Parkside PBS 900 A1 Operation and Safety Notes

Kategoria
Szlifierki elektryczne
Typ
Operation and Safety Notes
4
SZLIFIERKA TAŚMOWA
Wskazówki dotyczące obsługi i bezpieczeństwa
Tłumaczenie oryginalnej instrukcji obsługi
TRAČNI BRUSILNIK
Navodila za upravljanje in varnostna opozorila
Prevod originalnega navodila za uporabo
PÁSOVÁ BRUSKA
Pokyny pro obsluhu a bezpečnostní pokyny
eklad originálního provozního návodu
PÁSOVÁ BRÚSKA
Pokyny pre obsluhu a bezpečnostné pokyny
Preklad originálneho návodu na obsluhu
BEL T SANDER
Operation and Safety Notes
Translation of original operation manual
SZALAGCSISZOLÓ
Kezelési és biztonsági utalások
Az originál használati utasítás fordítása
BANDSCHLEIFER
Bedienungs- und Sicherheitshinweise
Originalbetriebsanleitung
BELT SANDER PBS 900 A1
GB Operation and Safety Notes Page 5
PL Wskazówki dotyczące obsługi i bezpieczeństwa Strona 15
HU Kezelési és biztonsági utalások Oldal 27
SI Navodila za upravljanje in varnostna opozorila Stran 37
CZ Pokyny pro obsluhu a bezpečnostní pokyny Strana 49
SK Pokyny pre obsluhu a bezpečnostné pokyny Strana 59
DE / AT / CH Bedienungs- und Sicherheitshinweise Seite 69
Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of the
device.
Przed przeczytaniem proszę rozłożyć stronę z ilustracjami, a następnie proszę zapoznać się z wszystkimi
funk cjami urządzenia.
Olvasás előtt kattintson az ábrát tartalmazó oldalra és végezetül ismerje meg a készülék mindegyik
funk cióját.
Pred branjem odprite stran s slikami in se nato seznanite z vsemi funkcijami naprave.
Před čtením si otevřete stranu s obrázky a potom se seznamte se všemi funkcemi přístroje.
Pred čítaním si odklopte stranu s obrázkami a potom sa oboznámte so všetkými funkciami prístroja.
Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen
Funktionen des Gerätes vertraut.
BELT SANDER PBS 900 A1
a b C
D e F
12
13
14
14
16
15
9
6
10 11
6
1
4
7 8
5
2
3
5 GB
Table of contents
Introduction
Proper use ........................................................................................................................ Page 6
Features and equipment ................................................................................................. Page 6
Included items ................................................................................................................. Page 6
Technical information ...................................................................................................... Page 7
General safety advice for electrical power tools
1. Workplace safety ....................................................................................................... Page 7
2.
Electrical safety ........................................................................................................... Page 7
3. Personal safety ............................................................................................................ Page 8
4.
Careful handling and use of electrical power tools ................................................. Page 8
Safety advice for belt sanders ........................................................................................ Page 9
Preparing for use
Tensioning / changing the sanding belt ......................................................................... Page 10
Advice on use .................................................................................................................. Page 10
Vacuum dust extraction .................................................................................................. Page 10
Operation
Switching on and off ....................................................................................................... Page 11
Selecting the correct rotational speed and sanding belt .............................................. Page 11
Using the sander in a fixed mounting ............................................................................ Page 12
Tips and tricks .................................................................................................................. Page 12
Maintenance and cleaning ........................................................................... Page 13
Service centre ......................................................................................................... Page 13
Warranty ..................................................................................................................... Page 13
Disposal ........................................................................................................................ Page 13
Declaration of Conformity / Manufacturer.................................... Page 14
6 GB
Introduction / General safety advice for electrical power tools
Introduction
Belt sander PBS 900 A1
Q
Introduction
Please make sure you familiarise your-
self fully with the way the device works
before you use it for the first time and
that you understand how to handle electrical power
tools correctly. To help you do this please read the
accompanying operating instructions. Keep these
instructions in a safe place. If you pass the device on
to anyone else, please ensure that you also pass on
all the documentation.
Q
Proper use
The belt sander is designed for dry sanding of large
surfaces of wood, plastic, metal, plaster and painted
surfaces. The device may only be used for dry sand-
ing. Always use a sanding belt and grade of grit
suitable for the particular surface you are sanding.
The speed selected should also be appropriate for
the material. The device is not intended for commer-
cial use. Any other use or modification to the device
shall be considered as improper use and could give
rise to considerable dangers. The manufacturer will
not accept liability for loss or damage arising from
improper use.
Q
Features and equipment
1
Belt speed adjuster wheel
2
Locking knob
3
ON / OFF switch
4
Toothed belt cover
5
Dust extraction spout
6
Belt adjuster screw
7
Auxiliary handle
8
Ventilation slots
9
Tensioning lever
10
Dust collection box
11
Extraction adapter
Fixed mounting kit:
12
Mounting frame
13
Clamp plates 2 x
14
Screw clamps 2 x
15
Spacer plates 2 x
16
Screw
Q
Included items
Check that all the items and accessories
are present immediately after unpacking
the device:
1 Belt sander PBS 900 A1
1 Sanding belt
The following pictograms are used in these operating instructions / on the device:
Read instruction manual!
W
Watts (Effective power)
Observe caution and safety notes! Safety class II
Caution – electric shock!
Danger to life!
Wear hearing protection, dust
protection mask, protective glasses
and protective gloves.
Explosive material!
Keep children away from electrical
power tools!
n
0
Rated idle running speed
Risk of loss of life by electric shock from
damaged mains lead or mains plug!
V
~
Voltage
Dispose packaging and appliance in
an environmentally-friendly way!
