Flymo Turbo 400 Instrukcja obsługi

Marka: Flymo

Model: Turbo 400

Kategoria: Kosiarki

Typ: Instrukcja obsługi

Niniejsza instrukcja jest również odpowiednia dla

IMPORTANT INFORMATION

Read before use and retain for future reference

WICHTIGE INFORMATION

Bitte vor dem Benutzen des Gerätes

durchlesen und gut aufbewahren

RENSEIGNEMENTS IMPORTANTS

A lire avant usage et à conserver pour

référence ultérieure

BELANGRIJKE INFORMATIE

Leest u deze informatie voor het gebruik en

bewaar ze voor toekomstige raadpleging

VIKTIG INFORMASJON

Les bruksanvisningen nøye før bruk og

oppbevar den for senere bruk

VIKTIG INFORMATION

Läs anvisningarna före användningen och

spara dem för framtida behov

VIGTIGE OPLYSNINGER

Du bør læse brugsanvisningen før brug og

gemme til senere henvisning

INFORMACIÓN IMPORTANTE

Léase antes de utilizar y consérvela como

referencia en el futuro

INFORMAÇÕES IMPORTANTES

Leia antes de utilizar e guarde para consulta

futura

INFORMAZIONI IMPORTANTI

Leggere prima dell’uso e conservare per

ulteriore consultazione

TÄRKEÄÄ TIETOA

Lue tämä ennen käyttöä ja säilytä myöhempää

tarvetta varten

Záruka na tento produkt nebude uznaná v

prípade porúch spôsobených nesprávnou

obsluhou alebo používaním výrobku na iný

účel alebo iným spôsobom, ako je uvedené.

Pred začatím práce si prosím dôkladne

prečítajte návod na obsluhu a tento si aj pre

prípad potreby uschovajte

Garancija ne velja ob nepravilni uporabi

proizvoda in/ali ob uporabi za drugi namen

kot je izdelan. Prosimo, da pred uporabo,

preverite pazljivo navodila za obratovanje in

jih shranite za kasnejšo rabo.

Jótállást vállalni csak rendeltetésszerűen

használatba vett gépekre tudunk. Kérjük,

hogy a gép használatba vétele elött

gondosan olvassa el a kezelési utasításokat.

Gwarancja traci ważność w przypadku

używania urządzenia do celów innych niż

wymienione w instrukcji obsługi. Prosimy o

uważne przeczytanie instrukcji oraz o

stosowanie się do zaleceń i wskazówek w

niej zawartych

Záruka se nebude vztahovat na závady

způsobené nesprávným používáním, nebo

jestliže bude výrobek použit pro jiné účely

než pro jaké byl vyroben, nebo také jinak

než je uvedeno v návodu k obsluze. Tento

návod si přečtěte, prosím, velmi pozorně a

uchovejte jej pro možné budoucí odkazy

Turbo Lite 330/350

Turbo 400

A B

Turbo Lite 330

Turbo Lite 350/Turbo 400

GB - CONTENTS

1. Upper handle

2. Cable clip

3. Nut (if applicable)

4. Plastic handle knob

5. Washer

6. Bolt

8. Lower handle

9. Fixing pin

9. Spanner/scraper tool

10. Cutting height spacers (Turbo

Lite 330 - 1 fitted to

lawnmower & 2 in loose parts

pack) (Turbo Lite 350/Turbo

Lite 350/Turbo 400 - 1 fitted to

lawnmower & 3 in loose parts

pack)

11. Instruction Manual

12. Warning Label

13. Product Rating Label

D - INHALT

1. Oberer Griff

2. Kabelhalter

3. Mutter (falls vorhanden)

4. Griffknopf

5. Unterlegscheibe

6. Bolzen

7. Unterer Griff

8. Paßstift

9. Schraubenschlüssel/

Reinigungswerkzeug

10. Schnitthöhen-Distanzscheiben

(Turbo Lite 330 - 1 befindet sich

am Rasenmäher & 2 werden lose

in einem Beutel geliefert), (Turbo

Lite 350/Turbo 400 - 1 befindet

sich am Rasenmäher & 3 werden

lose in einem Beutel geliefert)

