Simplicity 1696205-01 Instrukcja obsługi

Not for

Reproduction

1756268

Revision A

Single Stage Snowthrower

Briggs & Stratton Power Products Group, LLC

Milwaukee, WI USA

Operator’s Manual

Návod k obsluze

Bedienungsanleitung

Ohjekirja

Manual de l’opérateur

Felhasználói kézikönyv

Manuale dell’operatore

Vartotojo vadovas

Bruksanvisningen

Instrukcja obsługi

Руководство по эксплуатации

Návod na obsluhu

Uporabniški priročnik

Instruktions handbok

en

cs

de

fi

fr

hu

it

lt

no

pl

ru

sl

sv

sk

Not for

Reproduction

2

B

A

C

D

E

F

G

B

C

A

D

3

2

1

4

A

B

C

Not for

Reproduction

3

A

B

A

B

C

7

WEAR LIMIT

9

6

8

5

A

B

C

Not for

Reproduction

4

Products Covered by This Manual

The following products are covered by this manual:

1696205-01, 1696211-01, 1696219-01, 1696219-02, 1696225-01,

1696252-01, 1696252-02.

Table of Contents

Operator Safety ................................................................... 4

Features and Controls ........................................................ 10

Operation ........................................................................... 11

Snowthrower Safety Test .................................................. 13

Maintenance ...................................................................... 15

Storage .............................................................................. 17

Troubleshooting ................................................................. 18

Specications .................................................................... 19

NOTE: Please refer to the Customer Contact Guide and Setup

Instructions for additional information.

Safety Alert Symbol and Signal Words

The safety alert symbol is used to identify safety information

about hazards that can result in personal injury. A signal word

(DANGER, WARNING, or CAUTION) is used with the alert symbol

to indicate the likelihood and potential severity of injury. In

addition, a hazard symbol may be used to represent the type of

hazard.

DANGER indicates a hazard which, if not avoided, will

result in death or serious injury.

WARNING indicates a hazard which, if not avoided, could

result in death or serious injury.

CAUTION indicates a hazard which, if not avoided, could

result in minor or moderate injury.

NOTICE indicates an action that could result in damage to

the product.

Hazard Symbols and Meanings

Read the Operator’s Manual

Remove key before performing

maintenance

Carbon monoxide poisoning hazard

Fire hazard

Explosion hazard

Kickback hazard

Hot surface hazard

Wear safety glasses

Thrown objects hazard

Amputation hazard - rotating impeller

Amputation hazard - rotating auger

Entanglement hazard - rotating parts

Electric shock hazard

Keep safe distance away

Keep children away

Operator Safety

Not for

Reproduction

5

en

Operator Safety

WARNING

• Hand contact with the rotating impeller inside the discharge

chute is the most common cause of injury associated with

snowthrowers.

• This snowthrower is capable of amputating hands and feet,

and throwing objects. Read and observe all the safety

instructions in this manual. Failure to do so could result in

death or serious injury.

DANGER

• Whenever cleaning, repairing, or inspecting the

snowthrower, make sure the engine is OFF, spark plug wire

is disconnected, and all moving parts have stopped.

• Do not put hands or feet near or under rotating parts. Keep

clear of the discharge opening at all times.

• Never operate the snowthrower without proper guards, and

other safety devices in place and working.

• Never leave the snowthrower unattended while engine is

running. Always disengage the auger and traction controls,

stop engine, and remove keys.

• Keep all loose clothing away from the front of the

snowthrower and auger. Scarves, mittens, dangling

drawstrings, loose clothes, and pants can quickly become

caught in the rotating device and amputation will occur. Tie

up long hair and remove jewelry.

• Run the machine a few minutes after discharging snow to

prevent freeze-up of the collector/impeller.

• Disengage power to the collector/impeller when

snowthrower is transported or not in use.

Keep hands, feet, and clothing away from

rotating parts. Rotating parts can contact

or entangle hands, feet, hair, clothing, or

accessories.

Failure to observe these safety instructions

will result in traumatic amputation or severe

laceration.

WARNING

• Always wear safety glasses or eye shields during

operation, and while performing an adjustment or repair.

• Always be aware of the direction the snow is being

thrown. Nearby pedestrians, pets, or property may be

harmed by objects being thrown.

• Be aware of your environment while operating the

snowthrower. Don’t run over items such as gravel,

doormats, newspapers, toys, and rocks hidden under

snow, as they can all be thrown from the chute or jam in

the auger.

• Use extreme caution when operating on or crossing

gravel drives, walks, or roads.

• Adjust the collector housing height to clear gravel or

crushed rock surface.

• Never operate the snowthrower near glass enclosures,

automobiles, window wells, drop-offs, and the like without

proper adjustment of the discharge chute angle.

• Familiarize yourself with the area in which you plan

to operate the snowthrower. Mark off boundaries of

walkways and driveways.

