device

Mount additional handgrip

The device must only be op-

erated with the handgrip

mounted.

Screw the additional handgrip (2), de-

pending on the type of work, to the left,

right or above the device using the thread-

ing for the handgrip (4).

Assemble/set protective

hood

Adjust the protective cover such that any

sparks or detached parts cannot hit either

the user or any bystanders.

The protective cover must also be posi-

tioned such that the sparks cannot ignite

combustible parts, including those in the

surroundings.

The device must only be

operated with the protective

hood mounted.

1. Open the tightening lever

(15).

2. Place the protective hood (17)

on the positioning holes.

3. Turn the protective hood (17) into

the working position. The closed

side of the protective hood must

always face the operator.

4. Close the tightening lever

(15) again. The protective hood

should not be able to be turned

any more.

If needed, the tension on the adjustment

nut (

21) can be set.

Installing/changing disc

1. Press the spindle stop button (3).

2. Release the clamping nut

(

19) with the chuck key

(1).

3. Set the desired disc onto the

mounting ange (

18). label

on the disc should always face

the device.

4. Set the clamping nut (

19) on

the mounting spindlel (

20)

again. The at side of the clam-

ping nut must face the attach-

ment tool.

5. Press the spindle stop button (3)

and pull the clamping nut (19)

tight again using the chuck key

(1).

Operation

Caution! Risk of injury!

- Always remove the mains plug

before working on the tool.

- Only use grinding discs and ac-

cessories recommended by the

manufacturer. Using other attach-

ment tools and other accessories

can represent a risk of injury for

you.

- Only use grinding tools which

bear information about the

manufacturer, type of binding,

dimension and permitted number

of revolutions.

- Only use grinding discs where

the printed rotational speed is at

20

GB

least as high as what has been

specied on the name plate of

the device.

- Do not use any broken, cracked,

or otherwise damaged grinding

discs.

- Never operate the device with-

out protective equipment.

- Support plates or workpieces to

reduce the risk of kickback from

a jammed cutting disc. Large

workpieces may bend under

their own weight. The workpiece

must be supported on both sides

of the disc, near the cutting disc

as well as at the edge.

Keep your hands away from

the disc when the device is in

operation. Risk of injury.

Information on replace-

ment:

• Never operate the device without

protective equipment.

• Ensure that the rotation speed

stated on the grinding disc is the

same or higher than the nominal

rotation speed of the device.

• Ensure that the grinding disc

dimensions match those of the

device.

• Only use awless grinding discs

(ringing test: when you strike the

grinding disc with a plastic ham-

mer, it results in a clear sound).

• Never re-drill a locating hole

which is too small to make it

larger.

• Never use separate bushings or

adapters in order to make grind-

ing discs with a hole that is too

large t the device.

• Do not use any saw blades.

• To clamp the grinding tools

only use the clamping ange

provided. The pads between the

clamping ange and the grind-

ing tools must be made of elastic

materials e.g., rubber, soft card-

board etc.

• Always reassemble the device

completely after replacing the

grinding disc.

Turn off the appliance and, before

doing any servicing, remove the

battery.

Wear protective gloves when chang-

ing the grinding discs in order to

avoid cutting damages.

The grinding disc nut must not be

screwed too tightly in order to

avoid breaking the disc and nut.

Turning on and off

1. Press the on switch to start the device.

Press the on/off switch (5).

2. To turn it off, release the on-off button.

The device turns off.

After switching on the device, wait until the

device has reached its max. speed. Only

then should you start with the work.

The disc still runs even after

the device has been switched

off. Risk of injury.

Trial run:

Always carry out a trial run before carry-

ing out your rst grinding procedure and

after every disc replacement. Switch the

device off immediately if the grinding disc

is not rotating smoothly, if considerable

Strona jest ładowana ...

Parkside PWSA 18 A1 Translation Of The Original Instructions

Parkside PWSA 18 A1 Translation Of The Original Instructions

w innych językach

Powiązane dokumenty

Inne dokumenty