11. Bedienungsanweisung

12. Warnetikett

13. Produkttypenschild

F - TABLE DES MATIÈRES

1. Guidon supérieur

2. Attache câble

3. Ecrou (si applicable)

4. Bouton de Guidon

5. Rondelles

6. Boulons

7. Guidon inférieur

8. Chevilles de fixation

9. Raclette

10. Rondelles de réglage (Turbo

Lite 330 - 1 montée sur la

tondeuse et 2 dans les pièces

détachées), (Turbo Lite

350/Turbo 400 - 1 montée sur

la tondeuse et 3 dans les

pièces détachées)

11. Manuel d’Instructions

12. Etiquette d’avertissement

13. Plaquette des

Caractéristiques du Produit

NL - INHOUD

1. Bovenstuk van duwboom

2. Snoerklem

3. Moer (indien van toepassing)

4. Knop voor duwboom

5. Pakkingring

6. Bout

7. Onderstuk van duwboom

8. Bevestigingspin

9. Moersleutel/schraapinstrument

10. Snijhoogte-tussenstukken

(Turbo Lite 330 - 1 in

grasmaaimachine en 2 in pak

met losse onderdelen), (Turbo

Lite 350/Turbo 400 - 1 in

grasmaaimachine en 3 in pak

met losse onderdelen)

11. Handleiding

12. Waarschuwingsetiket

13. Product-informatielabel

N - INNHOLD

1. Øvre håndtak

2. Kabelklemmer

3. Mutter (om relevant)

4. Vingemuttere

5. Skiver

6. Håndtaksbolter

7. Nedre håndtak

8. Festebolt

9. Skrunøkkel/skrape

10. Avstandsstykker for justering

av klippehøyden (Turbo Lite

330 – 1 montert på

gressklipperen & 2 i pakken

med løse deler), (Turbo Lite

350/Turbo 400 – 1 montert på

gressklipperen & 3 i pakken

med løse deler)

11. Bruksanvisning

12. Advarselsetikett

13. Produktmerking

SF - SISÄLTÖ

1. Ylempi kahva

2. Johdon pidike

3. Mutteri (jos käytössä)

4. Kahvan nuppi

5. Tiivistysrengas

6. Pultti

7. Alempi kahva

8. Kiinnitystappi

9. Ruuviavain/kaavin

10. Leikkauskorkeuden säätölevy

(Turbo Lite 330 - 1 asennettu

ruohonleikkuriin ja 2

pakkauksessa), (Turbo Lite

350/Turbo 400 - 1 asennettu

ruohonleikkuriin ja 3

pakkauksessa)

11. Käyttöopas

12. Varoitusnimike

13. Ruohonleikkurin arvokilpi

S - INNEHÅLL

1. Övre handtag

2. Kabelklämma

3. Mutter (om sådan är

monterad)

4. Knopp för handtag

5. Bricka

6. Bult

7. Undre handtag

8. Fästbult

9. Skruvnyckel/Avskrapare

10. Distansbrickor för klipphöjd

(Turbo Lite 330 - 1 monterad

på gräsklipparen och 2 lösa i

förpackning), (Turbo Lite

350/Turbo 400 - 1 monterad

på gräsklipparen och 3 lösa i

förpackning)

11. Bruksanvisning

12. Varningsetikett

13. Produktmärkning

DK - INDHOLD

1. Øvre håndtag

2. Kabelklemme

3. Møtrik (hvis relevant)

4. Håndtagsknop

5. Spændeskive

6. Bolt

7. Nedre håndtag

8. Håndtagsstift

9. Skruenøgle/skrabeværktøj

10. Afstandsskiver til indstilling af

klippehøjde (Turbo Lite 330 - 1

monteret på plæneklipperen og

2 løse i posen) (Turbo Lite

350/Turbo 400 - 1 monteret på

plæneklipperen og 3 løse i

posen)

11. Brugsvejledning

12. Advarselsmœrkat

13. Produktets mærkeskilt

E - CONTENIDO

1. Empuñadura superior

2. Grapa de cable

3. Tuerca (si fuera aplicable)

4. Manija de empuñadura

5. Arandela

6. Perno

7. Empuñadura inferior

8. Pasador de fijación

9. Herramienta/raspador

10. Espaciadores de altura de

corte (Turbo Lite 330 – 1

instalado en el cortacésped y

2 en paquete de piezas

sueltas) (Turbo Lite

350/Turbo 400 – 1 instalado

en el cortacésped y 3 en

paquete de piezas sueltas)

