Silvercrest SILVERCREST KH 2375 Operating Instructions Manual

BLUETOOTH CAR RADIO

Operating instructions

RADIO SAMOCHODOWE BLUETOOTH

Instrukcja obsługi

BLUETOOTH AUTÓRÁDIÓ

Használati utasítás

4A

KH 2375

KOMPERNASS GMBH · BURGSTRASSE 21 · D-44867 BOCHUM

www.kompernass.com

ID-Nr.: KH2375-01/08-V2

BLUETOOTH CAR RADIO

CV_KH2375_JOE23352_LB4A.qxd 04.07.2008 11:21 Uhr Seite 1

KH 2375

2*

2&2^

2^

3)

2(

B

2%

3^ 3%

C

3@

3*

3$

3!

3#

3&

2$ 2@ 2! ; l k j h g f d s a o

A

w

e r t y iuq

2# 2)

D

F

G

H

I

E

3(

4!

4) 4@

5&

5^

5$

5@

5)

5%

5#

5!

4^

4%

4*

4&

4$

4(

4#

6!

5(

5*

6)

CV_KH2375_JOE23352_LB4A.qxd 04.07.2008 11:21 Uhr Seite 5

- 1 -

CONTENT PAGE

Intended Use 3

Technical Data 3

Items supplied 3

Safety information 4

Operating Elements 5

Installation 6

Connection 6

Configuration of the ISO connections............................................................................................7

Installing the radio into the ISO duct ............................................................................................7

Connection schematic......................................................................................................................8

Connecting an external audio device to the car radio 8

Disassembling the device 8

Face plate 9

Remote control 9

Inserting the battery .........................................................................................................................9

Operation 10

Basic operation ..............................................................................................................................10

Volume ............................................................................................................................................10

Bass/Treble/Balance/Fader.........................................................................................................10

Loudness..........................................................................................................................................10

Display ............................................................................................................................................10

Setting the operating mode ..........................................................................................................10

RESET - Reset the radio..................................................................................................................10

Settings for the multi controller .....................................................................................................11

Radio functions 11

Selecting the band range..............................................................................................................11

Automatic station search ...............................................................................................................11

Programming stations.....................................................................................................................12

Accessing the station .....................................................................................................................12

Automatic saving ...........................................................................................................................12

IB_KH2375_JOE23352_LB4A 04.07.2008 11:15 Uhr Seite 1

- 2 -

Running through saved stations....................................................................................................12

Alternative Frequency (AF)............................................................................................................12

PTY (Programme Type Code Programme type/kind identification) .......................................12

TA ("Traffic Announcement") - TRAFFIC RADIO..........................................................................13

Playing audio CDs 13

Inserting and removing CDs .........................................................................................................14

Title skip ..........................................................................................................................................14

Fast forward/backward ................................................................................................................14

Stopping a CD ...............................................................................................................................14

Repeating a title .............................................................................................................................14

Title sampling..................................................................................................................................14

Random playback of all titles .......................................................................................................14

Playing MP3-CDs 14

Title search (by numbers) ..............................................................................................................15

Search for directories ....................................................................................................................15

USB port 16

Card reader 16

Record function 16

Bluetooth operation 17

Connection......................................................................................................................................17

Coupling a telephone with the car radio....................................................................................17

Using the microphone....................................................................................................................18

Operation .......................................................................................................................................18

Audio streaming (A2DP) ...............................................................................................................18

Replacing the fuse 19

Troubleshooting 19

Cleaning 20

Disposal 20

Warranty and Service 21

Importer 21

Read the operating instructions carefully before using the appliance for the first time and preserve this

booklet for later reference. Pass the manual on to whomsoever might acquire the appliance at a later date.

IB_KH2375_JOE23352_LB4A 04.07.2008 11:15 Uhr Seite 2

- 3 -

BLUETOOTH CAR RADIO

KH 2375

Intended Use

This device is designed for the reception of FM/AM

radio stations as well as for the playback of audio

and MP3-CDs, MP3 data from USB data carriers

and SD/MMC memory cards and also audio signals

from external audio devices. In addition you can con-

nect the car radio to a bluetooth mobile telephone

and, with the microphone unit, you can use the car

radio as hands free equipment. This device is intended

for use only in private environments. It is not suitable

for use in commercial or industrial areas.

Technical Data

Input voltage : 12V

Input current: max. 10 A

Impulse rating: 4 x 40 W

Radio frequency range:

Radio: FM (USW) : 87.5 - 108 MHZ

AM (MW) : 522 – 1620 KHz

Station memory slots: 18 FM (USW)

12 AM (MW)

Remote control:

Battery: 3 V Button cell (CR2025)

Audio input (AUX IN):

3,5 mm Stereo jack plug

USB port

USB 1.1 and 2.0 compatible data carrier

Card slot

SD/MMC memory card slot

Device fuse:

10 A Automotive flat fuse

General

Operating temperature range: +5°— +40°C

Humidity: 5 — 90% (no condensation)

Dimensions

(L x D x H): 18,8 x 19,2 x 5,7 cm

Weight : approx. 1345 gr

CE Conformity

This device complies with the basic requirements

and other relevent regulations regarding con-

formity to the automotive directive 2004/104/

EG and the directive R&TTE 99/5/EG.