7 GB
Introduction / General safety advice for electrical power tools
Introduction
1 Dust collection box
1 Extraction adapter
(for external vacuum dust extraction)
1 Fixed mounting kit
1 Operating instructions
Q
Technical information
Belt sander: Parkside PBS 900 A1
Nominal voltage: 230 V∼, 50 Hz
Nom. power input: 900 W
No-load belt speed: 180–340 m / min
No-load speed: n
0
345–645 U / min
Sanding belt 75 x 533 mm
Protection class:
Noise and vibration data:
Measured values for noise are determined in accor-
dance with EN 60745. The A-weighted noise level
of the electrical power tool are typically:
Sound pressure level: 87 dB(A)
Sound power level: 98 dB(A)
Uncertainty K: 3 dB
Wear ear protection!
Total vibration, EN 60745:
Vibration emission value a
h
= 5.11 m / s
2
Uncertainty K = 1.5 m / s
2
The vibration level given in these
instructions has been measured in accordance with
a standardised measurement procedure specified
in EN 60745 and can be used to compare devices.
Different uses of the device give rise to different vibra-
tion levels and in many cases they may exceed the
values given in these instructions. It is easy to underes-
timate the vibration load if the electrical power tool is
used regularly in particular circumstances.
Note: If you wish to make an accurate assessment
of the vibration loads experienced during a particul
ar
period of working, you should also take into account
the intervening periods of time when the device is
switched off or is running but is not actually in use.
This can result in a much lower vibration load over
the whole of the period of working.
The PBS 900 A1 belt sander has full-wave electron-
ics with additional control electronics, soft start with
inrush current limiting.
General safety advice for
electrical power tools
Read all the safety advice
and instructions! Failure to observe the safety
advice and instructions may result in electric shock,
fire and / or serious injury.
Keep all the safety advice and instructions
in a safe place for future reference!
The term “electrical tool” used in the safety advice re-
fers to electrical tools powered by mains electricity
(by means of a mains lead) and electrical tools pow-
ered by rechargeable batteries (without a mains
lead).
1.
Workplace safety
a) Keep your working area clean and
well lit. Untidy or poorly lit working areas
can lead to accidents.
b)
Do not work with the device
in potentially explosive envi-
ronments in which there are
inflammable liquids, gases or dusts.
Electrical power tools create sparks, which can
ignite dusts or fumes.
c)
K
eep children and other people
away while you are operating
the electrical tool. Distractions
can cause you to lose control of the device.
2.
Electrical safety
a)
The mains plug on the device must match
the mains socket. The plug must not be
modified in any way. Do not use an
adapter plug with devices fitted with
8 GB
General safety advice for electrical power tools
General safety advice for electrical power tools
a protective earth. Unmodified plugs and
matching sockets reduce the risk of electric shock.
b) Avoid touching earthed surfaces such
as pipes, radiators, ovens and refrig-
erators with any part of your body.
There is an increased risk of electric shock if
your body is earthed
.
c) Keep the device away from rain or
moisture. Water entering an electrical device
increases the risk of electric shock.
d)
Do not use the mains lead for
any purpose for which it was
not intended, e.g. to carry the
device, to hang up the device or to pull
the mains plug out of the mains socket.
Keep the mains lead away from heat,
oil, sharp edges or moving parts of the
device. Damaged or tangled mains leads
increase the risk of electric shock.
e) When working outdoors with an elec-
trical power tool always use extension
cables that are also approved for use
outdoors. The use of an extension cable suita
ble
for outdoor use reduces the risk of electric shock.
f) Use a residual current device (RCD)
for protection if operating the electri-
cal power tool in a moist environment
is unavoidable. The use of an RCD reduces
the risk of electric shock.
3. Personal safety
a) Remain alert at all times, watch what
you are doing and always proceed
with caution. Do not use the device if
you are tired or under the influence of
drugs, alcohol or medication. One mo
ment
of carelessness when using the device can lead
to serious injury.
b)
Wear personal protective
equipment and always wear
safety glasses. The wearing of
personal protective equipment such as dust
masks, non-slip safety shoes, safety helmets or
ear protectors, appropriate to the type of elec-
trical power tool used and work undertaken,
reduces the risk of injury.
c) Avoid unintentional operation of the
device. Check that the electrical power
tool is switched off before you connect
it to the mains, pick it up or carry it.
Accidents can happen if you carry the device
with your finger on the ON / OFF switch or with
the device switched on.
d) Remove any setting tools or spanners
before you switch the device on. A tool
or spanner left attached to a rotating part of a
device can lead to injury.
e) Avoid placing your body in an unnat-
ural position. Keep proper footing
and balance at all times. By doing this
you will be in a better position to control the
device in unforeseen circumstances.
f) Wear suitable clothing. Do not wear
loose clothing or jewellery. Keep your
hair, clothing and gloves clear of mov-
ing parts. Loose clothing, jewellery or long
hair can become trapped in moving parts.
g) If vacuum dust extraction and collection
devices are fitted do not forget to
check
that they are properly connected and
correctly used. The use of these devices
reduces the hazard presented by dust.
4.
Careful handling and use
of electrical power tools
a) Do not overload the device. Always
use an electrical power tool that is
intended for the task you are under-
taking. By using the right electrical power
tool for the job you will work more safely and
achieve a better result.
b) Do not use an electrical power tool if
its switch is defective. An electrical power
tool that can no longer be switched on and off
is dangerous and must be repaired.
c) Pull the mains plug from the socket
before you make any adjustments to
the device, change accessories or when
the device is put away. This precaution is
intended to prevent you from unintentionally
starting the device.
9 GB
General safety advice for electrical power tools
General safety advice for electrical power tools
d) When not in use always ensure that
electrical power tools are kept out of
reach of children. Do not let anyone use
the device if he or she is not familiar
with it or has not read the instructions
and advice. Electrical power tools are dan-
gerous when they are used by inexperienced
people.
e) Look after the device carefully. Check
that moving parts are working prop-
erly and move freely. Check for any
parts that are broken or damaged
enough to detrimentally affect the
functioning of the device. Have dam-
aged parts repaired before you use
the device. Many accidents have their origins
in poorly maintained electrical power tools.
f) Keep cutting tools clean and sharp.