11. Manual de instrucciones

12. Etiqueta de Advertencia

13. Placa de Características del

Producto

P - LEGENDA

1. Guiador superior

2. Grampo do cabo

3. Porca (se aplicável)

4. Maçaneta

5. Anilha

6. Cavilha

7. Guiador inferior

8. Parafuso

9. Chave de fendas

10. Espaçadores da altura de corte

(Turbo Lite 330 – 1 instalado na

máquina de cortar relva e 2 no

pacote de peças soltas), (Turbo

Lite 350/Turbo 400 – 1 instalado

na máquina de cortar relva e 3

no pacote de peças soltas)

11. Manual de Instrucções

12. Etiqueta de Aviso

13. Rótulo de Avaliação do

Produto

I - INDICE CONTENUTI

1. Impugnatura superiore

2. Morsetto per il cavo

3. Dado (se pertinente)

4. Manopola

5. Rondella

6. Bullone

7. Impugnatura inferiore

8. Perno di fissaggio

9. Chiave/raschietto

10. Distanziali altezza di taglio

(Turbo Lite 330 - 1 montato

sul tosaerba e 2 sfusi nel

sacchettino dei ricambi),

(Turbo Lite 350/Turbo 400 - 1

montato sul tosaerba e 3 sfusi

nel sacchettino dei ricambi)

11. Manuale di istruzioni

12. Etichetta di pericolo

13. Etichetta dati del prodotto

HU - TARTALOMJEGYZÉK

1. Felső tolókar

2. Kábelrögzítő

3. Anya (ha van)

4. Rögzítőgomb

5. Alátét

6. Csavar

7. Alsó tolókar

8. Rögzítőcsap

9. Csavarkulcs/térközbeállító

szerszám

10. Vágómagasság-beállítók

(Turbo Lite 330 - 1 db be van

szerelve, 2 db a külön

alkatrész-csomagolásban

található), (Turbo Lite

350/Turbo 400 - 1 db be van

szerelve, 3 db a külön

alkatrész-csomagolásban

található)

11. Kezelési útmutatő

12. Figyelmeztető címke

13. Termékminősítő címke

PL - ZAWARTOSC KARTONU

1. Górny uchwyt

2. Zaczep kabla

3. Nakrętka (jeżeli jest)

4. Gałka mocująca

5. Podkładka

6. Śruba

7. Dolny uchwyt

8. Sworzeń mocujący

9. Klucz/skrobak

10. Rozpórki ustalające wysokość

koszenia. (model Turbo Lite

330 - jedna rozpórka jest

zamontowana w kosiarce

natomiast dwie znajdują się w

pakiecie z luźnymi częściami).

(model Turbo Lite 350/Turbo

400 - jedna rozpórka jest

zamontowana w kosiarce

natomiast trzy rozpórki

znajdują się w pakiecie z

luźnymi częściami)

11. Instrukcja Obsługi

12. Znaki bezpieczeństwa

13. Tabliczka znamionowa

CZ - POPIS STROJE

1. Horní rukoje

2. Úchytka kabelu

3. Matice (pokud se používá)

4. Otočný knoflík na rukojeti

5. Podložka

6. Šroub

7. Spodní rukoje

8. Spojovací kolík

9. Klíč/nástroj pro čištění

10. Distanční tělíska výšky sekání

(Turbo Lite 330 - 1

instalováno na sekačce a 2 v

balíku s náhradními díly),

(Turbo Lite 350/Turbo 400 -

1 instalováno na sekačce a 3

v balíku s náhradními díly)

11. Návod k obsluze

12. Výstražný štítek

13. Typový štítek výrobku

SK - OBSAH

1. Vrchná rukovä

2. Svorka na kábel

3. Matka (ak aplikovate?né)

4. Kĺb rukoväte

5. Podložka

6. Skrutka

7. Spodná rukovä

8. Upevňovací kolík

9. K?úč/škrabka

10. Sekacie medzerníky výšky

(Turbo Lite 330 - 1 upevnený

ku kosačke a 2 v balíčku

vo?ných častí), (Turbo Lite

350/Turbo 400 - 1 upevnený

ku kosačke a 3 v balíčku

vo?ných častí)