Objects can be picked up by auger and thrown

from chute. Never discharge snow toward

bystanders or allow anyone in front of the

snowthrower. Failure to observe these safety

instructions will result in death or serious injury.

WARNING

• Save these original instructions for future reference.

• Be thoroughly familiar with the controls and the proper use

of the snowthrower.

• Make sure you are properly trained before operating the

snowthrower.

• Know how to stop the unit and disengage the controls

quickly.

• Never allow anyone to operate the snowthrower without

proper instruction.

• Always follow the instructions in the operator’s manual, if

the snowthrower will be stored for an extende d period.

• Maintain or replace safety and instruction labels as

necessary.

• Never attempt to make major repairs on the snowthrower

unless you have been properly trained. Improper servicing

of the snowthrower can result in hazardous operation,

equipment damage, and voiding of the product warranty.

Read, understand, and follow all the

instructions on the snowthrower and in the

operator’s manual before operating this unit.

Failure to observe the safet y instructions in this

manual could result in death or serious injury.

Discharge chute contains rotating impeller

to throw snow. Never clear or unclog the

discharge chute with your hands. Fingers can

quickly become caught in the impeller. Always

use a clean-out tool.

Failure to observe these safety instructions

will result in traumatic amputation or severe

laceration.

DANGER

Not for

Reproduction

6

Operator Safety

WARNING

• Keep children out of the area during operation. Children are

often attracted to the equipment. Be mindful of all persons

present.

• Be alert and turn unit off if children enter the area.

• Never allow children to operate the unit.

• Use extra care when approaching blind corners, shrubs,

trees, or other objects that may obscure vision. Children

may be present.

Tragic accidents can occur if the operator is

not alert to the presence of children. Children

are often attracted to the unit and the operating

activity. Never assume the children will remain

where you last saw them.

Engines give off carbon monoxide, an

odorless, colorless, poison gas. Breathing

carbon monoxide can cause nausea, fainting,

or death.

WARNING

• Start and run engine outdoors.

• Do not run the engine in an enclosed area, even if doors or

windows are open.

• Keep fuel away from sparks, open flames, pilot lights, heat,

and other ignition sources.

• Check fuel lines, cap, and fittings frequently for cracks or

leaks. Replace if necessary.

• Use an approved fuel container.

• If fuel spills, wait until it evaporates before starting engine.

When Starting Engine

• Ensure that spark plug, muffler, fuel cap, and air cleaner (if

equipped) are in place and secured.

• Do not crank the engine with the spark plug removed.

• If fuel is spilled, do not attempt to start the engine, but move

the snowthrower away from the area of the spill, and avoid

creating any source of ignition, until the fuel vapors have

dissipated.

• Do not over-prime the engine. Follow the engine starting

instructions in this manual.

• If the engine floods, set choke (if equipped) to OPEN/RUN

position, move throttle (if equipped) to FAST position and

crank until engine starts.

When Operating Equipment

• Do not tip the snowthrower at an angle which causes the

fuel to spill.

• Do not choke the carburetor to stop the engine.

• Never run the engine with the air cleaner assembly (if

equipped) or the air filter (if equipped) removed.

When Changing Oil

• If you drain the oil from the top oil fill tube, the fuel tank

must be empty or fuel can leak out and result in a fire or

explosion.

When Transporting Equipment

• Transport with fuel tank EMPTY, or with fuel shut-off valve

OFF.

When Storing Gasoline or Equipment With Fuel in Tank

• Store away from furnaces, stoves, water heaters, or other

appliances that have pilot light or other ignition source

because they can ignite fuel vapors.

WARNING

When Adding Fuel

• Turn off engine and let cool at least 2 minutes before

removing the fuel cap and adding fuel.

• Fill fuel tank outdoors or in a well ventilated area.

• Do not overfill the fuel tank. To allow for the expansion of

gasoline, do not fill above the bottom of the fuel tank neck.

Fuel and its vapors are extremely flammable

and explosive. Always handle fuel with

extreme care.

Failure to observe these safety instructions can

cause a fire or explosion which will result in

severe burns or death.

Not for

Reproduction

7

Operator Safety

en

WARNING

• Disengage all clutches and shift into neutral before starting

the engine.

• Let the engine adjust to outdoor temperatures before

starting to clear snow.

• Use a grounded three-wire plug for all snowthrowers

equipped with electric drive motors or electric starting

motors.

WARNING

• If there is natural or LP gas leakage in area, do not start

engine.

• Do not use pressurized starting fluids because vapors are

flammable.

WARNING

• Never touch a hot engine or muffler. Allow muffler, engine

cylinder, and fins to cool before touching.

• Remove debris from muffler area and cylinder area.

• Install and maintain in working order a spark arrester before

using equipment on forest-covered, grass-covered, or

brush-covered unimproved land.