Carefully maintained cutting tools with sharp
cutting edges are less likely to jam and are
easier to control.
g) Use the electrical power tool, accesso-
ries, inserted tools etc. in accordance
with these instructions and advice, and
the stipulations drawn up for this par-
ticular type of device. In doing this, take
into account the working conditions
and the task in hand. The use of electrical
power tools for purposes other than those in-
tended can lead to dangerous situations.
Safety advice for
belt sanders
Hold the device by the insulated han-
dle surfaces as the sanding belt could
strike the device’s own mains lead.
Damaging a live wire could result in the metal
parts of the device also becoming live and
could lead to an electric shock.
DANGER OF FIRE FROM FLYING
SPARKS!
Sanding metal creates flying sparks. For this
reason, always make sure that nobody is placed
in any danger and that there are no inflamma
ble
materials near the working area.
When undertaking prolonged sanding of wood,
and in particular when working on materials
that give rise to dusts that are hazardous to
health, the sander must be connected to a
suitable external dust extraction device.
Ensure that there is adequate ventilation when
working on plastic, paint, varnish etc.
The belt sander is designed for the dry sanding
of large surfaces of wood, plastic, metal and
plaster and painted surfaces. The device is to
be used for dry sanding only.
Do not sand materials containing asbestos.
Asbestos is a known carcinogen.
POISONOUS DUSTS!
Sanding paints containing lead, some types of
wood and metal for example may give rise to
hazardous or poisonous dusts and represents a
risk to the health of the person operating the
device and to anyone near the work area.
Wear safety glasses and a dust
protection mask!
Securely support the workpiece. Use clamps or
a vice to grip the workpiece firmly. This is much
safer than holding it with your hand.
Never support yourself by placing your hands
near or in front of the device or the workpiece
surface. A slip can result in injury.
If a dangerous situation arises, pull the mains
plug immediately out of the mains socket.
Always work with the mains lead leading
away from the rear of the device.
Avoid contact with the moving sanding belt.
Do not work on moistened materials or damp
surfaces.
Always switch on the device before placing it
against the workpiece. After sanding, lift the de-
vice from the workpiece before switching it off.
When working always hold the device securely
with both hands (see Fig. D). Always keep
proper footing and balance.
Switch the device off and allow it to come to
a complete standstill before you put it down.
When taking a break from your work, before
carrying out any tasks on the device itself (e.g.
changing the sanding belt) and when you are
not using the device, always pull the mains
plug out of the mains socket.
10 GB
Preparing for use / Operation
Preparing for use
Q
Preparing for use
Q
Tensioning / changing
the sanding belt
RISK OF INJURY! Before
you carry out any work on the belt sander always
pull the plug out of the mains socket.
1. Then release the tensioner for the sanding belt
by moving the tensioning lever
9
fully out-
wards (see fig. A). The tensioner is now open
and the sanding belt can be removed.
2. Next insert a new sanding belt or change the
belt for one suitable for a different material or
one with a different grit size.
IMPORTANT: The direction of the arrows on
the inside of the sanding belt must agree with
that on sander housing.
3. Press the tensioning lever
9
back into its
initial position.
Adjusting the sanding belt:
Pick up the device, switch it on and turn it over.
Adjust the belt tracking by turning the adjuster
screw
6
until the edge of the sanding belt is
flush with and runs parallel to the edge of the
device (Fig. B.).
IMPORTANT: Always make sure that the
sanding belt does not cut into the housing.
Check the sanding belt regularly and if neces-
sary re-adjust it using the adjuster screw
6
.
Q
Advice on use
Light sanding pressure is enough:
Apply light sanding pressure only. The weight
of the belt sander alone is adequate to pro-
duce good sanding results. By adopting this
approach you will also prolong the life of your
sanding belts and obtain a smoother work-
piece surface.
Sanding and surfaces:
The sanding output and the quality of the surface
finish obtained are determined by the belt speed
and the grade of grit on the sanding belt (see the
section on “Selecting the correct rotational speed
and sanding belt”).
Sanding procedure:
With the sander switched on, bring it into con-
tact with the workpiece and move it forward
carefully. Work in parallel and overlapping
widths. Always work in the direction of the grain
to avoid undesirable transverse sanding marks.
After sanding always lift the device from the
workpiece before switching it off.
Q
Vacuum dust extraction
DANGER OF FIRE! There is
the danger of fire when working with electrical de-
vices that have a dustbox or can be connected to a
vacuum cleaner. Under certain conditions the
wood dust in the dust collection box (or in the vacu-
um‘s dust bag) may self-ignite, e.g. as a result of
flying sparks generated when abrading metals or
metal objects left in wood. This can happen partic-
ularly if the wood dust is mixed with paint residue
or other chemicals and the abraded particles are
hot from prolonged abrasion. Therefore you must
empty the device’s dust collection box and the vac-
uum cleaner’s dust bag before taking a break or
stopping work and always avoid overheating of the
abraded particles and the device.
Wear a dust mask!
Dust extraction using the dust
collection box:
Slide the dust collection box
10
on to the dust
extraction spout
5
on the side of the device
(Fig. C).
Emptying the dust collection box:
Pull the dust collection box
10
off the dust
extraction spout
5
. Open the dust collection
box
10
and empty it.
11 GB
Preparing for use / Operation
Preparing for use
Dust extraction using external vacuum
extraction:
If there is an explosive mixture
of dust and air you must use a vacuum device espe-
cially intended for that purpose.
DANGER OF FIRE! Do not use vacuum dust
extraction (dust collection box or vacuum cleaner)
when sanding metals (flying sparks).
1. Push the extraction adapter
11
on to the dust
extraction spout
5
on the side of the device
(see Fig. C).
2. Slide the hose of a suitable dust extraction de-
vice approved for that purpose (e.g. a workshop
vacuum cleaner) on to the extraction adapter
11
.