Items supplied

- Car radio (incl. face plate)

- Installation bracket (Attached)

- Bezel frame (Attached)

- Fixture plate (incl. securing material)

- Remote control

- 1 Battery CR2025, 3 V DC

- Key for installation bracket

- Case for face plate

- Microphone unit with adhesive strip

- Operating manual

IB_KH2375_JOE23352_LB4A 04.07.2008 11:15 Uhr Seite 3

- 4 -

Safety information

• This device is not intended for use by individuals

(including children) with restricted physical, physio-

logical or intellectual abilities or deficiences in

experience and/or knowledge unless they are

supervised by a person responsible for their safety

or receive from this person instruction in how the

device is to be used.

• Children should be supervised to ensure that they

do not play with the device..

• Keep batteries away from children. Children can

put batteries into their mouths and swallow them.

If a battery is swallowed medical assistance must

be sought immediately.

To avoid damage through short circuits:

• If possible have the car radio installed by a qualified

technician.

• Only connect the device to a properly installed

12 V automotive battery. Only connect the car

radio in the vehicle via an ISO plug.

• Make sure that during operation the connection

cable can never become wet or moist. Run the

cable in such a way that it cannot become clamped

or damaged in any other way.

• To avoid possible dangers exchange damaged

cables or connectors immediately at an authorized

specialist establishment or the customer service

department.

• Only use the device in a vehicle interior.

• Make sure that liquids or objects are never able

to enter into the device.

• Do not open the housing or attempt to repair the

device yourself. Should you do so, device safety

can no longer be assured and the warranty will

become void.

Repairs are to be carried out exclusively by a

specialist firm or the service centre.

Information regarding the handling

of batteries

The remote control for this device uses a battery.

For the handling of batteries please observe the

following:

Risk of explosion!

Do not throw batteries into a fire. Do not re-

charge the batteries.

• Never open batteries, never solder or weld

batteries.

The risk of explosions and injuries exists!

• Regularly check the condition of the batteries.

Leaking batteries can cause damage to the device.

• Remove the batteries if you do not intend to use

the device for an extended period of time.

• Put on protective gloves when handling a leaking

battery.

• Keep batteries away from children. Children can

put batteries into their mouths and swallow them.

If a battery is swallowed immediately seek medical

assistance.

• Clean the battery compartment and the battery

contacts with a dry cloth.

To avoid the risks of fire or injury:

• Install the device in such a way as to avoid the

development of heat accumulation and so that

the device is sufficiently ventilated.

• Never cover the ventilation openings!

• Avoid any additional heat build up, e.g. direct

sunlight, heaters, other devices, etc.

• Do not operate the device if it has sustained a

fall or is damaged. Arrange for the device to be

checked and/or repaired by qualified technicians.

IB_KH2375_JOE23352_LB4A 04.07.2008 11:15 Uhr Seite 4

- 5 -

Danger laser radiation!

The device is fitted with a "Class 1 Laser".

• Never open the device.

• Never attempt to repair the device. There is

invisible laser radiation inside the device.

• Avoid all direct optical contact with the laser

beam, it could lead to serious eye injuries.

Traffic safety

Traffic safety is the number one priority. Only

operate your car radio when the traffic situation

allows. Familiarize yourself with the device be-

fore driving. Acoustical signals from the police,

fire service and other emergency services must

be able to be heard inside the vehicle in good

time. Therefore moderate the programme's

volume during the journey.

Operating Elements

Front panel (face plate)

q

BND/ENT: Select band range/confirm selection

w

POWER/DIM: Switch device on and off/dim display

illumination

e

MD/LD: Set operating mode/switch to loudness

r

Multi controller: Press to access the bass, treble,

balance and fader settings/turn

to set the value/volume

t

Display

y

Unlocking the face plate

u

DISP: Show display information

i

Card slot for SD/MMC cards

o

USB port

a

AUX IN: 3,5 mm stereo input socket for the con-

nection of an external audio device

s

A/PS: Automatic station saving

A

d

PTY ("Programme Type"): Station search by

PTY group

f

TA ("Traffic Announcement"):

Activate traffic radio station

/ END-button

g

AF ("Alternative Frequency"): Alternative

Frequency search

1%

Station button 6/next directory

j

Station button 5/previous directory

1&

RDM/4: Random playback in the CD/MP3

operation mode, station button 4

l

INT/3: Intro function in the CD/MP3 operation

mode, station button 3

1(

RPT/2: Repeat function in the CD/MP3

operation mode, station button 2

2)

Remote control sensor

2!

PAU/1: Stop playback in the CD/MP3

operation mode, station button 1

2@

/: Title/Station search backwards/forwards

2#

MU: Switch sound off/ACCEPT-button

2$

SCN/REC: Automatic station search/Record to

a data carrier at the USB port or the

SD/MMC card slot

Behind the face plate

2%

OPEN : Eject disc

2^

Holder for the face plate

2&

RESET: Reset the car radio

2*

Anti theft LED

2(

CD compartment's position LED

3)

CD compartment

Connections, rear panel

3!