• It is a violation of California Public Resource Code,

Section 4442, to use or operate the engine on any forest-

covered, brush-covered, or grass-covered land unless

the exhaust system is equipped with a spark arrester, as

defined in Section 4442, maintained in effective working

order. Other states or federal jurisdictions may have

similar laws. Contact the original equipment manufacturer,

retailer, or dealer to obtain a spark arrester designed for the

exhaust system installed on this engine.

Starting engine creates sparking.

Sparking can ignite nearby flammable gases.

Explosion and fire could result.

Running the engine produces heat. Engine

parts, especially muffler, become extremely

hot.

Failure to observe these safety instructions

could result in severe thermal burns on contact.

Safe operation of the snowthrower requires

the proper care and maintenance of the

engine.

WARNING

• When performing any maintenance or repairs on the

snowthrower, shut OFF the engine, disconnect spark plug

wire, and keep the wire away from the plug to prevent

someone from accidently starting the engine.

• Check shear bolts and other hardware at frequent intervals

for proper tightness.

• Keep nuts and bolts tight and keep snowthrower in good

condition.

• Never tamper with safety devices. Check their proper

operation regularly and make necessary repairs if they are

not functioning properly.

• Components are subject to wear, damage, and deterioration.

Frequently check components and replace with

recommended parts, when necessary.

• Check control operation frequently. Adjust and service as

required.

• Use only factory authorized replacement parts, or like, parts

when making repairs.

• Always comply with factory specifications on all settings and

adjustments.

• Use only factory authorized, or like, attachments and

accessories such as wheel weights, counterweights, or cabs.

• Never attempt to make any adjustments while the engine

is running (except when specifically recommended by the

factory).

This snowthrower must be properly

maintained to ensure safe operation and

performance. Failure to observe the safety

instructions in this manual could result in

death or serious injury.

Not for

Reproduction

8

Operator Safety

WARNING

This snowthrower is only as safe as the opera-

tor. If it is misused, or not properly maintained,

it can be dangerous. Remember you are re-

sponsible for your safety and those around you.

• Keep the area of operation clear of all persons, particularly

small children and pets.

• Thoroughly inspect the area where the snowthrower will be

used and remove all doormats, sleds, boards, wires, and

other foreign objects.

• Do not operate the snowthrower without wearing adequate

winter clothing.

• Wear footwear that will improve footing on slippery surfaces.

• Use caution to avoid slipping or falling especially when

operating the snowthrower in reverse.

• Never operate the snowthrower without good visibility or

light. Always be sure of your footing, and keep a firm hold on

the handles.

• Do not clear snow across the face of slopes. Use extreme

caution when changing direction on slopes. Do not attempt

to clear steep slopes.

• Do not overload the machine capacity by attempting to clear

snow too quickly.

• Never operate the snowthrower at high transport speeds on

slippery surfaces. Look behind the snowthrower and use

care when operating in reverse.

• Do not use the snowthrower on surfaces above ground level

such as roofs of residences, garages, porches, or other such

structures or buildings.

• Operators should evaluate their ability to operate the

snowthrower safely enough to protect themselves and

others from injury.

• The snowthrower is intended to remove snow only. Do not

use the snowthrower for any other purpose.

• Do not carry passengers.

• After striking a foreign object, shut OFF the engine,

disconnect the cord on electric motors, thoroughly inspect

the snowthrower for any damage, and repair the damage

before restarting and operating the snowthrower.

• If the snowthrower vibrates abnormally, shut OFF the

engine. Vibration is generally a warning of trouble. See an

authorized dealer if necessary for repairs.

• For models equipped with electric starting motors,

disconnect the power cord after the engine starts.

WARNING

Rapid retraction of the starter cord (kickback)

will pull your hand and arm toward the engine

faster than you can let go.

Broken bones, fractures, bruises, or sprains

could result.

When Starting the Engine

• Pull the starter cord slowly until resistance is felt and then

pull rapidly to avoid kickback.

WARNING

Damaged or ungrounded power cords could

cause electric shock.

Electric shock could cause severe burns or

death.

When Using the Electric Starter

• The power cord must be properly grounded at all times.

• Use only a three-conductor power cord properly grounded

to the power source.

• If the extension cord is damaged, it must be replaced a

qualied person to avoid a hazard.

Not for

Reproduction

9

Operator Safety

Safety Decals

Before operating the snowthrower, read and understand the

installed safety decals. The cautions and warnings are provided

to help you avoid personal injury or damage to your snowthrower.

If any safety decals become damaged or illegible, order

replacements from your local authorized service dealer.