Q
Operation
Q
Switching on and off
The PBS 900 A1 belt sander has full-wave electronics
with additional control electronics, soft start with
inrush current limiting.
When operating the belt sander you can select
between intermittent or continuous operation mode.
For short sanding tasks use the intermittent operation
mode. For longer sanding tasks we recommend the
continuous operation mode. Whilst working in your
selected mode the device functions as follows:
To switch on intermittent operation mode:
Press the ON / OFF switch
3
.
To switch off intermittent operation mode:
Release the ON / OFF switch
3
.
To switch on continuous operation mode:
Press the ON / OFF switch
3
, and keep it
pressed, then press the locking knob
2
.
To switch off continuous operation mode:
Press and then release the ON / OFF switch
3
.
Q
Selecting the correct rotational
speed and sanding belt
You can select the belt speed using the belt speed
adjuster wheel
1
even whilst the sander is running.
The optimum belt speed depends on the workpiece
and the workpiece material. Always confirm the
best speed by carrying out a small test. The follow-
ing table lists some recommended values to help
you determine the optimum speed.
Material / type of
work
Softwood
Coarse finish
(Grit grade)
60
Fine finish (Grit grade) 240
Preselected rotation
speed
high (5-6)
Material / type of
work
Hardwood
Coarse finish
(Grit grade)
60
Fine finish (Grit grade) 180
Preselected rotation
speed
high (5-6)
Material / type of
work
Chipboard
Coarse finish
(Grit grade)
60
Fine finish (Grit grade) 150
Preselected rotation
speed
high (5-6)
12 GB
Operation
Material / type of
work
Removing paint /
varnish
Coarse finish
(Grit grade)
60
Fine finish (Grit grade) ––
Preselected rotation
speed
high (5-6)
Material / type of
work
Sanding varnish
Coarse finish
(Grit grade)
150
Fine finish (Grit grade) 320
Preselected rotation
speed
low (1-2)
Material / type of
work
Rust removal
Coarse finish
(Grit grade)
40
Fine finish (Grit grade) 120
Preselected rotation
speed
medium / high (3-4)
Material / type of
work
Plastic
Coarse finish
(Grit grade)
120
Fine finish (Grit grade) 240
Preselected rotation
speed
low / medium (2-3)
Material / type of
work
Non-ferrous metals
(e.g. aluminium)
Coarse finish
(Grit grade)
80
Fine finish (Grit grade) 150
Preselected rotation
speed
medium / high (3-4)
Q
Using the sander in
a fixed mounting
The fixed mounting kit allows you to use the device
for sanding vertically or horizontally by fastening
it on to a flat stable surface (e.g. workbench).
Sanding horizontally (see Fig. E):
Place the belt sander on to the mounting frame
12
and guide the dust extraction spout
5
through the opening of the mounting frame
12
.
Tighten the screws
16
.
Place the two clamp plates
13
on to the holes
provided on the opposite side and screw the
clamp plates tight with the provided screws.
Insert the pins of the screw clamps
14
into the
holes on one of the long sides of the mounting
frame
12
(see Fig. E). Attach the mounting
frame
12
by tightening the screw clamps
14
.
Sanding vertically (see Fig. F):
Insert the pins of the screw clamps
14
into the
holes on one of the short sides of the mounting
frame
12
. Attach the mounting frame
12
to a
flat, stable surface (e.g. workbench) by tighten-
ing the screw clamps
14
.
Place the belt sander on to the mounting frame
12
and guide the dust extraction spout
5
through
the opening of the mounting frame
12
. Tighten
the screws
16
.
Place the two clamp plates
13
on to the holes
provided on the opposite side and screw the
clamp plates tight with the provided screws.
Q
Tips and tricks
Never use the same sanding belt to sand wood
and metal.
Worn or ripped sanding belts can damage
the workpiece. Change sanding belts at the
appropriate time.
Keep the sanding belt properly tensioned so
that it does not hang down too much and
become unusable due to nicks, creases etc.
Maintenance and cleaning / Service centre / Warranty / Disposal
13 GB
Operation
Q
Maintenance and cleaning
RISK OF INJURY! Before
you carry out any work on the belt sander always
pull the mains plug out of the mains socket.
The belt sander is designed to be maintenance-free.
Clean the device frequently. This should be done
immediately after you have finished using it.
Use a dry cloth to clean the device - never use
petrol, solvents or cleaners that attack plastic.
Always keep the ventilation slots clear.
Remove any adhering dust with a narrow
paint brush.
Q
Service centre
Have your device
repaired only by qualified specialist
personnel using original manufacturer
parts only. This will ensure that your device
remains safe to use.
If the plug or mains
lead needs to be replaced, always ha
ve
the replacement carried out by the
manufacturer or its service centre. This
will ensure that your device remains safe to use.
Q
Warranty
The warranty for this appliance is for 3 year
s
from the date of purchase. The appliance
has been manufactured with care and
meticulously examined before delivery.
Please retain your receipt as proof of pur-
chase. In the event of a warranty claim,
please make contact by telephone with
our Service Department. Only in this way
can a post-free despatch for your goods
be assured.
The warranty covers only claims for material and
maufacturing defects, but not for transport damage,
for wearing parts or for damage to fragile components,
e.g. buttons or batteries. This product is for private use
only and is not intended for commercial use.
The warranty is void in the case of abusive and
improper handling, use of force and internal tam-
pering not carried out by our authorized service
branch. Your statutory rights are not restricted in
any way by this warranty.
The warranty period will not be extended by repairs
made unter warranty. This applies also to replaced
and repaired parts. Any damage and defects extant
on purchase must be reported immediately after
unpacking the appliance, at the latest, two days after
the purchase date. Repairs made after the expiration
of the warranty period are subject to payment.
GB
Service Great Britain
Tel.: 0871 5000 720
(0,10 GBP/Min.)
