Classic Exhibits VK-2918 Setup Instructions
- Typ
- Setup Instructions
www.classicexhibits.com
Step 1
Page 1 of 3
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - VK-2918 - General Layout
Plan View
Elevation View
20’
10’
www.classicexhibits.com
Step 2
Page 2 of 3
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - General Information
The Tool Typical Connection
Horizontal Inline Connection (remove only one setscrew)
Base Plate Connection Vertical Connection
(remove only two setscrews)
Most Visionary Designs exhibits can be
assembled with the supplied Hex Key Tool.
Occasionally, a flat head screwdriver may
be required.
Most horizontal extrusion connections have a patented expandable lock. This lock inserts into
the groove of an opposing extrusion. Tightening the lock with the Hex Key Tool expands the lock
and creates a strong positive connection.
Remove only (1) setscrew when disassembling. Replace setscrew in
extrusion after assembling it. Before packing, replace setscrew in
extrusion to avoid losing it.
Attach base plate to round or square
vertical extrusion using the bolt provided.
Be careful not to strip the threads.
When vertical extrusions are packed in
portable cases rather than crates or
tubs, they must broken down into
smaller sections which then require
assembly.
Remove only (2) setscrews when
disassembling. Replace setscrews in
extrusion after assembling it. Before
packing, replace setscrews in extrusion
to avoid losing them.
Using Your Setup Instructions
The Visionary Designs Setup Instructions are created specifically for your
configuration. They are laid out sequentially, including an exploded view of
the entire display, and then a logical series of detailed steps to assemble the
main structure and components. We encourage you to study the instructions
before attempting to assemble your exhibit.
Each page reminds you to tighten the setscrews after disassembling your
exhibit to prevent loss of the locks and setscrews (see below in RED).
This is VERY IMPORTANT.
Cleaning and Packing Your Display
1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only
non-abrasive cleaners.
2) When cleaning laminate inserts or countertops, use mild cleansers and a
soft material such as cotton.
3) Keep all display components away from extreme heat and long exposure
to sunlight to avoid warping and fading.
4) Retain all packing material. It will make re-packing much easier and will
reduce the likelihood of shipping damage.
Typical Connection (cont’d)
Numbered Label
Each extrusion contains a numbered label which
corresponds with setup instructions.
The label is located within a groove of the extrusion
(when possible). With Visionary Designs the labels
contain Black numbers unless otherwise specified.
Detail C E liateDD liateDDetail B
Detail A
Setscrews
www.classicexhibits.com
Step 1
Page 1 of 3
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - VK-2918 - Backwall Assembly
Steps:
1) Attach lower
vertical extrusions [2,2a,3,3a & 9] to base
plates [1,1a].
2) Attach upper verticals [4,4a,5,5a] to lower verticals as shown.
3) Attach horizontal extrusions [6a & 6b], [7a & 7b] & [8a & 8b]
together as shown.
4) Connect horizontal assemblies [6a/6b] [7a/7b] & [8a/8b] between
vertical assemblies as shown.
5) Connect horizontal extrusion [10] between verticals [2 & 9]
and [3a & 9] as shown.
6) Connect horizontals [11] between verticals [2a & 3]
inserting Wings to A-10 clamps as shown.
Item Qty Description
1/1a 2/2 Base Plate
2/2a 1/1 48” S80 Vertical Extrusion
3/3a 1/1 48” S80 Vertical Extrusion
4/4a 1/1 45.6711” Curved Vertical Extrusion
5/5a 1/1 45.6711” Curved Vertical Extrusion
6a/6b 2/2 36.062” Z45 Horizontal Extrusion
7a/7b 2/2 44.6482” Z45 Horizontal Extrusion
8a/8b 2/2 47.3183” Z45 Horizontal Extrusion
9 2 38.6145” Curved Vertical Extrusion
9a 2 Flange Plate
10 2 11.75“ Z45 Horizontal Extrusion
11 2 23.5” Z45 Horizontal Extrusion
2
9
2a
4a
3a
5a
10
11
11
9
10
6a
6b
7a
7b
8a
8b
3
4
5
1
Attach graphics
to velcro on front of
assembled backwall
Velcro
Velcro:
Front/Top Edge
Velcro:
Front/Top Edge
1a
1
6a
6b
7a
7b
8a
8b
Velcro:
Front/Top Edge
Velcro:
Front/Top Edge
Velcro
Velcro
Velcro
1a
Wing
Wing
When desired location
is found, tighten
set screw to secure.