A — Part No. 1727207 Chute Danger Decal

B — Part No. 1739967 Auger Danger Decal

C — Part No. 276925 Engine Warning Decal

1739967

A

B

C

en

Not for

Reproduction

10

Features and Controls

Snowthrower and Engine Controls

A — Auger Control / Auger

B

— Chute Control - Handle Mount (if equipped)

Chute Control - Chute Mount (if equipped)

C

— Deector Control - Trigger or Wing Knob

D

— Starter Button

E

— Starter Receptacle

F

— Starting Instructions Decal (if equipped)

G

— Starting Instructions Decal (if equipped)

H

— Headlight (if equipped)

I

— Choke Control

J — Fuel Tank and Cap

K — Oil Fill/Dipstick

L

— Primer Button

M — ON/OFF or Push/Pull Key

N — Starter Cord Handle

O — Oil Drain Plug

E

D

L

J

I

K

M

O

C

1739977

H

G

F

B

A

N

B

C

A

Control Symbols and Meanings

On / O switch

Choke closed; choke open

Push primer 2 times

Plug in extension cord

Press button to start

Engage auger control

Rotate chute control

Not for

Reproduction

11

Operation

en

Oil Recommendations

NOTICE: The engine was shipped from the factory without oil.

Before you start the engine, ensure that you add oil according to

the instructions in this manual. If you start the engine without oil, it

will be damaged beyond repair and will not be covered under the

warranty.

Use a high quality detergent oil classified for Service SG, SH,

SJ, SL, or higher. Synthetic 5W30 motor oil is acceptable for all

temperatures. DO NOT mix oil with gasoline. See chart below for

oil recommendations.

* Below 40°F (4°C) the use of SAE 30 will result in hard starting.

** Above 80°F (27°C) the use of 10W-30 may cause increased oil con-

sumption. Check oil level more frequently.

Add Oil / Check Oil Level

1. Ensure the snowthrower is level.

2. Clean the oil dipstick area of any debris.

3. See Specifications for the oil capacity.

4. Remove the oil dipstick (A, Figure 1) and wipe it with a clean

cloth.

5. Add oil slowly into the engine oil fill (B).

6. Wait one minute and then insert the oil dipstick and turn it

clockwise to tighten.

7. Remove the oil dipstick and check the oil level.

8. If necessary, add oil until the level reaches the full mark (C) on

the oil dipstick. Do not overfill.

9. Insert and tighten the oil dipstick securely.

Fuel Recommendations

Fuel must meet these requirements:

• Clean, fresh, unleaded gasoline.

• A minimum of 87 octane/87 AKI (91 RON). High altitude

use, see below.

• Gasoline with up to 10% ethanol (gasohol) is acceptable.

NOTICE: Do not use unapproved gasoline, such as E15 and

E85. Do not mix oil in gasoline or modify the engine to run on

alternate fuels. Use of unapproved fuels will damage the engine

components and void the engine warranty.

To protect the fuel system from gum formation, mix a fuel

stabilizer into the fuel. See Storage. All fuel is not the same. If

starting or performance problems occur, change fuel providers or

change brands. This engine is certified to operate on gasoline.

The emissions control system for this engine is EM (Engine

Modifications).

High Altitude

At altitudes over 5,000 feet (1524 meters), a minimum

85 octane/85 AKI (89 RON) gasoline is acceptable. Operation

without a high altitude adjustment will cause decreased

performance, increased fuel consumption, and increased

emissions. Contact a Briggs & Stratton Authorized Dealer for high

altitude adjustment information.

Operation of the engine at altitudes below 2,500 feet (762 meters)

with the high altitude adjustment is not recommended.

1. Clean the fuel cap area of dirt and debris. Remove the fuel cap

(D, Figure 1).

2. Fill the fuel tank with fuel. To allow for expansion of the fuel, do

not fill above the bottom of the fuel tank neck.

3. Install the fuel cap.

Add Fuel

WARNING

When Adding Fuel

• Turn off engine and let cool at least 2 minutes before

removing the fuel cap and adding fuel.

• Fill fuel tank outdoors or in a well ventilated area.

• Do not overfill the fuel tank. To allow for the expansion of

gasoline, do not fill above the bottom of the fuel tank neck.

• Keep fuel away from sparks, open flames, pilot lights, heat,

and other ignition sources.

• If fuel spills, wait until it evaporates before starting engine.

Fuel and its vapors are extremely flammable

and explosive. Always handle fuel with

extreme care.

Failure to observe these safety instructions can

cause a fire or explosion which will result in

severe burns or death.

Not for

Reproduction

12

Operation

Start the Engine

WARNING

When Starting Engine

• Ensure that spark plug, muffler, fuel cap, and air cleaner (if

equipped) are in place and secured.

• Do not crank the engine with the spark plug removed.

• If fuel is spilled, do not attempt to start the engine, but move

the snowthrower away from the area of the spill, and avoid

creating any source of ignition, until the fuel vapors have

dissipated.

• Do not over-prime the engine. Follow the engine starting

instructions in this manual.

• If the engine floods, set choke (if equipped) to OPEN/RUN

position, move throttle (if equipped) to FAST position and

crank until engine starts.

