MAIN COMPONENTS
UNDERBODY
DREAMCOLOR
INSTALLATION GUIDE
RIGID LIGHT BARS 36'' + 48''
AURA CONTROL BOX
HARDWIRE POWER HARNESS HAND HELD REMOTE MOUNTING KIT
INCLUDES
WIRE MOUNTS, SELFTAPPING
SCREWS, BOOSTER, VELCRO, ZIP TIES
ADHESIVE
BOOSTER
AURATM
ON
S+ M+
OFF
AUTO
S- M-
TM
STEP 2
STEP 1
INSTALLATION
Decide where to locate the control box
and ensure wiring has enough length for
light bars to be installed in desired
location.
Inspect the kit has all the contents included and power the unit to test the
lights function properly with the 12 volt adapter provided.
IMPORTANT:
Avoid installation areas of the engine bay
+ heated surfaces.
As shown below, connect all the LED bars to the control box.
TM
FRONT 36”
REAR 36”
RIGHT
48”
LEFT
48”
L=13 cm w / DC 12V connector
L=11 cm w / 3P-Female connector
L=300 cm w / 3P-Male connector
L=250 cm w / 3P-Female connector
L=30 cm w / 3P-Male connector
L=250 cm w / 3P-Female connector
L=30 cm w / 3P-Male connector
L=30 cm w / 3P-Male connector
L=250 cm w / 3P-Female connector
L=30 cm w / 3P-Male connector
L=250 cm w / 3P-Female connector
1
2
3
4
5
6
7
8
9
10
11
LEFTLEFT
RIGHT
RIGHT
FRONT
FRONT REARREAR
48''
48''
48''
48''
36''
36''
36''
36''
STEP 3
TM
STEP 4
Secure the light bars using the zip
ties to tie all the wiring away from
the moving components.
Secure Control box in desired location
with Velcro or zipties.
HOW TO CONNECT
POWER HARNESS TO
YOUR VEHICLE
Connect the Red line(+) of power
hareness to the vehicle battery's
positive terminal.
Connect the Black line (-) of power
hareness to the vehicle battery's
negativeterminal or an unpainted
area on your vehicle's frame.
-
-
INSTALLATION
STARTER
ENGINE
BLOCK
HARDWIRE
POWER
HARNESS
1.
2.
Connecting to more than 10 AMP will override the kit and cause early failure,
ensure it is 10AMPs or less!!
Please ensure that the LED bars or strips/control box/wiring all are mounted
in areas where will not exceed 85℃ or 185℉.
WARNING
Using the included E-Z Remote, select your
desired color or pattern.
STEP 5
OPT7 Lighting is not liable for damages or personal injuries while installing this product.
The Installation Guide is intended as assistance to reduce setup time. OPT7 Lighting
assumes no responsibility for improper installation.
If you are unfamiliar with your vehicle or inexperienced with aftermarket upgrades, please
seek professional assistance.
OPT7 recommends installation for safety and guidance.
Modied installations or installation recommendations not specied by OPT7
Lighting will void product warranty.
ON
S+ M+
OFF
AUTO
S- M-
Power-ON
Automatic Color Change
Power-OFF
Speed +/- 10Levels
Mode +/- 20 Mode
Dimmer 10 Levels
Color Selection 12 Colors
INSTALLATION
DISCLAIMER
1
2
3
4
5
6
7
-
1
-
2
-
3
-
4
w innych językach
- English: OPT7 AURA Installation guide
Powiązane dokumenty
Inne dokumenty
-
IPT Pumps 5581--96 Instrukcja obsługi
-
Sea Ray 2003 400 SEDAN BRIDGE Parts Manual
-
Audiovox Pursuit PRO 9549FT Instrukcja instalacji
-
-
-
Dometic SmartStart RV Instrukcja obsługi
-
Yamaha S12 Instrukcja obsługi
-
-
-