ISO-Block connection B

3@

Automotive flat fuse 10 A

3#

ISO-Block connection A

3$

Microphone unit socket

3%

Bluetooth antenna

3^

Securing screw

(incl. M5 nut and washer)

3&

LINE OUT: Audio cinch output L/R for amplifier

3*

Antenna connection for a DIN antenna plug

C

B

IB_KH2375_JOE23352_LB4A 04.07.2008 11:15 Uhr Seite 5

- 6 -

Remote control

3(

POWER/DIM: Switch device on and off/dim

display illumination

4)

END-button

4!

/: Title/Station search backwards/forwards

4@

ACCEPT-button

4#

VOL+/-: Volume increase/decrease

4$

INT/3: Intro function in the CD/MP3 operation

mode, number button 3

4%

PTY/7: ("Programme Type") Station search by

PTY group/number button 7

4^

Number button 6

4&

DSP/

*

: ("Digital Sound Processing") Sound

settings/ button

*

4*

BAND/0: Select band range/number button 0

4(

Battery compartment

5)

SEL/#: Access settings for volume, bass, treble,

balance and fader/ button #

5!

TA/9: ("Traffic Announcement"): Activate traffic

radio station/ number button 9

5@

AF/8: ("Alternative Frequency"): Alternative

frequency search/ number button 8

5#

Number button 5

5$

RDM/4: Random playback in the CD/MP3

operation mode/ number button 4

5%

RPT/2: Repeat function in the CD/MP3 operation

mode/ number button 2

5^

/1: Playback start or stop/ number button 1

5&

MODE: Set operation mode/loudness function

Microphone unit

5*

green LED for connection status

5(

TALK button

6)

Microphone

6!

Microphone unit plug

Case for face plate

Key for installation bracket

Installation bracket

Bezel frame

I

H

G

F

E

D

Installation

If you want to install your car radio yourself follow

the installation and connection instructions in this

manual.

Installation instructions

• Insert the device in the slot provided for it or select

a location for mounting the device that does not

obstruct the driver during normal operation of

the vehicle.

• Briefly connect the cable before finally installing

the device. Make sure that it is plugged in properly

and that the system functions correctly.

• In the event that changes to the vehicle are ne-

cessary contact your vehicle dealer/qualified

radio installation facility.

• Install the device in such a way as to avoid in-

juries in the event of harsh braking.

• If the device is installed with more than a 30° in-

clination it could lead to function disorders.

• Avoid installation of the device in the vicinity of

high temperature sources (i.e. direct sunlight or

heating vents) or dusty and dirty locations. Do

not subject the device to excessive vibration.

Connection

Note:

Make sure that a permanent positive connection

is applied to the station memory of connection

6 in the ISO block A.

You can connect an external amplifier to the

audio cinch output. For this follow the operating

instructions for the external amplifier.

IB_KH2375_JOE23352_LB4A 04.07.2008 11:15 Uhr Seite 6

- 7 -

Configuration of the ISO connections

Of course you can also only connect the car radio

to two speakers. Then you only use the cable for the

front speakers.

Problems because of cable interchanging

In a few vehicle models the standard configura-

tion of the connections [4] and [6] in the ISO

Block A (see above "Configuration of the ISO

Blocks") is interchanged at the factory. If this is

the case the station memory can be lost.

To correct this the connections 4 (Ignition positive)

and 6 (Permanent positive) in the ISO Block A must

be swapped.

Installing the radio into the ISO duct

Note

Before installation remove, without fail, the two

transport securing screws on the top of the radio

housing (marked with a red sticker)!

1234

5678

ISO A

Configuration

1 unconfigured

2 unconfigured

3 Antenna power

4 12 V (Ignition

positive)

5 unconfigured

6 Permanent positive

7 unconfigured

8 Minus (-)

1234

5678

ISO B

Configuration

1 Rear right +

2 Front right +

3 Front left +

4 Rear left +

5 Rear right -

6 Front right -

7 Front left -

8 Rear left -

The car radio can be installed into any standard

ISO mounting duct. In the event that your vehicle

does not have an ISO mounting duct contact your

local specialist establishment, local dealer or the

technical department of the store.

• Pull the installation bracket and the bezel frame

off of the car radio's housing.

• Place the installation bracket into the ISO mounting

duct.

• Bend the tabs on the installation bracket with a

screw driver so that the bracket is fixed firmly

into the mounting duct (see diagram).

• Check to make sure that the bracket is securely

fixed.

• Connect the ISO socket block of the car radio with

the two ISO plugs on your vehicle.

• Connect the antenna cable from the vehicle an-

tenna to the antenna socket on the car radio.

• Feed the microphone unit cable into the mounting

duct and connect it to the microphone unit socket.

Run the cable in such a way that the microphone

unit can later be secured in the vehicle interior.