Fuel and its vapors are extremely flammable

and explosive. Always handle fuel with

extreme care.

Failure to observe these safety instructions can

cause a fire or explosion which will result in

severe burns or death.

WARNING

Damaged or ungrounded power cords could

cause electric shock.

Electric shock could cause severe burns or

death.

When Using the Electric Starter

• The power cord must be properly grounded at all times.

• Use only a three-conductor power cord properly grounded

to the power source.

• If the extension cord is damaged, it must be replaced a

qualied person to avoid a hazard.

NOTE: The electric starter is designed for a three-conductor

power cord only and operates on standard household current. If a

properly grounded electrical source is not available, DO NOT use

the electric starter. Contact a licensed electrician for installation of

a properly grounded system.

Engines give off carbon monoxide, an

odorless, colorless, poison gas. Breathing

carbon monoxide can cause nausea, fainting,

or death.

WARNING

• Start and run engine outdoors.

• Do not run the engine in an enclosed area, even if doors or

windows are open.

WARNING

Rapid retraction of the starter cord (kickback)

will pull your hand and arm toward the engine

faster than you can let go.

Broken bones, fractures, bruises, or sprains

could result.

When Starting the Engine

• Pull the starter cord slowly until resistance is felt and then

pull rapidly to avoid kickback.

1. Check the oil level. See Add Oil / Check Oil Level.

2. Ensure the auger control is disengaged.

3. Insert the ON/OFF key (A, Figure 2) and turn to the ON

position or insert the Push/Pull key, if equipped.

4. Turn the choke control (B) to the closed position.

NOTE: Do not close the choke control to start a warm engine.

5. Press the primer button (C) two times.

NOTE: Do not press the primer button to start a warm engine.

6. Rewind start: Firmly hold the starter cord (D). Pull the starter

cord slowly until resistance is felt, then pull rapidly.

7. Electric start: First connect the power cord (not supplied

(E, Figure 3) to the starter receptacle (F) and then into a wall

receptacle. If an additional power cord is required, ensure it is

a three-conductor cord.

8. Electric start: Press the starter button (G). After the engine

starts, disconnect the power cord from the wall receptacle first

and then from the starter receptacle.

NOTICE: To extend the life of the starter, use short starting

cycles (five seconds maximum). Wait one minute between

starting cycles.

9. As the engine warms up, move the choke control (B, Figure 2)

to the open position.

NOTE: If the engine does not start after three attempts, see

Troubleshooting.

Not for

Reproduction

13

en

Operation

WARNING

• Do not choke the carburetor to stop the engine.

Gasoline and vapors are extremely flammable

and explosive.

Fire or explosion can cause severe burns or

death.

1. Turn the ON/OFF key (A, Figure 2) to the OFF position or

remove the Push/Pull key, if equipped.

2. Keep the key in a safe place out of the reach of children. The

engine cannot be started without the key.

Stop the Engine

Operate the Snowthrower

WARNING

• Keep children out of the area during operation. Children are

often attracted to the equipment. Be mindful of all persons

present.

• Be alert and turn unit off if children enter the area.

Tragic accidents can occur if the operator is

not alert to the presence of children. Children

are often attracted to the unit and the operating

activity. Never assume the children will remain

where you last saw them.

WARNING

• Always be aware of the direction the snow if being thrown.

• Adjust the collector housing height to clear gravel or

crushed rock surface.

Ice, gravel, or other unintended objects can be

picked up by the auger and thrown from the

chute with force.

Objects thrown from the chute could cause

death, serious injury, or property damage.

DANGER

• Read and observe all the safety instructions in this

manual. Failure to do so will result in death or serious

injury.

• Never clear or unclog the discharge chute with your hands.

Fingers can quickly become caught and traumatic amputa-

tion or severe laceration will result.

• Always use a clean-out tool to clear or unclog the dis-

charge chute.

This snowthrower is capable of amputating

hands and feet, and throwing objects. Hand

contact with the rotating auger inside the

discharge chute is the most common cause of

injury associated with snowthrowers.

DANGER

• Read and observe all the safety instructions in this

manual. Failure to do so will result in death or serious

injury.

• Never clear or unclog the discharge chute with your hands.

Fingers can quickly become caught and traumatic amputa-

tion or severe laceration will result.

• Always use a clean-out tool to clear or unclog the dis-

charge chute.

This snowthrower is capable of amputating

hands and feet, and throwing objects. Hand

contact with the rotating auger inside the

discharge chute is the most common cause of

injury associated with snowthrowers.

Snowthrower Safety Test

1. Start the snowthrower and engage the auger control (C,

Figure 4, Figure 5) for several seconds.

2. Release the auger control.

3. The auger must stop within 5 seconds after the auger control

is released. If it does not:

a. Adjust the control cable.

b. If the auger still does not stop within 5 seconds, see an

Authorized Dealer.