11. Príručka

12. Varovný štítok

13. Prístrojový štítok

SL - VSEBINA

1. Zgornje držalo

2. Sponka za kabel

3. Matica (če je priložena)

4. Pritrdilna matica

5. Podložka

6. Vijak

7. Spodnje držalo

8. Pritrdilni trn

9. Ključ/strgalo

10. distančniki za višino reza

(Turbo Lite 330 - 1 montiran

v kosilnici in 2 v zavitku z

rezervnimi deli), (Turbo Lite

350/Turbo 400 - 1 montiran v

kosilnici in 3 v zavitku z

rezervnimi deli)

11. Priročnik

12. Opozorilna oznaka

13. Tipna tablica

(GB) CARTON CONTENTS

(D) KARTONINHALT

(F) CONTENU DU CARTON

(NL) INHOUD

(N) KARTONGEN

INNEHOLDER

(SF) PAKETIN SISÄLTÖ

(S) FÖRPACKNINGENS

INNEHÅLL

(DK) KARTONINDHOLD

(E) CONTENIDO DEL

CARTON

(P) LEGENDAS DOS

DESENHOS

(I) CONTENUTO

(HU) A DOBOZ TARTALMA

(PL) ZAWARTOŚĆ KARTONU

(CZ) OBSAH KRABICE

(SK) OBSAH BALENIA

(SL) VSEBINA ŠKATLE

SAFETY PRECAUTIONS

Explanation of Symbols on the

Turbo Lite 330/350/Turbo 400

Warning

Read the user instructions carefully to

make sure you understand all the

controls and what they do.

Always keep the lawnmower on the

ground when mowing. Tilting or lifting

the lawnmower may cause stones to

be thrown out

Keep bystanders away. Do not mow

whilst people especially children or

pets are in the mowing area

Switch off! Remove plug from mains

before adjusting, cleaning or if cable

is entangled or damaged. Keep the

cable away from the blade.

Beware of severing toes or hands.

Do not put hands or feet near a

rotating blade.

Blade continues to rotate after the

machine is switched off.

Wait until all machine components

have completely stopped before

touching them.

Do not mow in the rain or leave the

lawnmower outdoors while raining

General

1. Never allow children or people unfamiliar with

these instructions to use the mower. Local

regulations may restrict the age of the operator.

2. Only use the lawnmower in the manner and for

the functions described in these instructions.

3. Never operate the lawnmower when you are

tired, ill or under the influence of alcohol, drugs or

medicine.

4. The operator or user is responsible for accidents or

hazards occurring to other people or their property.

Electrical

1. The use of a Residual Current Device (R.C.D.)

with a tripping current of not more than 30mA is

recommended. Even with a R.C.D. installed

100% safety cannot be guaranteed and safe

working practice must be followed at all times.

Check your R.C.D. every time you use it.

2. Before use, examine cable for damage, replace it

if there are signs of damage or ageing.

3. Do not use the lawnmower if the electric cables

are damaged or worn

4. Immediately disconnect from the mains electricity

supply if the cable is cut, or the insulation is

damaged. Do not touch the electric cable until

the electrical supply has been disconnected. Do

not repair a cut or damaged cable. Replace it

with a new one.

5. Your extension cable must be uncoiled, coiled

cables can overheat and reduce the efficiency of

your mower.

6. Keep cable away from lawnmower, always work

away from the power point mowing up and down,

never in circles.

7. Do not pull cable around sharp objects.

8. Always switch off at the mains before

disconnecting any plug, cable connector or

extension cable.

9. Switch off, remove plug from mains and examine

electric supply cable for damage or ageing

befor

e winding cable for storage. Do not repair a

damaged cable, replace it with a new one. Use

only Flymo replacement cable.

10. Always wind cable carefully, avoiding kinking.

11. Never carry the product by the cable.

12. Never pull on the cable to disconnect any of the

plugs.

13. Use only on AC mains supply voltage shown on

the product rating label.

14. Our products are double insulated to EN60335.

Under no circumstance should an earth be

connected to any part of the product.

Cables

Use only 1.00mm

size cable up to 30 metres length

maximum.

Maximum rating:

1.00mm

size cable 10 amps 250 volts AC

1. Mains cables and extensions are available from

your local Electrolux Outdoor Products Approved

Service Centre.

2. Only use extension cables specifically designed

for outdoor use.

Preparation

1. Do not mow barefoot or in open sandals. Always

wear suitable clothing, gloves, and stout shoes.