• Contingently connect the audio cinch cable of

an external amplifier to the

LINE OUT socket on the

car radio.

• If necessary secure your device against theft

with additional measures. Attach the securing

screw with the anchoring plate and the securing

material to the engine firewall of the vehicle.

• Carefully push the car radio into the mounting

duct until it locks into place. Finally put on the

bezel frame.

IB_KH2375_JOE23352_LB4A 04.07.2008 11:15 Uhr Seite 7

- 8 -

Attention!

For installation please use the car radio's ISO

connections. The vehicle specific ISO adapter

that you may possibly require can be obtained

from a specialist establishment, from a local

dealer or from the store's technical department.

When using other connection types the warranty

becomes void!

Observe the cable positioning when pushing

the radio in; it could become damaged.

Antenna power connection

The connection for the antenna power is available

for a relay controlled antenna. The relay then

automatically extends the antenna when the radio

is switched on. When switched off the antenna

retracts.

This connection can also be used to control an

external amplifier. For exact connection informa-

tion please consult the amplifier's operating in-

structions.

Never attach the antenna power connection with

the antenna's motor power cable; this can cause

damage to the radio!

Backup connection

Make sure that for the station memory the per-

manent positive is applied to the connection 6

in the ISO block A. Otherwise you will not be

able to save any radio stations!

• After all connections have been made activate the

RESET button with a ball point pen or other pointed

object.

• Attach the face plate as described under

“Putting the face plate in”.

Connection schematic

Connecting an external audio

device to the car radio

• Connect the audio output of an external audio

device (i.e. an MP3 player) via a 3.5 mm stereo

jackplug to the socket

AUX IN on the front panel of

the device.

• Select playback of the audio input by pressing,

several times, the

MD/LD button until AUX is

shown in the display.

Disassembling the device

• To disassemble the device first remove the bezel

frame and then feed the right and left keys into

the respective slots on the sides of the device.

The tabs are now bent back and you can pull the

device out.

1234

5678

1234

5678

ISO A

ISO B

Antenna

External amplifier

Microphone unit

IB_KH2375_JOE23352_LB4A 04.07.2008 11:15 Uhr Seite 8

- 9 -

Face plate

Putting the face plate on

• Place the face plate with the left side in the frame

first. Then firmly press the right side until it locks

into place.

• Check to make sure that the face plate is firmly

and correctely installed in the frame. If the face

plate is incorrectely installed it can result in mal-

functions when operating the car radio.

Removing the face plate

• Press the button to unlock the face plate.

• To remove the face plate first tip it slightly forward

and pull the right side away first and then the left

side.

Note

When the face plate is not inserted into the frame

the theft protection LED on the device blinks.

To safeguard the face plate always keep it stored

in its case.

Remote control

Inserting the battery

Remove the supplied battery from the packing.

To insert the battery and/or change the battery

proceed as follows:

• Pull the battery compartment out of the remote

control by first pressing the lateral locking device

and then pulling the battery compartment out.

• Remove the depleted battery and insert a new

battery of the type CR2025 (Button cell) into the

battery compartment. Make sure that the battery

is inserted in accordance with its correct polarity.

• Slide the battery compartment back into the re-

mote control.

Using the remote control

• Point the remote control to the Infrared sensor

on the front panel of the device.

• You can use the remote control for distances of

up to approx. 8 m from the device.

IB_KH2375_JOE23352_LB4A 04.07.2008 11:15 Uhr Seite 9

- 10 -

Operation

Operation via the buttons on the

device and on the remote control

Most of the functions can be operated by the

buttons on the device as well as by the buttons

on the remote control. In these instructions the

buttons on the device are described.

If the buttons on the remote control are meant

this will be specifically mentioned.

Note

Approx. 5 seconds after a setting has been

made the playback will again be displayed

and the setting is saved.

Basic operation

Switching On and Off

Press briefly the POWER/DIM button to switch the radio

on. In the display the notice WELCOME appears.

• Briefly touch the

POWER/DIM button to dim the dis-

play illumination.

To switch off hold down the

POWER/DIM button longer.

Volume

• Turn the multi controller to increase or decrease

the volume.

Attention!

Always set the volume to a level that will allow

you, at any time, to clearly hear acoustical signals

from emergency service vehicles!

Bass/Treble/Balance/Fader

• Press the multi controller to display the current

settings for the Bass (BASS), Treble (TREBLE),

Balance (BALANCE) and Fader (FADER).

• Turn the multi controller to change the settings.

Loudness

• Hold down the MD/LD button to switch the loudness

function on or off.

Display

• By pressing the DISP button you can switch the notices

in the display around in the following manner:

With radio reception:

Programme name, time of day (will automatically

be set with RDS reception), PTY settings (these RDS

functions are transmitted by the broardcast institu-

tions in various extents; see also the chapter "Radio

functions") and frequencies.

In CD mode:

Time of day, PTY settings and frequencies.

Note

If you do not receive any RDS or PTY information

"PS NONE" or "PTY NONE" appears in the dis-

play. Each notice only appears for a few seconds.