Not for

Reproduction

14

Operation

Clearing a Clogged Discharge Chute

1. STOP THE ENGINE!

2. Ensure that the impeller blades have stopped rotating.

3. Use a clean-out tool to remove snow from the discharge

chute. Never clear a clogged discharge chute with your

hands!

DANGER

Discharge chute contains rotating impeller

to throw snow. Never clear or unclog the

discharge chute with your hands. Fingers can

quickly become caught in the impeller. Always

use a clean-out tool.

Failure to observe these safety instructions

will result in traumatic amputation or severe

laceration.

1. Start the engine and allow it to warm up several minutes. See

Start the Engine.

2. Adjust the direction of the chute and the angle of the deflector

to the desired positions. See Discharge Chute and

Deflector.

3. Pull the auger control (C, Figure 4, Figure 5) against the

handle to engage the auger.

4. When clearing snow is completed, release the auger control.

5. Allow the engine to run for one minute, then stop the engine.

See Stop the Engine.

Discharge Chute and Deector

Chute Rotation - Handle Mount (if equipped)

1. Squeeze and hold the button on the chute control handle (A,

Figure 4).

2. Push the handle forward or pull it rearward to rotate the chute.

3. Release the button to lock the chute in the desired position.

NOTICE: Do not use excessive force when trying to operate

the control.

Chute Rotation - Chute Mount (if equipped)

1. Grasp the chute control handle at the base of the chute (A,

Figure 5).

2. Turn the handle left or right to rotate the chute. A tension plate

holds the chute in the desired position.

NOTICE: Do not use the chute control handle to lift the

snowthrower.

Deflector Adjustment

1. Squeeze and hold the button on the deflector control handle

(B, Figure 4), or loosen the wing knob (B, Figure 5).

2. Move the control handle up or down to adjust the snow

discharge height and distance.

3. Release the button to lock the deflector in the desired

position, or tighten the wing knob.

Not for

Reproduction

15

en

First 5 Hours

Change oil

Before Each Use

Check engine oil level

Perform the auger safety test

After Each Use

Remove accumulated snow and slush to prevent freezing of the

controls, wheels, discharge chute, and auger

Every 25 Hours or Annually

Check snowthrower for loose hardware

Check auger control cable adjustment

Check rubber auger for wear; replace if necessary

Every 50 Hours or Annually

Change engine oil

Check condition of muer and muer guard

Annually

Replace sparkplug

Check valve clearance *

* Not required unless problems are noted with engine

performance. See an authorized service dealer for this item.

Change Oil

Used oil is a hazardous waste product and must be disposed of

properly. Do not discard with household waste. Check with your

local authorities, service center, or dealer for safe disposal or

recycling facilities.

Remove Oil

1. With engine off but still warm, remove the key and then

disconnect the sparkplug wire (A, Figure 6) and secure it away

from the sparkplug.

NOTE: To access the sparkplug wire, you must remove the

snow hood from the engine.

2. Remove the oil drain plug (B, Figure 7) and tilt the

snowthrower slightly to drain the oil into an appropriate

container.

3. After the oil has drained, install and tighten the oil drain plug.

Add Oil

1. Ensure the snowthrower is level.

2. Clean the oil dipstick area of any debris.

3. See Specifications for the oil capacity.

4. Remove the oil dipstick (A, Figure 1) and wipe it with a clean

cloth.

5. Add oil slowly into the engine oil fill (B).

6. Wait one minute and then insert the oil dipstick and turn it

clockwise to tighten.

7. Remove the oil dipstick and check the oil level.

8. If necessary, add oil until the level reaches the full mark (C) on

the oil dipstick. Do not overfill.

9. Insert and tighten the oil dipstick securely.

Maintenance

Maintenance Schedule

Not for

Reproduction

16

Auger and Scraper Bar Maintenance

Before each use, check wear limit on rubber auger and gap

between scraper bar support and ground (see Figure 9).

• If wear limit on the rubber bar is reached, the rubber bar needs

replacing. See authorized dealer.

• If scraper bar support makes contact with the ground, the

scraper bar needs replacing. See authorized dealer.

Control Cable Adjustment

WARNING

The auger must stop within 5 seconds after the auger control is

released. If it does not, adjust the control cable. See Adjust-

ment below or contact an authorized service dealer to adjust

the control cable.

Inspection

The auger should rotate only when the auger control is engaged

and must stop within 5 seconds when the auger control is

released. If the auger does not rotate or does not stop as

described, adjust the control cable or contact an authorized

service dealer to adjust the control cable.

If the drive belt has broken, contact an authorized service dealer

to replace the belt and adjust the control cable.

Adjustment

1. Stop the engine and remove the key. See Stop the Engine.

2. Lift the cable cover (A, Figure 8) to expose the adjustment

loops (B) and the cable end fitting (C).