2. Make sure the lawn is clear of sticks, stones,

bones, wire and debris; they could be thrown by

the blade.

If not used properly this lawnmower can be dangerous! This lawnmower can cause

serious injury to the operator and others, the warnings and safety instructions must be

followed to ensure reasonable safety and efficiency in using this lawnmower. The

operator is responsible for following the warning and safety instructions in this manual

and on the lawnmower.

ENGLISH - 1

STOP

SAFETY PRECAUTIONS

3. Before using the machine and after any impact,

check for signs of wear or damage and repair as

necessary.

4. Replace worn or damaged blades together with

their fixings in sets to preserve balance.

Use

1. Use the lawnmower only in daylight or good

artificial light.

2. Avoid operating your lawnmower in wet grass,

where feasible.

3. Take care in wet grass, you may lose your

footing.

4. On slopes, be extra careful of your footing and

wear non-slip footwear.

5. Mow across the face of slopes, never up and

down.

6. Exercise extreme caution when changing

direction on slopes. Walk never run.

7. Mowing on banks and slopes can be dangerous.

Do not mow on banks

or steep slopes.

8. Do not walk backwards when mowing, you could

trip.

9. Never cut grass by pulling the mower towards

you.

10. Switch off before pushing the mower over

surfaces other than grass.

11. Never operate the lawnmower with damaged

guards or without guards in place.

12. Keep hands and feet away from the cutting

means at all times and especially when switching

on the motor.

13. Do not tilt lawnmower when the motor is running,

except when starting and stopping. In this case, do

not tilt more than absolutely necessary and lift only

the part which is away from the operator. Always

ensure that both hands are in the operating position

before returning the appliance to the ground.

14. Never pick up or carry a mower when it is

operating or still connected to the mains supply.

15. Remove the plug from the mains :

- before leaving the mower unattended for any

period;

- before clearing a blockage;

- before checking, cleaning or working on the

appliance;

- if you hit an object. Do not use your lawnmower

until you are sure that the entire lawnmower is in

a safe operating condition.;

- if the lawnmower starts to vibrate abnormally.

Check immediately. Excessive vibration can

cause injury.

Maintenance and storage

1. Keep all nuts, bolts and screws tight to be sure

the lawnmower is in safe working condition.

2. Replace worn or damaged parts for safety.

3. Only use the replacement blade, blade bolt,

spacer and impeller specified for this product.

4. Be careful during adjustment of the lawnmower to

prevent entrapment of the fingers between

moving blades and fixed parts of the machine.

ENGLISH - 2

ASSEMBLY

A1 - lower handle

A2 - slots

A3 - fixing pin

Fitting the Lower Handles to Your Lawnmower (A)

1. Place the end of the lower handle into the slots.

2. Secure lower handles to hood by firmly pushing

fixing pin through holes in hood and handle.

3. Repeat on the other side.

• NOTE

Should a problem occur when securing handle to

hood with the fixing pin, carefully lever fixing pin

out of location and repeat steps 1 to 3 above.

B1 - lock off button, B2 - nut (if applicable)

B3 - handle knob, B4 - washer, B5 - bolt

Fitting Upper Handles to Lower Handles (B)

1. Ensure the upper handle is located correctly with

the lock-off button on the switchbox uppermost.

2. Ensure the upper handle and the lower handle

are aligned correctly.

3. Insert the nut into the handle knob. (if applicable)

4. Fit the bolts, washers and handle knobs.

5. Fit the cable to the handles with the clips

provided. Make sure the cable is not trapped

between the upper and lower handles.

HANDLE ADJUSTMENT

• WARNING! STOP THE LAWNMOWER AND

WAIT UNTIL THE BLADE HAS STOPPED

ROTATING BEFORE ADJUSTING THE

HANDLE.

• NOTE! REMOVAL OF LOWER HANDLE

FIXING PINS IS NOT REQUIRED

TO ADJUST

THE HANDLE

TO ADJUST THE HANDLE (C)

1. Hold handle as illustrated.

2. Take the weight of the handle with your right

hand...

3. ...then grip the lower part of the handle with your

left hand...

4. ...and pull

the lower handle towards you with

your left hand.

5. Move to forward or down position as required.

HANDLE IN FORWARD POSITION

Follow procedure described in "TO ADJUST THE

HANDLE" and push handle forward until it stops.