Setting the operating mode

• Press the MD/LD button to switch between radio re-

ception (frequency indicator), CD/MP3 operation

(CD), card slot (SD/MMC), USB port (USB) and

audio input (AUX).

Note

The operating modes CD, SD/MMC and USB

can only be accessed when the corresponding

medium is inserted.

RESET - Reset the radio

• To reset the car radio to its factory default settings

press the

RESET button with a pointed object, for

example a ball point pen.

• Reset the car radio:

- at initial operation,

- after the cable connection,

- if not all function buttons are working

- when an error message appears in the display.

IB_KH2375_JOE23352_LB4A 04.07.2008 11:15 Uhr Seite 10

- 11 -

Settings for the multi controller

Via the multi controller you can, in addition, admi-

nister settings for the switch on volume, time of day

settings, traffic radio volume, EON function, recor-

ding format and the equalizer.

• Hold down the multi controller for approx. 2 se-

conds and then press it several times to access

the following settings:

INVOL - switch on volume

• Turn the multi controller in order to set a volume

level, which will apply when the car radio is

switched on.

ADJ - Time of day

Your car radio is equipped with an RDS controlled

clock. The clock sets itself automatically when the

EON function is switched on and also continues to

run when the radio is switched off. If you do not

receive any RDS signal you can also set the time of

day manually.

• Turn the multi controller to the right to set the

hours and to the left to set the minutes.

TAVOL - Volume for traffic radio

• Turn the multi controller in order to set a volume

level, which will apply when the traffic report is

switched on.

EON - Function

Turn the multi controller in order to switch the EON

function on (EON ON) or off (EON OFF). When

the EON function is switched on the radio switches

to traffic radio or PTY types if the TA or PTY function

has been switched on.

REC - Recording format

• Turn the multi controller to set the record format

for recording on SD/MMC and/or USB data

carriers, MP3 (MP3 data) or WMA (Windows

Media Audio).

DSP - Equalizer

• Turn the multi controller to select one of the set-

tings DSP CLASSIC, DSP ROCK, DSP POP, DSP

FLAT or DSP NONE. In the setting DSP NONE

no Digital Sound Processing (DSP) is switched on.

You can also set the equalizer by pressing the

DSP

button on the remote control. With this setting DSP is

switched off when the radio frequency is shown

again.

The DSP equalizer setting is shown at the bottom of

the display.

Radio functions

Selecting the band range

• Press the BND/ENT button to switch between USW

(FM1, FM2, FM3) and medium wave (MW1,

MW2).

Automatic station search

• Press briefly the search buttons  or  to start

a search forwards/backwards. The search stops

at the next station found.

Manual station selection

• When you hold down one of the buttons  or

 for two seconds you switch to manual station

search. MANUAL appears in the display.

• Now press the search buttons  or  several

times to set the frequency in steps of 0.05 MHz

(MW: 9 kHz) up/down.

If no button is pressed for approx. two seconds the

automatic station search is set again. AUTO appears

in the display..

IB_KH2375_JOE23352_LB4A 04.07.2008 11:15 Uhr Seite 11

- 12 -

Programming stations

• Press the BND/ENT button to set a band range.

In each range you can save six stations.

• Search for the station that you want to save.

• After the search has found a station press one of

the station buttons 1-6 for approx. three seconds.

The brief switching off of the sound indicates that

the station is saved.

The device switches back to radio playback after a

few seconds.

Accessing the station

• Select with BND/ENT the band range.

• By pressing one of the station buttons 1-6 you

access the saved station again.

Automatic saving

• Hold down the A/PS button. A search immediately

starts whereby each found station remains for

approx. five seconds. The blinking number in the

display shows the number of the station button,

on which will be saved the respective station.

With weak stations the search will automatically

continue.

• Whilst the search is stopped press a station button

to save the station on another memory position.

Running through saved stations

• You can access the saved stations of the current

station range.

• Select with

BND/ENT the band range.

• Press briefly the

A/PS button. All stations will be

briefly selected.

• When you hear the desired station press briefly

the

A/PS button.

Alternative Frequency (AF)

You can search for alternative frequencies of a station

so that it will always have optimal reception.

• Press the

AF button. The notice AF appears in the

display. Now the radio will always search for

the optimal radio frequency of the currently set

station.

Regional programmes

A few stations broadcast regional programmes.

• In order to playback only the station's regional

programme hold down the

AF button until the

notice REG ON appears in the display.

• To again playback the national programme hold

down the

AF button until the notice REG OFF ap-

pears in the display.

PTY (Programme Type Code Program-

me type/kind identification)

For this function the EON function must be switched

on.

• To activate the PTY search press the

PTY button.

In the display the notice PTY appears.

With the station search only stations of the currently

selected PTY identification (see the PTY identification

table) will be considered.

• To deactivate the PTY search press the

PTY button

again.

Setting the PTY identification

• Hold down the PTY button and then turn the multi

controller to set the individual PTY identifications.