3. Remove the end fitting from the adjustment loop and reinstall

as follows:

• If the auger rotates while the auger control is not

engaged, lengthen the control cable by installing

the end fitting in the next lowest loop (decrease belt

tension).

• If the auger does not rotate when the auger control is

engaged, shorten the control cable by installing the end

fitting in the next highest loop (increase belt tension).

NOTE: Some slack must remain in the cable when the auger

control is not engaged.

4. Lower the cable cover into place.

5. Repeat the inspection procedure above. If the auger does not

rotate or does not stop as described, contact an authorized

service dealer to have the snowthrower inspected.

Maintenance

Not for

Reproduction

17

Storage

Engine Oil

While the engine is still warm, change the engine oil. See

Maintenance.

Before Placing in Storage

1. Thoroughly clean the snowthrower.

2. Remove the sparkplug. Clean and re-gap, if necessary, or

replace the sparkplug.

3. Make sure all nuts, bolts, and screws are securely fastened.

4. Inspect moving parts for wear or damage. Replace parts as

necessary.

5. Lubricate the controls and moving parts.

6. Spray unpainted metal surfaces with a rust preventative.

7. Fold down the upper handle, if desired.

8. For indoor storage, cover the snowthrower and store it in a

dry area away from furnaces, stoves, water heaters, or other

appliances that have pilot lights or other ignition sources.

9. For outdoor storage, raise the snowthrower off the ground and

cover it with a heavy tarpaulin.

After Removing from Storage

1. Raise the upper handle and tighten the handle knobs

securely.

2. Remove the oil dipstick and check the oil level. If necessary,

add oil until the level reaches the FULL mark on the oil

dipstick. Do not overfill.

3. Fill the fuel tank with fresh fuel.

4. Ensure that all guards, shields, and covers are in place and

that all fasteners are tight.

Fuel System

Fuel can become stale when stored over 30 days. Stale fuel

causes acid and gum deposits to form in the fuel system or on

essential carburetor parts. To keep fuel fresh, use Briggs & Strat-

ton® Advanced Formula Fuel Treatment & Stabilizer, available

wherever Briggs & Stratton genuine service parts are sold.

For engines equipped with a FRESH START® fuel cap, use

Briggs & Stratton FRESH START® available in a drip concentrate

cartridge.

There is no need to drain gasoline from the engine if a fuel

stabilizer is added according to instructions. Run the engine for

2 minutes to circulate the stabilizer throughout the fuel system

before storage.

If gasoline in the engine has not been treated with a fuel stabi-

lizer, it must be drained into an approved container. Then run the

engine until it stops from lack of fuel. The use of a stabilizer in the

storage container is recommended to maintain freshness.

Storage

WARNING

When Storing Gasoline or Equipment With Fuel in Tank

• Store away from furnaces, stoves, water heaters, or other

appliances that have pilot light or other ignition source

because they can ignite fuel vapors.

Fuel and its vapors are extremely flammable

and explosive. Always handle fuel with

extreme care.

Failure to observe these safety instructions can

cause a fire or explosion which will result in

severe burns or death.

en

Not for

Reproduction

18

Troubleshooting

Problem Cause Solution

Auger does not stop when

auger control is released

Control cable requires

adjustment

Adjust the control cable. See Maintenance section or contact an

authorized service dealer to adjust the cable.

Auger does not turn when

auger control is engaged

Control cable requires

adjustment

Adjust the control cable. See Maintenance section or contact an

authorized service dealer to adjust the cable.

Chute rotation or deector

adjustment does not work

Fasteners are too tight;

handle mount control

damaged

Contact an authorized service dealer.

Chute or deflector is frozen Clear snow or ice from chute and deflector parts; place snowthrower in a

heated area until snow or ice melts.

Engine does not start Key is off or not inserted Turn key to the ON position or insert Push/Pull key.

Primer not pressed Press primer button twice before pulling starter rope.

Out of fuel Fill fuel tank with fresh fuel.

Choke open - cold engine Turn choke to closed position before pulling starter rope.

Engine flooded Turn choke to open position; pull starter rope several times until engine

starts.

No spark Connect sparkplug wire; replace sparkplug.

Water in fuel or old fuel Drain fuel tank; fill fuel tank with fresh fuel.

Cord not plugged in or circuit

breaker tripped (electric start

models)

Plug in cord or replace defective cord; reset circuit breaker.

Engine is hard to start or

runs poorly

Incorrect oil Change oil to lighter viscosity (such as 5W-30).

Sparkplug fouled, worn, or

gapped incorrectly

Clean and re-gap sparkplug; replace sparkplug. Contact an authorized

service dealer.

Choke control set incorrectly Open choke control gradually as engine warms up.

Excessive vibration Loose parts or damaged

parts

Stop snowthrower immediately. Contact an authorized service dealer.

Scraper bar does not

clean hard surface

Scraper bar worn Contact an authorized service dealer.