HANDLE IN DOWN POSITION

Follow procedure described in "TO ADJUST THE

HANDLE" and move handle downward until it stops..

NOTE - The handle does not rest flat on the

ground.

HANDLE IN OPERATING POSITION

Adjustment is not required to move the handle to

the operating position

Simply pull down from the forward position or

lift up

from the down position until the handle is in the most

comfortable operating position.

REMOVING AND FITTING THE BLADE AND FAN

K1 - Blade Bolt

K2 - Blade

K3 - Spacers

K4 - Fan

Removing the Blade and Fan

1. To remove the blade bolt, hold the fan firmly

and with the spanner provided loosen the blade

bolt by turning it anti-clockwise (L).

2. Remove the blade bolt, blade, spacers and fan.

3. Inspect for damage and clean as necessary.

• Renew your metal blade after 50 hours

mowing or 2 years whichever is the sooner -

regardless of condition.

Fitting the Blade and Fan

• If the blade is cracked or damaged replace

it with a new one.

• Never use a blade bolt if the insulated head

is damaged cracked or missing.

1. Ensure the fan is located correctly.

2. Place the spacers onto the fan ensuring the

pegs have located into the holes.

3. Place the blade onto the spacers ensuring the pegs

have located into the holes on the blade and ensuring

the blade is positioned as illustrated in Figure M.

4. Place the blade bolt through the centre hole of

the blade.(M)

5. Tighten down clockwise by hand.

6. Hold the fan firmly and tighten the blade bolt

with the spanner provided.

ENGLISH - 3

HOW TO MOW

1. Start mowing the edge of the lawn nearest to

the power point so the cable is laid out on the

lawn you have already cut. (J)

2. Cut your grass twice a week during the growing

season, your lawn will suffer if more than a third

of its length is cut at one time.

Do Not Overload Your Mower

Mowing long thick grass may cause the motor speed to

drop, you will hear a change in the motor sound. If the

motor speed drops you may overload your lawnmower

which may cause damage. When mowing in long thick

grass a first cut with the cutting height set higher will

help reduce the load. See Adjusting the Cutting Height.

STARTING AND STOPPING

To Start your Lawnmower

1. Connect female extension cable connector to

the back of the switchbox (D).

2. Form loop in mains cable and push the loop

through the slot as illustrated in picture (E)

3. To secure, position loop over the hook and pull

the cable back through the slot as illustrated in

picture (F).

4. Connect plug to mains and switch on.

5. To prevent a ring being cut in your lawn and to

clear any residual grass in the collection chute,

tilt your lawnmower slightly (G).

The switchbox is provided with a lock-off button

(H1) to prevent accidental starting.

6. Press and hold the lock-off button (H) on the

switchbox, then squeeze one of the Start/Stop

levers towards the upper handle (H).

7. Continue to squeeze the start/stop lever

towards the upper handle and release the lock-

off button.

8. When the lawnmower has reached full speed

gently lower it onto the lawn.

• NOTE

There are two start/stop levers fitted. Either

one can be used for starting the lawnmower.

• IMPORTANT

Do not use the start/stop levers

intermittently

To Stop your Lawnmower

1. To prevent a ring being cut in your lawn and to

clear any residual grass in the collection chute,

tilt your lawnmower slightly (G).

2. Release the pressure on the Start/Stop lever.

ADJUSTING THE CUTTING HEIGHT

Always handle the blade with care - sharp edges

could cause injury. USE GLOVES. Never use

more than 3 Cutting Height Spacers for the

Turbo Lite 330 OR 4 Cutting Height Spacers for

the Turbo Lite 350/Turbo 400. Spacers must

only be fitted between the blade and the fan and

NEVER between the blade and the bolt.

1. Remove the blade bolt, and blade as described

in Removing the Blade and Fan.

2. For a Lower Cut - Add spacers to a maximum

of 3 for Turbo Lite 330, or 4 for Turbo Lite

350/Turbo 400.

3. For a Higher Cut - Take spacers away.

4. Refit the blade as described in Fitting the

Blade and Fan.

SERVICE RECOMMENDATIONS

• Your product is uniquely identified by a silver and black product rating label.

• We strongly recommend that your product is serviced at least every twelve months, more often

in a professional application.