Station search by PTY identification

• During the display of a PTY identification if you press

briefly the

PTY button or the buttons / a search

immediately starts for stations, which correspond to

this PTY identification.

If no station is found that corresponds to this PTY

identification the notice NOT FND appears briefly

and then the search ends with the last set station.

IB_KH2375_JOE23352_LB4A 04.07.2008 11:15 Uhr Seite 12

- 13 -

PTY identification

Please note that this information is dependent on the

region, the broadcasting corporation and the station.

PTY indicator Contents

1 NEWS News

2 AFFAIRS Politics & current events

3 INFO Special word programmes

4 SPORT Sport

5 EDUCATE Study & further education

6 DRAMA Radio play & literature

7 CULTURE Culture, church, social

8 SCIENCE Science

9 VARIED Conversational

10 POP M Pop music

11 ROCK M Rock music

12 EASY M Easy listening music

13 LIGHT M Light classical music

14 CLASSICS Serious classical music

15 OTHER M Special music programmes

16 WEATHER Weather

17 FINANCE Finance

18 CHILDREN Childrens programme

19 SOCIAL Social

20 RELIGION Religion

21 PHONE IN Caller broadcasts

22 TRAVEL Travel

23 LEISURE Leisure

24 JAZZ Jazz music

25 COUNTRY Country music

26 NATION M National music

27 OLDIES Oldies music

28 FOLK M Folk music

29 DOCUMENT Documentaries

30 TEST Display indicator "Alarm Test"

31 ALARM Alarm reports

TA ("Traffic Announcement")

- TRAFFIC RADIO

For this function the EON function must be switched

on.

• Press the

TA button briefly to switch this mode on

or off.

In the TA mode the device will immediately switch

from other stations or operation types to the radio

station, which is currently broadcasting traffic infor-

mation. With this the volume level entered under

TAVOL will be set.

The TA function can be stopped during the play-

back of traffic information, without switching off the

TA mode, by pressing the

TA button again.

Playing audio CDs

ASP "Anti shock protection"

The device is equipped with an anti shock function.

This function serves to compensate for vibrations,

for example on uneven streets, and to provide

an uninterupted playback even with device

movement. When the device is switched on

the memory automatically fills with data:

– with audio CDs for 10 seconds;

– with MP3-CDs for 120 seconds.

Further information for CD operation

Dampness and high humidity can cause the

CD player to malfunction. In this case switch on

the vehicle heating to dissipate the dampness

before using the device. Do not subject the CD

player to any extreemly high or low temperatures.

IB_KH2375_JOE23352_LB4A 04.07.2008 11:15 Uhr Seite 13

- 14 -

Inserting and removing CDs

• Fold the face plate downward by pressing the

face plate's unlocking device.

• Push the CD into the CD slot with the inscribed

side facing up.

• Lock the face plate back into place by folding it

upwards. Playback of the CD begins. TOC READ

appears in the display (Read directory contents).

• To remove the CD open the face plate again. Press

the

OPEN button.

The CD will be ejected. The car radio switches to

radio mode.

Attention!

Do not drive with an ejected CD. Immediately

remove the CD from the CD slot.

If an ejected CD is not removed within approx.

5 seconds the device will draw it back in, however

playback of the CD will not start.

Title skip

• By means of the button  or  you can select

the next and/or the previous title. The title number

will be shown in the display.

Fast forward/backward

• Hold down the buttons  or  longer to start

fast forward or backward.

Stopping a CD

• You can stop the playback with the PAU/1 button.

To continue playback press the

PAU/1 button once

more.

Repeating a title

• Press the RPT/2 button. In the display RPT ONE is

shown and then

RPT. The current title is repeated.

A repeat pressing launches the normal playback

(the entire disc is repeated). RPT ALL appears briefly

in the display.

Repeat function with MP3-CDs:

• Press the RPT/2 button. In the display RPT ONE is

shown and then RPT. The current title is repeated.

• Press the

RPT/2 button once more. RPT DIR will

appear in the display followed by RPT ALL. All

titles in the current directory will be repeated.

A repeat pressing launches the normal playback

(the entire disc is repeated). RPT ALL appears briefly in

the display.

Title sampling

• Press the INT/3 button. In the display INT will be

shown. Appox. 10 seconds from all titles will

playback one after the other. A repeat pressing

launches the normal playback.

Random playback of all titles

• Press the RDM/4 button. In the display RDM is

shown. A random controlled playback is started.

A repeat pressing launches the normal playback.

Playing MP3-CDs

The basic functions correspond to those of the audio

CDs (see previous chapter). However with MP3-CDs

you can select the titles and the interpreters directly.

These functions and the other MP3 specific functions

are definitivly dependent on the MP3-CD. Please

bear this in mind when creating these CDs (see the

next section).

All conventional codings can be played back.

TITLE > INTERPRET > ALBUM NAME >

RELEASE YEAR > COMMENTARY.

Note:

Creation of MP3-CDs; ID3TAGs

MP3-CDs like data CDs can contain individual

titles or directories. Please bear in mind with

the creation of an MP3-CD that you do not

save titles on the same level as directories but

rather only in the directory.