Tighten knob to
secure shelf in place.
Slide connector on back
of A10 clamp into groove
of extrusion.
A10 Clamp Attachment
*
Screw
9a
*
Screw
9a
Counter Top Attachment
Insert screws located on underside
of counter into holes on flange plate
and secure with wing nuts.
Wing Nut
*
www.classicexhibits.com
Step 2
Page 2 of 3
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - VK-2918 - Backwall Attachments
Steps:
1) Attach lights to top of backwall as shown
.
2) Attach graphic headers to velcro on front of [8a & 8b] as shown.
3) Attach wings to A-10 clamps on side as shown.
4) Place counter tops on top of extrusion [9 & 10] as shown.
5) Attach monitor mount as shown in
Monitor Mount Attachment
detail.
When desired location
is found, tighten
set screw to secure.
Tighten knob to
secure shelf in place.
Slide connector on back
of A10 clamp into groove
of extrusion.
A10 Clamp Attachment
Wing
Counter Top
Counter Top
Wing
Wing
Graphic Header
Graphic Header
Wing
Wing
*
**
Wing
Monitor Mount Attachment
Slide connectors into groove
of extrusion. Tighten setscrew
to secure in place. Attach
monitor mount to connectors
with screws.
Connectors
Monitor
Mount
www.classicexhibits.com
Step 3
Page 3 of 3
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - VK-2918 - Pedestal Assembly
Front Aluminum portion of Pedestal Assembly
3) Attach Verticals [2 & 3] to Base Plate [1].
NOTE: Base Plate Centered and Flush with Back LT Portion of Pedestal.
4) Attach horizontals [4,5 & 6] between Verticals [2 & 3] as shown.
5) Place counter top on top of assembled pedestal as shown.
6) Attach graphic sign to Velcro on horizontal [6].
LT Pedestal Assembly
1) Assemble panels together starting with 1 in numerical order.
2) Attach Internal Shelf with provided shelf supports.
Panel Description
1 5.75”r X 38”h Quarter Curve Panel
2 19”w x 38”h Flat Panel
3 5.75”r X 38”h Quarter Curve Panel
4 5.75”r X 38”h Quarter Curve Panel
5 19”w x 38”h Flat Panel w/Door
6 5.75”r X 38”h Quarter Curve Panel
Item Description
1 Custom Base Plate
2 38”h Curved Round Vertical - Counter Support - Left side
3 38”h Curved Round Vertical - Counter Support - Right side
4 7” Lower Tapered Horizontal extrusion
5 8” Middle Tapered Horizontal extrusion
6 16.5” Upper Tapered Horizontal extrusion
Color Coded Clip
w/ assembly number
is top of panel
Panel Lock
When Required
Black Clip
is bottom of
panel
Connector
Cut Away View Of
Slide Clips
Slide Panel
down until
clips lock.
Left Hand
Grasps Panel
Firmly
With Right Hand Thumb
Close to Seam
Squeeze
Push Forward &
Lift
1
2
3
4
6
5
4
4
3
1
2
5
6
Steps 1 & 2 - LT Details:
Internal Shelf
Counter Top
Graphic Sign
www.classicexhibits.com
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - Case Packing - 1 of 3
Level 1
Wings
Counter
1&1a
10
6a
6b
8b
8a
7a
7b
Oval Graphic Header
Level 2
Top View of Each Level
Level 3 Level 4
Graphics
3 2 9 4 5
www.classicexhibits.com
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - Case Packing - 2 of 3
Counter
1&1a
10
6b
7b
7a
8b
8a
6a
11
11
Top View of Each Level
Level 1
Center Wings
Level 2 Level 3 Level 4
Graphics
2a 3a 9 4a 5a
www.classicexhibits.com
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - Case Packing - 3 of 3
Top View of Each Level
Level 1
Counter Shelf
1
Shelf Supports
Oval Graphic
6
5
4 4
3 2
4
3
5 w/ Door
Curved Panels 1 & 6
Curved Panels 3 & 4
Flat Panels 2 & 5
2
6
1
Level 2 Level 3 Level 4
Front View
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Classic Exhibits VK-2918 Setup Instructions
- Typ
- Setup Instructions
w innych językach
- English: Classic Exhibits VK-2918
Powiązane dokumenty
-
Classic Exhibits VK-2916 Setup Instructions
-
-
-
-
-
-
-
-
-