Snowthrower does not

discharge snow

Control cable requires

adjustment

Adjust the control cable. See Maintenance section or contact an

authorized service dealer to adjust the cable.

Drive belt worn or broken See authorized dealer to replace the belt.

Discharge chute clogged

with snow

STOP THE ENGINE! Ensure that the auger has stopped rotating. Use

a clean-out tool to remove snow from the discharge chute. Never clear

a clogged discharge chute with your hands! Refer to “Warnings” in

Operator Safety section.

Snowthrower does not

self-propel

Rubber auger is worn or

damaged

Contact an authorized service dealer.

Not for

Reproduction

19

en

Specifications

Engine Brand Briggs & Stratton

Engine Model Series Snow Series

™

Engine Type 4-Cycle

Starting System Recoil Start and Electric Start

Oil Capacity 20 oz (0,59 L)

Fuel Tank Capacity 3.0 qts (2,8 liters)

Sparkplug Gap .030 in (0,76 mm)

Sparkplug Torque 180 lb-in (20 Nm)

The spark ignition system on this snowthrower complies with Canadian standard ICES-002.

Power Ratings

The gross power rating for individual gasoline engine models is labeled in accordance with SAE (Society of Automotive Engineers)

code J1940 Small Engine Power & Torque Rating Procedure, and is rated in accordance with SAE J1995. Torque values are derived

at 2600 RPM for those engines with “rpm” called out on the label and 3060 RPM for all others; horsepower values are derived at 3600

RPM. The gross power curves can be viewed at www.BRIGGSandSTRATTON.COM. Net power values are taken with exhaust and air

cleaner installed whereas gross power values are collected without these attachments. Actual gross engine power will be higher than

net engine power and is aected by, among other things, ambient operating conditions and engine-to-engine variability. Given the wide

array of products on which engines are placed, the gasoline engine may not develop the rated gross power when used in a given piece of

power equipment. This dierence is due to a variety of factors including, but not limited to, the variety of engine components (air cleaner,

exhaust, charging, cooling, carburetor, fuel pump, etc.), application limitations, ambient operating conditions (temperature, humidity,

altitude), and engine-to-engine variability. Due to manufacturing and capacity limitations, Briggs & Stratton may substitute an engine of

higher rated power for this engine.

Not for

Reproduction

4

Výrobky, kterých se týká tento návod

Tento návod týká následujících produktů:

1696205-01, 1696211-01, 1696219-01, 1696219-02, 1696225-01,

1696252-01, 1696252-02.

Obsah

Bezpečnost obsluhy ............................................................ 4

Funkce a ovládání………..…………..…............................. ..10

Provoz ................................................................................ .11

Bezpečnostní test sněhové frézy......................................... 13

Údržba .......................................................... ..................... 15

Skladování .......................................................................... 17

Řešení problémů ............................................................... 18

Technické informace .......................................................... 19

POZNÁMKA: Další informace naleznete v Průvodci pro kontakt se

zákazníky a v Pokynech pro nastavení.

Bezpečností varovné značky a signální slova

Bezpečnostní varovný symbol Bezpečnostní upozornění

– Ukazuje bezpečnostní informace o riziku, které může vést

k poraněním. Signální slova (NEBEZPEČÍ, VAROVÁNÍ nebo

POZOR) jsou používána s varovnou značkou k upozornění na

pravděpodobnost a možnost vážnosti poškození. Značka rizika

může být navíc použita k reprezentaci typu rizika.

NEBEZPEČÍ ukazuje riziko, které, jestliže se mu

nevyvarujete, povede ke smrti nebo vážnému poranění.

VAROVÁNÍ ukazuje na riziko, které, jestliže se mu

nevyvarujete,

může vést ke smrti nebo vážnému

poranění.

POZOR ukazuje na riziko, které, jestliže se ho nevyvarujete,

může vést k malému či střednímu poranění.

UPOZORNĚNÍ ukazuje na situaci, která by mohla vést k

poškození výrobku.

Varovné značky a jejich význam

Přečtěte si Návod k obsluze

Před prováděním údržby vyndejteklíč

Riziko otravy oxidem uhelnatým

Riziko požáru

Riziko výbuchu

Riziko zpětného rázu

Riziko horkého povrchu

2 – Ochranné brýle

Nebezpečí odhazovaných předmětů

Riziko amputace - rotující lopatkový rotor

Riziko amputace - rotující šnek

Riziko zamotání - rotující části

Riziko elektrického šoku

Udržujte bezpečnou vzdálenost

Nedovolte přístup dětem

Bezpečnost obsluhy

Strona się ładuje...

Simplicity 1696205-01 Instrukcja obsługi

Niniejsza instrukcja jest również odpowiednia dla

Simplicity 1696205-01 Instrukcja obsługi

w innych językach

Powiązane artykuły

Inne dokumenty