ENGLISH - 4

CARING FOR YOUR LAWNMOWER

Cleaning (USE GLOVES) (N)

It is very important that you keep your lawnmower

clean. Grass clippings left in any of the air intakes or

under the hood could become a potential fire hazard.

1. Remove grass from under the hood with a piece of

wood or similar.

2. Using a soft brush - remove grass clippings from

all

air intakes.

3. Remove the blade, see Figure L, to gain access to

the fan and clean with a soft brush.

4. Wipe over the surface of your lawnmower with a

dry cloth.

• IMPORTANT: Never use water for cleaning your

lawnmower. Do not clean with chemicals, including

petrol, or solvents - some can destroy critical plastic parts.

At the End of the Mowing Season

1. Replace blade, bolts, nuts or screws, if necessary.

2. Clean your lawnmower thoroughly.

3. Ask your local Service Centre to clean the air filter

thoroughly and carry out any service or repairs

required.

4. Make sure that the electric cable is coiled properly.

Carrying your Lawnmower Ensure the blade is facing

away from you.

Storing your Lawnmower

Store in a dry place where your lawnmower is protected

from damage.

FAULT FINDING HINTS

Fails to Operate

1. Is the Power Turned On?

2. Check the fuse in the plug, if blown replace.

3. Fuse continues to blow?

Immediately disconnect from the mains

electricity supply and consult your local

approved Service Centre.

Poor Flotation

1. Disconnect from the mains electricity supply.

2. Clean the underside of the hood and the fan

blades.

3. Raise to a higher height of cut. See Adjusting the

Height of Cut.

4. If poor flotation persists?

Disconnect from the mains electricity supply

and consult your local approved Service

Centre.

Excessive Vibration

1. Disconnect from the mains electricity supply.

2. Check that the blade is fitted correctly?

3. If the blade is damaged or worn, replace it with a

new one.

4. If vibration persists?

Immediately disconnect from the mains

electricity supply and consult your local

approved Service Centre.

GUARANTEE AND GUARANTEE POLICY

If any part is found to be defective due to faulty

manufacture within the guarantee period, Electrolux

Outdoor Products, through its Authorised Service

Repairers will effect the repair or replacement to the

customer free of charge providing:

(a) The fault is reported directly to the Authorised

Repairer.

(b) Proof of purchase is provided.

adjustment by the user.

(d) The failure has not occurred through fair wear and

tear.

(e) The machine has not been serviced or repaired,

taken apart or tampered with by any person not

authorised by Electrolux Outdoor Products.

(f) The machine has not been used for hire.

(g) The machine is owned by the original purchaser.

(h) The machine has not been used outside of the

country for which it was specified.

(i) The machine has not been used commercially.

* This guarantee is additional to, and in no way

diminishes the customers statutory rights.

Failures due to the following are not covered, therefore

it is important that you read the instructions contained in

this Operator's Manual and understand how to operate

and maintain your machine:

Failures not covered by guarantee

* Replacing worn or damaged blades

* Failures as a result of not reporting an initial fault.

* Failures as a result of sudden impact.

* Failures as a result of not using the product in

accordance with the instructions and

recommendations contained in this Operator's Manual.

* Machines used for hire are not covered by this

guarantee.

* The following items listed are considered as wearing

parts and their life is dependent on regular

maintenance and are, therefore not normally subject

to a valid warranty claim: Blades, Electric Mains cable.

* Caution! Electrolux Outdoor Products does not

accept liability under the warranty for defects

caused in whole or part, directly or indirectly by the

fitting of replacement parts or additional parts that

are not either manufactured or approved by

Electrolux Outdoor Products, or by the machine

having been modified in any way.

ENVIRONMENTAL INFORMATION

Electrolux Outdoor Products are manufactured under an

Environmental Management System (ISO 14001)

using, where practical, components manufactured in the

most environmentally responsible manner, according to

company procedures, and with the potential for

recycling at the end of the products’ life.

• Packaging is recyclable and plastic components

have been labelled (where practical) for

categorised recycling.

• Awareness of the environment must be considered

when disposing of ‘end-of-life’ product.

• If necessary, contact your local authority for

disposal information.

BELGIQUE/BELGIË Flymo Belgique/België

Tel: 02 363 0311, Fax: 02 363 0391

ČESKÁ REPUBLIKA Electrolux, spol. s.r.o., oz Electrolux Outdoor Products,

Na Křečku 365, Praha 10 - Horní Měcholupy.