IAN 68917
Q
Disposal
The packaging is wholly composed of
environmentally-friendly materials that can
be disposed of at a local recycling centre.
Do not dispose of electric tools
in the household waste!
In accordance with European Directive 2002 / 96 / EC
(covering waste electrical and electronic equipment)
and its transposition into national legislation, worn out
electrical power tools must be collected separately
and taken for environmentally compatible recycling.
Contact your local refuse disposal authority for more
details of how to dispose of your worn out electrical
devices.
Maintenance and cleaning / Service centre / Warranty / Disposal
14 GB
Q
Declaration of Conformity /
Manufacturer
We, Kompernaß GmbH, the person responsible for
documents: Mr Semi Uguzlu, Burgstr. 21, D-44867
Bochum, Germany, hereby declare that this product
complies with the following standards, normative
documents and EU directives:
Machinery Directive
(2006 / 42 / EC)
EU Low Voltage Directive
(2006 / 95 / EC)
Electromagnetic Compatibility
(2004 / 108 / EC)
Applicable harmonized standards
EN 60745-1:2009
EN 60745-2-4:2009
EN 55014-1:2006+A1
EN 55014-2:1997+A1+A2
EN 61000-3-2:2006+A1+A2
EN 61000-3-3:2008
Type / Device description:
Belt sander PBS 900 A1
Date of manufacture (DOM): 08–2011
Serial number: IAN 68917
Bochum, 31.08.2011
Semi Uguzlu
- Quality Manager -
We reserve the right to make technical modifica-
tions in the course of further development.
Declaration of conformity / Manufacturer
15 PL
Spis zawartośc
Declaration of conformity / Manufacturer
Wstęp
Użytkowanie zgodnie z przeznaczeniem ...................................................................Strona 16
Wyposażenie ................................................................................................................Strona 16
Zakres dostawy .............................................................................................................Strona 17
Dane techniczne ...........................................................................................................Strona 17
Ogólne wskazówki bezpieczeństwa dla
elektronarzędzi ...................................................................................................Strona 17
1.
Bezpieczeństwo miejsca pracy ................................................................................ Strona 18
2.
Bezpieczeństwo elektryczne ....................................................................................Strona 18
3. Bezpieczeństwo osób ..............................................................................................Strona 18
4.
Staranne obchodzenie się i użytkowanie narzędzi elektrycznych........................Strona 19
Wskazówki dotyczące bezpieczeństwa dla szlifierki taśmowej ...............................Strona 19
Uruchomienie
Zamocowanie / wymiana taśmy szlifierskiej ...............................................................Strona 20
Wskazówki robocze ..................................................................................................... Strona 21
Odsysanie pyłu .............................................................................................................Strona 21
Obsługa
Załączanie i wyłączanie ..............................................................................................Strona 21
Wybór obrotów i taśmy szlifierskiej ............................................................................. Strona 22
Praca stacjonarna .........................................................................................................Strona 23
Dobre rady i triki ...........................................................................................................Strona 23
Konserwacja i czyszczenie.........................................................................Strona 23
Serwis ..........................................................................................................................Strona 23
Gwarancja ...............................................................................................................Strona 24
Utylizacja ..................................................................................................................Strona 24
Deklaracja zgodności / Producent .......................................................Strona 25
16 PL
Wstęp / Ogólne wskazówki bezpieczeństwa dla elektronarzędzi
Wstęp
Szlifierka taśmowa PBS 900 A1
Q
Wstęp
Przed pierwszym uruchomieniem należy
zapoznać się z działaniem urządzenia i
nauczyć się właściwego obchodzenia
się z elektronarzędziami. W tym celu należy prze-
czytać poniższą instrukcję. Instrukcję należy staran-
nie przechowywać. W razie przekazania urządzenia
osobom trzecim należy dać również niniejszą in-
strukcję obsługi.
Q
Użytkowanie zgodnie
z przeznaczeniem
Szlifierka taśmowa jest zaprojektowana do szlifo-
wania na sucho powierzchni drewna, tworzywa
sztucznego, metalu i masy szpachlowej oraz
powierzchni lakierowanych. Urządzenia wolno
używać wyłącznie do szlifowania na sucho. Zwróć
uwagę na to, żeby do obróbki różnych materiałów
stosować odpowiednie arkusze szlifierskie o zróż-
nicowanej ziarnistości, a także na to, żeby również
dopasować obroty do materiału. Urządzenie nie
jest przewidziane do celów zarobkowych. Każde
inne zastosowanie maszyny lub przeprowadzenie
w niej zmian jest uznawane za niezgodne z prze-
znaczeniem i kryje w sobie poważne zagrożenie
nieszczęśliwym wypadkiem. Za szkody powstałe
wskutek sprzecznego z przeznaczeniem użytkowa-
nia producent nie ponosi żadnej odpowiedzialności.
Q
Wyposażenie
1
Kółko do nastawiania prędkości taśmy
2
Przycisk ustalający
3
WŁĄCZNIK / WYŁĄCZNIK
4
Pokrywa paska zębatego
5
Króciec odsysający
6
Śruba do regulacji przebiegu taśmy
7
Dodatkowy uchwyt
8
Szczeliny wentylacyjne
9
Dźwignia mocująca
10
Pojemnik na pył
11
Adapter odsysający
Zestaw do montażu stacjonarnego:
12
Rama montażowa
13
Płytki zaciskowe 2 x
14
Ściski 2 x
W niniejszej instrukcji obsługi urządzenia zastosowano następujące piktogramy:
Przeczytaj instrukcję obsługi!
W
Watt (Moc skuteczna)
Przestrzegaj wskazówek
ostrzegawczych i bezpieczeństwa!
Klasa bezpieczeństwa II
Ostrzeżenie przed porażeniem prądem
elektrycznym! Zagrożenie dla życia!
Zakładać okulary ochronne, ochronni-
ki słuchu, maskę przeciwpyłową i ręka-
wice ochronne.