IB_KH2375_JOE23352_LB4A 04.07.2008 11:15 Uhr Seite 14

- 15 -

A mixture of titles and directories on the same

level can result in problems when playing

back.

With the creation of the MP3 file you can also

save the so called "ID3 tag" (for input we recom-

mend an ID3 tag editor). This is a block of infor-

mation that is contained in the MP3 file. This can

be, for example, information about the inter-

preters, titles, album name, release year and a

short commentary. The car radio can read this

block of information and show it in the display.

Title search (by numbers)

Title numbers search

• Press the A/PS button. The notice 001 appears in

the display.

The last digit of the three digit title input blinks.

• Turn the multi controller to enter the last digit of

the title number.

• Press the multi controller.

The second digit of the three digit title input blinks.

• Turn the multi controller to enter the ten's digit of

the title number.

• Press the multi controller.

The first digit of the three digit title input blinks.

• Turn the multi controller to enter the hundreds

digit of the title number.

• When you have entered the desired title number

confirm the entry with

BND/ENT. The title will im-

mediately playback.

Title name search (Letters)

• Press A/PS twice.

The notice A** blinks in the display. The first symbol

blinks.

• Turn the multi controller to enter a letter or number,

with which the title name begins. Press the multi

controller.

The next symbol blinks in the display.

• Turn the multi controller to enter the second letter

or a number. Press the multi controller.

The next symbol blinks in the display.

• Turn the multi controller to enter the third letter or

a number.

• Press the

BND/ENT button to show all titles that

begin with the sought after symbol.

• Turn the multi controller to select a title and start

playback with

BND/ENT.

Search for directories

Search from the current directory

• Press A/PS three times. The directory that is cur-

rently playing back appears.

• Turn the multi controller to show the available

MP3 directory and select a directory with the

BND/ENT button.

Playback of the first title from the selected directory

starts immediately.

Playback of the previous/next directory

• Press the station button 6 to playback the next

directory and/or the station button

5 to playback

the previous directory.

WMA files

The device can also play WMA files. The opera-

tion functions exactly the same as for MP3 files.

IB_KH2375_JOE23352_LB4A 04.07.2008 11:15 Uhr Seite 15

- 16 -

USB port

playback

You can connect an MP3 player or another USB

data carrier to the USB port on the front panel of

the device. Your car radio can handle USB data

carriers up to 1 GB. With this the directory structure

may contain a maximum of 1024 folders, 4096 files

and a directory depth of 8 levels.

• Remove the protective cap from the USB port.

• Connect your USB device to the port. The car

radio searches for MP3 or WMA files on the

data carrier and the notice USB appears in the

display.

• The operations for playing files on the external

data carrier as well as the search function are

exactly the same as with MP3-CDs.

• If the device is in another mode (CD or card

reader) you can select the USB port with the

MD/LD button.

• Place the protective cap back on the USB port

when no USB device is connected to avoid con-

tamination.

Card reader

Your car radio is equipped with a memory card slot

for SD and Multimedia cards.

playback

• Slide a memory card into the memory card slot

with the marking pointing to the right. Playback

of the MP3 or WMA title on the memory card

begins automatically.

• The operations for playing files, function exactly

the same as for MP3-CDs.

• If the device is in another mode (CD, Radio,

AUX or USB) you can select the card reader

with the

MD/LD button.

Record function

Note:

Please observe the legal regulations valid in

your place of residence regarding the duplica-

tion of copyrighted works. In case of doubt

please consult a specialist in your area.

Recording from audio CDs

With your car radio you can record files from the

CD player to an external USB data carrier or an

SD/MMC card.

• In audio CD mode hold down the

SCN/REC

button.

The notice USB ALL appears (When the recording

target is MMC SD/MMC ALL appears).

• Press the

SCN/REC button to select either the recording

option USB/MMC-ALL (Record all titles) or

USB/MMC -ONE (Record one title).

• Start recording by pressing the

BND/ENT button.

The audio file is now saved in the format set before-

hand (MP3 or WMA, see page 11 "REC settings -

recording format") on the data carrier. At the begin-

ning of the recording the notice RECORD appears

in the display.

After that the recording is characterized by a prefixed

"R".

Note

When the USB data carrier is full the recording

automatically switches to the card reader, so

long as a memory card is inserted (see the fol-

lowing chapter).

• To stop the recording press briefly the

BND/ENT

button once more. After WAIT is shown briefly in

the display, the recording is saved.

IB_KH2375_JOE23352_LB4A 04.07.2008 11:15 Uhr Seite 16

- 17 -

You can play the data again by switching to the

USB or SD/MMC mode with the

MD/LD button and

then accessing the corresponding title from the data

carrier.

Copying MP3 files

You can copy individual titles from an MP3-CD to

the external USB data carrier or an SD/MMC me-

mory card.

• During playback of a title from an MP3-CD hold

down the

SCN/REC button.

The notice COPY MMC appears.