Tel: 02/7847 0164, Info-linka: 0800/110 220

Internet: www.partner-flymo.cz E-mail: [email protected]

DANMARK Electrolux Outdoor Products, Flymo/Partner A/S,

Lundtoftegaardsvej 93A, DK 2800 Kgs.Lyngby

Tel: 45 87 75 77, Fax: 45 93 33 08, www.flymo-partner.dk

DEUTSCHLAND Flymo Deutschland

Tel: 097 21 7640, Fax:097 21 764202

ESTONIA Electrolux Estonia Ltd (Electrolux Eesti AS)

Tel: (372) 6650010

FRANCE Flymo France SNC

Tel 01 46 67 8141, Fax 01 43 34 2491

FINLAND SUOMI Electrolux Outdoor Products Finland

Tel: 00 358 9 39611, Fax: 00 358 9 3961 2644

ITALIA McCulloch Italiana s.r.l. - Via Como 72, 23868 Valmadrera

(LECCO) - ITALIA

Tel: 800 017829, Fax: 0341 581671

IRELAND Flymo Ireland

Tel: 01 4565222, Fax: 01 4568551

MAGYARORSZÁG Electrolux Lehel Kft

Tel: 00 36 1 251 41 47

NORGE Flymo/Partner, div. av Electrolux Motor a.s.

Tel: 69 10 47 90

NEDERLAND Flymo Nederland

Tel: 0172-468322, Fax: 0172-468219

ÖSTERREICH Husqvarna-Ges.m.b.H. Nfg. KG, Industriezeile 36, 4010 LINZ,

Tel: 0732 770101-0, Fax: 0732 770101-40,

email: [email protected] Internet: www.husqvarna.at

POLSKA Electrolux Poland Sp. z.o.o. Husqvarna, 01-612 Warszawa

Myslowicka 10/2

Tel:- (22) 8332949

SLOVENIJA Husqvarna-Ges.m.b.H. Nfg. KG, Industriezeile 36, 4010 LINZ,

Tel: 0732 770101-0, Fax: 0732 770101-40,

email: [email protected] Internet: www.husqvarna.at

SLOVENSKA Electrolux Slovakia s.r.o., Borova Sihot 211, 033 01 Lipt. Hradok

Tel: 044 522 14 19, Fax: 044 522 14 18, www.flymo-partner.sk

SCHWEIZ/SUISSE/SUIZZERA Flymo Schweiz/Suisse/Suizzera

Tel 062 889 93 50 / 889 94 25, Fax 062 889 93 60 / 889 94 35

SVERIGE Electrolux Outdoor Products, Sverige

Tel: 036 – 14 67 00, Fax: 036 – 14 60 70

UNITED KINGDOM Electrolux Outdoor Products United Kingdom

Tel: 01325 300303, Fax: 01325 310339

5119252-02

Electrolux Outdoor Products

Aycliffe Industrial Park

NEWTON AYCLIFFE

Co.Durham DL5 6UP

ENGLAND

Telephone - (00) 44 1325 300303 Fax - (00) 44 1325 310339

UK Telephone - 01325 300303 Fax - 01325 310339

Our policy of continuous improvement means that the specification of products may be altered from time to time without prior notice.

Electrolux Outdoor Products manufacture products for a number of well known brands under various registered patents, designs and

trademarks in several countries.

Registered number 974979 England

The Electrolux Group. The world’s No.1 choice.

The Electrolux Group is the world’s largest producer of powered appliances for kitchen, cleaning and outdoor use. More than 55 million

Electrolux Group products (such as refrigerators, cookers, washing machines, vacuum cleaners, chain saws and lawn mowers) are

sold each year to a value of approx. USD 14 billion in more than 150 countries around the world.

Flymo Turbo 400 Instrukcja obsługi

Marka: Flymo

Model: Turbo 400

Kategoria: Kosiarki

Typ: Instrukcja obsługi

Niniejsza instrukcja jest również odpowiednia dla

Pobierz PDF

raport

w innych językach

English: Flymo Turbo 400 User manual

Flymo Turbo 400 Instrukcja obsługi

Niniejsza instrukcja jest również odpowiednia dla

Flymo Turbo 400 Instrukcja obsługi

w innych językach

Powiązane artykuły

Inne dokumenty