Niebezpieczeństwo wybuchu!
Dzieci trzymać z daleka od narzędzia
elektrycznego!
n
0
Projektowe obroty biegu jałowego
Niebezpieczeństwo utraty życia
wskutek porażenia prądem elektrycz-
nym w przypadku uszkodzonego
kabla sieciowego lub uszkodzonej
wtyczki sieciowej!
V
~
Volt (Napięcie przemienne)
Opakowanie i urządzenie przek
do utylizacji zgodnie z przepisami
o ochronie środowiska!
17 PL
Wstęp / Ogólne wskazówki bezpieczeństwa dla elektronarzędzi
Wstęp
15
Płytki dystansowe 2 x
16
Śruba
Q
Zakres dostawy
Bezpośrednio po rozpakowaniu urządze-
nia należy sprawdzić zakres dostawy:
1 Szlifierka taśmowa PBS 900 A1
1 Taśma szlifierska
1 Pojemnik na pył
1 Adapter odsysający (do zewnętrznego
odsysania pyłu)
1 Zestaw do montażu stacjonarnego
1 Instrukcja obsługi
Q
Dane techniczne
Szlifierka taśmowa:
Parkside PBS 900 A1
Napięcie znamionowe: 230 V∼, 50 Hz
Pobór mocy znamionowy: 900 W
Bieg jałowy-Prędkość taśmy
: 180–340 m / min
Obroty na biegu jałowym: n
0
345–645 U / min
Taśma szlifierska: 75 x 533 mm
Klasa ochrony:
Informacje dotyczące hałasu i wibracji:
Wartość pomiarowa hałasu wyznaczona zgodnie
z EN 60745. Poziom hałasu elektronarzędzia wg
oceny A wynosi typowo:
Poziom ciśnienia hałasu: 87 dB(A)
Pozom mocy hałasu: 98 dB(A)
Niepewność pomiaru K: 3 dB
Zakładać ochronniki słuchu!
Wartości całkowite drgań, EN 60745:
Wartość emisji drgań a
h
= 5,11 m / s
2
Niepewność K = 1,5 m / s
2
Podany w niniejszych instruk-
cjach poziom drgań wyznaczony został za pomo
metody pomiarowej określonej w normie EN 60745
i może zostać użyty do porównania urządzeń.
Poziom wibracji będzie się różnił w zależności od
zastosowania elektronarzędzia i w niektórych
przypadkach może przekroczyć wartość podaną
w niniejszej instrukcji. Obciążenie drganiami może
być mniej uciążliwe, jeśli elektronarzędzie będzie
regularnie trzymane w ten sposób.
Wskazówka: Celem dokładnego oszacowania
obciążenia wibracjami w okresie określonego
okresu czasu pracy należy uwzględnić również te
okresy, w których urządzenie jest wyłączone lub
wprawdzie jest włączone, ale w rzeczywistości nie
pracuje. Może to przyczynić się do znacznej redukcji
obciążenia wibracjami w całym okresie czasu pracy.
Szlifierka taśmowa PBS 900 A1 posiada pełnofa-
lowy układ regulacji prędkości z dodatkowym elek-
tronicznym układem regulacji, systemem łagodnego
rozruchu i ograniczeniem prądu załączania.
Ogólne wskazówki
bezpieczeństwa dla
elektronarzędzi
Przeczytaj wszystkie
wskazówki dotyczące bezpieczeństwa
oraz instrukcje! Zaniedbania w przestrzeganiu
wskazówek dotyczących bezpieczeństwa oraz w
przestrzeganiu instrukcji mogą spowodować pora-
żenie prądem elektrycznym, pożar i / lub ciężkie
obrażenia ciała.
Przechowuj na przyszłość wszystkie
wskazówki dotyczące bezpieczeństwa
oraz instrukcje!
Używany we wskazówkach dotyczących bezpie-
czeństwa termin „narzędzie elektryczne“ odnosi s
do narzędzi elektrycznych zasilanych z sieci (z ka-
blem sieciowym) oraz do narzędzi elektrycznych
zasilanych
z akumulatorów (bez kabla sieciowego).
18 PL
Ogólne wskazówki bezpieczeństwa dla elektronarzędzi
Ogólne wskazówki bezpieczeństwa dla elektronarzędzi
1.
Bezpieczeństwo miejsca pracy
a) Utrzymywać stanowisko pracy w czy-
stości i dobrze oświetlone. Nieporządek
i nieoświetlone obszary robocze mogą prowa-
dzić do wypadków.
b)
Nie pracuj przy użyciu urzą-
dzenia w otoczeniu zagrożo-
nym eksplozją, w którym
znajdują się palne ciecze, gazy lub
pyły. Urządzenia elektryczne wytwarzają
iskry, które mogą zapalić pył lub pary.
c)
Podczas użytkowania urzą-
dzenia elektrycznego trzymaj
dzieci i inne osoby z daleka
od urządzenia. Przy odchyleniu możesz
stracić kontrolę nad urządzeniem.
2.
Bezpieczeństwo elektryczne
a) Wtyk sieciowy urządzenia musi
pasować do wtykowego gniazdka
sieciowego. W żaden sposób nie wol-
no zmieniać wtyku sieciowego urzą-
dzenia. Nie używaj żadnych wtyków
adapterowych razem z urządzeniami
wyposażonymi w uziemienie ochron
ne.
Niezmienione wtyki sieciowe i pasujące wtykowe
gniazdka sieciowe zmniejszają ryzyko poraże-
nia prądem elektrycznym.
b) Unikaj kontaktu fizycznego z powier-
zchniami uziemionymi takimi jak
powierzchnie rur, grzejników, kuchni
elektrycznych i lodówek. Istnieje podwyż-
szone niebezpieczeństwo porażenia prądem
elektrycznym, gdy twoje ciało jest uziemione.
c) Trzymaj urządzenie z daleka od desz-
czu i wilgoci. Wniknięcie wody do urządzenia
elektrycznego zwiększa ryzyko porażenia prą-
dem elektrycznym.
d)
Nie używaj kabla sieciowego w
sposób sprzeczny z jego prze-
znaczeniem, tj. do noszenia
urządzenia, zawieszania urzą dzenie
lub do wyciągania wtyku sieciowego
z wtykowego gniazdka sieciowego.