• Press the

SCN/REC button several times to select

either the copy option COPY USB (copy to a

USB data carrier) or COPY MMC (copy to an

SD/MMC memory card).

• Start the copy process by pressing the

BND/ENT

button.

During the copy process COPY appears in the display

and a procentage indicator from 01 - 100 shows

the copying progress. After the notice COPY 100

the copying process is ended and playback of the

MP3 title continues.

Recording from the radio or audio input

With your radio you can also record data from the

radio and/or the audio input to a USB memory

stick or a memory card.

• Place a memory medium into the card slot or

USB port and with the

MD/LD button select the

radio mode or operation type AUX.

• If necessary start playback of the external audio

device.

• Hold down the

SCN/REC button.

The notice REC MMC appears.

• Press the

SCN/REC button several times to select eit-

her the recording option USB (Recording to a USB

memory medium) or MMC (Recording to an

SD/MMC memory card).

• Start the copy process by pressing the

BND/ENT

button.

• To stop the recording press briefly the

BND/ENT

button once more. After WAIT is shown briefly in

the display, the recording is saved.

Information regarding the recorded

data

The recording will be saved to the data carrier

with the following notations:

Audio CD recordings: Track01, Track02 ...

MP3-CD recordings: Music01, Music02 ...

Radio recordings: Tuner01, Tuner02 ...

Audio CD and radio recordings are recorded

in stereo and with a bitrate of 128 kbps

and/or a sampling frequency of 44 kHz.

When copying MP3 files the recording format

of the copy source will be adopted.

Bluetooth operation

Connection

• Connect the microphone unit to the car radio as

described under "Connection/Connection sche-

matics".

To use the microphone unit you need a mobile tele-

phone, which supports Bluetooth data transmissions.

Coupling a telephone with the car radio

• Carry out a search for Bluetooth devices on your

mobile telephone.

• After a successful search the entry CAR--BT appears

for the car radio in the display of the mobile tele-

phone.

• Select this entry for the connection and for the

subsequent password request enter the pass-

word 0000 for the car radio. You may possibly

have to confirm the connection structure once

more.

After a successful coupling CONNECT briefly appears

in the car radio's display and the green LED on the

microphone unit lights up.

IB_KH2375_JOE23352_LB4A 04.07.2008 11:15 Uhr Seite 17

- 18 -

Using the microphone

During the telephone call you will hear the caller

via the speaker connected to the car radio.

• For optimal transmitting of your voice place the

microphone unit close to you.

• Attach the microphone unit, for example, to the

dashboard. For this purpose you can use the

supplied sticky tape. In this case clean before-

hand dust and grease from the surface. The sticky

tape can be used for securing on almost all

smooth surfaces.

Operation

Call accept/end

With an incoming call you hear the call signal via

your mobile telephone, whilst in the car radio's dis-

play is shown the call number.

• You accept an incoming call by pressing the

TALK

button on the microphone unit or the ACCEPT

button on the remote control and/or on the front

panel.

• You end the telephone call by pressing the

TALK

button on the microphone unit again or by pres-

sing the

END button.

Rejecting a call

• With an incoming call press, for longer than

2 seconds, the

TALK button on the microphone

unit or press the

END button to reject the

call.

To call

• Press the ACCEPT button on the remote control.

A blinking cursor appears in the car radio's dis-

play.

• With the number buttons enter the telephone

number that you want to call.

• Press the

ACCEPT button again.

The number will be dialed.

Redial

• Hold down the TALK button on the microphone

unit or the

ACCEPT button on the remote con-

trol and/or on the front panel for approx. 2 se-

conds.

- If no call number was previously selected via the

remote control's number buttons REDIAL appears

briefly in the display and then the last number

dialed from the mobile telephone will be dialed.

- If one or more call numbers were already dialed

via the remote control's number buttons REDIAL

appears in the display.

Turn the multi controller or press the

VOL-/+ buttons

on the remote control to show the last 10 dialed

numbers one after the other.

Press the

ACCEPT button to dial the selected tele-

phone number.

Select the entry REDIAL and then press the

END

button to end redial.

Audio streaming (A2DP)

Your car radio uses the A2DP profile (Advanced

Audio Distribution Profile) and therefore can play-

back your mobile telephone's audio data.

• Select an audio file from your mobile telephone

and start the playback.

The entry A2DP appears in the car radio's display

and the audio file will playback via the car radio's

speaker.

Note

On the mobile telephone it may possibly be

necessary to switch playback via the Bluetooth

stereo headset.

For this read also, without fail, the operating in-

structions for your mobile telephone.

With a few mobile telephones the car radio

does not automatically switch to the A2DP

mode. In this case you switch to the A2DP

mode by pressing the MD/LD button several

times until the notice A2DP appears in the dis-

play.

IB_KH2375_JOE23352_LB4A 04.07.2008 11:15 Uhr Seite 18

Strona jest ładowana ...

Silvercrest SILVERCREST KH 2375 Operating Instructions Manual

Silvercrest SILVERCREST KH 2375 Operating Instructions Manual

w innych językach

Powiązane dokumenty

Inne dokumenty