Yamaha MKH-9200S Instrukcja obsługi

Yamaha
Marka
Yamaha
Model
MKH-9200S
Typ
Instrukcja obsługi

Ten podręcznik jest również odpowiedni dla

3 or 2 positions
First adjust the bracket position to a comfortable fit.
Attach the arms that are supplied with the
Multi Toms.
A
B
A
Lay the Marching Bells/Xylophone face down.
Use a hex wrench to loosen the four screws A on the carrier frame so that the
brackets can slide.
Set the carrier frame on the instrument, as shown in the illustration below, and slide
the brackets on the carrier frame so that they align with the carrier mounting plates
on the bottom of the instrument.
Use the four fixing bolts B on the brackets to attach the carrier frame to the instru-
ment. Tighten the four bolts little by little and secure.
Use the hex wrench to firmly tighten the carrier frame’s screws A .
* To remove the carrier frame, loosen the fixing wing bolts only.
* If you are having trouble reattaching the carrier frame after it has been removed, go
through the same procedure as described above.
CARRYING HOLDER for MARCHING BELLSXYLOPHONE
OWNER’S MANUAL
CAUTION
Accessories
Hexagonal Wrench
Thank you for purchasing the Yamaha Carrying Holder for
Marching Bells and Xylophones.
Please read this Owner’s Manual throughly before use.
Securely tighten all screws after adjusting the
instrument’s position. Loose screws may cause the
instrument to slip or produce noise during playing.
Therefore, always check and re-tighten all screws
before using the instrument.
To tighten the arm section screws, use the hexagonal
wrench provided.
Be very careful when removing the carrying holder and
drum. Never drop or throw them.
As far as possible, avoid using the drum and carrying
holder outside when it is raining. Wipe any wet parts
immediately with a soft, dry cloth.
To clean the carrying holder, wipe with a soft, dry cloth.
Never use solvents such as paint thinner or benzine.
When tilting up the marching bell/xylophone make sure
that the tone bars do not hit against the holder.
Always take suitable breaks when playing the
instrument for a long period of time.
When tilting up the marching
bells/xylophone always hold the
instrument with your hand as it
might flip back and injure bystanders.
When tilting the instrument up or
returning it to the playing position,
keep your hands away from
the areas marked A as
shown in the illustration.
Hands and/or fingers can
get caught in this area
resulting in injury.
A
Fixing wing bolt
ASSEMBLY PROCEDURE
Carrying Holder Setup Attach the Instrument
Carrier Frame
Pivot holder
Carrier mounting plate
Brackets with wing
bolts
Fixing wing bolt
A
A
A
A
B
B
B
B
Printed in Japan
R0
ZN39960
Bracket
Arm
Loosen
Tighten
One of three or two bracket mounting positions
can be selected.
(MKH-9200: 3 positions, MKH-9200S: 2 positions)
Insert the arms on the carrying holder into the carrier frame pivot holders.
C
Support the marching bells/xylophone and securely tighten the carrier frame pivot
holder screws
C using the Allen wrench provided.
ASSEMBLY PROCEDURE
Attaching to the Carrying Holder
Use the hexagonal wrench provided.
Carrier Frame
Insert
Insert
Insert the arms into the carrier frame pivot holders and decide the arm position, then
securely tighten the screws using the Allen wrench provided. Remove the carrier frame
after adjustment. Make sure that the instrument is attached to the carrier frame.
Arm Position Setup
Carrying holder
Carrying holder
Assembly should be performed by at least 2 persons on a flat surface.
Insert the arms into the frame pivot holders.
Use the hexagonal wrench provided.
Tighten
C
D
To adjust for a comfortable playing height, loosen the arm screws D and raise or lower
the arms as required.
After adjustment, securely tighten the screws using the Allen wrench provided.
ASSEMBLY PROCEDURE
Tone Bar Height Adjustment
Carrying holder
D
  • Page 1 1
  • Page 2 2

Yamaha MKH-9200S Instrukcja obsługi

Yamaha
Marka
Yamaha
Model
MKH-9200S
Typ
Instrukcja obsługi
Ten podręcznik jest również odpowiedni dla
ściągnij PDF
raport

w innych językach

Powiązane dokumenty

Inne dokumenty