Trzymaj kabel z daleka od gorąca,
oleju, ostrych krawędzi lub porusza-
jących się części urządzeń. Uszkodzone
lub poplątane kable zwiększają ryzyko pora-
żenia prądem elektrycznym.
e)
Gdy pracujesz z urządzeniem elektrycz-
nym na dworze używaj wyłącznie
przedłużaczy, które są dopuszczone
również do pracy na dworze. Użycie
przedłużacza przystosowanego do stosowania
na dworze zmniejsza ryzyko porażenia prądem
elektrycznym.
f) Jeśli praca elektronarzędzia w otocze-
niu wilgotnym jest nie do uniknięcia,
należy zastosować wyłącznik prądu
uszkodzeniowego. Zastosowanie wyłącz-
nika prądu uszkodzeniowego zapobiega nie-
bezpieczeństwu porażenia prądem elektrycz
nym.
3. Bezpieczeństwo osób
a) Bądź stale uważny, zwracaj uwagę
na to co robisz i postępuj rozsądnie w
trakcie pracy z narzędziem elektrycz-
nym. Nie używaj narzędzia, gdy jesteś
zmęczony lub znajdujesz się pod
wpływem narkotyków, alkoholu lub
lekarstw. Chwila nieuwagi przy użytkowaniu
urządzenia może prowadzić do poważnych
obrażeń ciała.
b)
Noś osobiste wyposażenie
ochronne i zawsze okulary
ochronne. Noszenie osobistego
wyposażenia ochronnego takiego jak maska
przeciwpyłowa, buty antypoślizgowe, kask
ochronny lub ochrona słuchu stosownie do
sposobu użytkowania narzędzia elektrycznego
zmniejsza ryzyko obrażeń ciała.
c) Unikaj niezamierzonego uruchomienia.
Upewnij się, że narzędzie elektryczne
jest wyłączone zanim podłączysz je
do zasilania prądowego, uchwycisz je
lub będziesz je przenosił. Jeżeli podczas
przenoszenia urządzenia będziesz trzymał
palec na przełączniku WŁĄCZ. / WYŁĄCZ.
lub jeżeli urządzenie jest włączone, to może
to prowadzić do nieszczęśliwych wypadków.
19 PL
Ogólne wskazówki bezpieczeństwa dla elektronarzędzi
Ogólne wskazówki bezpieczeństwa dla elektronarzędzi
d) Usuń narzędzia do nastawiania urzą-
dzenia lub klucze płaskie zanim włą-
czysz urządzenie. Narzędzie lub klucz,
który znajduje się w obracającej się części
urządzenia może prowadzić do obrażeń ciała.
e) Unikaj nienormalnej postawy ciała.
Zadbaj o pewne stanowisko i w każdej
chwili utrzymuj równowagę. Dzięki temu
będziesz mógł lepiej kontrolować urządzenie,
zwłaszcza w nieoczekiwanych sytuacjach.
f) Noś odpowiednią odzież. Nie noś ob-
szernej odzieży ani biżuterii. Trzymaj
włosy, odzież i rękawice z daleka od
poruszających się części. Luźna odzież,
biżuteria lub długie włosy mogą zostać uchwy-
cone przez poruszające się części.
g) Jeżeli zostaną zamontowane urzą-
dzenia do odsysania i wychwytywania
pyłu, to upewnij się, że są one podłą-
czone i że będą prawidłowo używane.
Używanie tych urządzeń zmniejsza zagrożenie
wywoływane pyłem.
4.
Staranne obchodzenie
się i użytkowanie narzędzi
elektrycznych
a) Nie przeciążaj urządzenia. Używaj
do swojej pracy przeznaczonego do
niej narzędzia elektrycznego. Za pomo-
cą odpowiedniego narzędzia elektrycznego
pracujesz lepiej i bezpieczniej w danym zakre-
sie robót.
b) Nie używaj żadnego narzędzia elek-
trycznego, którego przełącznik jest
uszkodzony. Narzędzie elektryczne, które
nie daje się już więcej włączyć lub wyłączyć,
jest niebezpieczne i musi zostać naprawione.
c) Zanim przeprowadzisz nastawy urzą-
dzenia, wymienisz części osprzętu lub
odłożysz urządzenie wyciągnij wtycz-
kę sieciową z sieciowego gniazdka
wtykowego. Ten środek ostrożności zapo-
biega niezamierzonemu startowi urządzenia.
d) Przechowuj nieużywane narzędzia
elektryczne poza zasięgiem dzieci. Nie
pozwól na użytkowanie urządzenia
osobom, które nie są z nim obznajo-
mione lub nie przeczytały niniejszych
instrukcji. Narzędzia elektryczne są niebez-
pieczne, gdy są używane przez osoby niedo-
świadczone.
e) Pielęgnuj starannie urządzenie.
Sprawdź, czy ruchome części urzą-
dzenia funkcjonują nienagannie i nie
zakleszczają się, czy części urządze-
nia nie są złamane lub uszkodzone w
takim stopniu, że funkcjonowanie
urządzenia jest uszczuplone. Zleć
naprawę uszkodzonych części przed
użyciem urządzenia. Przyczyną wielu
wypadków są źle konserwowane narzędzia
elektryczne.
f) Utrzymuj narzędzia tnące w stanie
ostrym i czystym. Starannie pielęgnowane
narzędzia tnące o ostrych krawędziach tną-
cych mniej zakleszczają się i dają się łatwiej
prowadzić.
g) Używaj narzędzia elektrycznego,
osprzętu, narzędzi wymiennych itp.
odpowiednio do niniejszych instrukcji
i w taki sposób, jaki jest zalecany dla
tego specjalnego typu urządzenia.
Uwzględniaj przy tym warunki robo-
cze i wykonywane czynności. Użycie
narzędzi elektrycznych do innych zastosowań
niż to przewidziano może prowadzić do nie-
bezpiecznych sytuacji.
Wskazówki dotyczące
bezpieczeństwa dla
szlifierki taśmowej
Niniejsze urządzenie należy trzymać
na
izolowanych powierzchniach uchwytόw
,
jako że taśma szlifierska może uszko-
dzić własny przewόd sieciowy. Uszko-
dzenie przewodόw przewodzących prąd elek-
tryczny może spowodować, że metalowe części
urządzenia znajdą się pod napięciem oraz do-
prowadzić do porażenia prądem elektrycznym.
ZAGROŻENIE POŻAROWE WSKUTEK
WYRZUCANIA ISKIER! Gdy szlifowane są
metale postaje wyrzut iskier. Dlatego też należy
20 PL
Uruchomienie / Obsługa
Ogólne wskazówki bezpieczeństwa dla elektronarzędzi / Uruchomienie
bezwzględnie zwracać uwagę na to, żeby nie
zostały zagrożone żadne osoby oraz żeby w
pobliżu obszaru roboczego nie znajdowały się
żadne palne materiały.
Przy obróbce drewna, a zwłaszcza, gdy obra-
biane będą materiały, w przypadku których
powstają szkodliwe dla zdrowia pyły, należy
podłączyć odpowiednie zewnętrzne urządzenie
odsysające.
Przy obróbce tworzyw sztucznych, farb,
lakierów itp. należy zadbać o wystarczające
napowietrzanie.
Szlifierka taśmowa jest zaprojektowana do szli-
fowania powierzchniowego na sucho drewna,
tworzywa sztucznego, metalu i masy szpachlowej
oraz powierzchni lakierowanych. Urządzenie
wolno stosować tylko do szlifu suchego.
Materiału zawierającego azbest nie wolno ob-
rabiać. Azbest jest uznawany za rakotwórczy.
TRUJACE PYŁY! Powsta-
jące przy szlifowaniu na przykład powłok ma-
larskich zawierających ołów, niektórych rodzajów
drewna oraz metali szkodliwe / trujące pyły
stanowią zagrożenie zdrowia dla osoby obsłu-
gującej urządzenie lub dla osób znajdujących
się w pobliżu.
Noś okulary ochronne i maskę
przeciwpyłową!
Zabezpieczaj przedmiot obrabiany. Używaj
urządzenia mocującego / imadła, aby przy-
trzymać przedmiot obrabiany. W ten sposób
jest on przytrzymywany pewniej niż ręką.
W żadnym wypadku nie opieraj rąk obok lub
przed urządzeniem oraz przed obrabianą
powierzchnią, ponieważ w razie ześlizgnięcia
istnieje niebezpieczeństwo obrażeń ciała.
W przypadku niebezpieczeństwa wyciągnij
natychmiast wtyczkę sieciową z wtykowego
gniazdka sieciowego.
Zawsze prowadź kabel od urządzenia do tyłu.
Unikaj kontaktu z biegnącą taśmą szlifierską.
Nie obrabiaj żadnych zwilżonych lub wilgot-
nych powierzchni.
Urządzenie należy prowadzić zawsze w stanie
włączonym do przedmiotu obrabianego. Po
obróbce należy podnieść urządzenie z przed-
miotu obrabianego i dopiero wtedy je wyłączyć.
W trakcie obróbki zawsze trzymaj urządzenie
mocno oburącz (zobacz również rysunek D).
Zadbaj o pewną podstawę.
Pozwól, aby urządzenie całkowicie zatrzymało
się i wyłącz je zanim je odłożysz.
Podczas przerw w pracy, przed wszelkimi ro-
botami na urządzeniu (na przykład wymiana
papieru ściernego)oraz w przypadku nieużyt-
kowania urządzenia należy zawsze wyciągnąć
wtyk sieciowy z wtykowego gniazdka sieciowego
.
Q
Uruchomienie
Q
Zamocowanie / wymiana
taśmy szlifierskiej
NIEBEZPIECZEŃSTWO
POWSTANIA OBRAŻEŃ! Zawsze wyciągnij wtyk
sieciowy z wtykowego gniazdka sieciowego zanim
przystąpisz do wykonania robót na szlifierce taśmowej.
1. Najpierw należy poluzować zamocowanie
taśmy szlifierskiej odchylając całkowicie dźwi-
gnię
9
(patrz rys. A). Zamocowanie jest teraz
otwarte i można wyjąć taśmę szlifierską.
2. Teraz należy założyć nową taśmę szlifiers
względnie wymienić ją, aby obrabiać inny
materiał lub zmienić ziarnistość.
WAŻNE: Kierunki strzałek na stronie wewtrz-
nej taśmy szlifierskiej oraz na obudowie urzą-
dzenia muszą być zgodne.
3. Naciśnij znowu dźwignię mocująca
9
w pozycję wyjściową.
Ustawianie taśmy szlifierskiej:
Proszę podnieść urządzenie, włączyć je i obró-
cić. Następnie należy ustawić przebieg taśmy
obracając śrubę regulacyjną
6
tak, aby kra-
wędź taśmy przylegała do krawędzi urządze-
nia i była do niej równoległa (rys. B).
WAŻNE: Zwracaj bezwzględnie uwagę na
to, żeby taśma szlifierska nie ocierała się o
obudowę. Sprawdzaj regularnie bieg taśmy i w
razie potrzeby wyreguluj go za pomocą śruby
justującej
6
.
1 / 1

Parkside PBS 900 A1 Operation and Safety Notes

Kategoria
Szlifierki elektryczne
Typ
Operation and Safety Notes

w innych językach